English - Prexiso
Contents
1. Laser exit Battery status mum mp pp Cp Operations ota The safety instructions and the user manual should be read through carefully before the product is used for the first time The person responsible for the product must ensure that all users understand these directions and adhere to them The symbols used have the following meanings WARNING Indicates a potentially hazardous situation or an unintended use which if not avoided will result in death or serious injury CAUTION Indicates a potentially hazardous situation or an unintended use which if not avoided may result in minor injury and or appreciable material financial and environmental damage Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Operations retraite Note Measuring errors can occur when measuring to colourless liquids glass styrofoam or semi permeable surfaces or when aiming at high gloss surfaces Against dark surfaces the measuring time increases LASER ON E gt PREISO DO 2 485 m Operations act Operations ract Step back LASER OFF dm PREXISO 0 000m a 0 00 1 16 0 in 1 16 Enable Disable disclaimer Technical Data i Distance measurement Typic2. Impulse duration 0 2 x 10 s 0 8 x 10 s gt 1 4s N PREXISO iC4 OCES necio and 1040 1 aser 0 dated Juno 24 2007 wo 3427164 WO 318019 _ WO 0216964 EP 1195617 WO 0244756 US 5349501 mm Made in Austria Batteries 2x AAA Subject to change drawings descriptions and technical data without prior notice
3. WARNING Do not leave your device and its accessories within the reach of children or allow them to play with it They could hurt dazzle themselves or others or could accidentally damage the device Disposal AN CAUTION Flat batteries must not be disposed of with household waste Care for the environment and take them to the collection points provided in accordance with national or local regulations The product must not be disposed with household waste Dispose of the product appropriately in accordance with the national regulations in force in your country Adhere to the national and country specific regulations Product specific treatment and waste management can be downloaded from our homepage Electromagnetic Compatibility EMC ZN WARNING The device conforms to the most stringent requirements of the relevant standards and regulations Yet the possibility of causing interference in other devices cannot be totally excluded FCC statement applicable in U S This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable Ta protection against harmful interference in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications H
4. modification or conversion of the product e Use of accessories from other manufacturers without express approval e Deliberate dazzling of third parties also in the dark e nadequate safeguards at the surveying site e g when measuring on roads construction sites etc e Deliberate or irresponsible behaviour on scaffolding when using ladders when measuring near machines which are running or near parts of machines or installations which are unprotected e Aiming directly in the sun e This device is not designed for use by persons including children who have a restriced physical sensory or mental Capacity or persons who lack experience and knowledge of how to use this device lt PR Hazards in use WARNING Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified Carry out periodic test measurements Particularly after the instrument has been subject to abnormal use and before during and after important measurements ZN CAUTION Never attempt to repair the product yourself In case of damage contact a local dealer ZN WARNING Changes or modifications not expressly approved could void the user s authority to operate the equipment Limits of use Refer to section Technical data The device is designed for use in areas permanently habitable by humans Do not use the product in explosion hazardous areas or in aggressive environments
5. al Measuring Tolerance 3 mm 0 12 in Maximum Measuring 4mm 0 16 in Tolerance Typical Range 0 2 20 m 0 66 66 ft Smallest unit displayed 1 mm 1 16 in General Laser class 2 Laser type 635 nm lt 1 mW Battery durability 2 x AAA up to 3000 measurements Dimension H x D x W 107 x 57 x 35 mm 4 2 x 2 24 x 1 38 in Weight with batteries 90 g 3 53 oz Temperatur range Storage 25 70 C 13 158 F Operation 0 40 C 32 104 F applies for 100 target reflectivity white painted wall low background illumination 25 C applies for 10 to 500 target reflectivity high background illumination 0 C to 40 C Tolerances apply from 0 2 m to 10 m with a confidence level of 95 The maximum tolerance may deteriorate to 0 15 mm m between 10 m to 20 m Info Codes Code Meaning Help Info 252 Temperature too high Cool down iC4 connector Info 253 Temperature too low Warm up iC4 connector Info 255 Signal too low or distance Look for a better target out of range Info 256 Received signal too high Avoid high reflecting surfaces Info 257 Too high background light Protect target against sunlight and measure again Info 260 Laser beam interrupted Repeat measurement Other Errors Meaning Help Hardware Error The hardware could be Try again or contact damaged your dealer Communication Communication error Remove battery Error between iP
6. hone and iC4 lof iC4 and insert again Care Clean the device with a damp soft cloth Never immerse the device in water Never use aggressive cleaning agents or solvents Warranty The device has a one year warranty For further information on this contact your dealer Subject to change drawings descriptions and technical data O The person responsible for the instrument must ensure that all users understand these directions and adhere to them Areas of responsibility Responsibilities of the manufacturer of the original equipment Prexiso AG Europastrasse 27 8152 Glattbrugg Switzerland The company above is responsible for supplying the product including the User Manual in a completely safe condition The company above is not responsible for third party accessories Responsibilities of the person in charge of the instrument e To understand the safety instructions on the product and the instructions in the User Manual e To be familiar with local safety regulations relating to accident prevention e Always prevent access to the product by unauthorised personnel Permitted use e Measuring distances e Tilt measurement a Prohibited use e Using the product without instruction e Using outside the stated limits e Deactivation of safety systems and removal of explanatory and hazard labels e Opening of the equipment by using tools screwdrivers etc e Carrying out
7. owever there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help lt PR Laser classification Y a gt ne NY 8 Laser exit The device produces visible laser beams which are emitted from the instrument It is a Class 2 laser product in accordance with e EC60825 1 2007 Radiation safety of laser products Laser Class 2 products Do not stare into the laser beam or direct it towards other people unnecessarily Eye protection is normally afforded by aversion responses including the blink reflex ZN WARNING Looking directly into the beam with optical aids e g binocu lars telescopes can be hazardous Z CAUTION Looking into the laser beam may be hazardous to the eyes Laser Radiation Do not stare into the beam Laser class 2 acc IEC 60825 1 2007 Maximum radiant power lt 1mW Emitted wavelength 620 690nm Beam divergence 0 16 x 0 6 mrad
Download Pdf Manuals
Related Search