Ｉｎｔｅｒｎａｌ 7/6 in 1 Ｄｒｉｖｅ 3 Users Manual
Contents
1. 2 Drive icons of the card reader are not displayed Check followings 2 1 Make sure the USB cable is connected properly Note The assignment of the pins needs to correspond with the motherboard 2 2 If your are using Windows 2000 SP3 or later check the Device Manager information 1 Check USB Mass Storage Device in the Universal Serial Bus controller If there is no warning it should be working properly 2 If steps in 1 can t be followed try the connection of the YD 8VO7 to the other USB connector if available 3 If drive icons do not appear even though the steps in 1 are followed the assignment of the logical drive may be conflicted or the logical drive may be disabled To check it run Computer Management program as following steps 3 1 Open Control Panel 3 2 Open Administrative Tools If you can t find Administrative Tools click Performance and Maintenance at first 3 3 Start Computer Management 3 4 Select Storage Disk Management 3 5 You can find removable drives in the bottom right window If your problem is the assignment of the drive letter you can change it here 4 The drive icon may also be hidden if any network drives are assigned as the same letters of the card reader s Check the drive letters if you use network drives 5 Proceed to next step 3 if above steps do not solve your problem Page 21 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 R2. aic ex asaiatuc Rea diealediealsdinal cionteit e eteten 23 10 3 Environment Specifications ccccccesccccsseeeceseeeceeeeeceeeeceueessuseesseaeessuseessseessagees 24 10 4 Cable Specifications lsseessseessesessseeee nennen nnn nnns 24 10 5 Pin Assignment ccccceececceececcsececcueeeccusceceseecseeessaseessaseessageessaseessaseessaseesnaess 25 DLP UNG TVG EOS Mee T 26 Page 3 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 1 About this manual This manual is intended for users who specialize in the assembly of build to order BTO PCs If you are an end user give great attention to the following items when using this product and manual Thoroughly read the manuals of your PC and its motherboard Before mounting the product in your PC be sure to turn off the power to the PC and remove the PC s power cord from the wall outlet Recent PCs remain internally live even after shutting down Windows When connecting the USB cable supplied with this product to the motherboard first read the manual for your motherboard to learn the position and pin configuration of the USB connector If you don t have your motherboard manual please find a copy of it on the website of the company that manufactured the motherboard Connecting the USB cable to a non USB connector or to a wrong USB connector position may result in a serious breakdown of not only this product but also
3. unplug the individual wires and reinsert them according to the pin configuration of the motherboard In case of using a USB A connecto o pin A cable USB A connector 5 pin connector Page 10 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 2 If you are using a YD 8VO7 you also need to connect the FDD power cable Plug the FDD power connector of the PC into the YD 8VO07 power connector NOTE Pay attention to the direction of installation Improper connection may causes damage or fire 3 If you are using a YD 8V07 you also need to connect the FDD interface cable Align pin no 1 of the PC FDD 34 pin connector with that of the YD 8V07 FDD I F connector Then plug the FDD 34 pin connector of the PC into the YD 8V07 FDD I F connector NOTE Pay attention to the direction of installation If improper connection is made the product will not operate correctly FDD power connector FDD I F connector Connector and cable diagram Internal 7 in 1 Drive 3 YD 8V07 QALY RN QV NU USB cable USB A connector 5 pin connector USB mini B connector USB cable USB A connector 5 pin connector Page 11 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 5 Before use If the Internal Drive 3 has been mounted in the PC before the installation of OS On Windows 98SE the memory card drive is recognized as other device and does not work but the
