Lavamat 86760 User Manual - Eurohome Kitchens and Appliances
Contents
1. Compartment for washing powder tablets for main wash il If you use water softener and need the right compartment for the pre wash detergent soaking agent add the water softener to the main wash detergent in this compartment Compartment for liquid conditioner softener finisher starch Important Do not fill compartment above the MAX mark Concentrated conditioner may need to be diluted up to the MAX mark dissolve starch powder Information A small amount of residual water in the compartment for liquid conditioners is normal and will not affect the rinse results Compartment for pre wash detergent soaking agent Only for PRE WASH programme option or for water softener Push the detergent dispenser drawer in fully If using liquid detergent tablets Use the dispensing containers supplied by the detergent industry for adding liquid detergent or tablets Follow the instructions on the deter gent package Operating Instructions Starting the wash programme t 1 Check that the water tap is open 1 2 Starting the wash programme Press the START START PAUSE button pause O The wash programme is started or starts after the end of the time delay set If the DOOR LIGHT indicator flashes red when pressing the START PAUSE button then the door is not properly closed Press the door firmly closed and press the START PAUSE button again If a delay start h2. il Open Press the DOOR LIGHT button The door springs DOOR open LIGHT O Close Press the door firmly closed When the unit is switched on the DOOR LIGHT display shows whether the door can be opened green The door can be opened not when programming is acti vated see the section Programme protection for details off Door cannot be opened red Door is open The washing drum is illuminated when the door is open The light goes out automatically after approx 3 minutes Loading the Washing i IS 1 2 Load the washing Close the door firmly For maximum load see Programme Tables See Sorting and Preparing a Wash Load for information on how to prepare washing correctly Sort and prepare the washing according to type and colour Open the door Press DOOR LIGHT button UN M NG Door springs open Important Do not trap washing when closing the door The fabrics and the appli ance could be damaged 23 Operating Instructions Add detergent conditioner IS 1 24 For information concerning detergent and conditioners see the section Detergent and Conditioners Open the detergent dispenser drawer grasp the drawer at the flap at the bot tom 1 and pull out the drawer to its full extent 2 Add detergent conditioner Compartment for in wash stain treatment tablets veri Only for STAIN programme option
3. Caution Only tighten the screw connection ma EO nually ifs By slowly opening the water tap before putting I the washing machine into operation check that 3 the connection is free of leaks 51 Installation and connection instructions 52 Water drain The drainage hose can either be connected to a siphon or hung in a wash basin or discharge basin or a bath tub Only original hoses may be used for extensions max 3m laid on the floor and then up to 80cm high Customer Service stocks drainage hoses in lengths of 2 7 and 4m Important It is essential to lay the drainage hose without kinks Water drain off inside a siphon The grommet on the hose end fits all standard siphon types VS Secure the connection between the grommet and siphon with a hose clamp Water drain off inside a basin Important Small basins are not suitable for drainage Water could overflow The end of the drainage hose must not be submerged in the pumped out wa ter Otherwise the water could be sucked back into the unit When hanging in a wash basin or a bath tub the drainage hose must be secured with the supplied attachable bend to prevent it slipping The back surge force of the escaping water could otherwise force the hose out of the basin CS Tie the bend to the tap or the wall using a piece of string Delivery heads over 1m To pump off the washing rinsing solution
4. Important Do not use any furniture cleaning agents or aggressive cleaning agents in order to clean panel and control parts Wipe control panels with a damp cloth When doing so use warm wa ter Detergent Drawer if 1 2 Take the conditioner insert out of the Clean the conditioner insert under Clean the compartments with warm The detergent drawer should be cleaned from time to time Pull the detergent drawer out as far as it will go Remove the detergent drawer by pulling sharply middle compartment running water water from the rear side It is best to use a flat brush Push on the conditioner insert as far as it will go so that it is securely in place Operating Instructions 7 Use a brush to clean the entire rinsing in section of the washing machine particularly also the noz zles on the top side of the rinsing in chamber 8 Set the detergent drawer into the guide tracks and push in Washing Drum The washing drum is made of stainless steel Rusting foreign bodies in the washing can cause rust deposits on the drum Important Do not clean the stainless steel drum with decalcifying agents containing acids scouring agents containing chlorine or iron or steel wool Our Customer Service can provide suitable agents ts Remove any rust deposits on the drum using a stainless steel cleaning agent Main door CS Check on a regular basis to see if deposits or foreign objects are prese
5. Control panel eea eaaa aaa aa aaa aa aa aaa aa aaa ea 30 Detergent Drawer urinario rie ga dna cr dero e E 30 Washing Drum s We ea eld e eR X MA Re 31 Man doot 15 rerum Deer p eig Pese qe pe RE e Ras 31 What to do if ocio e a ee 32 Remedying faults iuba be e epic e band Eros d e Geld 32 If the washing results are not satisfactory 36 Carrying out emergency drainage 37 Drain ETC 38 Emergency unlocking of the door eaaa aee 39 Additional Rinse RINSE 2 0 0 0 cece eect eee eee 40 Water Cooling cesser eee adea e det eme dins 41 Additional Rinse and Water Cooling aee 41 Variomatic Loose Spin 42 Programme Protection 43 Child Safety Feature 44 Installation and connection instructions 45 Installation Safety Precautions 45 Installation of the appliance 0 0 0 cece eee ees 46 Transporting the appliance a eee eee 46 Remove transport packaging 46 Prepare the installation place 48 Installation on a concrete base ee 48 Installation on vibrating Hoor 48 Compensate for floor unevenness 49 Electrical connection 50 Water connection 50 Permissible water pressure 50 Water inflow 51 Water drain cese erae dea m RD Pera a edes 52 Delivery heads over Im 52 Technical data oc ree Paes Wee cuc a eb oreet 53 DIMENSIONS pee ee Y RN Ka A EEN EA eee Ps 53 Warranty conditions Customer service cent
6. Customer service centres 56 Israel Electricity amp Electronic Services Evis LTD 19 Hataasia st Raanana Industrial area 43654 Tel 972 9 7448118 Fax 972 9 7603618 e mail evis evis co il Japan Electrolux Japan Ltd Domestic Appliances Depart ment Maruzen Showa Warehouse Building Tookai 4 5 12 Ota ku 143 006 Tokyo Tel 0120 13 7117 Fax 03 3790 5257 Thailand OLYMPIA Thai Ltd 44 Ratchadapisek Road 10320 Bangkok Tel 2 513 6111 Fax 2 513 2574 Hungary Electrolux Lehel KFT AEG Div Erzs bet Kir lyn tja 87 1142 Budapest Tel 00361 467 3200 Malaysia Arzbergh Engineering No 49AJB Jalan Petaling Utama 7 4600 Petaling Jaya Tel 3 795 1084 Fax 3 795 1082 Singapore Arzbergh Engineering 19 Tanglin Road 06 07 Singapore 247909 Tel 65 7356572 Fax 7351124 Slovakia Rep Electrolux Slovakia S R O Seberiniho 1 821 03 Bratislava Tel 02 4333 4322 4355 Fax 02 4333 6976 USA ANDI Co Appl Inc East 65 Campus Plaza Edison New Jersey 0837 USA Tel 201 2258839 Saudi Arabia Alia Trading Corporation P O Box 4101 King Abdul Aziz Street Riyadh Tel 4645977 Al Nahas Est Musaidia Market P O Box 1 15 29 Jeddah Tel 6606852 Slovenia Electrolux Slovenia D O O Traska Ul 132 1000 Ljubljana Tel 61 1234 137 Fax 61 1234 238 South Africa AEG Pty Ltd 55 12th Road P O Box 1 02 64 Kew Johannesburg 2000 Tel 8069111
7. Syria Masri amp Shami P 0 Box 24 96 Damascus Tel 214080 57 Index 58 Index A Aqua Control eee 15 27 Automatic adjustment foot 9 49 C Care agent seria Rl ERA 9 18 Child safety feature 32 44 Coloureds ANS SNE KSE NEEN e 28 29 Conditioner 9 11 19 24 29 Correcting a programme 10 Cottons 00005 11 17 28 29 Cottons Linen Easy Cares 28 Cuttallis pe pP IR A ga A 16 Customer Service 15 31 32 59 D Delay mer 10 12 22 Delicates 000005 11 17 28 Detergent iz sasama ska na 9 18 19 24 Detergent drawer 9 24 Drain zie aie teehee aon de 11 Drain pump 2 eee eee eee 9 38 E Easy ION ccs aa elt 12 28 Easy CareS ccc eee eee 11 17 28 Emergency drainage 37 Emergency unlocking 39 Energy Saving Programme 12 28 F Fashion sociis sees ERAS 12 28 H Handwash 11 29 I In wash stain treatment 9 24 L Linen supid vete ier 11 17 loads oos re eet Adi ss 14 28 M Multi display 10 32 59 0 Opening the door 23 27 39 43 Over dosed eise les 27 P Pre wash 12 20 24 28 Pre wash detergent 9 24 Programme option buttons 12 28 Programme progress display 10 Programme protection 23 43
