Operating Manual
Contents
1. Current memory page It means the current status is memory functional mode so four images can be stored When the system is powered off the stored images will disappear In case images to be stored are over 4 the new image will overlap the old one Note When the system is operating in the cine reproducing functional mode it can be changed over to the image memory functional mode by pressing CTRL C in order e Storing an image e During real time image display scan an image e Press the freezing key to freeze the displayed image e Press the storage key 2 to store the current image into image memory 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 29 5 Note In case that there are four images in the image memory the current image will be stored to overlap the previously stored images in order e Review images stored in the image memory When several images exist in the image memory the trackball or fast moving keys gt can be used to observe images in the image memory one by one 3 15 2 FLASH Permanent Memory 8 frames Max With use of additional memory board user can store eight permanent images These images are stored in the FLASH memory and will remain even when the power is interrupted Therefore the useful images can be retained for doctor to refer later And with this permanent storage function the doctor don t need to bring a printer when go for out door checks as2. M srace Mi f a GAIN aa s e D Oe Foa Es 9 gt ETAk a Freeze Sno i Fig 3 Diagram of control panel Diagram of control panel is shown in Fig 3 1 Alphanumeric keys 2 Control key 3 Menu key 4 Annotation key 5 Patient ID number key 6 Gynecological data table selection key 7 Body marks key 8 Frequency steps selection key 9 Image processing selecting key 10 Measuring key 11 Storage control key 12 Set key 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 13 Track ball 14 End key 15 Focus points selection key 16 Depth control key 17 White black Left Right image reversing key 18 FREEZE key 19 Zooming key 20 B mode switching key 21 B B mode switching key 22 B M mode switching key 23 M mode switching key 24 Total gain selecting key 25 CAPSLOCK key 26 SHIFT key 27 Far gain selecting key 28 Near gain selecting key 29 Clear key 30 Power indicator light 2 8 Installation a Open the packing box take out the main unit and place it steadily on a table b Connect the plug of probe cord to the probe socket also called probe connector at the rear of the main unit and tighten the probe handle The probe cord has an easy to connect plug When fitting the probe first please check the small protuberant lock pin inside the plug and the corresponding slot inside the socket make sure that
3. A a O rai 25 3 10 Name of hospital and ID COMMON cccoooccnnncccnnonccononanonnncnnoncnnnnncnnnnnc cnn nccnnnnnos 26 3 10 1 Entry of characters for comment 20 tdi ts 26 Entry of name Of hospital is c scsacsessccecsscosesstaasd cctvsssdcaeacededea n n 26 ID mdication rei lied 26 COmMent MALES AS IAS 26 3 10 2 Body mark selection and probe mark turnover ooooooccnnocccnnocccononccnnoncnnnnnccnnos 27 ZAL RECON eii ii 27 3 12 Seting OF reale AA E aan aia 27 3 13 Selection of beam sampling puncture guide ooooonnocccnoncccnonccononcnononcnonanacinnanos 28 3 14 Function of green environment protection ssssssessesesreresseseresessresseserssresee 28 3 15 Usage of cine memory card Optional ooooconncccnnonccinocccnnncccnnnccnnnncnnnnncnnnnos 28 As Maintenance si is mni pi ii o 32 O ce A oe 32 AA 32 A AAA ees daa Gees ierit eaen is a EE EENES EEEE E aas eae 33 A A Replacement of TUSE O ES 34 4 5 EMC electromagnetic compatibility ooooonnncccnnncocnnococonaccnnoncnononanonanccnnnnccnnnnnos 34 4 6 Requirement of environmental protection sesessseeessseessressersseesseresseeesres 34 4 1 Precision measurement utili ica 34 IO A a NT 35 OLA e T E 36 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL Chapter 1 General Description 1 1 Purpose of use The 600VET is an advanced and high quality veterinary ultrasound diganostic system developed by adopting the most up to date technologies of sound bio medical engineer
4. By properly adjusting focus a clear image can be displayed in a certain target area during real time image display of any mode The focus setting is shown behind Fo at the upper right portion of the screen Focuses of Near field Middle field Far field 1 and Far field 2 are indicated as the corresponding digital codes 1 2 3 4 When a certain focus is taken the corresponding digit code will be shown behind FO at the upper right portion of the screen When the selected focus is cancelled the corresponding digit code will be blanked off During B or B B mode image display multi stage focus can be selected However selection of too many focuses will cause the displayed image to flash Normally three focuses are recommended for use Operating procedure In the two modes of image displays focus is selected by using the FOCUS control The left key of FOCUS is used for selecting a single focus and the right one for changing combination of multiple focuses in turn e During the M mode and B M mode image displays only a single focus can be 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 17 selected In the two modes of image displays focus can only be changed over in the sequence of 1 2 3 4 with the FOCUS control 3 7 Image storage and recovery 3 7 1 During B mode image display one image can be stored for comparison later After the image is stored when power is off or a new image is st
5. HOSP At that time doctor can enter name of hospital In hospital name area up to 26 characters can be written in When name of hospital has been written in press the ENDI key to exit from the state of entry After this each time the system is started up the entered name will be automatically displayed unless it is altered By pressing the CTRL S key name of hospital can be rewritten e ID indication During frozen image display press the key and then the cursor appears at the last row on the screen for operator to write in animal s name and ID number Each time a character is written above the flashing cursor the cursor moves a step rightward The cursor can move fast under the control of the cursor fast moving keys gt _ or track ball Up to 33 characters can be written in the ID area e Comment in image area a During frozen image display press the E key and the cursor appears at the upper left portion of the screen Use the moving keys or trackball to move the cursor to the position for comment At that time characters or result can be written in the 600 VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 26 same way as ID entering In the state of comment in image area the cursor can be moved in the entire image area 3 10 2 Animal body mark selection and probe mark rotation At image fr
6. MPA 818 1 C00 E AE 16 S25 2 DE tlh CHANGE si rs ias 16 3 6 Image A uae ty ake aac Rd Muni AEE 17 SG 1 Image freezing variada latente tilda 17 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 3 6 2 Selection of scanning direction ica 17 3 6 3 Image black white up down TevVersiO8 ccococccnnoccconocccnonccnnnncconanacinnncn no 17 3 64 FOCUS sele cOn eee cae eG E EER 17 3 7 Image storage and recovery essssesseessersseseseeessetesstessresseesseeessseessresseesseeeseet 18 3 8 Measurement and calcula AER 18 3 8 1 Measurement and calculation in B B B mode operating states 18 Dist nc Mmedsurement iranran iai i E EE S 18 Measurement of circumference and area tracing method ooocoonncccnnnccinncccnnnos 19 Measurement of circumference and area elliptical method 0 0 eee 20 Volume measurement three axis method cocooooocconccncnnononananonocccncanananannnonon 20 3 8 2 Measurement and calculation in B M M mode operating states 21 Distance measurement tia 21 A AM A nue toluene dae 21 3 9 Reproduction measurement for animal gestation age and EDD ooooonnnncccnnnccccnns 22 3 9 1 Measure bovine gestation age and EDD ooooonocccinaccconucccnoncconnnanonnccnnnnccnnnnoss 22 3 9 2 Measure Equine gestation Ati A iia 23 39 3 Measure Ovine Set Ai 24 3 9 4 Measure canine gestation age and EDD ooooocconoccccnccccnonccononcnonnncnonnncnnonnccnnnos 24 3 9 5 Measure feline gestation A