4. Internal Drive 3 into the drive bay of your PC 3 Align the screw holes on the sides of the Internal Drive 3 with the PC side mounting holes 4 Secure the Internal Drive 3 with four P TITE 3 x 5mm long screws If you use screws longer than 5 mm they may interfere with the inner parts of this product and it may cause a problem Please use the screws included in this package e Tightening torque 29 4cN m 3kgf cm e Recommended screw length P TITE 3 x 5mm long screws It is assumed that the PC side bracket is 0 5 to 1 mm thick Screw in depth on the Internal Drive 3 side MAX 5mm Page 9 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 4 3 How to connect the cables 1 Plug the 5 pin connector of the USB cable the interface s internal cable into the USB terminal on the motherboard Check your motherboard user manual for the location of the USB terminal If it is difficult to connect the motherboard with the 5 pin connector disconnect the 5 pin A cable and connect the USB A connector directly to a standard extemal USB port on your computer NOTE Pay attention to the direction of the connector See the reference illustration below In case of using a 5 pin connecto No 4 Black Ground Shield EN No 3 Green DATA No 2 White DATA B No 1 Red VCC scale Internal USB terminal N NOTE For the pin configuration refer to the motherboard user s manual When pin configuration differs
5. Memory Stick PRO The Memory Stick operates as a USB interface removable disk The Memory Stick Memory Stick PRO should be inserted into the Memory Stick slot located in the lower right hand part of the Internal Drive 3 When inserting the card push it in as far as it will go The card slot is designed as to avoid from insertion of wrong direction YD 8V07 YD 8V09 Memory Stick Page 15 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 7 2 4 Inserting a MultiMediaCard or SD Memory Card The MultiMediaCard and SD Memory Card operate as a USB interface removable disk The MultiMediaCard or SD Memory Card should be inserted into the SD Memory Card slot located in the upper right hand part of the Internal Drive 3 When inserting the card push it in as far as it will go The card slot is designed as to avoid from insertion of wrong direction MultiMediaCard or SD Memory Card Page 16 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 1 9 How to operate on Windows 1 Accessing to the Media Floppy Disk Memory Card etc FDD Access LED turns on during the access Memory Card Access LED blinks during FDD Access LED the access Memory Card Access LED YD 8V09 S O Access LED 2 Removing the Media Floppy Disk Memory Card etc e Removing a floppy disk YD 8V07 To remove the floppy disk make sure the access LED is turned off then press the Ej
6. Memory cards are not included and must be Purchased separately Page 8 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 4 How to attach 4 1 Handling notes Please keep the following in mind when handling the Internal Drive 3 e When handling the product gently grasp the product along its sides near the attachment screw tap holes Grabbing the product anywhere else may cause the unit to bend or deform leading to breakdown and product failure e Securely mount both sides of the drive to the PC or drive bay frame using the supplied screws Attaching only one side may cause the drive to warp leading to drive failure e Please install the Internal Drive in a flat horizontal position with the CompactFlash card slot on the bottom e Before working inside the computer be sure to turn off the power to the PC and remove the PC s Power cord from the wall outlet Recent PCs remain internally live even after shutting down Windows Wait 5 seconds after removing the power cord from the wall outlet to prevent electrical shock and damage Take all action against static electricity before working inside the computer 4 2 How to mount the Internal Drive 3 1 Refer to the manual of your PC and the manual of the motherboard it should explain how to prepare a drive bay for installation of a new drive like the Internal Drive 3 NOTE When there is no 3 5 inch bay use a commercial 5 inch bay adapter 2 Insert the
