PROMOTION BOARD SK-86R12-01
Contents
1. 33 10 4 33 UZS MA HM HQ AE 33 10 4 1 Overview of possible Use Configurations sse 34 11 360 Wrap Around View WAV System eere 35 DEEST 41 12 1 Literature and References 56 41 1 55 42 FSEUGCC UM SK86R12 01 Rev1 4 6 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 1 Introduction 1 1 System Features This section provides an overview of the features of the SK 86R12 01 Emerald P Promotion Board 2x RS232 interfaces via FTDI USB serial converter USB to RS232 HOST SPI interface via FTDI USB serial converter USB to HOST SPI CAN interface Pin header 2 54 mm Media LB interface 3 pin Pin header 1 27 mm MOST interface connector for SMSC PHY Modules AIC IPC interface designed to work with Fujitsu ATLAS Calypso MCU boards DDR3 DRAM 2x 2GBit 512 MByte NOR Flash 16 bit or 32 bit usable 2 GBit NAND Flash 16 bit length 2 GBit Quad SPI Flash 128 MBit on board Ethernet internal MAC of Emerald used external PHY 10 100 MBit Configuration 1x USB Host JTAG debugger connector 38 pin Mictor Connector 20 pin 2 54 mm pitch adapter available SD card interf2. 4 ND a ta l Part Number Group Switch Switch Name Function Connected to the SELFL Select Flash pin of MB86R12 to select the memory to boot from please refer to the Boot Strap chapter of the MB86R12 Hardware Manual Note The boot flash device selected depends on the setting of SELFL and the MPXMODE 0 MPXMODE 1 DIP switches of SW10 SW15 System 1 SELFL SELFL 0 default MPXMODE 1 0 11 System boots from Serial flash MPXMODE 1 0 any other setting System boots from NOR flash SELFL 1 MPXMODET 1 0 11 Reserved MPXMODE 1 0 any other setting System boots from NAND flash 2 CRIPMO The combined state of these switches 3 CRIPM1 sets the initial value of the SSCG feedback divider ratio please refer to the 4 CRIPM2 section PLL Setting of the MB86R12 5 CRIPM3 Hardware Manual FSEUGCC UM SK86R12 01 Rev1 4 16 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 Configures the PLL bypass function please refer to the section PLL Bypass and PLL Operating Frequency of the MB86R12 Hardware Manual 0 PLL is not bypassed default 1 PLL is bypassed 6 PLLBYPASS Configures the initial value of the PLL clock frequency divider ratio please refer to the section PLL Operating Frequency of the MB86R12 Hardware Manual 7 PSMODE 0 533 MHz default 1 400 MHz Please read the imp
3. Fujitsu Semiconductor Europe FSEUGCC UM SK 86R12 01 Revi 4 User Manual EMERALD P PROMOTION BOARD SK 86R12 01 USER MANUAL co FUJITSU FUJITSU Emerald P Promotion Board SK 86R12 01 Hevision History Date Issue Rev1 4 Andy von Treuberg 15 10 2012 Added Note that Ethernet Interface is not usable in WAV configuration due to pin multiplexing Rev1 3 Andy von Treuberg 21 05 2012 Changed default settings of SW15 Changed references to schematic now Rev1 7 Rev1 2 Andy von Treuberg 08 05 2012 Complete rework of content Rev1 1 Herbert Honig ENDE Updated JTAG Settings Core Voltages Switches Rev1 0 Herbert H nig 02 02 2012 Added pictures 13 01 2012 Rev0 1 Herbert Honig First draft This document contains 42 pages FSEUGCC UM_SK86R12 01 Rev1 4 2 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 Trademarks APIX is a registered trademark of Inova Semiconductors GmbH Grafinger Str 26 81671 Munich Germany ARM is a registered trademark of ARM Limited in UK USA and Taiwan ARM M is a trademark of ARM Limited in Japan and Korea ARM Powered logo is a registered trademark of ARM Limited in Japan UK USA Korea and Taiwan PrimeCell amp is owned by ARM Limited CANG Controller Area Network are registered trademarks of Bosch Corporation in the United States and other countries I2C is a registered trademar
4. LEHE MININ r3 62 SO tu 5 5 6 g Ee Eh 2 g 16 DGNDL 19 22 28 30 E iu 5 E 3 Short pin description AlCxx_TDxx serial bus transmit direction AlCxx RDxx serial bus receive direction AlCxx_CLK serial bus clock GPIO to Interruptxx Atlas can use GPIOs to trigger interrupts on Emerald Emerald GPIO xx two GPIOs from Emerald that can be used outside SPIO xxxxx SPIO interface from Atlas SPI xxxxx SPI1 interface from Atlas Power Control Emerald soft start for Emerald board also see section 4 HIGH starts up the board FSEUGCC UM SK86R12 01 Rev1 4 ee 30 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 Required Pin Multiplexing Mode PinMuxGroup F MuxMode 2 is required to use the AIC IPC interface Please refer to page 27 of the board schematics for details FSEUGCC UM SK86R12 01 Rev1 4 31 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJITSU SK 86R12 01 9 Power Supply The SK86R12 01 Promotion Board requires an external power adapter to supply an input voltage in the range of 9V 18VDC The current consumption of the board in operation is approximately 1 5A The board generates various supply voltages 1V2 1V5 1V8 3V3 5V required to power the MB86R12 and interface devices on the baseboard The power supplies are designed to deliver a curre
5. x a EE Q z ce c ra cc 25 O O O O ar gt EE TE EM SC ME ez sB m uz PU C Maimam tly LEE ao LJ TT S mi me s EL Hio i 31b o in cg i ide ee Dae ae FSEUGCC UM_SK86R12 01 Rev1 4 39 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 Connectors Used Display Out 0 upper HDMI Connector MiniUSB for UARTO CAN Adapter cable connected to X16 Camera Connectors X25 X28 X29 X31 Cinch Connectors FSEUGCC UM SK86R12 01 Rev1 4 40 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 12 Appendix 12 1 Literature and References Used JEmerald P Promotion Board Schematics http www fujitsu com downloads MICRO fme displaycontrollers sch sk 86r12 01 rev1 5 pdf Datasheet SAA7113H Video Processor http www nxp com pip SAA7113H html Datasheet Wolfson WM8976 Sound Codec http www wolfsonmicro com products codecs WM8976 Datasheet TFP410PAP DVI Transmitter http www ti com lit ds symlink tfp4 10 pdf Datasheet External PHY DP83865DVH http www national com pf DP DP83865 html Datasheet Spansion QUAD SPI Flash S25FL129POXNF 100 http www spansion com Datasheet NAND Flash Micron MT29F2G16AADWP ET http download micron com pdf datasheets flash nand 2gb m29b pdf Fujitsu Developer Studio a great tool for register access http w