8. every washing machine has a drain pump which carries liquids up to a height of 1m via the drain age hose calculated from the machine s standing surface Please contact Customer Service for delivery heads of over 1m Technical data Adjustment possibility Filling quantity program dependent Area of use Drum speed spinning Water pressure Dimensions dimensions in mm 850 10 5 Approx 10 5mm max 6kg Domestic See rating plate 1 10 bar 10 100 N cm 0 1 1 0 Mpa 53 Warranty conditions Customer service centres 54 Warranty conditions Customer service centres Weitere Kundendienststellen im Ausland In diesen L ndern gelten die Garantiebedingungen der rtlichen Partner Diese k nnen dort eingesehen werden Further after sales service agencies overseas In these countries our AEG agents own guarantee conditions are applicable Please ob tain further details direct Autres agences trang res assurant le service apr s vente Dans ces pays les conditions de garantie des concessionnaires de la r gion sont vala bles Vous pouvez les consulter sur place Otros puntos de Postventa en el extranjero En estos pa ses rigen las condiciones de nuestros representantes locales las cuales pueden ser consultadas all mismo Ulteriori uffici del servizio tecnico assistenza clienti all estero In questi paesi sono valide le condizioni di garanzia dei partner lo
9. the result of an insufficient rinsing effect Shake or brush out the washing In future perhaps you should turn the washing inside out before washing it Examine your choice of de tergent and if necessary use liquid detergent Operating Instructions Carrying out emergency drainage IS 1 Remove the emergency drainage hose Place the container under the hose Detach the plug of the emergency e f the washing machine no longer pumps off the washing solution emergency drainage must be performed e f the washing machine is in a room where there is a risk of frost emergency drainage must be performed if there is a possibility of frost In addition unscrew the inlet hose form the water tap and place it on the floor Empty the drainage hose Warning Switch off the washing machine before performing emer gency drainage and pull out the mains plug Caution The washing solution escaping from the emergency drainage hose may be hot There is a risk of scalding Allow the washing solution to cool down before performing emergency drainage Place a flat collecting vessel in order to collect the washing solution which is draining off of the base outwards and pull it off Fold open the flap in the right section from its holder drainage hose by turning it anticlock wise and pull it out The washing solution runs out Depend ing on the amount of solution it may be necessary to empty
10. EIER 10 Programme Selector ooooococccccccccc sss 10 Programme Option Buttons 00 0c cece eee 12 Programmable functions 13 Consumption Values and Programme Times 14 Wash Time Display seisi aa ere eee greed nar G a X art 14 What does UPDATE mean 15 Anti flood system Aqua Control Aqua Alarm 15 Before the First Wash 16 Preparing a Wash Load 16 Sorting and preparing a wash load sssssssseseeseeeeee 16 Washing Types and Care Symbols eaaa eaaa ee 17 Washing Detergents and Care Agents 18 Which washing detergent and care agent sslsuuuu 18 How much washing detergent and care agent 18 Wat r softenel noc mese ere Dar Roe toca Da deser ap wees 18 Running a Wash Cycle 0 es 19 Brief nstr ctions esee ec ese uA we rim eR Pi detur 19 Setting the wash programme 20 Changing Spin Speed selecting RINSE HOLD 21 Setting the delay timer soaking duration 22 Opening and closing the door 23 Loading the Washing 23 Add deterqent Conditioner EE 24 Starting the wash programme 25 Washing Programme Progress 26 Washing cycle complete Removing the washing 27 Programme Table 28 Washifhg d o EC nu bL M Lui REM 28 Separate Rinse Conditioning Starching Treating 29 Separate Spinning kas die ANENG y KANAAN RE AA Bead 29 Cleaning and Care ce Verse wa Lek mre xar 30
11. P mp out ec bener boi 27 R Rating plate nananana 9 50 59 Refresh lt aaa de rl des 12 28 RINSE saa pic or pales Meee e 40 Rinse hold 11 21 27 Rinsing nei o ee eee 29 Risk of frost ee eee eee 6 37 S KEE 12 Shortspin NEE Be Ri e 11 sik 11 17 29 hand washable e 11 Soaking iria 12 22 Soaking agent 24 LEI EE 8 24 Spinning 11 19 21 23 26 29 Stain a 9 12 20 28 36 Starehing s s eeiofac i a E AMI 11 29 T Time Saver coi lr 13 28 U Updates uice gak nei unsers 15 W Warranty llsslleeeseee 6 32 54 Wash time ulcere lee pe e ah 14 Washing powder 9 18 Water hardness 8 18 pumping out 11 27 softener Sanan aaa Ag 8 9 18 24 Water Cooling 41 Wool amana naa x ts Ka aa 29 Woollens wb Se ii da 11 17 hand washable e 11 Service Service In the chapter What to do if some faults are listed which you can remedy yourself Look there first if a fault occurs If you do not find any information there please consult your Customer Service You can find the addresses and telephone numbers in the section Customer Service Centres Always prepare in advance for the discussion By doing so you will sim plify the diagnosis and the decision on whether customer service is necessary Note the PNC number and S num ber You will find both on the rating plate on the inside of the door of your washin
12. before pumping out at the end of the main wash cycle by adding cold water This setting only works on the COTTONS LINEN EASY CARES programme when the temperature is above 40 C When the appliance is supplied water cooling is not set except for the SENSITIVE programme option Setting the water cooling function Turn the programme selector to SHORT SPIN Press the PRE WASH button for at least 5 seconds After the button has been kept pressed for 5 seconds MAIN WASH flashes on the pro gramme progress display for 5 seconds Release the PRE WASH button while MAIN WASH is flashing Once it has stopped flashing the water cooling function is set It remains set until it is cancelled again If you wish to check whether the water cooling function is set Turn the programme selector to SHORT SPIN Press the PRE WASH button briefly When MAIN WASH flashes in the programme progress display the wa ter cooling function is set Cancelling the water cooling function Turn the programme selector to SHORT SPIN Press the PRE WASH button for at least 5 seconds MAIN WASH flashes in the programme progress display as soon as the button is pressed Af ter 5 seconds MAIN WASH will stop flashing and remain constantly illu minated for 5 seconds While MAIN WASH is constantly illuminated release the PRE WASH button Once MAIN WASH is no longer illuminated the water cooling function has been cancelled Water cooling
13. in its original position in order to can cel the programme protection Cancelling programme protection IS Press and hold down the PRE WASH and SENSITIVE buttons simultane ously for 5 seconds The programme progress indicator flashes for 5 seconds and then remains illuminated constantly for 5 seconds Pro gramme protection has been cancelled 43 Operating Instructions 44 Child Safety Feature If the child safety feature is set the filling door can no longer be closed and no washing program can be started Setting the child safety feature IS Useacoin to turn the rotary knob on the inside of the filling door clockwise as far as it will go N Warning The rotary knob must not be in a vertical position after A adjustment otherwise the child safety feature is not active The ro tary knob must project as shown in the diagram Si Cancelling the child safety N E feature CS Turn the rotary knob anticlockwise as far as it will go Installation and connection instructions Installation and connection instructions Installation Safety Precautions Do not tilt the washing machine onto its front or onto its right side viewed from the front Electronic components can get wet Check the washing machine for transport damages A damaged unit must never be put into operation under any circumstances In the event of damage please contact your supplier Ensure that all parts of