7. Microsoft Windows is a registered trademark of Microsoft Corporation CompactFlash is a registered trademark of SanDisk Corporation SmartMedia is a registered trademark of Toshiba Corporation MultiMediaCard is a trademark of Infineon Technologies AG and licensed MultiMediaCard Association SD card Logo is a registered trademark SONY Memory Stick Memory Stick PRO MagicGate and are registered trademarks of SONY Corporation Y E Data is a registered trademark of Y E Data Inc Other company names and product names in this manual are trademarks or registered trademarks of their respective companies Page 2 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B Contents L ADOULEITIS UM ANN AY aks eee eraa a hate isse ete a aA E E sun eum pu ed iM T LL LR 4 2 ONEVIEW e uu MEUM NEUE MN ee a 4 3s Feat res Ofthe Internal DrIV8 9o uoo adco uoo eie 2d ao ona SEDES ee 5 D LoGompalible OSES eed a aa a a iut 5 34 COMPpalble Storage MEd aissis E iu b Sb dp SS cu M GNE 6 Sos un IM TTI c T SUUM m LOTION 10 ce dnd F ACKO COMOT summ ate nee re ere eine ete ree eee A 9 2 Imternato T3 T DEFIVe 9 adeo Dele tudo tus quis Mr ener on anne Unc en eterna cr me eer nner nnenine 8 atl EXICHOr 1CQUUICS c eee 8 Du Pdckdge COMEN ssi cm oes DU a aaaceacacaa A M EE aere 8 AM HOW to QULAGCIN pu P E 9 ANNI Iuejaedue m x 9 4 2 How to mount the Internal Drive 3 c cc ceccceccceseeceeee
8. and other protected file types with anti piracy functions are not supported I O cards such as GPS cards are not supported Memory Stick PRO DOS formatted memory sticks between 256 MB and 1 GB are supported MagicGate cards are supported but the Magic Gate feature is not supported so music data and other protected file types with anti piracy functions are not supported SD Memory Card DOS formatted memory cards between 8 MB and 512 MB are supported The Secure Digital feature is not supported so music data and other protected file types with anti piracy functions are not supported SD I O cards and SD Combo cards are not supported MultiMediaCard DOS formatted memory cards between 16 MB and 128 MB are supported Keitaide Music support cards are supported but the Keitaide Music feature UDAC MB protocol is not supported so music data and other protected file types with anti piracy functions are not supported The read write speed of MultiMediaCard is much slower than other cards It comes from the specifications of the cards NOTE 1 In this manual the above seven types of media except floppy disk are generically called memory cards 2 When using a Microdrive do not use other memory cards at the same time because of the Microdrive s large power consumption 3 MultiMediaCards and SD Memory Cards use the same slot so you cannot use them at the same time 4 Memory Sticks and Memory Stick PROs use the same slot so yo
9. other equipment and the PC Within this manual each product is distinguished using the following term Internal 7 in 1 Drive 3 is henceforth called YD 8V07 Internal 6 in 1 Drive 3 is henceforth called YD 8V09 YD 8V07 and YD 8VO9 are henceforth called Internal Drive 3 2 Overview 1 The Internal Drive 3 is the built in unit of Desktop PC 2 The YD 8V09 contains USB Universal Serial Bus compliant card reader writers for CompactFlash Microdrive SmartMedia Memory Stick Memory Stick PRO SD Memory Card and MultiMediaCard cards The card reader writers are to be connected to the USB port of the PC 3 The YD 8VO is a combo product of a 3 5 inch floppy disk drive and USB compliant card reader writers The floppy disk drive is connected to the floppy disk controller built in your PC The card reader writers are connected to the USB port of the PC 4 The Internal Drive 3 is compatible with the Hi Speed USB If Internal Drive 3 is connected to the personal computer s Hi Speed USB port the Internal Drive 3 can accessed at a transmission speed of up to 480Mbps If Internal Drive 3 is connected to the personal computer with Full Speed USB port it can access at the transmission speed of up to 12Mbps 5 To use the Internal Drive 3 the following requirements must be met the PC is equipped with a USB port the OS installed on the PC supports USB and the driver software the Internal Drive 3 is installed on the PC