6. P Promotion Board is configured using a series of DIP switches The functionality of these groups of switches is described in the following sections 7 1 DIP Switch SW10 JTAG Pin Multiplex Mode Default Settings on ON logical 0 OFF logical 1 ML inn n unused unused unused MPXIVIODEO MPXIVIODE1 JTAG Select MPXIVIODEZ TEST MODE TE Part Number Group Switch Switch Name Function SW10 System 1 Unused leave OFF 2 Unused leave OFF 3 Unused leave OFF Connected to the JTAGSEL pin of MB86R12 4 JTAG Select 0 Normal Mode JTAG interface not in use default 1 DFT Design For Test Mode 5 MPXMODE 0 Connected to the MPXMODE 0 1 2 pins of MB86R12 The functionality of these 6 MPXMODE 1 pins is somewhat complex please refer to the section Pin Multiplexing of the 7 MPXMODE 2 MB86R12 Hardware Manual Default setting Mode 2 Reserved do not change 8 TEST MODE 0 Normal Mode default 1 Test Mode SW10 can be found on page 8 of the schematic Rev1 7 FSEUGCC UM SK86R12 01 Rev1 4 15 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 7 2 DIP Switch SW15 Boot Flash Selection PLL Exception Vectors Default Settings on ON logical 0 OFF logical 1 SELFL CRIPMO CRIPM1 CRIPM2 CRIPM3 PLLBYPASS PSMODE VINITHI lt 4Rh f 3 ALT
7. 7 must be set to ON to use this interface ENABLE SD CARD Required Pin Multiplexing Mode PinMuxGroup F MuxMode 0 is required to use the SD Card interface Please refer to page 25 of the board schematics for details FSEUGCC UM SK86R12 01 Rev1 4 29 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 8 10 Sound An external sound codec WM8976 is integrated on the SK86R12 01 Promotion Board and connects to the 1250 interface of the MB86R12 Emerald P The codec can be programmed via I2C Please check the device s datasheet for details see Appendix Required Pin Multiplexing Mode PinMuxGroup F MuxMode 0 or 4 is required to use the sound interface Connector X7 has LINE INPUT and LINE OUTPUT jackplug connections both are stereo Set switch 7 of SW7 to ON in order to use the sound interface ENABLE 250 SOUND Please refer to page 26 on the board schematics for details 8 11 AIC IPC to Atlas The SK86R12 01 Promotion Board was also designed for deveopment work with Fujitsu s MB9DF126 Atlas MCU device For details follow this link http mcu emea fujitsu com mcu product detail MB9DF 126PMC htm The AIC IPC Automotive Inter Connect Inter Process Connect interface of the SK86R12 01 Promotion Board is identical to that of the Atlas Starterkits but it can be used also with other MCUs The diagram below shows the pinning of connector X9 AIC IPC IL 6 n
8. New USB device strings Mfr 1 Product 2 SerialNumber 0 7 230000 usb Product ISP1520 7 7 7 e 240000 hub 1 0 USB hub found 240000 hub 1 0 3 ports detected to mount an usb memory device 1 1 1 1 230000 usb 1 1 Manufacturer Philips Semiconductors 1 1 1 1 Unabl start demonstration 16 960000 init module Apr 4 2012 11 41 20 16 960000 init module Mapped vram area 896000000 phys 90000000 size 256MB Resolution 800 x 600 Enter Close small big left tube right tube on off antialiasing on off motion blur on off show frames per second on off toggle engine mode hz Figure 4 1 Console output 7 i Pe 100 140 77 0 M 60 e e BAYERN 3 Figure 4 2 Running Demo FSEUGCC UM SK86R12 01 Rev1 4 12 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 5 About U Boot The U Boot utility is an embedded program that handles the basic configuration of the MB86R12 device boots the Linux operating system and provides a communication interface to the user Assuming the physical connection has been made from the PC USB interface to the SK86R12 01 USB and the board has been self installed creating a new virtual COM ports e g for communication the U Boot program presents itself to a user via a terminal program link which uses the third new virtual COM port may be named USB Serial Converter C To stop U Boot loading the demons
9. TSU Emerald P Promotion Board SK 86R12 01 8 2 4 Capturing Video ITU656 MB86R12 Emerald P has four ITU656 video capture units From a board design point of view connecting components used these are organized as two pairs Capture 0 and Capture 3 e Capture 1 and Capture 2 8 2 4 1 Capture Interface 0 and 3 The following table shows the connectors used on the board Connectors Used Capture Interface S Video Cinch Decoder 0 X24 X25 TVP5150AM1 Capture 0 IC 8 bit Write address OXBA E AED X28 Capture 3 0 8 bit Write address 8 Required Switch Settings SWE switch 1 ENABLE CAPTURE 0 ON SWE switch 4 ENABLE CAPTURE 3 ON 8 2 4 2 Capture Interface 1 and 2 The following table shows the connectors used on the board Connectors Used Capture Interface S Video Cinch Decoder 1 X32 X31 SAA7113H Capture 1 8 bit Write address 0x4A 2 pee X29 Capture 2 0 8 bit Write address 0x48 Required Switch Settings SWE switch 2 ENABLE CAPTURE 1 ON SWE switch 3 ENABLE CAPTURE 2 ON Required Pin Multiplexing Mode for all Video Capture units PinMuxGroups ZH l MuxMode 0 is required The TVP5150AM1 and SAA7113H decoders must be programmed correctly via 12C e g to select the input signal S Video or CVBS The board is supplied for use with S Video signals For CVBS input board must be modified components removed Pleas
10. ab For support and downloads concerning the SK 86R12 01 board please refer to the following locations http www fujitsu com emea services microelectronics gdc evalobds emerald p promotionboard html select the Support tab or http www fujitsu com emea services microelectronics gdc evalods wraparound starterkit html select the Support tab FSEUGCC UM SK86R12 01 Rev1 4 9 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJITSU SK 86R12 01 3 System Overview The Emerald P Promotion Board itself is a complete evaluation system but there are also two optional extras that can be used in conjunction with the Promotion Board to build a system for specific application development Emerald P Promotion Board SK 86R12 01 Optional extra SK 86R12 WAVO1 add on board for digital 360 wrap around view providing 4x digital camera support e Optional extra MOST add on Board SMSC PHY series Figure 3 1 System Overview The Emerald P Promotion Board is also a part of the 360 Wrap Around View product and is therefore also covered in this guide FSEUGCC UM SK86R12 01 Rev1 4 10 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 4 Quickstart Before powering up the board please ensure that you have a DC power supply that can deliver a voltage in the range 9 18V 12V recommended at max 1 5A The inner pin has to be connected to pos
