TC1290MS User Manual
Contents
1. other apparatus including amplifiers that produce heat Do not leave in direct sunlight 10 WARNING Do not place any naked flame source such as lighted candles on any electrical apparatus 11 Connect to a suitable 230 240 50 Hz power supply only 12 Always unplug from the power source when any electrical apparatus is not in use 13 Do not abuse or damage a power cord If any power cord is damaged it must be replaced by the manufacturer its service agent or a similarly qualified person in order to avoid a hazard A replaceable cord must be replaced with an authorised replacement from an authorised service agent only 14 Only use attachments accessories specified by the manufacturer 15 Unplug this apparatus during lightening storms or when unused for long periods of time 16 Attention is drawn to the environmental aspects of disposing of any battery 17 Refer all servicing to qualified personnel Servicing is required when the apparatus has been damaged in any way such as when the power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 18 Do not attempt to service any double insulated apparatus Double insulated apparatus requires specialist servicing and knowledge to retain the safety of the apparatus 19 WARNING Do not use any electrical apparatus outdoors If any electrical apparatus2. right speaker and L terminals for the left speaker Flip down red or black 52 el terminal flap insert the speaker wire and release flap to lock the wire in place MAINS CONNECTION Make sure that all the components and speakers are correctly connected Check that the rated voltage of your units matches the voltage of your power supply 230V 240VAC 50Hz Plug the AC Plug into the AC outlet HEADPHONES Be sure that your headphones have a 3 5mm stereo plug with an impedance of 8 32 Ohms When the headphones are connected the speakers will automatically mute LISTENING TO THE RADIO Press the power button to switch on the unit Set the function selector to the RADIO position Select the wave band AM FM or FM ST by using the BAND selector Tune in your desired radio station by turning the Tuning knob Switch off by setting the function switch to the CD position or pressing the power button NOTE for best FM radio reception extend out the Fm antenna cord For AM reception a built in ferrite antenna receives the signals Adjust the reception quality by turning the entire unit When the FM stereo signals are too weak or there is too much background noise it is better to switch the band selector to FM mono position PLAYING A COMPACT DISC Set the function selector to CD Press the CD open button place a disc in the centre with the label side up and close the CD door gently The total number of tracks available will be sh
3. C BOLT CD MICRO SYSTEM TC1290MS INSTRUCTION MANUAL IMPORTANT SAFETY INSTRUCTIONS When using any electrical apparatus always observe safety regulations and use basic safety precautions to reduce the risk of fire electric shock and personal injury including the following Read Keep and Follow these instructions heeding all Warnings 2 Keep out of reach of young children This apparatus is not suitable for use by young children or infirm persons without supervision Young children must be supervised to ensure that they do not play with the apparatus 3 WARNING Do not insert any objects into any openings of an electrical apparatus 4 WARNING Do not touch any moving parts of any electrical apparatus 5 WARNING Do not use this apparatus near water To avoid the risk of fire or electric shock do not expose this apparatus to rain or moisture The apparatus shall not be exposed to dripping or splashes 6 WARNING No objects filled with liquid such as vases shall be placed on any electrical apparatus Do not immerse in any liquid whilst in use or in cleaning Clean only with a damp cloth dry with a dry towel Do not use harsh abrasives as these may damage plastic parts 8 DONOT block any ventilation openings Install in accordance with the manufacturer s instructions Always allow a sufficient gap around the apparatus to avoid overheating 9 DO NOT install near any heat sources such as radiators gas heaters stoves or
4. is to be used outdoors use a suitable Isolating transformer or Electrical Safety Switch RCD 20 For household use only this apparatus is not intended for commercial use 21 If this apparatus is to be used by a third party please supply these instructions with it 22 No liability will be accepted for any personal injury or damage caused by failure to follow these instructions WARNING CLASS 1 LASER PRODUCT CAUTION INVISIBLE LASER RADIATION WHEN CLASS 1 LASER PRODUCT OPEN AND INTERLOCKS DEFEATED AVOID EXPOSURE TO BEAM This product contains a low power laser device CONTROLS CD skip search down button CD play pause button Volume max min CD program button CD repeat repeat playback button Power on indicator CD LED display track number CD Radio function switch CD compartment 10 FM ST FM AM Band switch 11 Open press to open the CD compartment 12 FM Stereo indicator 13 Power on off 14 X BASS Bass booster on off 15 FM AM band scale 16 Tuning knob for channel selection 17 CD Skip search up button 18 CD Stop button 19 Loud speaker terminals R right 20 Loud speaker terminals L left 21 FM antenna 22 Phones Headphone plug 23 Power cable CONNECTING SPEAKERS Connect the speakers to the red and black terminals on the back of the unit as shown Use the R terminals for the
5. own in the display Pressing the PLAY button after inserting a CD will start the first track playing To pause the track press the PLAY PAUSE button while the track is playing To return to normal playback press the PLAY PAUSE button once more To stop the CD playing press the STOP button SELECTING A DESIRED TRACK IN STOP MODE Press SKIP SEARCH Up or Down until the desired track number appears on the LED display Press PLAY PAUSE to begin playing that selected track The selected track number will appear on the LED display You can skip forward to another track by pressing the SKIP Up button The tracks will skip forward once each time the button SKIP button is pressed Pressing the SKIP Down button while in play mode will return you to the beginning of the track being played Pressing the button more than once will skip down a track each time it is pressed SEARCHING FOR A PASSAGE OF PLAY While the song is playing if you press and hold the SKIP Up Down button you can listen to the track at a high speed forward or backwards to find a particular passage of play The sound will be played faster than normal but at a reduced volume Play will return to normal when the SKIP up down button is released PROGRAMMING TRACKS You can program in up to 20 tracks in any desired order for programmed playback Set the FUNCTION switch to CD Press the PROGRAM button Press the SKIP Up Down button to select the track number that you wish
6. to program in Once you have selected the desired track number press the PROGRAM button Repeat steps 2 amp 4 to program in more tracks Once you have programmed in all the tracks you want press the PLAY PAUSE button to begin playback of the programmed tracks The playback will begin at the start of the first programmed track A stored program will be erased when the function switch is moved to the Radio position or the unit is turned off REPEAT MODE To repeat one or all tracks press the REPEAT button before or during playback Pressing the REPEAT button once will repeat the current track only pressing it twice will repeat the entire CD pressing three times will turn the repeat function off REPEATONE REPEATALL REPEAT OFF TECHNICAL SPECIFICATION e Power supply AC 230V 240V 50Hz e Receiving Bands AM FM stereo Tuning Range FM 88 108 MHz AM 540 1600 KHz e Speaker 4 Ohm 5W x 2 e Output Power 2 x 2W RMS 10 THD e Headphone Impedance 32 Ohm
Download Pdf Manuals
Related Search