10. CompactFlash Microdrive SmartMedia Memory Stick Memory Stick PRO SD Memory Card MultiMediaCard Reader Writer Floppy Disk Drive Internal 7 in 1 Drive 3 Model YD 8V07 Internal 6 in 1 Drive 3 Model YD 8V09 User s Manual This product and manual are intended for persons who have expert knowledge about personal computer PC Before connecting the product to your PC read the manuals of your PC and its motherboard carefully If you have any question contact the store from which you purchased the product YW Y E DATA www yedata com lt PN 149511 02 Rev B gt Copyright 2004 Y E Data Inc All Rights Reserved August 2004 sir Memory STICK Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B Before installing the Internal 7 6 in 1 Drive 3 into your PC read through this manual The driver software may have to be installed in advance B Before turning the power to your PC on or off remove all media from the product Caution B This product is a precision device So do not drop the product shake or strike it or install it in locations exposed to heavy vibrations or high temperatures doing so may cause the product breakdown Do not disassemble or modify the product Disassembly or modification may cause a breakdown fire or electric shock Do not use or store the product in wet locations The moisture may 2i result in a breakdown fire or electric shock Prohibition Do n
11. Page 4 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 3 Features of the Internal Drive 3 Internal 7 in 1 Drive 3 YD 8V07 1 The YD 8V07 contains a low profile floppy disk drive The YD 8V07 can be installed in the space occupied by a conventional 3 5 inch floppy disk drive NOTE Since the positions of an attachment screw may differ depending on PC make reference to the manual of PC 2 The YD 8V07 supports 3 5 inch floppy disks of 1 44MB or 720KB format Internal 6 in 1 Drive 3 YD 8V09 1 The YD 8V09 can be installed in the space occupied by a conventional 3 5 inch floppy disk drive NOTE Since the positions of an attachment screw may differ depending on PC make reference to the manual of PC Common features of the YD 8V07 and the YD 8V09 1 The Internal Drive 3 can be used in many environments Windows XP Windows 2000 Windows Me and Windows 98 Second Edition 3 1 Compatible OSes Windows Windows XP This product works with the standard driver in product works with the standard driver in Windows Install the driver from the CD ROM to use this product with the special drive labels Windows 2000 Install the driver from the CD ROM after installing Windows 2000 Service Pack 3 or greater Windows Me This product works with the standard driver in Windows Install the driver from the CD ROM to use this product with the special drive labels Windows 98 Second Edition Install the driv
12. ceeeceececaueeseusceseeseueeseusesseesnaees 9 4 3 How to connect the Cables cemara a a a EE E 10 D IBESIOIO USO cir IM I DE EM E MEUM E EC EI 12 6 HOWTO install the driver iii UT 13 6 1 How to install driver software seeesseesesssssseeeeeeene nennen nnne nnns 13 6 2 Icon and Corresponding Memory Cald cccccseeccccseeeecseeeeeeeeeeeeeseeeessegeeesseeeeeseeees 13 7 How to operate the Internal Drive 3 eesseeeesee eere eere nnne 14 7 1 How to operate the floppy disk drive seeeeseeeseeeeeeeeeenn 14 TNS a elioby d dU sectetut vmm vnnd rbd veri vane eter cee ne 14 7 2 1 Inserting a CompactFlash card or Microdrive 11ccccceccevececnsescsescnsenseeseaeesenees 14 4 2 2 Inserting a SmartMedia Cal sraa a E tnt etta ut cic tu apa vua a ausa am 15 7 2 8 Inserting a Memory Stick Memory Stick PRO cccssccccssseeeessseseesseeeessaneneeees 15 7 2 4 Inserting a MultiMediaCard or SD Memory Card esses 16 7 3 How to operate on Windows sseessseeseseeseeeeeeee nennen nenne nenne nnne nnn nnn rn 17 B ROSITICIOTS 2i oin pain MED D M dA D LU LL Le at ada 19 J ITOUDIESHO ONN ue mE eR MA 21 10O Product sDecilic ATION usos um undue ue I I uu UU I eee 23 IO T Physical Specifications ecadedentidetcdentadeabaglt iani d ame ema dise deme datus dita date done Same date deine 23 10 2 Electrical SpeclifiCallOlis
13. ect button to remove FDD Access LED Page 17 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B Removing a memory card Make sure that a file on the media is not being used by an application or being copied before removing the media If you remove the media during access the blue screen may be shown or the data on the media may be destroyed To avoid accident remove cards as follows 1 In my computer right click the appropriate drive icon 2 Left click Eject on the context menu that appears 3 Wait until LED stops blink It is recommended to wait 30 seconds or more for delayed write 4 Pull out the memory card with your fingers 4 Pull out memory card Open lt lt Explore YD 8V09 ilias Search e Sharing and Security gt AA Cut Copy B 1 Right click 2 Left click 3 Wait for access LED to turn off Create Share Rename Properties Important On Windows XP and 2000 the card may be accessed by a delayed write operation after the access LED stops blink For safety purposes wait 30 seconds or more after the access LED stops the blink then remove the media Page 18 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 8 Restrictions 1 Precautions for use on Windows XP 2000 and Me Windows XP 2000 and Me show the removal icon on the task tray but you should not use this icon If you disconnect the Inter