7. Obtain useful image b Press the FREEZE key to freeze the image c Press the IMEAS key and use the direction keys gt or alphanumeric key 1 to select ELL at the lower portion of the screen d Press the SET key and then a corresponding small mark appears in the image arta e Use the mark moving keys ft gt Y or track ball to move the mark to an initial measuring point an end of long axis of ellipse f Press the SET key and then a fixed mark appears at the initial point g By using the mark moving keys or track ball the mark moves to draw an elliptical trace on the screen h When the mark is moved to a terminating measuring point the other end of long axis of ellipse length of the short axis of ellipse can be adjusted by using the N increasing M decreasing keys After adjusting size of ellipse press the SET key again and the area and circumference values of the ellipse are presented thus fulfilling elliptical measurement 1 By repeating step d h multiple measurements of circumference can be made j When pressing the END key the system will return to the original state with result record retained Pressing the CLRI key will bring the system back to the original operating state with all the result records erased k Whe
8. at the screen It can also be used for decreasing noise and light stains It is merely applied during B or B B mode image display The percentage indicated in the FC area at the lower right portion of the screen is the related value of the previous frame image and the current image Frame average can be changed over by pressing the END key in real time state 3 4 6 Image processing Image processing is to select different gray scale curves to enhance or lessen some gray scales so as to get better image for the observation and analysis The system has four gray scale curves They can be selected and displayed in the IP area at the lower right portion of the screen by pressing the IP key IP 3 represents selection of linear curves which won t intensify structure of image IP 2 represents intensification of brightness of image with high gray scale The image becomes gentle and surrounding tissue is intensified Used for diagnosis of soft tissue IP 1 means that amplitude of intensifying brightness of image with high gray scale is further increased relative to curve Used for diagnosis of soft tissue IP 0 means that middle bright gray scales are intensified to get a higher contrast As a result a clearer image is obtained for diagnosis of structure with low echoes 3 5 Zooming and depth change 3 5 1 Zooming During real time single B mode image display the control is used for switchin
9. for bovine equine ovine canine and feline Operating steps are as blow e Select B or B B mode operating state e After scanning with probe press the FREEZE key to freeze the displayed image e Press the C key to open the animal menu to select desired animal species BOV toos Bovine EQU uesoricoraaziasids Equine OVI eeen e Ovine CAN usd Canine A Feline 3 9 1 Measure bovine gestation age and EDD The system can measure bovine BPD CRL TD and automatically calculate bovine 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 22 gestation age and EDD according to measurement result Operating steps are as blow e After enter into animal menu press the direction arrow key mark moving keys gt Y to move the cursor to BOR then press SET key to select it e Press Cy key to open the reproduction measurement function and the measurement items will be displayed on the right side of the screen as below BPD piensa BPD Name of measurement item A A W for week and D for day AA Expected date of delivery SPER ii Month date e Press OB key to select other measurement item in turn e Measure the item just as measuring distance or measuring area by Ellipse method The result will be displayed at the right portion of the screen e Press CRL key to clear current measurement result and can do new measurement e Press END key to quit 3 9
10. he can save the needed images in the system and print them when he return to his clinic e Storing a permanent image Freeze a useful image Press the W key to enter the image into FLASH memory in the additional memory board Storing process will take a few seconds As soon as the image is stored the following message will appear at the upper left portion of the screen PEAS 22535235 ES FLASH memory E ni Page of image in the FLASH memory In case less than eight images are stored the system will enter the current image in sequence into the remaining page of the FLASH memory As eight images are all stored the system will replace the oldest image with a new one beginning from the first image Alternatively select a certain page and store it in the following procedure e Press the R key continuously to read image See Read image and set the FLASH memory to the position to be stored At the position the old image will be presented on the screen e Scan and freeze an image the image to be stored e Press the W key to store the image e Continue to select a position for storage and repeat steps 1 3 Otherwise next storage will begin from the next page following the selected page 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 30 e Reading image In the freezing state by pressing the R key the system can display the image formerly stored
11. limits set below and without poisonous corrosive and inflammable gas The ultrasound system should be operated preserved and transported under the following conditions Conditions no condensation no condensation Operation Preservation Transportation Parameters Temperature 5 40 C 5 40 C 30 55 C as 30 80 less than 80 less than 95 Humidity no condensation Atmospheric pressure 86kPa 106kPa 86kPa 106kPa 50kPa 106kPa 0 Caution When moved from outside the ultrasound system might be still too cold and too warm compare to the room temperature Because of the temperature difference water may condense inside the machine So before turning on the power the system should be put inside the room for a while to get adapt to the environment If the room temperature is beyond the above temperature range then adapting time need to be prolonged for 1 hour for each additional temperature difference of 2 5 C Note The ultrasound system should be used far away from the electritity generator X ray machine broadcasting station TV station computer and transmission cable to avoid interference to the image A working room with air conditioner is prefered 2 2 Power requirement The AC power plug of the ultrasound system should be a three pin plug with ground protection A two pin plug without ground protection is NOT permitted The system 600VET VETERINARY ULTRAS
12. new measurement e Press END key to quit 5 Note For method of measuring elliptical circumference refer to in 3 8 1 600 VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 25 And the gestation age and EDD should be measured after the system quit from volume measurement stats 3 10 Hospital Name and ID comment 3 10 1 Entry of hospital name and characters for comment The upper left part of the keyboard is mainly used for entering characters for comment Small English letter and character at the upper part of key can be shifted by operating the key In the state of mark the charater at the upper part of an alphanumeric key is written in the state of Le the character at the lower part of the key is given The CAPSLOCK key is used for shifting capital and small English letters representing entry of capital letter and Ea representing entry of small letter In case a mistake is made in some character press the BACKSPACE key the left character beside the cursor will be deleted The CLRI key is used for clearing the entire writing in this area e Entry of hospital name Characters HOSP at the upper portion of the screen Following the characters is the display area of name of hospital During frozen image display press the CTRL S oe 99 key and a cursor is presented after
13. the lock pin is in the same direction as the slot otherwise please turn the handle key on the plug until the pin and the slot are in the same direction Then slightly insert the plug into the socket the lock pin will into the slot and then clockwise turn the handle key on the plug to the Tight position When removing the probe firstly turn the handle key anti clockwise to the Loose position and slightly take the plug out of the socket Don t push in or pull out the plug by strength Handle key c After ensuring that the AC power provided meets the power supply requirements of the system please refer to Section 1 5 of this user manual please connect one terminal of the power cord to the power inlet socket at the rear panel of the main unit and plug the other terminal to the AC power socket of the hospital d After turning on the power switch the system enters into the normal operating state Q Caution Before connecting the plug to the hospital AC power socket please make sure that the voltage of power supply is AC 230V and the power switch of the main unit is turned off The probe must be connected or disconnected only when the system is powered off The VGA OUT socket on the rear panel of the main unit is used for connection to the external SVGA monitor Please refer to the SVGA operation manual for the details of its 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 11 installation and operation Chap