14. increases water consumption and the programme dura tion Additional Rinse and Water Cooling You can combine the additional rinse cycle with water cooling Setting as for Additional Rinse and Water Cooling 41 Operating Instructions 42 Variomatic Loose Spin A spin function that can be set as an integrated part of the final spin The washing clings less to the drum wall and can be removed more eas ily May be selected with COTTONS LINEN EASY CARES Setting loose spin Turn the programme selector to SHORT SPIN Press the STAIN button for at least 5 seconds After the button has been kept pressed for 5 seconds END flashes on the programme progress display for 5 seconds Release the STAIN button while END is flashing Once it has stopped flashing the loose spin function has been set It will remain set until it is cancelled again If you wish to check whether the loose spin function is set Turn the programme selector to SHORT SPIN Press the STAIN button briefly If END flashes in the programme progress display the loose spin func tion has been set Cancelling loose spin Turn the programme selector to SHORT SPIN Press the STAIN button for at least 5 seconds END flashes in the programme progress display as soon as the button is pressed After 5 seconds END will stop flashing and remain constantly illuminated for 5 seconds While END is constantly illuminated releas
15. ingly After the end of this programme step the END display lights up Open the door As soon as the indicator next to the DOOR LIGHT button is green the door can be opened not if programme security is activated For details see Programme security Remove the washing Turn the programme selector to OFF After washing pull the washing detergent drawer out a little so that it can dry out Leave the door ajar so that air can circulate in the drum If the display OVER DOSING lights up too much OVER DOSING O washing detergent was used in the washing program just ended During the next wash pay attention to the dosing information of the washing detergent manufacturer and pay attention to the filling quantity Caution If the washing machine is not used for a long time Close the water tap and disconnect the washing machine from the electricity mains Anti flood system Aqua Control with Aqua Alarm does not function if the power supply is interrupted 27 Operating Instructions Programme Tables Washing The tables do not show all the possible settings only those most likely to be selected for everyday purposes Type of washing Care symbol Cottons Coloureds Cottons Coloureds Easy Cares Delicates 28 Max Load Dry weight 3kg 3kg 1kg 3kg 3kg or 15 20m net curtains 3kg Programme selector Temperature in C ENERGY SAVING 60 COTTONS LINEN
16. out minor floor unevenness Instead always adjust the adjustment foot 49 Installation and connection instructions Electrical connection d Details of the mains voltage current type and required fuses can be found on the rating plate The ra ting plate is located at the top above the filling door For permanent electrical connection within the electrical circuit provi sions must be made which allow for electrical disconnection of the ap pliance from the mains with a contact opening of at least 3 mm at all poles Suitable devices include circuit breakers fuses threaded fuses must be entirely removed from the socket ground fault circuit inter rupters and contactors Permanent connection may only be carried out by an authorised electrician This appliance complies with the following EC directives The Low Voltage Directive 72 23 EU with changes The EMC Directive 89 336 EU with changes Water connection i The washing machine has safety features which prevent back contami nation of the drinking water and which conform to the national regu lations of the water authorities e g for Germany DVGW guidelines This means that additional protective measures in the installation are not necessary Important Units for connecting to cold water must not be connected to hot wa ter Use only new hose sets for the connection Permissible water pre
17. spin speed can still be changed or RINSE HOLD can be set Other settings cannot be changed Stopping the programme Turn the progamme selector to OFF in order to stop the washing prematurely The programme can be interrupted at any time with the START PAUSE button and can be continued again by pressing this button again Operating Instructions Washing cycle complete Removing the washing IS 1 oo al Once the wash programme has come to an end the END indicator illu minates on the programme progress display e f the EASY IRON programme was selected and anti crease phase of approximately 30 minutes follows the programme end Here the multi display shows the remaining time and the END indicator illumi nates During the anti creasing phase the door can be opened at any time and the washing can be removed e f RINSE HOLD was selected the display next to the START PAUSE button flashs After a rinse hold the water must first be pumped out Either press the START PAUSE button water is pumped out and the washing is spun according to the completed programme using the RINSE HOLD spin speed button it is possible to change the spin speed during spinning or Turn the programme selector to DRAIN and press the START PAUSE button the water is pumped off without spinning or Turn the programme selector to SPIN or SHORT SPIN and press START PAUSE button water is pumped out and the washing is spun accord
18. 1226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 Estonia Electrolux Estonia Ltd Mustam e tee 24 EE0006 Tallinn Tel 372 6 650 090 Fax 372 6 650 092 Hongkong Wo Kee Services Ltd 585 609 Castle Peak Road Kwai Chung N T Hongkong Tel 2494 4000 Korea South Core Incorp 3 F Chewoo Bldg 200 Nonhyun Dong Kangnam Ku Seoul Telefon 82 2 549 89 61 Croatia Electrolux D O O Suplova 7 10000 Zagreb Tel 1 61 19512 Fax 1 61 19513 Kuwait Arabian Gulf Ali Al Ghanim Est P O Box 10 83 Tel 5322463 Fax 5242114 Lebanon Adib amp Assaferi P O Box 539 Tripoli Latavia Electrolux Latavia Ltd Terlaton Street 42 44 1011 Riga Tel 371 2 297821 Fax 371 2 821286 Lthuania Electrolux Lthuania Verkui 29 2600 Vilnus Tel 372 272 3326 Fax 372 272 3366 Namibia AEG NAMIBIA PTY LIM ITED Jeppe Street Northern Industrial Area Windhoek Tel 061 21 6082 4 Fax 061 217838 New Zealand Euro Life New Zealand Ltd Privat Bag 58 Symonds Street Auckland Tel 09 525 2222 Nouvelle Caledonie Socometra N C B P 483 Nouman Tel 275444 Oman Moshin Haider Darwish P O Box 1 35 Muscat Tel 703743 Poland Electrolux Poland Sp z0 0 ul Domaniewska 41 02 034 Warszawa tel 022 874 33 33 fax 022 874 33 00 Russia Electrolux Russia Ltd 16 Olympiysky prospekt 129090 Moscow Tel 095 937 7837 Fax 095 926 5513 55 Warranty conditions
19. 8 WOOL amp Handwash 30 2 42 0 18 35 1 Note Programme setting for testing in accordance with or in support of Stand ard EN 60 456 and IEC 60 456 Wash Time Display i The wash times for the wash programmes Q WASH depend on the usual washing practice and y LI TIME the ambient conditions at the place of in stallation The washing type and quantity the type of washing detergent the water temperature and the room temperature etc can influence the duration of the wash programme Operating Instructions What does UPDATE mean The wash programmes in your washing machine are controlled by soft ware New types of fabric or new detergents may require new wash pro grammes in the future In most cases the software can be adapted to this For further information on a possible update please contact customer service Anti flood system Aqua Control Aqua Alarm In the event of damage to the supply hose the system blocks the fur ther supply of water to the unit directly st the water tap If water escapes at another point the drainage pump pumps the water off automatically even if the unit is switched on It is merely neces sary for the washing machine to be connected to the mains If the anti flood system responds a warning signal sounds at the same time Operating Instructions Before the First Wash IS Run a wash cycle without washing COTTONS LINEN EASY CARES 95 programme with half the amou
20. EASY CARES 20 to 95 REFRESH 30 COTTONS LINEN EASY CARES 20 to 60 EASY IRON 40 REFRESH 30 DELICATES 30 40 FASHION 40 Possible Programme options or functions PRE WASH SENSITIVE STAIN TIME SAVER PRE WASH SENSITIVE STAIN TIME SAVER PRE WASH SENSITIVE STAIN TIME SAVER PRE WASH STAIN TIME SAVER PRE WASH STAIN TIME SAVER Operating Instructions Possible Type of washing Max Load Programme selector Programme Care symbol Dry weight Temperature in C options or functions Wool Handwash va WI 2kg WOOL y COLD to 40 Silk Handwash WI 1kg SILK amp 30 TIME SAVER 1 The load amount inquiry operates in accordance with the EN 60456 standard load 2 A 10 litre bucket holds around 2 5kg of dry clothes cotton 3 Programme settings for testing in accordance with or in support of standard EN 60 456 and IEC 60 456 are described in the Chapter Consumption Values and Programme Times 4 Creasing can be largely avoided by keeping wash loads under 1kg roughly 5 to 7 easy care men s shirts Separate Rinse Conditioning Starching Treating Type of washing EE Programme selector Cottons Coloureds 6kg STARCHING Wool Handwash 2kg LUE SAVER Separate Spinning Max load Type of washing dry weight Programme selector Cottons Coloureds 6kg SPIN Easy Cares 3kg Delicates 3kg Wool Handwash 2kg SHORT SPIN Silk 1kg Operating Instructions 30 Cleaning and Care Control panel