14. er software from the CD ROM NOTE Installation of the driver software before Windows2000 Service Pack 2 is possible However to use in the optimal environment we recommend to install Windows 2000 SP 3 or greater After Windows 2000 SP 3 or greater is installed please install the driver software from the attached CD ROM again Page 5 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 3 2 Compatible storage media Compatible media supported DOS formatted memory cards are supported I O cards such as modem LAN and PHS cards are not supported Microdrive DOS formatted memory cards are supported We have checked the operation of Type II Microdrives of up to 1 GB When using a Microdrive remove other memory cards The Microdrive requires more power than other memory cards If you use it with other memory cards at the same time an error may occur due to a shortage of power omartMedia DOS formatted memory cards between 4 MB and 128 MB are supported Only 3 3 V cards including those marked as 3 V are supported 5 V cards are not supported You can use SmartMedia cards with an ID but the ID feature is not supported Music data and other protected file types with anti piracy functions are not supported ROM cards are not supported Memory Stick DOS formatted memory sticks between 4 MB and 128 MB are supported MagicGate cards white are supported but the MagicGate feature is not supported so music data
15. ev B 3 Custom Icons for the YD 8V07 are not displayed Check following items 3 1 If you have installed custom icon driver for the card reader of other brand uninstall it if possible Or if the upgraded one is available try the upgrade 3 2 Try following sequence to refresh the driver software if you have installed other removable storage devices or you have used network drives 1 On the device manager program double click Universal Serial Bus controller item to view the individual items Next double click USB Mass Storage Device item to open the property window then disable the item using popup menu placed on the bottom side of the window 2 Restart your PC 3 Enable the USB Mass Storage device again on the device manager in order to reinstall the device driver 4 Floppy Disk Drive FDD does not work Check following items 4 1 First of all make sure the drive icon of the floppy is displayed in the My Computer window normally If the icon is not found make sure that the floppy related BIOS settings e g the type of the drive is set to 3 5 1 44M the Floppy Disk controller is enabled and so on Regarding the setting of the BIOS refer to the manual of your PC because the setting items are depend on the PC 4 2 If the LED of the FDD is constantly on the 34 pins interface cable has probably been connected upside down Check the connecting direction Note That inserted floppy diskettes may be damaged dur
16. ew hardware After installation open My Computer you should see four new icons as shown in the following table The assigned drive letters E F etc depend on your PC Note If you install the driver software after attaching Internal Drive 3 to the PC a generic removable disk icon may be displayed In this case push the F5 key or shutdown and restart the PC Then the icons will be displayed correctly 2 If one icon is selected and double clicked the files on the memory card will be displayed and can be accessed Icon Windows XP Windows 2000 Without SP Me 98SE 9 S Compact Flash Drive E 7 F Corresponding Memory Card CompactFlash Microdrive n SmartMedia E er Memory Stick Sw Memory stick Drive Memory Stick PRO a SD Memory Card Sg PD Card Drive MultiMediaCard Smart Media Drive Page 13 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 7 How to operate the Internal Drive 3 1 1 How to operate the floppy disk drive The YD 8VO7 s floppy disk drive is a standard 3 5 inch floppy disk drive so it can be operated in the same manner as a standard floppy disk drive 1 Inserting a floppy disk The floppy disk should be inserted into the floppy disk slot located in the upper part of the YD 8VO7 When inserting the floppy disk push it in as far as it will go When the floppy disk is inserted correctly Eject button for unloading pops out Floppy disk Eject bu