11. ace 3x APIX TX interfaces 3 Gbit x APIX RX interface 3 Gbit 4x cinch YUV and 4x S Video connectors for video input HDMI video capture input RGB888 2x HDMI video output RGB888 x FFC video output RGB666 with touch controller for the direct connection of Glyn EDT display family devices 3x video output on pin header 1 27mm pitch RGB888 3x user buttons and 3x user LEDs programmable via GPIOs Sound line input line output Connector for SK 86R12 WAV01 add on board for digital 360 wrap around view cameras Most of the interfaces can be accessed separately via control switches on the board This makes it possible to use all the multiplex modes that MB86R12 Emerald P provides FSEUGCC UM SK86R12 01 Rev1 4 7 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 1 2 Mechanical Dimensions PCB components not mounted 200 x 150 mm Dimensions with mounted connectors 220 x 150 mm Height with spacing bolts 40 mm FSEUGCC UM SK86R12 01 Rev1 4 8 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 2 Information and Support on the Internet The functional details of the MB86R12 Emerald P device can be found in the latest Hardware Manual which can be downloaded from the following location http www fujitsu com emea services microelectronics gdc gdcdevices mb86r12 emerald p html select the Support t
12. ate 115 200 bps o Data 8bits o Stopbit 1 bit o Parity none o Flow Control none Connect the terminal program to port USB Serial Converter C Connect an HDMI cable to X1 use the upper HDMI port of the connector which is Display 0 Connect the other end of the cable to a TFT monitor that supports DVI and a resolution of 800 x 480 pixels virtually any modern TFT monitor will support this mode Connect the external DC power supply to X22 at 12V a current of around 600 mA will be needed in power up mode Switch on your SK86R12 01 Promotion Board using switch SW9 large switch on the bottom right hand corner of the PCB and check that LEDs D6 D7 and D8 light up FSEUGCC UM SK86R12 01 Rev1 4 11 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJITSU SK 86R12 01 e After the board has powered up the embedded Linux operating system is started and a demonstration program will be run this can take a number of seconds Please monitor the messages in the terminal console window for any errors or warnings After the system has completed booting a dashboard demonstrator will be shown on the display Trying to mount an usb memory device for 10 seconds 7 020000 isp1760 isp17 60 0 port 1 high speed 7 080000 usb 1 1 new high speed USB device number 2 using isp1760 7 140000 isp1760 isp1760 0 port 1 high speed 7 220000 usb 1 1 New USB device found idVendor 0471 idProduct 3526 7 220000 usb
13. ce for data that is not touched a safe backup system while the other device is being reprogrammed and used In the event of problems this would ensure that it is always possible to boot from the backup device FSEUGCC UM SK86R12 01 Rev1 4 33 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 10 4 1 Overview of possible Use Configurations 16 bit access U34 active Set SW5 to switch position 2 3 default Set SW8 to switch position 2 3 default The first NOR device U34 only will be used in 16 bit mode U35 is then not used and could be used for system recovery if booting from U34 fails 16 bit access U35 active Set SW5 to switch position 2 3 default Set SW8 to switch position 1 2 The second NOR device U35 only will be used in 16 bit mode 32 bit access U34 U35 active Set SW5 to switch position 1 2 Set SW8 to switch position 2 3 Both devices will be activated using the XCSO signal FSEUGCC UM SK86R12 01 Rev1 4 34 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 11 360 Wrap Around View WAV System SD Card Reset HDMI DVI Mini USB USB bottom side button output top UART Host SPI Digital Input bottom side Analog input gt Cap 1 Back Cap2 Lleft gt Cap3 Right Cap0 Front Power supply 9 18V DC SW6 1 8 1111 0000 analog i
14. e contact Fujitsu support for details and consult Texas Instruments Application Report TVP5150AM1 Anti Aliasing Filters document SLEA087A 2010 Please check the datasheet of the respective device for details Please refer to page 29 of the board schematics for details 8 2 5 Video Capture for 360 Wrap Around View using all 4 capture units If you have purchased the SK86R12 01 Emerald P Promotion Board as a part of the 360 Wrap Around View package then you will be using all four video capture units simultaneously whether 4x ITU656 or 4x digital input This package includes an additional add on board Add on 360 Wrap Around View board which has an X33 connector with the inputs for all four capture units as well as SPIO UARTO GPIOs and 2 pins to control the connected cameras Please refer to Chapter 8 for details on the 360 WAV product FSEUGCC UM SK86R12 01 Rev1 4 26 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 8 3 Ethernet using internal MAC external PHY The SK86R12 01 Promotion Board has an RJ45 connector X17 which is used to connect the board to an Ethernet network this will typically be a small local network on your workplace used for development work By default the board operates in a 100MBit mode although the MB86R12 has a built in 1GB MAC However the board itself can not support the faster link because the copper track routing on the PCB als
15. een nnne nennen 25 8 2 3 Capturing Video via Pin Header X34 RGBS8898 sssssssssseeeeeeres 25 8 2 4 Capturing Video ITU656 ssssssssssssseseseeeeen eene nennen nennen nennen 26 8 2 5 Video Capture for 360 Wrap Around View using all 4 capture units 26 8 3 Ethernet using internal MAC external PHY s 27 MEM IS 27 8 5 JTAG 16 Bit Trace 5 27 8 6 Mini USB to RS232 HOST SPI lC 28 8 6 1 ale MES INIMICI 28 dos 5939 UART DOS usce tonta diti tei Gies etiara 28 8 6 3 MERE TER 29 8 7 GAN Interface eer 29 LESE OS D BIN e e 29 89 SD Card B otto etr nk eoru 29 Sx pnm 30 8 11 AIC IPG c 30 9 inc Rd 32 1 Raub ee aeris 32 10 n 39 FSEUGCC UM SK86R12 01 Rev1 4 5 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 10 1 DDR3 U27 2G m 33 10 2 QUAD SPI sime 33 10 3 NAND Flash MARKEN nM US EM
