GS-KBC6 USER MANUAL
Contents
1. 5 IV Setting of the Keyboard 5 gt 4 1 Setup of the Protocol and the Default Baud Rate 5 gt 4 2 Setup of the Baud Rate of Communication 6 V Operation of the Keyboard 6 VI Installation and Connection 8 VII Technical Specifications 9 VIII Points for Attention 10 Summary The keyboard controller is used for terminal receivers such as the intelligent speed dome and the decoder etc Taking the EIA RS 485 electrical interface between the keyboard and the receiver one keyboard can control as much as 32 speed dome and decoders without driving the bus and the maximum communication distance between the keyboard and the receiver is up to 1 2 km It is very easy for operating and setting the speed dome camera The controller is also to control the terminal receiver to achieve the function of controlling pan tilt lens and etc Main Functions Il HI Set the address range of the dome camera and the decoder 0 255 To directly control full functions of speed dome camera For example turn ON OFF camera BLC To operate the pan tilt of speed2. 2 Video OUT Video OUT Six inches dome 1 Video OUT Video IN Multiplexer 1 Multiplexer 2 RS232 OUT RS232 OUT Six inches dome N R5485 OUT Address box Address box ID CODE 1 la 2 TONEXTBOX RS485 OUT RS485 IN RS485 OUT R5435 IN Figure 7 Figure 8 VI Technical Specifications Communication between Speed Dome Camera and Controller Port to multi port and half duplex function Communication connector RS 485 Baud Rate of Communication Four baud rates i e 2400bps 4800bps 9600bps and 19200bps Distance of Communication 1200m in maximum Power Supply DC12V 1A Size 315 X 165 X 57 mm Weight 2Kg Number of controlled speed dome camera up to 32 9999 9 VII Points for Attention Please read the operation manual of the keyboard carefully before using it The operation manual is mainly focused on all functions of PELCO D PELCO P and COP 2 Protocols For other different protocols operations could be something different and those different parts will be listed on Supplementary Description of the Keyboard Controller in details The keyboard takes DC12V power supply Please confirm the voltage and polarity before the power supply is switched on Do not place the keyboard under the rain or on wet place so as to avoid short circuit or electrical shock As the keyboard is a sophisticated electronic device you should never open the case so as to avoid the occurr
3. PELCO P 9600 om oe on DER OFF ON PANASONIC ON OFF ON OFF OFF ON Reserved OFF ON ON OFF OFF ON HUNDA600 ON ON ON OFF OFF ON LILIN OFF OFF OFF ON OFF ON Reserved ON OFF OFF ON ON OFF Reserved OFF ON OFF ON OFF ON KALATEL ON ON OFF ON ON OFF Reserved OFF OFF ON ON OFF ON Reserved ON OFF ON ON OFF ON COP 1 OFF ON ON ON OFF ON Ultrak ON ON ON ON OFF ON b DIPS and DIP6 are used to select the baud rate shown as following table DIP7 and DIP8 are not used Baud Status of ID CODE Rate DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8 2400bps OFF OFF 4800bps ON OFF 9600bps OFF ON 19200bps ON ON c Some of the ID CODE of the protocols are set as follows i 8 COP 2 9600Bps x i PELCO D 2400Bps g ON 1 oCm PELCO P 4800Bps C NCE wom AC om SOC C SC ON racov ononm SAHARA ER d Switching control between speed ia a Gee The controller can be operated in two modes Speed Dome and Multiplexer When power supply is on it is operated on the default mode namely the Speed Dome Press F3 to make switch between two modes When it is under the mode of the Multiplexer you can control it via Address Box At this time the LCD will display Mulx Addr 001 Alternatively you can control it by pressing F3 down until the LCD displays CONTROLLING MULX then control the multiplexer by the RS 232 output of the
4. dome camera moving in different speed level To set up 128 preset positions and 6 cruising tracks for speed dome camera and call any of them Each cruising track contains up to 16 preset positions You can set up the staying period and moving speed for each preset position To control speed dome camera by manual auto operation It is possible to change the initial set through setting the speed dome camera menu Manually control the focus zoom and iris of the camera Introduction of Functions Select Camera 0 255 Joystick Control Control Pan Tilt direction and speed of the Speed Dome Lens Control Control the focus zoom and iris of the camera Operation of Preset Position 1 128 Set Preset Position Call Preset Position Operation of Cruise Track 1 6 Set Cruise Track Run Cruise Track Auto Pan Control of Speed Dome including speed and direction of Auto Pan Self Learning Track of Intelligent Speed Dome Function Setting of Menu of Speed Dome Control of Multiplexer Direct Control on Decoder Control front devices such as the decoder etc Introduction of the Keyboard Panel 1 The Sketch of the Front Panel and Description of Buttons Figure 1 There are speed joystick buttons and LCD on the front panel of the control keyboard The display is used to show the status of