14. the appliance or faulty installation The guarantee will be invalidated if the registration number has been removed cancelled or altered Faulty appliances must be returned only to the retailer where the item was bought Any item dispatched directly to us will be refused 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 35 Chapter 6 Troubleshooting The most frequently occurred errors system messages and their possible causes and solving methods are listed below Errors amp Messages Possible Cause Solving Methods When starting the system power indicating lamp is not lit 1 Power cord might not be well connected to the electricity power socket 2 Power fuse might be already burned 1 Reconnect the power cord 2 Replace the fuse When starting the system power indicating lamp is lit but monitor is dark Improperly adjusting brightness and contrast of monitor Appropriately re adjust brightness and contrast of monitor When starting the system monitor has formulated output but no ultrasonic image appears There s a message on the screen indicating the probe is not connected Probe is not connected or not well connected Switch off power and reconnect the probe Ultrasonic image is not clear Gain is improperly set or the brightness and contrast are not well adjusted Appropriately set brightness contrast and gain Image is interfered and distort
15. 2 Measure Equine gestation age The system can measure equine vesicle length and automatically calculate equine gestation age Operating steps are as blow e After enter into animal menu press the direction arrow key mark moving keys fT gt Y to move the cursor to EQU then press SET key to select it e Press Cy key to open the reproduction measurement function and the measurement items will be displayed on the right side of the screen as below E A E Length Name of measurement item s Wrs Dis W for week and D for day e Measure the Equine Length just as measuring distance The result will be displayed at the right portion of the screen e When the measured length value is between 25mm to 26mm the following note sentence will appear in the screen 1 Within 18 to 26 days after pregnency 2 Please find more details from user manual Chapter 3 600 VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 23 3 Press the clr key to return to image More detail information is as follows 17 20 vesicle orientation 20 detection of embryo 24 detection of allantois 26 allantois 25 of vesicle 29 allantois 50 of vesicle e Press CRL key to clear current measurement result and can do new measurement e Press END key to quit 3 9 3 Measure Ovine gestation age The system can measure ovine BPD CRL TD and automatically calculate ovine gestation age and EDD ac
16. 600 VET Veterinary Ultrasound System Operating Manual INDEX Section Page A ss tauo ade dies conuteevsueavegucaseadedeasandaveadeikescenpeueveeusiseden cebevasiateets O RA A A 1 1 General description sosina n a i E E a ite 3 TA Purpose Of USC x enin ea a a tenet E eee adel ARR 3 1 2 Feat r s ria rs 3 US Main AUS E A A AE EAE EE a Bs 4 1 4 Major technical Specialties recaen imac 4 PAO PSA conditions eenen a a a a eae 6 1 6 SOCUIILY type supine a 6 Baca Us a a end 6 1 Optional exa iS A A ii asians 6 1 9 The meaning Ofinark note eles ies a Kaia delete ete 7 AA e eh ESEE TEES EES ESTEK Saa ES 8 2 Conditions A e E RG iaa St 8 2 2 Power TEQUES sai Area 8 29 A A O taal ae 9 2 A STT CUTO italia asas 9 20 DIES td da io dto adoos 9 O O e e O 10 o sisene ae etal een a N a E RREN 10 2 8 Installation usina 11 A E EN 12 A i e a es eaa Gee 12 32 Selection Of Probe Pd EA E E EA 12 3 3 Mode selections ninisi ii aed eesti 13 OS 13 A A A E A eee nas 13 A Aas oak 14 3 3 4 B M mode s cist uct pean ai eass 14 SA DERM MOW GP TNA S CZ 555122555 cas E E E E 14 3 4 1 Contrast and brightness Of image ooooonoocccnoccccnonccononcnonancnnnnncconnacinnncnnns 14 SA E Gio Gite ded oe elas A E ads hl Lady 15 A au iE Websense adminis 15 a ea T S TER 16 E A ea A a e E ER 16 3 4 0 Image proc s sN ii a EER E E ERT ee 16 3 5 Zooming and depth change ssssesessessseesseeesssesssetssessessseeessseesseessersseeesseesssees 16 Bs od
17. G MANUAL 33 e Please switch off the system unplugged the power cord and clean the outside frame of the unit E Note If the system is not be used for a long time Please connect the system to the power every three months to make sure its in good condition 4 4 Replacement of fuse 4 4 1 First please turn off the power of the system and unplug the power cord 4 4 2 Then please screw off the fuse holder on the rear panel of the main unit 4 4 3 Take out the burned fuse and replace it with a new one Fuse type should be 250V 1 6AT There re 3 back up fuses of this type in the packing box Then please screw on the cover of fuse holder tightly O Warning Please ensure the power of the system is turned off when open the fuse holder Please make sure the fuse conform to the IEC60127so as to avoid any injury and property loss 4 5 EMC electromagnetic compatibility This system is designed fully according to Class A requirements specified by the Medical Electrical Equipment EMC Regulations IEC60601 1 2 To meet the EMC requirements please install the system under the installation conditions required by this operation manual Please connect your local authorized maintenance person if there s any question or problem about EMC 4 6 Requirement of environmental protection The usage life of this system is 8 years maximum Please always dispose the system according to your local environmental protection law and regulations when it exce
18. OUND SYSTEM OPERATING MANUAL 8 should be connected to an individual hospital power source or equipment otherwise the leakage current might exceed the safty level O Warning The ultrasound system should have reliable ground connection O Warning The system must use the power cord provided by the manufacturer and cannot replace it other power cords 2 3 Preparations before installation Before installation please conduct the following necessary inspections 1 Toensure that the operation environment conforms to the environment requirements the temperature humidity clean and no strong interference source etc Especially that the power supply must conform to the requirement in particular 2 To open the packing box and check the goods against the packing list to make sure no discrepancy and no damage from outlook 3 To check the related cords and to ensure that each cord is properly connected 2 4 Structure Brightness Knob Probe gt f q y 4 y Contrast gt Knob Keyboard Track Ball f Fig 1 The Outlook of the Main Unit 2 5 The dimension of out frame Main unit 450x280x300 mm 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 9 2 6 The rear panel of the main unit AC 230V IN A AS A VIDEO OUT VGA OUT tas Es a a a D D a Fig 2 Diagram of rear panel of the main unit 2 7 Control panel Keyboard JEJE JEJEJEJE Geol 4 al ee Nano ae o aa NODO Ey AAN NR
19. a measurement e Use the mark moving keys ft gt Y or track ball to move the mark to an initial measuring point f Press the SET key and then a fixed mark appears at the initial point g By using the mark moving keys or track ball the mark moves to form a trace on the screen h When the mark is moved to a terminating measuring point press the SET key again and the dotted line between the initial point and the terminating point becomes a solid line thus forming a desired and enveloped region Meanwhile the spare lines outside the region are all automatically cleared and a contour line 1s remained Finally circumferential length or area of the region is automatically calculated and displayed at the right portion of the screen 1 Byrepeating step e h multiple measurements of circumference can be made j When pressing the END key the system will return to the original state with result record retained Pressing the CLRI key will bring the system back to the original operating state with all the result records erased k When using the FREEZE key the system will directly return to real time image 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 19 display with all the measured results cleared time operating state with all the results erased e Measurement of circumference and area elliptical method