16. f 128MBit 16 Mbyte It is also possible to boot the system from this flash provided the following setup exists Switch 8 of SW7 must be set ON to use the SPI flash ENABLE QUAD SPI FLASH Required Pin Multiplexing Mode PinMuxGroup A MuxMode 41 is required to use the QUAD SPI flash Please refer to the specification of the memory device for programming details Please refer to page 17 of the board schematics for details 10 3 NAND Flash U39 The SK86R12 01 Promotion Board incorporates a 2GBit NAND Flash device with 1 Bit ECC from Micron MT29F2G16ABAEAWP IT which offers 16 bit data lines In the default setup the device is not used as a boot device the memory is selected via Chip Select signal XCS1 default over OQ resistor R344 However if you wish to boot from the NAND you must assemble R340 also a OQ resistor and use Chip Select signal XCSO the MB86R12 always boots from 8 Please refer to the datasheet of this device for details on programming Please refer to page 17 of the board schematics for details 10 4 NOR Flash U34 U35 The Emerald P Promotion Board incorporates two 1GBit NOR flash devices from Micron type JS28F00AM29EWL Use Chip Select XCSO to access the NOR flash chip Normally the memory will be accessed in either 16 bit or 32 bit mode the bus is designed to handle both modes but it is also possible to address the two devices separately in 16 bit mode making it possible to reserve one devi
17. hernet 6 TRACE ae JTAG itrace interface 7 1250 uc T I2S sound interface TIE T The software supplied with the board is configured to run with this setup and the corresponding pin multiplexing configuration Before activating an interface please configure the MB86R12 to use the corresponding pin multiplex group when booting This is achieved using the U Boot bootstrap utility described further on in this User Manual Please check also board schematics page 2 and the corresponding page of the interface SW7 can be found on page 2 of the schematic Rev1 7 FSEUGCC UM SK86R12 01 Rev1 4 20 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 on Default Settings SW6 unused unused Use capture interface 0 ITU656 Use capture interface 1 ITU656 Use capture interface 2 ITU656 Use capture interface 3 ITU656 Use HDMI capture RGB888 Use HDMI capture sound All these interfaces are deactivated by default Before activating an interface please configure the MB86R12 to use the corresponding pin multiplex group when booting This is achieved using the U Boot bootstrap utility described further on in this User Manual Please check also board schematics page 2 and the corresponding page of the interface SW6 can be found on page 2 of the schematic Rev1 7 FSEUGCC UM SK86R12 01 Rev1 4 21 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotio
18. itive the outer ring has to be connected to ground A suitable power supply can also be delivered by Fujitsu please contact your Fujitsu Sales Representative if required all the switch settings on the board e g pin multiplex settings interfaces to be used are correct for your application The default settings of the switches are described in this document To bring the system into operation quickly execute the following steps Install the drivers for the FTDI components on your board either by obtaining the latest version from the FTDI website or from the WAV Tools DVD e g E Driver CDM 2 08 24 WHQL Certified http www ftdichip com Drivers VCP htm http www ftdichip com Support Documents InstallGuides htm Connect a mini USB cable to J1 and the other end to your PC The SK86R12 01 Promotion Board will be automatically recognized and four new COM ports will be installed as follows o USB Serial Converter A can be used as the HOST SPI interface o USB Serial Converter B can be used as an 12C interface direct to devices o USB Serial Converter C can be used as the UARTO interface o USB Serial Converter D can be used as the UARTA interface Note that Windows may not use exactly these names however the third COM port installed is the one that is required for the next installation step Start a terminal program such as Tera Term http ttssh2 sourceforge jp with the following configuration o Baudr
19. k of Philips Semiconductor Corporation in the United States and other countries SPIG Serial Peripheral Interface is a registered trademark of Motorola Corporation in the United States and other countries RSDS and PPDS are registered trademarks of National Semiconductor Truevision is a registered trademark of Truevision Inc TGA is a trademark of Truevision Inc Other system names or product names which may appear in this document are the trademarks of the respective company or organization FSEUGCC UM SK86R12 01 Rev1 4 3 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 Warranty and Disclaimer To the maximum extent permitted by applicable law Fujitsu Semiconductor Europe GmbH restricts its warranties and its liability for all products delivered free of charge eg software include or header files application examples target boards evaluation boards engineering samples of IC s etc its performance and any consequential damages on the use of the Product in accordance with i the terms of the License Agreement and the Sale and Purchase Agreement under which agreements the Product has been delivered ii the technical descriptions and iii all accompanying written materials In addition to the maximum extent permitted by applicable law Fujitsu Semiconductor Europe GimbH disclaims all warranties and liabilities for the performance of the Product and any consequential damage