5. keyboard The RS 485 output of the keyboard cannot be used to control the multiplexer When operation please pay attention to the information on the LCD V Operation of the Keyboard 1 Select Address of the Speed Dome Camera CAM N Enter Display Current CamID 001 Description N No of camera from 0 to 255 Function Select the address of the camera to be controlled When the value N is in conformity with the address of the Speed Dome Camera it will be under control 2 Set the Preset Position PRESET N Enter Display Preset No 001 Description N No of preset position from 1 to 128 Function Store current position and refer it as No N position Notice Preset point set is using joystick before choice that need find a view bound 3 Call the Preset Position CALL N Enter Display Call Number 001 Description N No of preset position from 1 to 128 Function Transfer the camera to the position of No N preset position 4 Cancel the Preset Position PRESET N OFF Display Preset No 001 Description N No of preset position from 1 to 128 Function Delete the No N preset position stored 5 Set the Cruise Track COP 2 PELCO D PELCO P Available Enter the Status of Track Setting SHOT N ON N No of track from 1 to 6 Display Track 01 Sum 06 Description Track No 1 is currently setting in w
6. pan tilt is decided by the y angle of the joystick you operated Figure 3 DOWN SLOW Oy Change the tilting angle of the joystick you can Ss FAST S fe Ey adjust the speed evenly and the camera can be 7 Figure 3 focused automatically in the course of scan to keep images being distinct 16 In case error operation occurs normal display will be 7 p gt recovered after Error Operation appears for 1 second VI Installation and Connection Attention Please read the operation manual of the keyboard and the speed dome carefully before connecting wires Any incorrect connections can cause permanent damage of the device When connecting wires first switch off the power supply of all devices The communication wires between devices should be shielded twisted cable When installing cables they should be far away from high voltage lines or other possible interference circuits as can as possible 1 The marking of wires of the transfer box Figure 4 RED a GREEN 2 Connections of the keyboard controller controlling multiple speed dome BLACK YELLOW cameras Figure 5 3 Connections between the keyboard and the speed dome camera Figure 6 me ae Connection Drawing between the keyboard and the multiplexer via the GREEN GND address box Figure 7 YELLOW RS232 OUT 5 System Connection Drawing between the keyboard and the dome camera Figure 4 and the multiplexer Figure 8 Video OUT Video IN Monitor 1 Monitor
7. the system as well as operation information The joystick controls the upward downward leftward and rightward speed motion of the speed dome The description of buttons is as follows 3 CALL PRESET SHOT ON OFF CurrentC am D 001 LIVE TAPE WIDE TELE FAR NEAR N CAM ID AUTO OPEN CLOSE N PTZ amp Multiplexer Figure 1 Func 1 cam Set special function of the system together with other buttons Zoom Fullscreen Show picture of the camera in full screen Press Zoom again to review a 2 Zoom of the selected camera PIP up arrow Show picture of the camera in PIP mode Picture in Picture 2X2 down arrow Show picture of the camera in 4 frame 3X3 left arrow Show picture of the camera in 9 frame 4X4 right arrow Show picture of the camera in 16 frame Live Show live picture of the camera at current mode Tape Playback pictures Function Tape Playback video information of VCR CAM in multiplexer mode Used with camera buttons to select cameras to display in the full PIP 22 3 X3 4 lt 4 formats in speed dome mode Select address of the intelligent speed dome F2 in multiplexer mode Start automatic switching of cameras This button is also used during setup to turn on all motion detection targets in speed dome mode Auxiliary control but
8. FULL FUNCTION KEYBOARD CONTROLLER GS KBC6 USER MANUAL GOLDEN STATE INSTRUMENT CO 14256 Doolittle Drive San Leandro CA 94577 510 352 7860 Fax 510 352 5988 Email gsi goldenstateinst com Website www goldenstateinst com 1 800 227 2330 SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO DOT OPEN COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lighting flash with a arrowhead symbol in an equilateral triangle is intended to alert the user There is uninsulated dangerous voltage presence near by the product s enclosure which may be risk of to persons triangle is intended to alert the user to reference of the important operating and maintenance servicing instructions l The exclamation point within an equilateral THE PRODUCT CODE MARKED ON THE BOTTOM COVER PLEASE FILL THE CODE IN THE FOLLOWING BLANK PLEASE SAVING THIS SPECIFICATION CAREFULLY SO THAT CHECKING MODEL PRODUCT CODE INDEX I Summary 9 2 22 22 0 22 2222 n nnn nn nn 2 II Introduction of Functions 3 IH Introduction of the Keyboard Panel 3 gt The Sketch of the Front Panel and Description of Buttons 3 gt Rear Panel