17. ing a Microdrive 3 For use with Limited power source Page 23 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 10 3 Environment Specifications Relative Humidity 30 80 RH Vibration oweep Time 5 6 minutes Test time 10 minutes each direction Direction of Sweep XYY Shock Direction of Shock XYY 10 4 Cable Specifications Description USB Cable Connected USB Cable Attached 9 8 m s 10 200 Hz 1 0G 19 6 m s 10 to 500 Hz 2 0G 4 9 m s 200 500 Hz 0 5G 49 m s 11 ms Half Sine 5 0 G 980 m s 11ms Half Sine 100G opecification Connector Cable Color length Type mini B Type A receptacle to opin connector Housing RE 05 JST or 10 cm Black Equivalent Terminal RF SC2210 JST or Equivalent Page 24 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 10 5 Pin Assignment USB Cable Connected Ground Black Plug Shell shield Plug Shell USB Cable Attached USB Type A receptacle LeadWire Wire 5 Pin Connector CONEA NG Plug Shell Shield E s No 3 Green DATA No 4 Black Ground Shield n No 2 White DATA No 1 Red VCC Fere Important Before connecting make sure the pin configuration corresponds with that on the PC consult the manual for your PC Page 25 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 11 About inq
18. ing the above condition even if the write protection of the diskettes are enabled In the worst case the motherboard may also be damaged 4 3 If accessing the drive does not turn the LED of the FDD on the power cable or the interface cable may not be connected properly Make sure the connection Note that wrong connection may break motherboard 4 4 If the problem continues it is good idea to connect another standard 3 5 1 44M FDD to confirm that the computer is working order and to determine that it is the YD 8V07 and not the computer is not functioning properly Page 22 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 10 Product specification 10 1 Physical Specifications oize Excluding 101 6x0 5 mm w X 25 4 0 5 mm H X 154 5 1 mm D protrusion Drive Unit Weight YD 8V07 285 g TYP YD 8VO09 115 g TYP 10 2 Electrical Specifications Description opecification i FDD only YD 8V07 USB Card Reader USB spec REV 2 0 USB Specification 34 Pin Standard Full Speed 12Mbps Hi Speed 480Mbps Power Supply Voltage DC 4 75V to 5 25V DC 4 75 V to 5 25 V Current Consumption 830 mA Max 500 mA Max Regulations UL cUL CE FCC Class B VCCI Class B Geen edor Yellow color Access LED i p Usually lights on and lights on during access 4 blinks during access 1 Test Condition Power Supply Voltage is DC 5 0 V and the floppy disk is general one 2 Except a case of us
19. installation of the driver software solves the problem On Windows XP 2000 and Me removable disk icons are displayed e When mounting the Internal Drive 3 to the PC that already has the installed OS install driver software for the internal Drive 3 before the mounting it If the Internal Drive 3 hardware is mounted before the installation of the driver software for the Internal Drive 3 and the hardware wizard appears be sure to cancel the wizard and then start up the installer e The floppy disk drive works with the OS standard driver so it is unnecessary to install driver software for the FDD Important If an earlier version of the driver software for our USB Memory Card Reader Writer is installed uninstall it before installing the Internal Drive 3 driver To uninstall the driver software refer to USB Card Reader Installer Users Guide Page 12 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 6 How to install the driver 6 1 How to install driver software The driver CD ROM contains software for Windows XP 2000 Me and 98SE Insert the driver CD ROM into the PC The installer will automatically start up The Installer recognizes the OS version and installs the appropriate software See USB Card Reader Installer Users Guide about the method of installation 6 2 Icon and Corresponding Memory Card 1 Windows automatically recognizes Internal Drive 3 and will perform the addition of n