20. l NOR flash and the settings for NOR flash in the table below applies f SELFL 1 the system boots from NAND provided INTA4 A7 are changed to 1111 Then the 2Gb 16 bit NAND U39 can be accessed by the bootstrap function note that in SW10 MPXMODE 2 0 must also be set to 100 for this 1 2 Logical 1 2 3 Logical isi CO BERN MP 1 Ws 3 INT A5 TO sw12 A rz im EI 1 2 3 did O iki pec negl Ra 1 A Part Number Group Switch Switch Name Function Sets the operation mode of the serial SW11 NOR Flash 1 INT_A4 flash device 00 Single Mode default 01 Dual Mode SW12 NOR Flash 1 INT A5 10 Quad Mode 11 Reserved Sets the memory type in use SW13 NOR Flash 1 INT A6 0 Winbond W25Q16BV default 1 Spansion S25FL129P Reserved default 0 SW14 NOR Flash 1 INT A7 ash Required for NAND boot Note To change the settings of a switch you must first remove the thin protective yellow foil on the top of the switch body SW11 14 can be found on page 8 of the schematic Rev1 7 FSEUGCC UM_SK86R12 01 Rev1 4 18 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 s i SW5 2 NOR Flash 32 Bit NOR Flash 16 Bit 1 3 SW8 2 NOR Flash U35 used NOR Flash U34 used in 16 Bit Mode in 16 Bit Mode NOR Flash U34 U35 used in 32 Bit Mode 1 3 Part Number Group Switch Switch Name Fu
21. l data inputs relative to the clock input S1 uses U2 CTL1 default ON 0 S3 uses U3 3 CTLs CTL2 default ON 0 CTL3 default OFF 1 The default setting CTL 3 1 100 recommended setting Tcp Ons Data de skew enable default OFF E DREN logical 1 i e enable de skew Notes e HDMI output 0 Display 0 can only be used in conjunction with PinMuxGroup D MuxMode 0 e HDMI output 1 Display 1 can only be used in conjunction with PinMuxGroup F MuxMode 1 S3 can be found on page 10 of the schematic Rev1 7 For details on de skewing please refer to the datasheet of the TFP410PAP Texas Instruments device FSEUGCC UM_SK86R12 01 Rev1 4 23 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 8 1 2 Display Outputs via Pin Headers also for Glyn TFT family displays The SK 86R12 01 board also routes the RGB888 outputs of the three display units of MB86R12 Emerald P to 1 27mm pitch pin headers The X2 connector on the board was designed especially for the use of displays from Glyn s EDT display family These TFT displays can be ordered via www glyn de or also via Fujitsu Semiconductor Support and offer on board touchscreens and a fixed connector layout for a wide set of different resolutions and sizes The 7 pin on the board can be used to enable the panel by software and the SPIO DO pin can be used to dim the panel using PWM Pu
22. lse Width Modulation see schematics page 11 for both pins Before using a pin header please configure the MB86R12 to use the corresponding pin multiplex group when booting This is achieved using the U Boot bootstrap utility described further on in this User Manual DISD BT DISO H6 DISO BS DIS B4 DISD B3 DISO B2 DISO 67 DISO Gh Disp GS DISD G4 DISO G3 DISD G2 DISO R6 DISD DISD R3 DISD R2 3V3 display GPIO 87 PinMux H Mode 5 GPIOS7 R22 open DGND PWM OUTU R23 LEDCTRI 3V3 display O LEDCTRL AMP 4 1734742 0 DGND Required Pin Multiplexing Modes DisplayO requires PinMuxGroup D PinMuxModeO Display1 requires PinMuxGroup F PinMuxMode1 Display2 requires PinMuxGroup l PinMuxMode3 FSEUGCC UM SK86R12 01 Rev1 4 24 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 8 1 3 Display Output via APIX TX 3GBit The MB86R12 Emerald P chip provides three APIX TX interfaces which can be independently configured via software The interfaces are downwards compatible to APIX1 1GBit All the APIX interfaces are ESD protected and provided with Rosenberger connectors The Display 0 output APIX TXO can also utilize the Power over APIX PoA functionality which means that it is optionally possible to provide 12V the Vinput of the board over the APIX line This is not used by default Please note that additional components need
23. n Board SK 86R12 01 8 Interfaces 8 1 Display Outputs 8 1 1 Display Outputs HDMI 2 available The SK 86R12 01 incorporates two HDMI outputs e Display 0 this is the top connector of the stack e Display 1 These Emerald P outputs are connected to TFP410PAP Texas Instruments DVI transmitters U2 U3 and use the RGB888 output format The DVI transmitters are configured to operate without any additional software programming Their basic configuration is Single clock High Voltage Swing 24 Bit Single Edge Mode Rising Edge Mode De skewing 0 ns If you need to change this configuration this can be done using switches S1 for Display 0 and S3 for Display 3 Default Settings ON logical O OFF logical 1 on XP pb I ac 2 T E LE LU X rid 1 2 3 7 2 Lu b 6 b Split into parts in the schematic S1a S1d S1 can be found on page 9 of the schematic Rev1 7 FSEUGCC UM SK86R12 01 Rev1 4 22 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 Default Settings ON logical O OFF logical 1 te ES tee 537 m i 1 2 3 4 j 9 9 2 0 5 amp Split into parts in the schematic S3a S3d Part Number Group Switch Switch Name Function 1 CTL1 When DKEN OFF CTL 3 1 configure 2 CTL2 the DK de skew inputs of the TFP410PAP device 02 03 in order to adjust the setup and hold times of the pixe
24. nction 32 Bit Mode Sets the type of serial flash device SW5 NOR Flash 1 16 Bit Mode 1 2 32 Bit Flash 2 3 16 Bit Flash default Interacts with SW5 Sets the use mode for components U34 U35 see schematic 1 2 Use U35 in 16 Bit mode 2 3 Use U34 in 16 bit mode U34 U35 in 32 Bit mode default SW8 NOR Flash 1 Device Use Mode Summarizing the default configuration of the system is e Boot from NOR flash Use component U34 in 16 Bit mode Please check the board schematics on pages 2 and 8 Note To change the settings of a switch you must first remove the thin protective yellow foil on the top of the switch body SW5 can be found on page 2 of the schematic Rev1 7 SW68 can be found on page 14 of the schematic Rev1 7 FSEUGCC UM SK86R12 01 Rev1 4 19 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 7 4 Interfaces Configuration Default Settings SW7 Use UARTO Use UART4 J Use HOST SPI Interface Use SD Card Use external PHY Ethernet Use Trace Use Sound 1250 Use QUAD SPI Flash a B CB N B CB Part Number Group Switch Switch Name Function SW7 Interfaces 1 UARTO Enables use of UARTO default ON 2 UART4 Enables use of UART4 default OFF 3 HOST SPI Host SPI interface 4 SD CARD SD Card interface 5 EXT PHY ETH arene le Et