20. aditional system with only 7 inch PAL monitor 1 3 Main functions 1 3 1 1 3 2 1 3 3 1 3 4 1 3 5 1 3 6 1 3 7 1 3 8 1 3 9 1 3 10 1 3 11 1 3 12 It supports the B B B B M M mode image displays At the time of M or B M mode image display four kinds of sweep speeds 2s 4s 6s 8s are provided It provides 4 step image magnification at x1 0 x1 2 x1 5 x2 with depth change It provides the adjustment of near field far field total gain brightness and contrast control It uses the latest techniques such as 4 stage transmitting focus 4 stage dynamic receiving focus dynamic aperture control dynamic frequency scanning etc It supports the multi frequency conversion STC quick selection and image post processing It supports image freezing and various image storage functions It supports up down left right and positive negative image reversing functions It supports the measurements of distance circumference area volume and fetal weight as well as the automatic calculation and direct presentation function including the fetal age and expected delivery date heart rate etc Both the elliptical or tracing methods are available for the measurement of area It provides 16 kinds body marks together with the corresponding probe position indication The full screen annotation animal name input are also available and the date and time is provided by a real time clock The track ball are build in the keyboa
21. cording to measurement result Operating steps are as blow e After enter into animal menu press the direction arrow key mark moving keys fT gt Y to move the cursor to OVT then press SET key to select it e Press Cy key to open the reproduction measurement function and the measurement items will be displayed on the right side of the screen as below BPD nro BPD Name of measurement item Wise Dira dig W for week and D for day EDD ana Expected date of delivery ef di diles Month date e Press OB key to select other measurement item in turn e Measure the item just as measuring distance or measuring area by Ellipse method The result will be displayed at the right portion of the screen e Press CRL key to clear current measurement result and can do new measurement e Press END key to quit 3 9 4 Measure canine gestation age and EDD The system can measure canine GS CRL HD BD and automatically calculate canine gestation age and EDD according to measurement result Operating steps are as blow 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 24 e After enter into animal menu press the direction arrow key mark moving keys fr gt 0 to move the cursor to CAN then press SET key to select it e Press Cy key to open the reproduction measurement function and the measurement items will be displayed on
22. ction Repeat steps e 1 to measure the third distance diameter from left to right D3 When the three distance values are obtained the volume value appears immediately at the right portion of the image Its unit is cm m Repeat steps a l to measure another volume value 5 Note During distance measurement press the END key to exit from distance measuring status Then press the END key again the system will exit from the volume measurement states Press CLR key and the system will exit from the measuring states and clear all the measurement records There are three volume calculating formula available as follows 1 NORMAL Volume distancel1 distance2 distance3 ID 6000000 2 Bladder Volume distancel distance2 distance3 0 5233 1000 3 Thyroid Volume distance1 distance2 distance3 0 2083 1000 3 8 2 Measurement and calculation in B M M mode operating states In B M and M mode operating states distance and heart rate can be measured Heart rate is expressed as number of heartbeats per minute In order to ensure correct measurement the initial and terminating measuring points should have the same status in heart circulation e g either at peak or in trough e Distance measurement See Measurement of distance in B B B mode operating states e Measurement of heart rate 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 21 a Obtain useful imag
23. d L74605 probe has 4 step multi frequency as 3 5 5 0 6 0 7 0MHz 3 2 probe connectors to allow simultaneous connection of 2 probes at the same time and the connected probes can be selected from the keyboard 4 Cine memory card to allow the permanent image storage of 8 frames Max and the record amp back play of 64 frames Max 5 Video recording unit suggest to use Sony UP 895MD printer or Mitsubishi P91 printer 6 14 inch SVGA monitor can be connected directly to the main unit to display larger images at the same time Q Caution Please choose the printers acknowledged by the manufacturer otherwise it may cause damage to the system Please refer to the operation manual of the printer for the installation and operation details 1 9 The Meaning of Mark Note A Please read the operating manual Warning Y High voltage S Protective earth terminal Security type O 4 O Signal grounded Potential equalization conductor terminal Signal output Brightness of monitor Contrast of monitor Main unit power off Main unit power on 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 7 Chapter 2 Installation 2 1 Installation conditions The ultrasound system should be working in an environment without strong magnetic field interference and free of strong electric interference from the electricity network The room should be well ventilated clean dark and have stable temperature within the
24. e b Press the FREEZE key to freeze the image c Press the MEAS key and measurement of heart rate is selected d Press the SET key and then a corresponding small mark appears in the image area e Use the mark moving keys or track ball to move the mark to an initial point of a target to be measured f Press the SET key and then a fixed mark appears at the initial point g By using the mark moving keys or track ball the mark moves to a point which is at the same status as the initial point with a heart circulation apart h Press the SET key and the mark is fixed at the terminating point Thereby a heart rate is presented at the right portion of the screen When the interval between the initial point and the terminating point is two heart cycles the actual heart rate should be the indicated rate x2 and on the analogy of this i By repeating step e h multiple measurements of heart rate can be made j When pressing the END key the system will return to the original state with the result record retained Pressing the CLR key will bring the system back to the original operating state with all the result records erased k When using the FREEZE key the system will directly return to real time image display with all the measured results cleared 3 9 Reproduction measurement for animal gestation age and EDD The system can do reproduction measurement
25. e and wide band low noise preamplifiers logarithmic compression etc 1 2 4 It has very abundant display and measurement features including image freezing function measurements of distance circumference area volume normal bladder volume thyroid volume etc It also has multi mode display zooming function with depth change image reversions functions for the image processing It provides up to 5 kinds of animal reproduction software covering bovine ovine equine canine and feline And veterinarians comment animal name and real time clock setting can be 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 3 1 2 5 1 2 6 1 2 7 displayed in image area By using a track ball various measurements can be performed conveniently and flexibly Moreover by adopting special high integration devices and high speed CMOS ICs 600VET delivers more useful features with much better reliability than a tradition ultrasound scanner but at a lower power consumption The design of all plastic case covered with plastic diaphragm large monitor with fold up keyboard gives it a beautiful and modern outlook The unit is equiped with a large 10 inch high resolution rectangular black white SVGA monitor which provide flashing free high quality images by adopting the unique continuous line to line scanning method With large and stable images operators will not easily feel eye fatigue during long time examination as they used to be when using a tr