20. loppy disk drive When setting the PC s BIOS set the floppy disk drive to legacy 3 5 inch 1 44 MB Some PCs provide 3 mode support in their BIOS However the YD 8V07 does not support the 3 mode Setting of 3 mode support may disable normal access to the drive under Windows Page 20 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 9 Troubleshooting 1 PC does not startup after the connection If your PC does not startup after the connection of the Internal Drive 3 the BIOS may be incompatible with the Internal Drive 3 Try following steps 1 1 Check web site of the PC or motherboard maker If update programs of the BIOS are available use it first 1 2 If latest BIOS doesn t solve the problem find Legacy USB Support item in the BIOS setting and if it is available disable it 1 3 If the motherboard has other USB port try to use the other one because it is known issue that reproduced on some motherboards of AOpen 1 4 Remove all memory cards from the slot of the Internal Drive 3 Some motherboards hang up if a CF card is in the card reader at the startup 1 5 Change the boot priority of the FDD lower than HDD 1 6 Change the boot priority of the HDD to top if step 1 5 could not solve the trouble 1 7 If the above have had no effect the remaining solution is replacing the USB cable with one which have ordinary USB A plug and put the plug into the connector of your PC on demand after the startup
21. nal Drive 3 the Internal Drive 3 cannot be used any more until Windows XP 2000 and Me is restarted Safely remove USE Mass Storage Device DrivestF G Hi I1 Open Explore Formatting of Media Search To format a floppy disk right click on the appropriate drive icon Sharing and Security in My Computer and select Format in the displayed menu Do not format initialize memory cards on Windows If you format E eae a memory card on Windows it may not be useable for devices Cut such as digital cameras due to the difference of the format type Copy FAT size cluster size hard disk type or super floppy disk type reste short If you have a digital camera format memory cards with your Rename camera Properties Standby The Internal Drive 3 supports the standby function based on the PC 2000 standard not all PCs standby function If the standby operation of your PC causes any problem do not use the function During standby do not insert or remove any media Supported SmartMedia card The Internal Drive 3 supports 3 3 volt and 3 volt SmartMedia cards not the old 5 volt type A 3 3V and 3V type oV type Important The Internal Drive 3 is designed so that the 5 volt SmartMedia card cannot be inserted Do not insert it by force Page 19 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B omartMedia card handling If the contact area of a SmartMedia card is dirty a read error ma
22. ot insert anything other than specified memory cards The insertion of a metal piece such as a coin or clip may lead to a breakdown fire or electric shock Do not remove the media from the product when its access LED lamp Is blinking This product is intended for use in general electric equipment Do not use it in equipment aerospace equipment atomic power control system traffic related equipment transportation equipment industrial robot combustion equipment various safety devices life support system etc that require special quality and reliability or that may threaten life or cause injury to the human body It is prohibited by copyright law to reproduce in whole or in part this software and User s Manual or rent the software without permission of the copyright holder We bear no liability for any pecuniary losses and lost profits resulting from use of the software included with this product and any claims from third parties This software cannot be used on other than specified equipment The specifications of this software are subject to change without notice We assume no responsibility for any breakdown and damage caused by misuse troubles from other equipment undue repairs or modifications If this product should have any defect attributable to manufacture we will exchange it with a new one but cannot take on any more responsibility Illustrative pictures in this manual may differ from the PC s actual screens