9. ence of trouble The keyboard has integrated multiple protocols and you are pleased to select correct protocol and the baud rate When switching on power supply take care of the selected protocol and the baud rate on the first screen In case the keyboard controls the multiplexer the operation of combination buttons is as follows Press one button first and press the other button after release the first one For example When enter exit setting of the menu Function Zoom press Function button first and press Zoom button after Function button is released While use Func alone please put it down until Motion Detect OK appears When control the multiplexer through adapter box select the multiplexer address N CAM ID N multiplexer address 1 128 In case the keyboard controls the multiplexer select the camera 1 16 N Enter N channel Number 1 16 When the keyboard controls the multiplexer please refer to concerned operation manual of the multiplexer 10
10. hich there are 6 preset points Edit Track Press TELE to edit down page and press WIDE to edit up page Each track involves 16 preset points and the running speed and the dwelling time of each preset position Display No 01 Point 001 Please Enter lt 1 64 gt Description The Ist preset position in the track is 001 Display No 01 Speed 001 Please Enter lt 1 8 gt Description The speed of the 1st preset point in the track is the Ist class Display No 01 Time 004 Please Enter lt 1 255 gt Description The dwelling time of the j 1st preset point in the track is 4 seconds Speed Range 1 to 8 Fixed 15rad s for constant dome the range of the dwelling time is 1 to 255 When the No N preset point is set as No 0 then all preset points before the No N preset point in the track will be valid however all numbers of preset points afterward and their speed and dwelling time shall be set as 0 automatically After tracks are edited press OFF to store and exit while push the joystick to exit without storage 6 Run Cruise Track SHOT N Enter Display Input Tour No 01 Description N No of the track from 1 to 6 Function Tour the No N track and stop tour by pushing the joystick 7 Stop Cruise Track SHOT N OFF Display Input Tour No 01 Description N No of the track from 1 to 6 Function Stop the No N t
11. rack or stop tour by pushing the joystick 8 Auto Pan ON Operation of PELCO D and PELCO P Protocols 1 Set the Starting Scan Position Transfer the speed dome to the starting scan position operation AUTO ON Set the Ending Scan Position Transfer the speed dome to the ending scan position operation AUTO OFF Run Auto Pan AUTO ENTER 2 Auto Pan operation takes the following parameters You must set these parameters before using a Auto Pan command to begin the scan operation You can use the scan Stop command or PT scan stop command to stop the scan Setting scan condition Auto Pan Position First specify position second specify position Auto Pan Speed and Direction Note For COP 2 Protocol the way of operation is as follows AUTO P1 ON P2 OFF Display Input 1st No 001 Description P1 the starting scan No of preset point from 1 to 128 which should be set already Display Input 2nd No 002 Description P2 the ending scan No of preset point from 1 to 128 which should be set already If P1 P2 or P1 and P2 are coincided the speed dome will make scan in range of 360 9 Stop Auto Pan AUTO OFF only for COP 2 protocol or push the joystick to stop scan 15 Use the Joystick to control the speed dome ra camera u You can use the speed joystick to control the ppr lt ar gt RIGHT Pan Tilt direction and speed of the speed dome N N Ce oe randomly The speed of
12. tons CALL To call the preset position PRESET To set the preset position SHOT To set up or call cruising track AUTO To control auto horizontal rotation for pan tilt WIDE To a wide angle TELE To turn to a telescopic range FAR To make focus far manually NEAR To make focus near manually OPEN To open iris CLOSE To close iris ON Switch on the setting of function OFF Switch off the setting of function F1 Auxiliary control buttons F3 Switching control between intelligent speed dome and multiplexer 0 9 Number key Clear To clear inputted data Enter To confirm 2 Rear Panel Figure 2 DC12W POWER ID CODE m R3485 OUT 8 8 I en food E DC12 POWER O e 8 CONTROL OUTPUT Figure 2 A Power input connector input DC12V power B ID Code switch Used to set the protocol in use and the baud rate of communications C Communication connector RS485 The controller is connected to adapter box by specific cable IV Setting of the Keyboard a The protocol in use and the baud rate of communication of the keyboard are set by the ID CODE in Figure 2 DIP1 DIP4 are used to select type of the communication protocol as per following table DIP status Normal Baud Rate Protocols DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 COP 2 ON OFF OFF OFF OFF ON Santachi OFF ON OFF OFF OFF ON PELCO D ON ON OFF OFF OFF OFF PELCO P 4800 ON OFF
Download Pdf Manuals
Related Search