26. e the appropriate adjustment according to requirement of diagnosis Brightness control The brightness can be adjusted with the knob below the lt mark at the right part of monitor It will be brightened by clockwise turning the knob or vice versa Brightness should be adjusted in association with the contrast the contrast will decrease if the brightness is set too high while the gradation will decrease if the brightness is set too low Please appropriately adjust the contrast in association with brightness according to actual need and the working environment Suggestion Normally it s suggested to set the contrast and brightness to the extent that the lower gray scale area at the lower left portion of screen is well displayed In that setting a clear image with good gradation will be displayed 3 4 2 Gain control Total gain Two touch keys of GAIN are provided for adjusting overall ultrasonic echo receiving sensitivity to obtain a satisfactory image display Its adjusting range is 0 99 Near gain Two Tr Y touch keys of NEAR are provided for adjusting near field receiving sensitivity of ultrasonic echoes to obtain an optimum near field image display Its adjusting rangeis 30 0 Far gain Two Tf Y touch keys of FAR are provided for adjusting far field receiving sensitivity of ultrasonic echoes to obtain a c
27. ed or its lower portion in the far field is not clear There are electric motors ultrasonic nebulizers cars computers radio sets and other interference sources nearby power supply is not grounded or is unstable Move or keep away from interference source Use a separate 230V 10 power supply The grounding terminal at the rear of main unit is well grounded The gray scale is S twisted in the image area Power supply voltage is too low Adjust supply voltage or use a voltage stabilizer If you need some help please contact our authorized agent in your country or contact us directly at the following address Company name GIMA spa Address Via Monza 102 Gessate MI Italia Post code 20060 Tel 39 02 953854209 Fax 39 02 95380056 E mail export gimaitaly com 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 36
28. eds the usage life or if you want to dispose it before the system reach its usage life 4 7 Precision measurement Please invite your local gage authority to measure and gage the system annually and record the results If the precision situation is not qualified please stop using the system immediately and contact your local authorized service people 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 34 Chapter 5 Warranty Thank you for having acquired our product This product meets the most stringent requirements regarding the selection of quality manufacturing materials and also the final control The product has a 12 month warranty valid from the date it is delivered by GIMA During the guarantee period free repair and or replacement of any defective parts due to faulty manufacture will be given labour postal transport and packaging charges etc are not included The guarantee therefore excludes components subject to wear and tear such as parts in rubber or PVC doppler probes SpO2 sensors lamps batteries electrodes handpieces washers and packings resistances etc No compensation will be given for loss of use of the product Furthermore replacement or repairs effected during the guarantee period do not lengthen the duration of the guarantee This guarantee is void in the event of repairs effected by unauthorised persons or with spare parts not approved by GIMA damage or defects caused by negligence blows abnormal use of
29. g magnifications of x1 0 x1 2 x1 5 and x2 0 to obtain a definite image display and a best measurement result 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 16 3 5 2 Depth of image During real time image display when an image of x1 2 x1 5 or x2 0 magnification 1s taken it is necessary to use the DEPTH key to vertically move an image on the screen to different depth accordingly Depth of image is indicated by graduations at the right portion of the image with 1 cm each graduation 3 6 Image control 3 6 1 Image freezing During real time image display by operating the FREEZE key the displaying image can be turned into the frozen image When pressing the FREEZE key again the original real time image is reset 3 6 2 Selection of scanning direction The NEG key is used for reversing scanning direction of probe during real time image display When the key is pressed the displayed image is turned over in the right left direction The scanning direction arrow in the character area at the right portion of the screen is reversed at the same time 3 6 3 Image reversing During frozen image display by pressing the NEG key the displayed image can be changed from negative to positive black to white for making slides for study First press the CTRL key then press the INEG the image will change from up to down 3 6 4 Focus selection e
30. he probe tip must not be soaked in a solution Simply clean it using a soft cloth moistened with alcohol and then dry it 4 2 6 Disinfection and sterilization Please sterilize the probe surface by using the special alcohol cotton pads everyday both before and after using the probe Please use soft cloth to apply the special 75 medical alcohol solution to clean the probe carefully The steaming heating and other sterilization methods are prohibited 4 2 7 Please strictly keep the probe away from the paint thinner ethylene oxide other organic solvent etc 4 2 8 Please keep the probe inside the metal probe case when it is not in use 4 2 9 Dipping the probe or the cable into any liquid is strongly prohibited Warning Please immediately stop using the probe and system if there is any broken on the electricity cable or the probe Otherwise there will be a danger of the electricity shock 4 3 Maintenance Please conduct the regular maintenance of the system Daily maintenance e Please use wet soft cloth to remove the ultrasonic gel from the probe and clean it tenderly after each usage e Please check if the probe and electricity cable is broken or torn out e Please sterilize the probe both before and after the usage Weekly maintenance e Please check if the probe is in good condition e Please check if the electricity cord is in good condition e Please sterilize the probe when necessary 600VET VETERINARY ULTRASOUND SYSTEM OPERATIN
31. ill be cleared The system will automatically enter into the memory functional state Chapter 4 Maintenance 4 1 Main unit 4 1 1 The proper operation environment must be provided The ultrasound system must be kept clean 4 1 2 Please wait for at least 1 minute before restarting the system after switching off 4 1 3 The keyboard surface need to be maintained carefully Please press the keyboard tenderly to avoid scratching or damages 4 1 4 Please use soft wet cloth to clean the out frame of the unit If it is too dirty and still unable to clean please use the soft wet cloth to dip the special non corrosive detergent to clean it Please avoid any liquid splashing into the unit 4 1 5 Do not use any glass detergent which contains hydrocarbon to clean the monitor screen 4 2 Probe 4 2 1 Please take good care of the probe Collision and droping is strongly prohibited 4 2 2 Please use the ultrasound gel which is acknowledged by the manufacture of the unit 4 2 3 Plug and unplug of probe in real time is strongly prohibited 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 32 4 2 4 Bending and pulling the probe or the probe cable by strength is prohibited 4 2 5 Washing probe Probe tip IA Rinse the surface with running water Washing with water Wash out blood and mucus contaminating the insertion port of the probe or the area around it using a sponge or soft cloth Connector Cable other part of t