25. nput 0000 0000 digital input Power SW7 1 8 1111 0000 for a detailed description refer to the schematic switch Figure 11 1 Fully assembled SK 86R12 01 Board for WAV The SK86R12 01 Promotion Board is also supplied as a part of the 360 Wrap Around View product In this configuration the modified board is supplied together with four video capture cameras and its default switch configuration is different to match the application s requirements WAV Current Scope of Delivery analog cameras 1x Emerald P Promotion Board SK 86R12 01 with additional cinch connectors to connect the board to the output ports of the camera adapter box 1x Camera Adapter Box 4x Cameras ND BC1001I All cables required to set up the system Calibration Markers DVD and USB stick with documentation software and tools Optional Extra not included in delivery please order seperately 8 LCD Monitor 800x600 Important Note Ethernet Interface not available in WAV Configuration Please note that due to the pin multiplexing configuration that is required to use the hardware in 360 Wrap Around View mode the Ethernet Interface is not available Consider using a USB Network adapter as an alternative FSEUGCC UM SK86R12 01 Rev1 4 35 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 U Boot Modifications Required for WAV use Please check these settings if you install a Linux BSP upda
26. nt of up to 4A each A seperate 5V supply max 4A is available for external use e g for external cameras the 360 WAV add on board for digital cameras etc The external power input is fused and protected against reverse polarity 9 1 External Startup It is possible to start up the SK86R12 01 Promotion Board using an external control e g coming from an Atlas Starterkit Pin 25 of connector X9 provides this functionality whereby a HIGH signal level triggers a power up sequence on the SK86R12 01 Promotion Board 6 n ae N lahald wj us w Nir 2 4 im 10 12 g 14 16 a HSER 22 28 30 36 38 4 40 7 Please check page 27 of the board schematic FSEUGCC UM SK86R12 01 Rev1 4 32 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 10 Memory 10 1 DDR3 U27 U28 The SK86R12 01 Promotion Board incorporates two Micron MT41J128M16HA 15E DDR3 memory devices each with 2GBit 256 MByte These devices can attain data rates up to 1 333 MT s Million Transfers per second and are organized as 16Mbit x 16 x 8 banks The correct configuration of the memory devices is handled by the U Boot utility Please refer to page 16 of the board schematics for details 10 2 QUAD SPI Flash U40 The SK86R12 01 Promotion Board incorporates a QUAD SPI flash device from Spansion S25FL129POXNF100 which offers a capacity o
27. ntact your Fujitsu sales representative if you require such an adapter Required Pin Multiplexing Mode The JTAG interface is enabled by default and a specific pin multiplexing setup is not required for use PinMuxGroup B MuxMode 3 is required to use the 16 Bit Trace interface Switch 6 of SW7 must be set to ON for use of the Trace interface Enable Trace Please refer to page 22 of the board schematics for details FSEUGCC UM SK86R12 01 Rev1 4 27 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 8 6 Mini USB to RS232 HOST SPI 20 Interface The SK86R12 01 Promotion Board has a bus powered FTDI chip that provides the following interfaces via virtual COM ports two RS232 ports e one 20 interface one HOST SPI port When connected via USB Windows automatically recognizes the FTDI hardware as follows USB Serial Converter A can be used as the HOST SPI interface USB Serial Converter B can be used as an interface direct to devices see below USB Serial Converter C can be used as the UARTO interface USB Serial Converter D can be used as the UARTA interface f you are using Windows XP you will need to install the FTDI drivers manually first see Quick Start chapter 8 6 1 HOST SPI Interface The HOST SPI interface can be used to access the MB86R12 Emerald P device Fujitsu GDC Studio is a complete development tool suite that includes a driver fo
28. o has to take the multiplexed use of the Ethernet pins into account and this makes full speed usage impossible To use the Ethernet functionality please set switch 5 of SW7 to ON Enable ext PHY Required Pin Multiplexing Mode PinMuxGroup 1 MuxMode 1 or 2 are required to use the internal MAC and PHY units for Ethernet communication Please refer to page 18 of the board schematics for details Important Note Ethernet Interface not available in WAV Configuration Please note that due to the pin multiplexing configuration that is required to use the hardware in 360 Wrap Around View mode the Ethernet Interface is not available Consider using a USB Network adapter as an alternative 8 4 USB Host Interface The SK86R12 01 Promotion Board has a USB connector X23 that can be used to connect external hardware USB mouse USB keyboard USB hub USB stick etc The USB interface can always be used and is independent of any pin multiplexing settings Please refer to page 20 of the board schematics for details 8 5 JTAG 16 Bit Trace Interface The SK86R12 01 Promotion Board incorporates a JTAG 16 Bit Trace debugging interface to enable fast and easy access to the register set of MB86R12 Emerald P To use this interface connect the 38 pin MICTOR connector of your debugger to connector J2 on the PCB Note that Fujitsu s GDC Support Team can also deliver an adapter for standard 20 pin 2 54mm pitch connectors e g for Realview Co
29. ortant note below concerning the use of PSMODE Connected to the VINITHI line of the ARM core which determines the starting address of the exception vectors 8 VINITH 0 exception vectors are located at 0x0000_0000 default 1 exception vectors are located at OxFFFF_0000 Important Note For Board Owners with an MB86R12 up to ES2 Engineering Samples Step 2 To use the JTAG interface with the Fujitsu Developer Suite tool you must set the PSMODE switch to OFF 2 binary value 1 enabling reliable use of the JTAG interface If you are using a different tool e g GHS Integrity or RealView then the PSMODE switch can be set to ON To check which ES you have please look at the date code on the package or check the chip s ID register ES1 ES2 Data code CCID Date Code CCID Emerald P 1132 865212F1 1150 865212F2 Please check also board schematics page 8 Summarizing the default DIP switch configuration shown above for SW10 and SW15 the board is configured to run at 533 MHz and software can be uploaded via Ethernet SW10 can be found on page 8 of the schematic Rev1 7 FSEUGCC UM SK86R12 01 Rev1 4 17 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 7 3 Bootstrap Options and Flash Configuration The effect of the settings made with the following DIP switches depend on the setting of SELFL see SW15 e If SELFL 0 the system boots from Seria