21. IN The water is pumped out at the end of a rinse hold and spin or hand washed cottons linen and easy cares are spun separately SHORT SPIN The water is pumped out at the end of a rinse hold and short spin or delicate fabrics delicates woollens are given a separate short spin at low revs DELICATES Wash programme for delicates at 30 C or 40 C WOOL amp Hand wash Wash programme cold to 40 C for machine washable woollens and for hand washable woollen fabrics bearing the Uv care symbol hand wash SILK y Hand wash Wash programme at 30 C for hand and machine washable silk As silk is a very sensitive fabric we recommend that you only wash one item of clothing at a time and that such items never be washed with other rough fabrics A still more gentle wash is possible for extremely sensitive silk fabrics using the TIME SAVER button 11 Operating Instructions 12 H FASHION A particularly gentle special programme at 40 C for modern fabrics such as viscose modal cupro lyocell with a gentler wash action than the DELICATES programme but washing more thoroughly than the hand wash programmes REFRESH A special programme lasting approx 20 minutes at 30 C to give fabrics a quick wash such as for example very slightly soiled sports clothes that have been worn only once EASY IRON Wash programme at 40 C for easy care fabrics that will only need to be ironed lightly if at all at the conclu
22. OKO LAVAMAT 86760 update The environmentally friendly washing machine User information Dear Customer Please read this user information carefully Pay particular attention to the section Safety on the first Info pages Please keep this user information in a safe place for later reference Pass it on to any future owners of the unit The warning triangle and or signal words Warning Caution Impor tant emphasise information which is important for your safety or for the unit s functional reliability It is imperative that this information is observed his symbol guides you step by step through the operation of the appli ance Next to this symbol you will find additional information and practical tips on using the appliance Tips and information on economical and environmentally responsible use of the unit are identified with the clover leaf For any faults which occur this user information contains information on how to remedy these faults yourself See the section What to do if Printed on recycled paper Thinking ecologically means acting ecologically Contents Operating Instructions aaa 6 SEI A EET 6 DiSPpOSall ME 8 Environmental ms 8 Unit description aaa anganan Gak Gana eee Pr Dee Gn 9 Front VIEW saa a aa Aa na Se EE a rre el E Da er 9 Drawer for detergent and Care agent 9 Control Pandanaran anaa pb pube et EE ee mad
23. and particularly delicate wash items wi Fabrics such as wool wool mixtures and silk which carry these care symbols require a very gentle wash cycle The WOOL y Hand wash and SILK amp Hand wash programmes are suitable for this type of fabric Important Fabrics which bear the care symbol XT Do not wash may not be machine washed 17 Operating Instructions Washing Detergents and Care Agents Which washing detergent and care agent Use only washing detergents and care agents which are suitable for use in washing machines Always follow the manufacturer s instructions How much washing detergent and care agent The amount to be used depends on e the dirtiness of the washing e the hardness category of the mains water supply e the filling quantity If the detergent manufacturer gives no details of the dosing quantities for minimum loads add one third less for half loads and in the case of very small loads and for EASY IRON only half the amount of detergent recommended for a full load Refer to the detergent care agent manufacturer s instructions on use and dosage Water softener For medium to high water hardness hardness class upwards you should use softener Refer to the manufacturer s instructions Then al ways add the appropriate amount of detergent for hardness class soft The responisable water works will provide information on the local water hardness Since the water softener is rinsed i
24. as been set The delay time set counts down the remaining time until the start of the programme is displayed in the multi display in hours remaining During this time you can add washing or change the delay time or cancel it e Adding washing Press the START PAUSE button The door can be opened Then close the door and press the START PAUSE button again Changing or stopping the delay time Press the DELAY TIMER button until the desired time is displayed when the duration of the pro gramme is displayed e g 20 minutes the wash programme starts immediately 25 Operating Instructions 26 Washing Programme Progress i Programme progress display PRE WASH O Prior to the start the programme steps chosen are MAIN WASH O displayed by the Programme progress display RINSE During the washing programme the current RINSE O programme step is displayed SPIN END O Multi display The expected time remaining in minutes 1 T1 WASH up to the end of the programme is shown O time in the Multi display The multi display indicates the estimated duration in minutes of the programme These timings are estimates and can vary according to in coming water temperature type and quantity of laundry out of bal ance spin detection and foam detection During the programme countdown the remaining time can be recalculated due to any of the above factors Changing spin speed During the washing programme the
25. ater from the water mains Use rain water or service water only if it meets the requirements defined in DIN 1986 and DIN 1988 e Frost damage is not covered by the warranty If the washing machine is in a room subject to possible frost hazards emergency emptying must be carried out if there is a risk of frost see the Section Carry ing out emergency emptying Operating Instructions Safety of Children and Infirm Persons e Packaging materials e g films polystyrene can be dangerous for children Risk of suffocation Keep packaging away from children e The appliance is not intendet for use by young children or infirm per sons without supervision Children frequently cannot recognise hazards involved in handling electrical appliances Therefore ensure that they are properly super vised during operation and never allow children to play with the washing machine there isa risk that they can lock themselves inside it Ensure that children or small animals do not climb into the washing machine s drum When disposing of washing machines pull out the mains plug destroy the door lock cut off the electrical supply lead and dispose of the plug and remaining cable This means that playing children cannot shut themselves in and cannot encounter a potentially lethal hazard General Safety Repairs to washing machines may only be carried out by skilled persons Improper repairs can cause significant hazards for the user If you
26. ber of REFRESH rinses spin speed to suit the type of FASHION COTTONS LINEN EASY CARES washing as well as the water tem sk V perature Cour 20 OFF WOOL 40 e 30 4 Switches the washing machine off DELICATES y the machine is switched on at all other positions To correct programme settings that have been selected accidentally turn the programme selector to the OFF position The initial position is reinstated Operating Instructions COTTONS LINEN EASY CARES Wash programme between 20 C and 95 C may be used for all cotton and linen washing cottons linen easy cares blended fabrics e g cot ton polyester and synthetics The wash programme adjusts to suit the various types of fabric and quantities If there is mostly cotton linen a suitable cottons linen programme is carried out if there is more syn thetic material a programme for easy cares is selected If the machine is loaded exclusively with easy cares the quantity should not exceed 2 5 kg in order to avoid creasing STARCHING Separate starching separate rinsing separate conditioning or separate soaking of damp washing 1 rinse liquid conditioner is added from the compartment amp spin If a separate rinse is carried out do not put any conditioner into the compartment DRAIN The water is pumped away after a rinse hold without spin Rinse hold means the washing remains in the last rinsing water and is not spun SP