32. in the permanent FLASH memory on the screen The page No of the displayed image 1 8 in the FLASH memory will also be indicated at the upper left portion of the screen E Note When pressing the R key in the freezing state a If there are images in single image memory all the stored images will be cleared b If the system is in the state of cine memory it will be converted to the permanent FLASH memory state and it will erase all the images stored in the temporary single image memory 3 15 3 Cine memory Function record amp back play of 64 frames Max During real time image display B mode images can be stored by one frame after another into the image memory in time sequence If the cine reproducer memory is full of images at the same time of storing the newest frame of image the oldest stored image should be moved out of the cine memory memory So the cine reducer always keeps 64 latest images among which the 64 frame is the latest image The stored images after being frozen can be manually played back or automatically reproduced cyclically e Image acquisition During B mode defrozen single image display by pressing the storage key If the system is not in the state of cine memory functional mode the system enters into image acquisition process The prompting message at the upper left portion of the screen is changed from MEMORY to CINE accordingly At that time the current scanning images are st
33. ing amp electronics It is a linear and convex array electronic scanning system with a 3 5 MHz R60 convex array probe multifrequency as the standard configuration and the 5 0MHz linear array rectal probe multifrequency and the 5 0MHz R20 convex probe as options multifrequenc y The system can be used for examination and diagnosis of small aninmal and big animal in abdominal reproduction small parts urology cardiology tendon etc Before operating this ultrasound system please make sure the operator has read this operation manual carefully and can thus operate system correctly to make 1t work according to its specified safety standard and reach its performance standard 1 2 Features 1 2 1 The 3 5 MHz R60 80 element convex array probe called C60 probe is used as a standard configuration of the system Other probes can be selected according to veterinary needs 1 2 2 It has 4 step multi frequency conversion function for all the probes to allow the veterinarian to tailor the frequency to different animal body size It also have 8 STC curves and 4 image processings IPs available for choice 1 2 3 The images displayed by the system are crystal clear stable and with high resolution due to adopting the latest techniques such as continuously variable aperture automatic multi stage focussing TGC dynamic filtering image edge enhancement frame correlation linear interpolation 256 gray scales image display wide dynamic rang
34. le operation is finished In case that there is no need for indicating ZN position and direction of probe after selection of body mark press the I A key to end the operation 3 11 Record The standard configuration of the system doesn t have the picture record However the manufacture can supply upon customer needs Sony UP 895MD printer must conform to standard IEC60601 1 Please connect the video recorder to the video out socket on the rear panel of the main unit Please read the user manual of picture record and connect the printer When taking down the notes please use the picture record according to its own user manual O Caution All the video equipment that is connected to ultrasonic system must conform to standard IEC6060 1 and the grounded connector should be grounded on the external frame 3 12 Setting of real time clock 600 VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 27 The built in real time clock with date is provided with ready cell for ensuring operation in the power off condition Its accuracy is 1min month Date and time can be set during frozen image display in the following procedure Press the MENU key and use the moving key or the alphanumeric key 4 to select DATE at the lower part of the screen Press the SET key and a whitened year appears at the upper right portion of the screen Use the or key to increase
35. lear far field image display Its range is 0 30 The system offers eight STC curves for user to select During real time B mode image display press the SHIFT and the eight STC curves are displayed in turn in the middle of character area at the right portion of the screen When the END key is pressed the system will exit from selection of STC curve 3 4 3 Four frequencies Each probe is capable of scanning at four different frequencies Low frequencies are suitable for fatter patients and high frequencies for thinner patients The frequencies can be changed over by using the FREQ key Real time scanning frequency is shown in the FR area at the lower right portion of the screen 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 15 3 4 4 Linear averaging Linear averaging is to control smoothness of image and decrease image noise by taking percentage of previous and present picture elements pixel at the same specified beam Linear averaging is merely applied in B or B B mode operation The percentage indicated in the LC area at the lower right portion of the screen is the related value of the previous pixel chosen and the current pixel Linear average can be changed over by pressing the SET key in real time state Linear average 0 or 25 is recommended for use 3 4 5 Frame averaging Frame averaging is to control smoothness of image by taking percentage of previous and present frame images specified
36. ment 230V AC 10 50Hz 1Hz grounded Because of the instability of the local electricity voltage at some areas a power supply stablizer is recommended to be used to protect the system and to ensure the steady image display The system should be placed in a well ventilated dry environment and kept away from strong electromagnetic interference poisonous and corrosive gas Direct exposure to sunlight and rain should be avoided 2 6 Security type Anti electrical shock type Class I equipment This means the equipment not only has the basic insulation but also has the grounded to provide protection against the electrical shock Level of anti shock Type BF equipment This means the equipment is the Type B equipment equipped with the Type F applied parts Type B equipment This means the equipment can provide the protection against the electrical shock to certain level if the equipment is within the permissive current leakage limit 1 7 Packing list Main unit 1 set 3 5 MHz convex array probe C60 probe 1 pe Probe holder 1 pe Aluminum hand carry case for probe 1 pe Power cord 1 pe Ultrasonic gel 1 bottle Operating manual 1 copy Warranty card 1 copy QC Pass 1 copy 1 8 Optional parts available 1 5 0MHz micro convex probe Radius 20mm 80elements called C20605 probe has 4 step multi frequency as 3 5 5 0 6 0 7 0MHz 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 6 2 5 0MHz linear rectal probe 80 elements calle
37. n using the FREEZE key the system will directly return to real time image display with all the measured results cleared e Volume measurement three axis method Obtain useful image b Press the FREEZE key to freeze the image c Press the IMENU key and use the direction keys gt 2 or alphanumeric key 2 to select VOL at the lower portion of the screen d Use the direction keys gt to select desired volume formula Press ISET key to select it e Press SET key again and a corresponding small mark appears in image area 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 20 f Use the direction keys gt lt a or track ball to move the cursor to measurement start point g Press the SET key to fix the start point h Press the direction keys f gt or turn the track ball to move the cursor to the measurement end point there will be a dotted line between the start point and end point 1 Press the SET key to fix the end point At the same time the first distance value diameter from top to bottom D1 will be displayed near the terminating point j By repeating step e i the second distance diameter from front to back D2 is measured k Acquire the second image cross se