30. pplicable law Fujitsu Semiconductor Europe GmbH disclaims all other warranties whether expressed or implied in particular but not limited to warranties of merchantability and fitness for a particular purpose for which the Product is not designated 4 To the maximum extent permitted by applicable law Fujitsu Semiconductor Europe GmbH s and its suppliers liability is restricted to intention and gross negligence NO LIABILITY FOR CONSEQUENTIAL DAMAGES To the maximum extent permitted by applicable law in no event shall Fujitsu Semiconductor Europe GmbH and its suppliers be liable for any damages whatsoever including but without limitation consequential and or indirect damages for personal injury assets of substantial value loss of profits interruption of business operation loss of information or any other monetary or pecuniary loss arising from the use of the Product Should one of the above stipulations be or become invalid and or unenforceable the remaining stipulations shall stay in full effect FSEUGCC UM SK86R12 01 Rev1 4 4 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 Table of Contents 1 ioo T 7 DE 7 1 2 Mechanical Dimensions eeeeeeeeeeeeeeeee eene nenne nennen nnne nennen nnn n nnn n nnn nn nnn 8 2 Information and Support on the Internet eeeeeeeeeeses 9 3 S
31. r this purpose Check this link for details on Fujitsu Developer Suite http www fujitsu com emea services microelectronics gdc swtools fj developer suite html Required Pin Multiplexing Mode PinMuxGroup B MuxMode 1 is required to use the HOST SPI interface Switch 3 of SW7 must be set to ON to use the HOST SPI interface Enable SPI Host 8 6 2 RS232 UART Ports The RS232 ports are connected to Emerald P s UARTO and UART4 and will be detected if a mini USB cable is used to connect J1 mini USB to a PC To enable the use of the UART ports e g for a terminal connection the following settings must be made on the board Switch 1 of SW7 must be set to ON default for UARTO Enable UARTO default setting Switch 2 of SW7 must be set to ON default for UART4 Enable UART4 To use a RS232 communication port please make sure your terminal software e g Tera Term http ttssh2 sourceforge jp is configured with the following settings e Baud rate 115 200 bps e Data 8 bits e Stop bit 1 bit e Parity none e Flow Control none FSEUGCC UM_SK86R12 01 Rev1 4 28 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 8 6 3 Interface It is possible to use this 0 interface available on connector X10 to directly program 1 C devices on the board although this is normally handled by the MB86R12 Emerald P device If you wish to use this interface for test or debugging purpo
32. s in cases of unauthorised decompiling and or reverse engineering and or disassembling Note all these products are intended and must only be used in an evaluation laboratory environment 1 Fujitsu Semiconductor Europe GmbH warrants that the Product will perform substantially in accordance with the accompanying written materials for a period of 90 days form the date of receipt by the customer Concerning the hardware components of the Product Fujitsu Semiconductor Europe GmbH warrants that the Product will be free from defects in material and workmanship under use and service as specified in the accompanying written materials for a duration of 1 year from the date of receipt by the customer 2 Should a Product turn out to be defect Fujitsu Semiconductor Europe GmbH s entire liability and the customer s exclusive remedy shall be at Fujitsu Semiconductor Europe GmbH s sole discretion either return of the purchase price and the license fee or replacement of the Product or parts thereof if the Product is returned to Fujitsu Semiconductor Europe GmbH in original packing and without further defects resulting from the customer s use or the transport However this warranty is excluded if the defect has resulted from an accident not attributable to Fujitsu Semiconductor Europe GmbH or abuse or misapplication attributable to the customer or any other third party not relating to Fujitsu Semiconductor Europe GmbH 3 To the maximum extent permitted by a
33. ses you must first obtain Third Party software from Future Technology Devices International Ltd FTDI Please visit the FTDI webpage for more information http www ftdichip com and refer to Application Note AN 177 User Guide For libMPSSE I2C Furthermore you will need to modify the PCB add 00 resistors at R268 and R269 and disable the unit of MB86R12 Emerald P Please refer to page 23 of the board schematics for details 8 7 CAN Interface The SK86R12 01 Promotion Board incorporates a CAN bus connector X16 If you own or have access to the Jade L Starterkit SK 86R03 then you can use the adapter supplied with this to connect a 9 pin sub D connector 10 pin pin header to 9 pin sub D adapter Please refer to page 24 of the board schematics for details 8 8 MediaLB Interface The SK86R12 01 Promotion Board incorporates an SMSC MOST module bus connector X12 This connector can be used directly with SMSC PHY Modules available for different speeds MOST 25 50 For more information please check the SMSC website http www smsc ais com AlS content view 852 818 The MediaLB interface is also available on a seperate connector X14 Required Pin Multiplexing Mode PinMuxGroup G MuxMode 0 is required to use the MediaLB interface Please refer to page 24 of the board schematics for details 8 9 SD Card Interface The SK86R12 01 Promotion Board provides a SD Card interface with a card reader X16 Switch 4 of SW