27. cali Queste condizioni possono essere esaminante sul luogo Servicos de assist ncia t cnica no estrangeiro Nestes pa ses s o v lidas as condic es de garantia dos concession rios locais podendo a ser consultadas Tov bbi vev szolg lati irod k k lf ld n Ezekben az orsz gokban a mi AEG vev szolg latainkn l saj t j t ll si felt telek alka Imazhat k A tov bbi adatokat k rj k k zvetlen l szerezz k be U A E Abu Dhabi Jordan Malta Universal Trading Company Jordan Household ITC P O Box 43 99 Supply Co Ltd International Trading Com Tel 335331 P O Box 3 68 pany Amman Tel 69 70 50 White House Building Mountbatte Street Blata L Bajda Tel 220644 Egypt Kanada Mauritius Middle East Commercial EURO LINE Appliances Happy World Centre Ltd Center 2150 Winston PARK Drive 20 P O 7 54 P O Box 19 Oakville Ontario L6H 5V1 1 Chausee Street Kairo Heliopolis Tel 905 829 3980 Port Louis Tel 29917 31634 Fax 905 829 3985 Tel 25355 Warranty conditions Customer service centres Australia ANDI Co Pty Ltd 9 Kingston Town Close Oakleigh VIC 3166 Tel 03 9569 1235 Fax 03 9569 1450 Bahrain Arabian Gulf A A Zayani amp Sons P O Box 9 32 Bahrain Tel 261060 Bulgaria Electrolux Bulgaria E O O D 91 Levski Blvd 1000 Sofia Tel 2 806676 Fax 2 980 5276 Cyprus Hadjikyrlakos amp Sons Ltd Prodromou 121 P O Box 21587 Nicosia 1511 Service Telephones Nicosia 02 48
28. e amount of deter gent used Follow the detergent manufacturer s recommendations Tighten the inlet hose screw connection Check the drain hose and re place it if necessary Close cover correctly Stop the programme remove the washing caught in the door Restart the programme Close the emergency empty ing hose see section Carry out emergency emptying Call your local Service Force Centre if the emergency emptying hose is leaking 33 Operating Instructions 34 Problem The drain pump runs constantly even when the appliance is switched off Fabric softener was not rinsed in compart ment amp for condition ers is filled with water Washing is heavily creased The washing has not been spun as dry as usual The washing is not suf ficiently spun Water is left in the drum Error code LO appears The door cannot be opened when appliance is switched on Possible cause The Aqua Control anti flood system has been activated The insert in the comparti ment for conditioners is not correctly attached or is blokked Probably too much washing has been put in drum The washing was not able to be distributed evenly in the drum prior to spinning Drain hose is kinked Maximum pump height emptying height 1m from base surface of the appli ance is exceeded Drain pump is blocked At the siphon connection Si phon is blocked The door is locked for safety
29. e the STAIN button Once END is no longer illuminated the loose spin function has been can celled Operating Instructions Programme Protection To safeguard a programme setting against unwanted changes e g program selector turned option buttons pressed etc you can set the programme protection This prevents your washing being damaged i It is possible to set or cancel the programme protection at any time during a programme Selecting programme protection Eg 1 Select the desired wash programme settings 2 Press the START PAUSE button to start the programme 3 Press and hold down the PRE WASH and SENSITIVE buttons simultane ously for 5 seconds The programme progress indicator will flash for 5 seconds programme protection has been set il As long as the programme protection is set you cannot make any other settings The door cannot be opened using the DOOR LIGHT button Even after the wash cycle has finished you will need to cancel the pro gramme protection before you can open the door If an attempt is made to change the selected settings during the wash cycle by activating a button the programme progress display will flash for 5 seconds If you attempt to change the selected setting by turning the pro gramme selector the programme progress display will flash until the original setting of the programme selector is restored The wash cycle is not influenced in either case i The programme selector must be
30. g machine NC IA S NO iste mE Answer as precisely as possible What form does the fault take Under what circumstances does the fault occur Does the multi display show an error message When do you incur costs even during the warranty period f you could have remedied the fault yourself with the aid of the fault table see the section What to do if If several journeys by the customer service technician are necessary because for example he did not receive all the important information before his visit and must collect spare parts These multiple trips can be avoided if you prepare your phone call as described above 59 E From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de 9 Copyright by AEG 822 943 585 01 170403 01 Subject to change without notice
31. hine Do not place folded washing into the drum Observe such washing instructions as wash separately and wash separately several times Operating Instructions Washing Types and Care Symbols The care symbols help you choose the correct wash programme Wash ing should be sorted according to type and care symbol The tempera tures indicated in the care symbols are all maximum temperatures Cottons Fabrics made from cotton and linen with this care symbol will with stand maximum wash actions and high temperatures The COTTONS LINEN EASY CARES programme is suitable for this type of washing Linen Fabrics made from cotton and linen which carry this care symbol will withstand maximum wash actions The COTTONS LINEN EASY CARES programme is suitable for this type of washing Easy care washing Fabrics such as treated cotton cotton mixed fabrics and synthetics which carry this care symbol need a gentler wash action The COTTONS LINEN EASY CARES and EASY IRON programmes are available for this type of washing Delicates Fabrics such as those with layered fibres microfibres synthetics and cur tains with this care symbol require particularly careful handling The DELICATES programme is appropriate for these types of washing Viscose Modern fabrics such as viscose cupro lyocell modal and others require particularly careful handling The FASHION programme is appropriate for these types of washing Woollens silk
32. inute The speed of intermediate spins depends on the selected programme and cannot be changed 21 Operating Instructions 22 Setting the delay timer soaking duration A Delay timer The DELAY TIMER button makes it possible to delay the start of a wash programme by 1 to a maximum of 19 hours Select wash programme WESH Press DELAY TIMER button iE AJO me Press START PAUSE button O DELAY TIMER O When start delay has been set the DELAY TIMER display lights up Depress the DELAY TIMER button until the desired start delay appears e g IZh fora 12 hour delay to the start of the programme If 3h is displayed and the button is pressed again then the delay timer is can celled The duration of the set wash programme will now appear in the display in minutes e g 2 The set delay timer can also be cancelled it the programme selector is set to the OFF position Soaking duration With depressed PRE WASH button by pressing the DELAY TIMER but ton the duration of soaking can be extended by 1 to a maximum of 19 hours Press the PRE WASH button Press DELAY TIMER button Soaking is set the WASH TIME indicator illuminates The soaking time is now increased by 1 hour By repeated pressing of the DELAY TIMER button the soaking times can be increased in steps of an hour The WASH TIME and DELAY TIMER displays light up Operating Instructions Opening and closing the door IS IS
33. lders on the appliance s rear side and remove the hoses and mains cable IS 1 46 Installation of the appliance H Washing machines with curved panels are not suitable for installing Do not place the washing machine on its front or on its right side viewed from the front Otherwise electrical components can get e Never transport the unit without the transport safeguard Do not re move the transport safeguard until the appliance is at the installation location Transporting the unit without the transport safeguard can e Lift the appliance neither by an open filling door nor by the base When transporting the unit with a sack trolley e Attach the sack trolley only at the side The sack trolley shovel must not be longer than 24 cm otherwise the float switch can be de E IN Y D d TO Vi CTT i Installation and connection instructions on 0 o Pull both hose holders off the ap pliance with a strong pull The special spanner A and the caps B 2 each and C 1 each are supplied with it Remove the screw D including the compression spring with the special spanner A Cover the hole with the cap C Important When fitting the plastic caps press until they snap into the rear panel securely Remove the two screws E with the special spanner A Remove the 4 screws F Remove the transit bar C Screw the 4 screws F back in for