38. ng to the parameters of the 3 5MHz convex array probe The 2 probe connectors will allow simultaneous connection of 2 probes and each probe connected can be easily chosen by pressing the numerical key Mm The name of the probe chosen will be displayed at the right bottom area of the screen O Warning It is strictly prohibited to use any probe other than the probes provided by the manufacturer otherwise the system and probe may be damaged The manufacturer will not be held responsible for any damage arising from such misapplication and 1t s also not covered by our warranty terms A 2 probe Connector When order the 2 probe connector the second connector has a cover on it for safety reason Please remove the cover ONLY when you connect 2 probes simultaneously If only 1 probe is connected please put back the cover on the unused connector for safety A Unplug the probe Please switch off the power of the main unit before connecting and removing the probe s 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 12 3 3 Mode selection 600VET has four scanning modes B B B B M and M Scanning modes can be changed only during the real time image display A description of all the scanning modes for this convex array probe is given below 3 3 1 B mode e B mode is the basic operating mode for the two dimensional scanning When the system is powered on it will automatically enter into the B mode freezing state At that time by
39. of the heart beating area in the B mode image region a corresponding M mode image will be presented in the M mode image region In the real time state by pressing the B M key the B M mode image display can be obtained The B M key can be used to select sweep speed The system has four sweep speeds 2s 4s 6s 8s available for selection The selected sweep speed is shown below the scanning direction arrow at the right portion of the screen For example TM 2s By pressing the FREEZE key the displayed image is frozen When the system is in the real time state press any mode key except the B M key it will exist from the B M mode 3 4 Definition of image 3 4 1 Contrast and brightness of image The contrast and brightness of monitor is one of important factors which will determine the image quality The operator should make the adjustment of the contrast and brightness according to its actual surrounding environment e Contrast control The black and white contrast of can be adjusted by turning the knob below the mark 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 14 at the right part of monitor the contrast will get stronger by clockwise turning the knob or vice versa Normally sharp contrast will enhance the edge of image and lower contrast will be good for the analysis of the targeted object s nature as it enhances the gradation of the image Operator should mak
40. or decrease the year correspondingly After year setting use the gt or key to move the cursor rightward or leftward to month date hour minute and second to be set and make an alteration with the or U key After time setting is done use the END key to return to the original state 3 13 Selection of beam sampling puncture guide When puncture guide is selected the operator can move the probe to an appropriate position with puncture guideline aiming at an ideal piecing point When the H key is pressed during real time image display beam sampling line will be displayed or shielded The sampling line can be moved by using the gt or key or track ball 3 14 Function of green environment protection In order to fully protect ecological environment the manufacturer has adopted the up to date artificial intelligence technique in the present trend of developing green products 600VET is kept monitoring during operation In case that the trackball or any key is not operated beyond a certain period Setting time is about 15 minutes the displayed image will be automatically frozen and the system gets slept Under that condition if the system need be restarted only by pressing any key or turning the trackball the original operating state will be recovered 3 15 Usage of cine memory card optional With the cine memor
41. ored the old stored image will be cleared or correspondingly replaced by a new stored one 3 7 2 Storing e If there is an image worthy of storage use the FREEZE key to freeze the image e Press the El key to store the image e Press the FREEZE key and the normal image is recovered e Press the FREEZE key to freeze the image e Press the El key to recall the stored image for comparison e Press the FREEZE key to recover scanning E Note When additional functional board is fitted storage of single image refers to 3 15 Cine reproducer card 3 8 Measurement and calculation The system is capable of measuring distance circumference area heart rate and volume during image freezing as well as automatic calculation and presentation of the measured result on the screen 5 Note During measurement the H key can be used to activate or stop the cursor fast moving function 3 8 1 Measurement and calculation in B B B mode operating states In case of B or B B mode image display distance circumference and area can be measured e Distance measurement Obtain valuable image a b Press the FREEZE key to freeze the image gt Press the MEAS key to select distance measurement gt Press the SET key and a corresponding small mark appears in image area e Use
42. ored into the 64 image cine memory in real time sequence By pressing the freezing key the system stops image storage e Manual playback When image is frozen the system enters into the manual playback operating state default By operating trackball or the fast moving keys lt gt the images stored in the image memory can be observed one by one Current frame No will be indicated at the upper left portion of image area as below CINE oerda eaa Pe rey ONE era Current status is cine reproducing 2 at Current frame No 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 31 Automatic reproduction During manual playback by pressing the P key the system enters into automatic reproduction state At that time image can be played back in a rising order When the P key is pressed again the system will exit from the automatic reproduction state Withdrawal from cine reproduction During image freezing by pressing the CTRL C keys in turn the system can exit from the cine reproducer functional mode and enter the memory functional mode Note In the image freezing state the CTRL C keys can be used to change over from the cine memory functional mode to the memory functional mode If there are images in the cine memory e When probe or magnification is changed images stored in cine memory memory and single image memory w
43. ozen status press body mark key A to select animal body mark When the key is pressed a small graphic body mark ws appears at the right portion of the screen character area and indicates that the system enters into functioning states of body mark selection and probe mark rotation At that time 16 body marks are shown for selection in the image area At the upper left part of the image there is a gt cursor Use the body mark moving key or track ball to move the cursor gt to a desired body mark Then press the body mark y key again to select it At the same time the 16 body marks graph disappears and the selected body mark is displayed at the lower left portion of the screen Here attention should be paid to the fact that when a body ao mark has been selected the graphic body mark XA still exists at the right portion of the screen and indicates the position of probe Meanwhile a small arrow indicating probe position is shown in the body marks graph at the lower left portion of the screen By operating the probe mark rotation key or track ball it is allowed to move to a corresponding position according to actual position of the probe When the arrow is located at a desired position it can be turned anti clockwise by using the N key a clockwise by the 14 key to match with direction of probe When pressing the A key again the who
44. pressing the FREEZE key the probe starts real time scanning Press the FREEZE key again and the image displayed will be frozen When the system is in the real time state press the B B jor B M or M mode function key and the system will exit from B mode to the pressed mode 20 21 22 23 24 HO y aa E nin dat 1 Year month date minute OSPGWIUMXI Va i 2 Total gair 0 99 k f s 3Near gain 30 0 4F ar gain 0 30 10 48 L z 5 Focus indication Qa 64 6 Display mode and magnification S i 5 7Scanning direction 2 8Measurementtype or body mark QMeasured value E 7 10 Probe type 11 Conversion frequency EN 12 Line correlation ee 13 Frame correlation Pat 14 Post processing 10 15 Depth scale YU 16 Prompting freezing state s sM e 17 Body mark MAL 18 Probe position Fos a 19 Patients name r E 20 Grayscale Ala 21 Comment in image area E 15 22 Hospital name a 16 23 Image 24 Horizontal scale Fig 4 Meaning of the display and characters on the screen 3 3 2 B B mode In the B B mode double image display is available When the B B mode switching key is pressed choice can be made between the live and frozen images displayed on the screen In the real time state when pressing the B B mode key the right and left image displays will exchange their status 1 e the original live image will be frozen while the other image i