34. te from the Fujitsu website pinmux 80000000 pinmux2 00000168 tcon_pinctrl 93 cpumem mem 256M gpumem gpumem 256M SK86R12 01 Promotion Board Layout Modifications Please note that the SK 86R12 01 board is supplied in a slightly modified form when delivered as a part of the 360 Wrap Around View product package The differences are e ADC filter configuration e Additional cinch connectors are mounted X25 capture 0 X31 capture 1 X29 capture 2 X28 capture 3 O O O SK86R12 01 Promotion Board Switch Configuration WAV 4 Analog Cameras on Default Settings SW6 unused unused Use capture interface 0 ITU656 Use capture interface 1 ITU656 Use capture interface 2 ITU656 Use capture interface 3 ITU656 Use HDMI capture RGB888 Use HDIVII capture sound j RT 8 Please note that this setup requires an additional add on board SK 86R12 WAVO 1 FSEUGCC UM SK86R12 01 Rev1 4 96 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 WAV 4 Digital Cameras on SW6 Use capture interface 0 ITU656 Use capture interface 1 ITU656 Use capture interface 2 ITU656 WAV SW7 Use UARTO Use UART4 Use HOST SPI Interface Use SD Card Use external PHY Ethernet Use Trace Use Sound 1250 Use QUAD SPI Flash Default Settings unused unused Use HDMI capture RGBE888 Use HDMI capture sound Use capture interface 3 ITU656 Default Se
35. to be assembled for PoA operation refer to the schematics For details refer to board schematics page 12 and page 13 8 2 Video Capture Interfaces 8 2 1 Capture via APIX RX RGB888 3GBit Link This mode enables the capture of data via the APIX Link 3GBit via an internal APIX RX path Please refer to page 13 of the board schematics 8 2 2 Capturing via HDMI RGB888 To enable the capture of video data in high quality via the HDMI interface enable switch 5 Enable HDMI Capture of SW6 The data is converted into the RGB888 format and transferred to the CaptureO interface of MB86R12 Emerald P Required Pin Multiplexing Mode PinMuxGroup 41 MuxMode 0 is required To additionally enable the capture of sound data transmitted via the HDMI interface enable switch 6 Enable HDMI Capture Sound of SW6 The data is then transferred to the 250 interface of MB86R12 Emerald P Please refer here to page 31 of the board schematics and the AD9398 datasheet for details see appendix AD9398 120 Write address 0x98 AD9398 I C Read address 0x99 8 2 3 Capturing Video via Pin Header X34 RGB888 MB86R12 Emerald P s CaptureO interface can be accessed via pin header X34 in order to feed a 24 bit RGB888 data stream into the device Required Pin Multiplexing Mode PinMuxGroup 7t MuxMode 0 is required Please also refer to page 31 of the board schematics FSEUGCC UM SK86R12 01 Rev1 4 25 Q Fujitsu Semiconductor Europe GmbH FUJI
36. tration program press any key on your keyboard quickly after a board reset SW4 or power on SW9 Using specific commands the configuration of the MB86R12 can be queried printenv command on the command prompt of the terminal program and configured using the setenv command To set up a new pin multiplex configuration for example check the values returned for the pinmux and pinmux2 environment variables using the command printenv on the command line prompt then change the configuration using for example setenv pinmux 84000000 setenv pinmux2 00000000 saveenv The U Boot utility is described in detail in the documentation provided with the SK86R12 01 board Please check the Software Development Platform document at the time this User Manual was written this document was named um MB86HR1 1 SoftwareDevelopmentPlatform pdf and was located in the root folder of the downloadable Linux BSP UpdateHost v3 2 0 zip FSEUGCC UM SK86R12 01 Rev1 4 13 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 6 Board Layout In the standard delivery form the board s layout is as shown in the diagram below Power IN EB gt 08 n sws m Figure 6 1 Standard Board Layout Assembly FSEUGCC UM_SK86R12 01 Rev1 4 14 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 7 Board Configuration DIP Switches The Emerald
37. ttings PeP nnn FSEUGCC UM SK86R12 01 Rev1 4 37 Fujitsu Semiconductor Europe GmbH co Emerald P Promotion Board FUJ ITSU SK 86R12 01 WAV zg n FE Le Es 1 N mer e inp e rl i 7 p o SRR JU m 0 mm 38 i gt i Fo p E S57 EEn E sl i To E gt e SW5 NU 2 i u NOR Flash 32 Bit a NOR Flash 16 Bit 1 3 SW8 2 NOR Flash U35 used NOR Flash U34 used in 16 Bit Mode in 16 Bit Mode NOR Flash U34 U35 used in 32 Bit Mode 1 3 WAV 1 2 Logical 1 2 3 Logical 2 LEES J m INT A4 TOL noem Tek 1 3 is 2 L TI s TO swi2 ken banneri e o 1 3 MED zy s INT_A7 SW14 NT e N w m zu Sun f a 153 abe g es 11 ann 5 FSEUGCC UM SK86R12 01 Rev1 4 38 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 WAV Default Settings on ON logical 0 OFF logical 1 ra 5 eo 9 8 8 39 A O O O O E E E w gt 3 3 3 D gt gt gt x x x m E a a a Uv 9 Ss 5 Tox TT i it a E f t amp Tales HE JA 111 E ls D rk Default Settings on ON logical 0 OFF logical 1 SW15 TE o a e Uu d m 2 5 D
38. ww fujitsu com emea services microelectronics gdc swtools fi developer suite html Datasheet FTDI FT4232HL Chip http www ftdichip com Support Documents DataSheets ICs DS_FT4232H pdf SMSC PHY Modules http www smsc ais com AlS content view 852 818 Datasheet Video Processor TVP5150AM http www ti com product tvp5150 FSEUGCC UM_SK86R12 01 Rev1 4 4 Fujitsu Semiconductor Europe GmbH FUJITSU Emerald P Promotion Board SK 86R12 01 12 2 Figures Figure 10 Figure 4 1 Console Output Pa an i evo La E Vda Rs Raga ees ad 12 Figure 4 2 Running Demosth tv ete Feria Ge teen ARR R Vee nV asst 12 Figure 6 1 Standard Board Layout Assembly sisse sisse entente nnns nnns 14 Figure 11 1 Fully assembled SK 86R12 01 Board for WAV eene 35 FSEUGCC UM SK86R12 01 Rev1 4 42 Fujitsu Semiconductor Europe GmbH
39. ystem OvervieW 10 ree CI e 11 b About U BOOL rre kei qa kk duas RE d E d RE d PE EK E REP Va Ed 13 AE Board LAY OU 14 7 Board Configuration DIP 6 15 7 1 DIP Switch SW10 JTAG Pin Multiplex Mode 15 7 2 DIP Switch SW15 Boot Flash Selection PLL Exception Vectors 16 7 3 Bootstrap Options and Flash Configuration 18 TA Interfaces Conflguratlon ecce hne nnn rka nana an anna nda innu EX an KR A Sd ECCE CEA RAE 20 8 22 Rel eee 22 8 1 1 Display Outputs HDMI 2 available sese 22 8 1 2 Display Outputs via Pin Headers also for Glyn TFT family displays 24 8 1 3 Display Output via APIX TX 3GBit esssssssssssseseeneneneeeneen enne 25 8 2 25 8 2 1 Capture via APIX RX RGB888 3GBit Link sssssssseeeeneenes 25 8 2 2 Capturing via HDMI RGB8898 ssssssssssssesss s
Download Pdf Manuals
Related Search