34. mmes Length of programmes Without With TIME SAVER Programme TIME SAVER Button Button pressed pressed once twice COTTONS LINEN e a EASY CARES at 60 C 119 mins 91 mins 63 mins UO M 68 mins 52 mins for example DELICATES at 30 C Programmable functions The programmable functions Extra Rinse RINSE Water Cooling and Variomatic Spin are described in the Chapter What to do if 13 Operating Instructions 14 Consumption Values and Programme Times The following table gives the values for selected programmes under standard conditions Consumption values depend on the selected pro gramme settings optional functions washing type and quantity water pressure such as water inlet temperature water hardness room tem perature or detergent used etc The tables do however give a helpful guide for normal household use Programme Selector Type of Load Water Energy Time in Temperature material in kg in litres in kWh minutes ENERGY SAVING 1 Cotton 6 42 1 02 120 COTTONS LINEN EASY CARES 95 Cotton 6 50 2 05 148 COTTONS LINEN EASY CARES 60 Cotton 6 50 1 08 119 COTTONS LINEN EASY CARES 40 Cotton 6 58 0 66 116 COTTONS LINEN EASY CARES 60 i 1 Synthetics 3 56 0 95 91 TIME SAVER press once COTTONS LINEN EASY CARES 40 Sumi 3 3 ques m nthetics l TIME SAVER press once H JUS COTTONS LINEN EASY CARES 40 TIME SAVER press twice Synthetics 3 50 0 58 59 DELICATES 30 Synthetics 3 56 0 36 6
35. n before the main detergent water pre softening 80 of the stated quantity of softener shown on the package is sufficient Water hardness details Water hardness in dH Water hardness in mmol Hardness class me E German hardness scale millimol per litre soft 0 7 to 1 3 Il medium hard 7 14 1 3 2 5 Ill hard 14 21 2 5 3 8 IV very hard greater than 21 greater than 3 8 Operating Instructions Running a Wash Cycle Brief Instructions IS 1 o0 P WN A wash cycle consists of the following steps Set the correct wash programme select the programme and temperature using the programme selector if required select programme option If required change the spin speed select rinse hold If required set the DELAY TIMER Open the door and load the washing Close the door Add detergent conditioner Start the wash programme by pressing the START PAUSE button When the wash programme has ended Important If the wash cycle has ended with a rinse hold activate DRAIN SPIN or SHORT SPIN before opening the door Open the door and remove the washing Switch off the washing machine set the programme selector to OFF 19 Operating Instructions Setting the wash programme 20 With the programme knob set ENERGY SAVING OFF the desired wash programme and AS o EASY IRON For suitable programme correct temperature and possible additional programs for the respective
36. nt in or at the rubber sleeve behind the door and remove 31 Operating Instructions What to do if Remedying faults In the event of a fault try to solve the problem yourself with the aid of the information provided here If you use the Customer Service for one of the faults listed here or to remedy an operating error the Customer Service technician s visit will not be free of charge even during the warranty period e f the fault code E t or 2 is shown in the O wast Multi display you may be able to remedy L TIME the problem yourself see the faults table below When you have remedied the fault press the START PAUSE button With all other displayed faults C plus number or letter switch appli ance off and on again Reset the wash programme and press the START PAUSE button If the fault code is displayed again please contact the Customer Service department quoting the fault code Problem Possible cause Remedy d Plug in the mains plug plugged in The house fuse has blown Replace the fuse abing machine doc Close door Lock must en not work Door is not properly closed gage audibly Keep the START PAUSE but ton pressed until the pro gramme starts START PAUSE button has not been pressed long enough Cancel child safety feature see section Child safety feature Door cannot be closed Us Ma switched On Water tap is closed Open water tap ee Close water tap Di
37. nt of washing detergent This removes any residues from the drum and solution container which may have been left during manufacturing Preparing a Wash Load Sorting and preparing a wash load e Sort the washing according to care symbol see Washing Types and Care Symbols Empty all pockets Remove metal objects paper clips safety pins etc n order to prevent the washing tangling and being damaged close zippers button up duvet covers and pillow cases and tie up loose straps such as from aprons e Turn articles with double layered fabric inside out sleeping bags anoraks etc n the case of knitted coloured fabrics and also wool and fabrics with jewellery attached turn inside out e Place small and delicate articles baby booties stockings bras etc into a washing net a pillow case with zipper or in large socks before washing Handle curtains with particular care Metal fittings or burred plastic fittings must be removed or tied into a net or bag We cannot accept liability for damage Do not wash coloured and white washing together This could trans fer colour to white washing or turn it grey New coloured items often have an excess of colour It is better to wash such items separately the first time Mix small and large items of washing This improves the wash effi ciency and the washing is more evenly distributed during the spin cy cle Shake out washing before placing into the washing mac
38. o gramme selector has been moved during the wash cy cle Remedy Open water tap fully Close the water tap Unscrew the inlet pipe from water tap and from the appliance and clean the filter No negative influence on the rinse results use a liquid de tergent if necessary Make another selection Turn programme selector to its original position see Programme security 35 Operating Instructions 36 If the washing results are not satisfactory If the washing has turned grey and if limescale is deposited in the drum then Too little detergent was used he wrong detergent was used Special soiling was not pre treated Program or temperature not set correctly e f multi component detergents are used the individual components were not used in the correct ratio If there are still grey spots on the washing Washing soiled with ointments grease or oils was washed with too little detergent Too lower temperature was used for washing A frequent cause is that softener particularly that in concentrated form has reached the washing Wash out such spots quickly and use the softener concerned carefully If at the end of the last rinse foam is still visible Modern detergents can also cause foam in the last rinse However the washing is still sufficiently rinsed If there are white remnants on the washing These are insoluble components of modern detergents They are not
39. onds RINSE will flash in the programme progress display for 5 seconds While RINSE is flashing release the SENSITIVE button Once the flash ing has stopped the additional rinse has been set It will remain set un til it is cancelled again When the additional rinse has been set the RINSE indicator in the programme progress display is illuminated be fore the programme starts and during the additional rinse If you wish to check whether the additional rinse is set Turn the programme selector to SHORT SPIN Press the SENSITIVE button briefly If RINSE flashes in the programme progress display the additional rinse has been set Cancelling the additional rinse Turn the programme selector to SHORT SPIN Press the SENSITIVE button for at least 5 seconds Immediately the button is pressed RINSE will flash in the programme progress display After 5 seconds RINSE will stop flashing and remain constantly illuminated for a further 5 seconds While RINSE is constantly illuminated release the SENSITIVE button Once RINSE is no longer illuminated the additional rinse has been cancelled An additional rinse cycle increases water consumption and the pro gramme duration Operating Instructions Water Cooling H IS i 1 2 It may be necessary to cool down the water before pumping it out in order to prevent thermal damage to the plastic drainage pipes The water is cooled down
40. packaging of your washing machine correctly All pakka ging materials used are environmentally compatible and recyclable Plastic parts are identified with internationally standardised abbrevi ations gt PE lt for polyethylene e g packing films gt PS lt for polystyrene e g cushion parts always CFC free gt POM lt for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposing of your old appliance When you put your unit out of operation one day please bring it to your nearest recycling centre or to your dealer We Environmental Tips You do not need to use a pre wash cycle or soak for washing with av erage soiling This saves detergent water and time and protects the environment When loaded to the capacities indicated the washing machine is es pecially efficient For small loads use only one half to two thirds of the recommended quantity of detergent By pre treating stains and marks you will be able to wash at a lower temperature e t is often possible to wash without using softener Give it a try If you use a drier your washing will be soft and fluffy even without a softener For medium to high water hardness from hardness range see De tergents and Conditioners you should use water softener The detergent can then always be dosed as for hardness range soft Opera