23. tton When a floppy disk is inserted the button pops out 1 2 Inserting a memory card 7 2 1 Inserting a CompactFlash card or Microdrive The CompactFlash card and Microdrive operate as an USB interface removable disk The CompactFlash card or Mcirodrive should be inserted into the CompactFlash card slot located in the lower left hand part of the Internal Drive 3 When inserting the card push it in as far as it will go When the card is inserted correctly it protrudes about 8 mm The card slot is designed as to avoid from insertion of wrong direction YD 8V07 YD 8V09 mmm L CompactFlash or Microdrive Important If you insert the card upside down or sidways the drive may be damaged Turn up the surface with A sign which shows the insertion direction Page 14 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 1 2 2 Inserting a SmartMedia card The SmartMedia card operates as a USB interface removable disk The SmartMedia card should be inserted into the SmartMedia card slot located in the upper left hand part of the Internal Drive 3 When inserting the card push it in with the golden contact side down as far as it will go When the card is inserted correctly it protrudes about 5 mm The card slot is designed as to avoid from insertion of wrong direction YD 8V07 Golden contact a Notch A SmartMedia Important Insert with the golden contact down 7 2 3 Inserting a Memory Stick
24. u cannot use them at the same time Page 6 August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 3 9 Internal 7 in 1 Drive 3 3 3 1 Exterior features Connector for the FDD interface cable Slot to insert a floppy disk pA USB cable for 5 pin Tapped holes used to mount Internal Drive 3 to PC Connector Please use P TITE 3x5mm screws in package Slot to insert a SmartMedia card Slot to insert a SD Memory Card FDD Access LED Slot to insert a Memory Stick card s EA E eT a a A 1 oe prefs M T D i Slot to insert a CompactFlash card Memory Card Access LED Important For mounting on the PC consult the manuals supplied with your PC and its motherboard 3 3 2 Package Content Driver P TITE 3 x 5mm Internal 7 in 1 Drive 3 USB 5 Pin A Cable CD ROM SES X 4 pieces NOTE Diskette or memory cards are not included and must be purchased separately Page August 2004 Internal 7 6 in 1 Drive 3 User s Manual 149511 02 Rev B 3 4 Internal 6 in 1 Drive 3 3 4 1 Exterior features gf Slot to insert a SmartMedia card Slot to insert a SD Memory Card SY Slot to insert a CompactFlash card Slot to insert a Memory Stick card Important For mounting on the PC consult the manuals supplied with your PC and its motherboard 3 4 2 Package Content Internal 6 in 1 Drive 3 USB 5 Pin ACable Driver P TITE 3x 5mm CD ROM screws Pd e X 4 pieces NOTE
25. uiries Inquiries should be directed to the store from which you purchased the product or any store that is listed on the package The latest information and the most up to date version of the driver software can be found on the following web site Product information available at http www yedata com products cardreaders index shtml Download driver software from http www yedata com support Page 26 August 2004
26. y occur Keep the contact area clean Do not touch the gold contact area Do not twist or warp the card Protect the card from static electricity SmartMedia card with ID The Internal Drive 3 does not support the ID information of the SmartMedia card but allows you to use any SmartMedia card with an ID as a usual media Restrictions on DOS mode When in DOS mode the only the floppy disk drive can operate The card reader writers do not operate in DOS mode To use those reader writers start up Windows Antivirus software When memory resident antivirus software runs on your PC the PC may become unusually slow or hang up In this case uncheck the media of the Internal Drive 3 in the anti virus software Floppy disk drive interface cable The YD 8VO7 floppy disk drive interface should be connected to the floppy disk controller on the PC s motherboard using a 34 pin ribbon cable The 34 pin ribbon cable usually has two connectors for floppy disk drives Connect the YD 8V07 floppy disk drive to the connector of the end side for Drive A If you have a second floppy drive connect it to the middle connector for Drive B LIES Computer side Drive B Drive A Important Be careful that Pin 1 of the cable is connected to Pin 1 of the interface Usually there are marks such as a red line or A sign indicating the Pin 1 side of the 34 pin ribbon cable NOTE A 34 pin cable is not supplied with this product 10 BIOS settings for the f
Download Pdf Manuals
Related Search