45. rd to allow easy and flexible measurement and operation Standard PAL system video signal output and VGA signal output 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 4 1 4 Major technical specifications Probe Standard probe 3 5 MHz R60 80 element convex array probe is the standard configuration called C60 probe It has 4 step multi frequency as 2 5 3 5 4 0 5 0Mhz different frequencies can be selected from the keyboard This is mainly for the abdorminal reproduction Urology examination etc Two optional probes are also available 5 0MHz micro convex probe Radius 20mm 80elements called C20605 probe has 4 step multi frequency as 3 5 5 0 6 0 7 0MHz 5 0MHz linear rectal probe 80 elements called L74605 probe has 4 step multi frequency as 3 5 5 0 6 0 7 0MHz Scanning depth 220mm depend on the probe types Monitor The unit is equiped with a build in 10 inch high resolution rectangular black white SVGA monitor which provide flashing free high quality images by using the unique continuouse line to line scanning method Gray scale 256 Error of geometric position lt 5 Power supply 230V AC 10 50Hz 1Hz grounded Power consumption Not greater than 100VA MTBF Designed value is larger than 3000 hours 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 1 5 Operating conditions Ambient temperature 5 40 C Relative humidity 30 80 RH Atmospheric pressure 86 106 KPa Power require
46. s activated At that time a mark will appear under the two arrows at the right portion of the screen and it will point at the current active image When pressing FREEZE key again the current image will be frozen or defrozen In the real time state 600 VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 13 press the B or BB M or M mode key and the system will exit the B B mode to the pressed mode 3 3 3 M mode e The M mode image reflects the movement of all the points on the sampling line of the targeted examination area The M mode image display will vary with time so it is suitable for the cardic examination e In the real time state of B or B M mode when pressing the H key a vertical dotted line 1 e sampling line will appear The line can be moved to the targeted position during M mode by pressing the gt and the lt fast moving keys When the M key is pressed M mode image is displayed The current sweeping speed can be selected with the M key there re 4 step of sweeping speeds available for choice 2s 4s 6s 8s e When the system is in the real time state press any mode key except the IM key the M mode image display will be ceased 3 3 4 B M mode e In the B M mode both B mode and M mode image displays can be provided simultaneously By placing the beam sampling line at position
47. ter 3 Operation 3 1 Power switch After making sure that the system is connected to the proper external AC power supply please turn on the power switch of the system The power switch is located at the lower right part of the monitor When pushing it to the On or I side the system is powered on and will start working and the power indicator on the keyboard will be lit It will be contrary when the switch is pressed to the Off or O side 5 Note To ensure a long time stable and reliable operation the system can t be switched on immediately after being powered off Please kindly wait for at least 1 minute before restarting it O Warning Please do not place any liquid on or around the main unit Once spilled the liquid will reach the electrified parts of the system and increase the possibility of electricity shock 3 2 Selection of probe types Model 600VET has a single probe connector socket as a standard configuration but the 2 probe connectors sockets are also available as an option and recommended to use when the user buy 2 or 3 probes together The system can automatically recognize the probe s once the probes are connected to the system Each time the system is switched on 1t will automatically search for the probe and recognize the current probe type In case no probe is detected a corresponding message will be displayed on the screen and all the parameters will be set as default parameters correspondi
48. the mark moving keys ft gt 2 or track ball to move the mark to 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 18 an initial measuring point f Press the SET key and then a mark is fixed at the initial point g By using the mark moving keys or track ball the mark is moved and a rubber band like line appears between the moving cursor and the fixed mark h When the cursor is moved to a terminating point press the SET key and a fixed mark appears at the point At the same time a measured result is presented nearby and the value will be shown at the right portion of the screen as well 1 Byrepeating steps e h multiple measurements can be made j Press the END key and then the system will exit from measuring state with records retained Use the CLR key and the system will not only exit from measuring state but also clear all the records k Use the FREEZE key to exit from the measuring state and return to real time operating state with all the results erased e Measurement of circumference and area tracing method Obtain useful image a b Press the FREEZE key to freeze the image Press the MEAS key to select type of measurement gt Press the SET key and then a corresponding small mark appears in the image area for circumference measurement and for are
49. the right side of the screen as below riada GS Name of measurement item Wo Discos W for week and D for day FOD Eu ae Expected date of delivery KP EE E Month date e Press OB key to select other measurement item in turn e Measure the item just as measuring distance or measuring area by Ellipse method The result will be displayed at the right portion of the screen e Press CRL key to clear current measurement result and can do new measurement e Press END key to quit 3 9 5 Measure feline gestation age The system can measure feline HD BD and automatically calculate feline gestation age and EDD according to measurement result Operating steps are as blow e After enter into animal menu press the direction arrow key mark moving keys t gt 0 to move the cursor to FEL then press SET key to select it e Press Cy key to open the reproduction measurement function and the measurement items will be displayed on the right side of the screen as below A ehicate HD Name of measurement item Wa o Deisccinnicar rre W for week and D for day POD users toretrn Expected date of delivery a ia Month date e Press OB key to select other measurement item in turn e Measure the item just as measuring distance or measuring area by Ellipse method The result will be displayed at the right portion of the screen e Press CRL key to clear current measurement result and can do
50. y card user can store and back play the most up to date continuous 64 frames this will allow the operator to select the best frame he like to save and thus he will never miss the best frames that he need Besides it can also allow the permanent storage of 8 frames Max called FLASH memory which will remain in the system even the system is powered off This will 600VET VETERINARY ULTRASOUND SYSTEM OPERATING MANUAL 28 allow the operator to save important and typical frames for future comparison and measurements And with this permanent storage function the doctor don t need to bring a printer when go for out door checks as he can save the needed images in the system and print them when he return to his clinic In this case the system divides all the memories and original memory into three regions Single temporary image memory 4 frames FLASH permanent memory 8 images Cine memory 64 frames These 3 functions will be explained in details in 3 15 1 3 15 3 5 Note The cine memory card should only be assembled or disassembled by the operators trained by the manufacturer The operator shouldn t do it by himself 3 15 1 Single temporary image memory Max 4 frames When the cine memory card is fitted as soon as the system is powered on a mode prompting message appears at the upper left portion of the screen MEMORY memory functional mode in the state that power on is confirmed Ol
Download Pdf Manuals
Related Search