41. place the pump cover Laterally insert the webs on the cover into the guide slots and screw on the cover in a clock wise direction 6 Close the emergency emptying hose and place it in the holder 7 Close the flap Emergency unlocking of the door If the filling door can no longer be opened it can be opened with the aid of the emergency unlocking facility N Warning Switch off the washing machine before operating the emer gency unlocking and remove the plug from the mains ts 1 If water is visible in the door s window first perform emergency empty ing see the section Carrying out emergency emptying 2 Open the flap downwards in the right part of the base panel 3 Turn the rotary knob clockwise using a coin The filling door springs open 39 Operating Instructions 40 Additional Rinse RINSE The washing machine is set for very economical water consumption However for persons who suffer from allergies to detergents it can be helpful to rinse with extra water If this function is set an additional rinse cycle is carried out for the COTTONS LINEN EASY CARES EASY IRON and DELICATES programmes When the appliance is supplied from the factory the additional rinse function is not set Setting the additional rinse function Turn the programme selector to SHORT SPIN Press the SENSITIVE button for at least 5 seconds After the button has been pressed for 5 sec
42. r appliance needs repairing please contact customer service or your dealer Never put the washing machine into operation if the mains cable is damaged or if the control panel work top or base area is damaged in such a way that the inside of the appliance is openly accessible Before cleaning care and maintenance work switch off the washing machine Also pull the mains plug out of the socket or in the case of permanent connection switch off the LS switch in the fuse box or completely unscrew the screw in fuse e f operation is stopped disconnect the appliance from the mains sup ply and shut off the tap Never pull the mains plug out of the socket by the cable Always use the plug Multiple connectors couplings and extension cables must not be used Fire hazard through overheating Do not spray down the washing machine with a water jet Danger of electrical shock e The glass in the filling door become hot when high temperature washing programmes are used Do not touch Operating Instructions Allow the washing solution to cool down before performing and emergency emptying of the appliance before cleaning the solution pump or before an emergency opening of the filling door Small animals can chew on power cables and water hoses This can cause a danger of electric shock and water damage Keep small animals away from washing machines We Disposal Disposing of the Packaging Material Dispose of the
43. reasons DOOR LIGHT display is off The programme security function is On Remedy Close the water tap remove the mains plug and inform your local Service Force Cen tre Clean the detergent dis penser drawer and attach the conditioner insert correctly Pay attention to the maxi mum load quantity see pro gramme tables In the case of easy care fabrics select the EASY IRON programme Always load the drum as ful as possible with a combina tion of large and small items Remove the kink Contact your local Service Force Centre For pumping heights over 1 m a conver sion kit is available as a spe cial accessory Switch off appliance and pull out the mains plug Clean the drain pump Clean siphon Wait until the DOOR LIGHT display lights up green Cancel programme security see section Programme protection Operating Instructions Problem Remnants of detergent are building up in the detergent drawer The rinse water is cloudy When pressing a pro gramme option button the corresponding dis play does not light up Programme cycledis play flashes constantly Possible cause Water tap is not fully opened The inlet hose filter in the coupling of the inlet hose at the tap is blocked The cause is probably a de tergent with a high silicate content The selected programme op tion cannot be combined with the set programme Programme security is switched On the pr
44. res 54 diio d T 58 Operating Instructions Operating Instructions N Safety The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law However as manufacturers we regard it as our responsibility to inform you about the following safety instructions Before Using for the First Time Refer to the Installation and Connection Instructions further on in this user information e f units are delivered in the winter months at minus temperatures Store the washing machine at room temperature for a few hours be fore putting it into operation Correct Use e The washing machine is only intended for washing normal domestic washing If the appliance is used for a wrong purpose or wrongly op erated the manufacturer cannot assume any liability for any dam ages Additions or modifications to the washing machine are strictly for bidden due to safety reasons Use only detergent which is suitable for washing machines Refer to the detergent manufacturer s instructions he washing must not contain any flammable solvents Also bear this in mind when washing pre cleaned washing Do not use the washing machine for dry cleaning e Dyes dye removing agents may only be used in the washing machine if the manufacturer expressly permits use of these products We can not accept liability for any damage e Use only w
45. safe keeping Close the 2 large holes with the caps B Important When fitting the plastic caps press until they snap into the rear panel securely 47 Installation and connection instructions 48 Prepare the installation place e The installation surface must be clean and dry free of floor polish residues and other greasy coatings so that the unit does not slip away Do not use lubricants as a sliding aid Installation on a high veil carpet or floor tiles with soft sponge backs is not recommended because the standing safety of the appliance is then no longer ensured e By installation surfaces with small format tiles lay a conventional rubber mat underneath Minor unevenness of the floor surface should never be levelled out by laying pieces of wood card or similar materials but rather should al ways be compensated for by adjusting the screw feet e f for space reasons it is not possible to avoid setting up the unit di rectly next to a gas or coal fired cooker install a thermal insulation panel between the cooker and washing machine 85 x 57cm which must have an aluminium film on the side against the cooker e The washing machine must not be set up in a room where there is a danger of frost Frost hazard e Flexible feed and drain tubings may not be crinkled or squeezed Installation on a concrete base If the unit is set up on a concrete base for safety rea
46. sconnect Water is not entering Filer im tine eei oi Woe n hose from water tap remove ra let hose connection is Error code CL 1 ap filter and clean under blocked pears running water Water tap is blocked with Check the water tap and limescale or is faulty have it reaired if necessary Operating Instructions Problem Washing machine vi brates during operation or is unstable Excessive foaming dur ing the main wash Water leaks out of the washing machine Possible cause Transport packaging has not been removed The machine is not level There is very little washing in the drum e g only a dressing gown Water could not be fully pumped out before spinning because the drain hose is kinked or water pump is blocked Probably too much detergent has been used The screw Connection on the inlet hose is leaking Drainage hose is leaking The drain pump cover is not correctly close Washing is caught in the door The emergency emptying hose is not correctly closed or is leaking Remedy Remove transport packaging according to setting up and connection instructions Adjust the feet according to installation and connection instructions This does not affect the op eration of the machine Check the drain hose and re move any kink if necessary or clean the drain pump and if necessary remove foreign bodies from the pump hous ing If may be necessary to re duce th
47. sion of the programme ENERGY SAVING A wash programme at approx 60 C that is particularly economical on electricity and water for slightly to normally soiled cotton and linen washing cottons linen with an extended washing time Programme Option Buttons The programme option buttons are used to adapt PRE the programme to suit the degree of soiling of the wasu O C wash The additional PRE WASH and STAIN options are not needed for normally soiled washing The SENSITIVE different functions can be combined together de pending on the programme PU PRE WASH Pre wash Soaking Cold pre wash before the main wash cycle which TIME follows automatically The DELAY TIMER button SAVER changes Pre wash to warm soaking SENSITIVE Special extra programme function that gives an extra rinse along with better fabric care less drum movement This is ideal when frequent washes are necessary for example in cases of sensitive skin RINSE can still be selected as well STAIN For heavily soiled or stained washing In wash stain treatment prod ucts powder or tablets are washed in at the optimum time as the pro gramme progresses With the WOOL y Handwash setting the additional programme op tion buttons cannot be used Operating Instructions TIME SAVER Shortened wash programme for lightly soiled washing consisting of three stages with the COTTONS LINEN EASY CARES programme and two stages with the other progra
48. sons it is essential to fit stand plates in which the washing ma chine is adjusted The stand plates are available from Customer Service under the spare parts number 645 425 058 O Installation on vibrating floors Where the floor vibrates particularly in the case of wooden beam floors with pliable boards securely screw a water resistant wooden panel at least 15mm thick onto at least 2 floor planks If possible set up the unit in the corner of a room as the wooden floor is optimally re strained there and is therefore least likely to be subject to resonance vi brations Installation and connection instructions Compensate for floor unevenness T IS Set the three adjusted feet at the Automatic adjustment foot rear If necessary check the setting Automatic adjustment foot The rear left foot of your washing ma chine is designed as a spring leg This means that it guarantees that your unit will stand securely even at high spin speeds If nevertheless the washing machine is unstable during spinning please proceed as follows nominal value of 10 mm To do this use the supplied special spanner to remove the transport safeguard If the automatically adjusting foot does not reach the floor left manually for extending the regired dimension with a spirit level Caution Never use wood card or similar underlays to level
49. ssure 50 The water pressure must be at least 1 bar 10 N cm 0 1 Mpa max imum 10 bar 100 N cm 1 Mpa f more than 10 bar Connect a pressure reduction valve upstream e f less than 1 bar Unscrew the inlet hose on the unit side at the sole noid intake valve and remove the flow regulator to do this remove the filter with pointed pliers and take out the rubber washer behind Replace the filter Installation and connection instructions Water inflow Connect the hose with the angled connection to A pressure hose 1 5m in length is supplied If a longer inflow hose is required only a VDE approved complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible Hose sets in lengths of 2 2m 3 5m and 5m are available for washing machines without Aqua Control Hose sets in lengths of 2 0m 2 9m and 3 9 m are available for wash ing machines with Aqua Control Caution Never cut into pieces in order to extend the hoses Sealing rings are supplied either in the plastic nuts of the hose screw connection or in the enc Va losed pack Do not use other seals O the machine Caution Do not lay the infeed hose ver tically downwards Instead turn it to the right or left as shown in the diagram Tighten the hose connection only by hand Connect the hose with the straight connection to a water tap with a R 3 4 inch screw thread
50. the collecting vessel several times To do this close the emergency drainage hose temporarily with the plug 37 Operating Instructions 38 When the water is completely drained 6 Push the plug securely into the emergency drainage hose and turn it clockwise to secure it 7 Replace the emergency drainage hose in its holder 8 Put on the flap and close Drain pump AN IS The drain pump is maintenance free The cover of the drain pump must only opened in the event of a malfunction when no more water is be ing pumped out e g if the pump is blocked Before loading the machine please always ensure that there are no for eign objects left in the pockets or in between the items to be washed Paper clips nails etc which may find their way into the washing ma chine along with the washing will remain in the drain pump housing To restart the drain pump when it is blocked please proceed as follows Warning Switch off the washing machine and remove the mains plug before cleaning the drain pump First carry out an emergency emptying procedure see section Carrying out emergency emptying 2 Place a cloth on the floor in front of the cover of the drain pump 3 Unscrew the drain pump cover in an 4 Remove any foreign objects and fabric Residual water may run out anti clockwise direction and pull it out lint from the pump housing Operating Instructions 5 Re
51. the transport safeguard are removed and that the unit is splash protected see Removing transport safeguard Otherwise the units or neighbouring furniture can be damaged when spinning Always insert the plug into a correctly installed earthed socket n the case of permanent connection A permanent connection may only be made by an authorised specialist Before putting the machine into operation ensure that the mains voltage and current type shown on the unit s rating plate correspond with those at the place where the machine is being installed The fuse rating is also found on the rating plate e Should work be carried out on the water supply installations in order to allow the machine to be connected properly to the water supply this work must be carried out by an authorised installer e Should work be carried out on the mains supply in order to allow the machine to be connected properly to the electricity supply this work must be carried out by an authorised electrician e The mains lead may only be replaced by the customer service or by an authorised electrician 45 Installation and connection instructions under units Transporting the appliance wet damage it stroyed Remove transport packaging Important It is essential to re move the transport packaging be fore putting the appliance into operation Keep all parts of the transport packaging in a safe place for future use Open both hose ho
52. ting Instructions Unit description Front view Drawer for de tergent and conditioner Control panel Rating plate Screw feet height adjustable rear left Automatic adjustment foot Drawer for detergent and care agent Stain removers Main wash detergent powder form and possibly water softener behind filling door Filling door Flap in front of the drain pump Pre wash detergent soaking agent or water softener Liquid care agents conditioner finisher starch Operating Instructions 10 Control Panel Spin speed Program RINSE HOLD button Progress Display Additional Programme Options DOOR LIGHT button Programme Selector Xj ENERGY SAVING OFF COTTONS UNEN i Ne o 1600 O DOOR PRE WASH O o EASY CARES EASY IRON z 1200 MAIN WASH PEA 0 1000 O START RINSE O gt 250 SENSITIVE O pause O FASHION 40 800 RINSE O SIK Y 30 400 WASH SPIN O COLD 20 J s e Ane RINSE HOLD O O me ENDO woo amp Y NG STARCHING P a N NE DRAIN Ae Q DELAY e OVER DOSING 20 SPIN 1 DELICATES JL SHORT SPIN Multi display START PAUSE Button DELAY TIMER Button OVERDOSING indicator Programme Selector The programme selector defines the ENERGY SAVING OFF nature of the wash cycle e g water o level drum movement num
53. type of washing see Programme tables COTTONS LINEN EASY CARES 95 temperature BEE In the multi display the FASHION probable duration of the set pro SILK Y grammes will be shown in Y comp minutes 30 SIARCHING WOOL g V NL DRAIN 30 40 Ven DELICATES SHORT SPIN If necessary press additional programme button s PRE The display of the selected additional programme is wash O displayed For changing to another selection press another SENSITIVE O button For resetting press button again STAIN O Operating Instructions Changing Spin Speed selecting RINSE HOLD IS To change Spin Speed for the final spin if neces sary select RINSE HOLD 1600 Press the Spin Speed RINSE HOLD button as often 1200 O as necessary until the indicator light for the de 1000 sired speed or RINSE HOLD is lit 800 If RINSE HOLD is selected the washing is left to 400 soak in the last rinse water without spinning RINSE HOLD O If the Spin Speed is not changed the final spin is automatically ad justed to suit the washing programme COTTONS LINEN EASY CARES 1600 revolutions per minute ENERGY SAVING 1600 revolutions per minute DELICATES 1200 revolutions per minute WOOL S Handwash 1200 revolutions per minute SILK y Handwash 1200 revolutions per minute FASHION 1200 revolutions per minute EASY IRON 1200 revolutions per m
Download Pdf Manuals
Related Search