Untitled - Electrocomponents
Contents
1. C3 The parameters available on the right side are Output voltage Output frequency and Load as a percentage The displayed values can be set using the ON and SELECT keys The SELECT key is used to choose the field to be set while the ON key is used to confirm the selection The first time the SELECT key is pressed for 3 seconds then the keys should be pressed for about 1 second the left part will start to flash The second time this key is pressed the right part will start to flash and if pressed for a third time nothing will flash When a field is flashing press ON to confirm Press SELECT to choose the required value Press to confirm the selected value When the UPS is on in both mains and battery mode it will show the following default values respectively cI 230 2307 Eu 57 Shown below is an example of the procedure to set the display to show the Input voltage on the left side of the display Part A and Capacity as a percentage of the battery on the right side Part B Configuration example 2307 230 a BATTERY m Ep Press SELECT to change the field Press SELECT for 3 seconds Press ON to confirm the field Press SELECT to 72307 SADE see Press SELECT to Q3 ue change the value e 30 YS to be monitored m EE B gt Press ON confirm the value to be mo2. M Wa VAL 49 CONNECTION Connect the UPS to the mains power supply using the input supply cable Connect the loads to the UPS sockets with the IEC IEC cables or with a similar cable with a maximum length of 10 metres Note do not connect loads that draw more than 10A to the 10A IEC sockets These loads can only be connected to the 16A IEC socket where fitted CONNECTION TO THE NET TEL PROTECTION DEVICE A telephone modem network line can be connected to the modular RJ 45 RJ 11 connectors located on the rear of the UPS to protect against surge voltages A telephone extension cable is required for this type of connection N B This connection is optional The Net Tel protection is active even when the UPS is switched off or disconnected from mains power Warning The device that protects against overvoltages on the telephone line may not work if it is not installed correctly Ensure that the telephone line from the wall is inserted in the connector marked IN and that the cable of the device to be protected telephone modem network card etc is inserted in the connector marked OUT N B This protection device limits the effects of an overvoltage but does not guarantee absolute protection POWERSHARE All the models of the Dialog Vision range are provided with an auxiliary output socket that can be configured via UPSTools The Powershare socket can be configured in five different ways refer to the UPSTools
3. DVD only NS UF s 4 2 10 A connection cables IEC 16A loose plug DVD 2200 3000 VA models only Q User manual CD ROM software Warranty G 3 44 OPENING THE BATTERY BOX PACKAGING AND CHECKING THE CONTENTS After opening the packaging check the contents The packaging should contain the following Battery Box Q Guides for rack installation handles kit 45 CHECKING THE EQUIPMENT Check the UPS carefully If the UPS has been damaged during transit keep the box and the packaging Let the carrier and the supplier know immediately PLACING THE UPS This UPS must have an adequate airflow It must be placed in a clean indoor environment with no humidity away from flammable liquids and direct sunlight A space of at least 4 100 mm must be left around the UPS The ambient temperature must be between 0 C 40 C 32 F and 104 and the humidity level during operation must be between 2096 and 80 without condensation Warning long period of use in an environment with a temperature over 25 will shorten battery life The UPS should be placed at least 20 cm away from a monitor in order to avoid interference INSTALLING THE UPS The Dialog Vision family comprises DVT models designed for vertical installation and the DVR models which must be installed in 19 rack cabinets The DVD models can be positioned vertically using
4. be of the pin to pin type with a maximum length of 3 metres The interface with factory settings has the following characteristics RS232 CONNECTOR 12Vdc 80mA 7 PNP signal Contact closed battery low pre alarm Contact closed battery mode a SD With the UPS in battery mode if 5 15Vdc is applied for at least 20 seconds between PIN 3 and PIN 5 the UPS will shut down completely b B W contact closed in battery mode values max 25mA 35Vdc Vce sat max 1 5V 25mA c B L contact closed when battery is flat values 25 35Vdc Vce sat 1 5V 25mA d UPS Failure Alarm contact closed in the event of failure or signalling of alarms by the UPS maximum values 25 35Vdc Vce sat max 1 5V 25 e Input programmable via RS232 5 15 Vdc USB PORT The USB port is used to establish communication between the UPS and a PC When the communication cable is installed the management software Powershield can exchange information with the UPS The software can provide detailed information on the UPS operating status In the event of a mains power supply failure the software can save the data and shut down the computer Note The USB port and the RS232 serial interface located on the rear of the UPS cannot be used at the same time as the use of one excludes the other COMMUNICATION SOCKET All UPS are provided with an expansion slot for optional communication cards
5. indicators for details 54 LCD INDICATORS This chapter provides a detailed description of all the display indicators ICON STATE DESCRIPTION oteady on Indicates a fault see table 3 Flashing The UPS is in stand by mode Steady on The UPS is operating in mains mode The UPS is operating in battery mode In this state it will beep Steady on at regular 4 second intervals When operating in battery mode the UPS signals that it is Flashing about to switch off due to end of discharge In this state it beeps at regular 1 second intervals Steady on Indicates that the battery is faulty Steady on The AVR function 1 active Steady on The Powershare socket is active Represents the estimated percentage of battery charge BATTERY see table 1 Indicates the of load applied to the UPS in relation to the Active nominal value LOAD see table 2 Flashing The UPS is in an overload condition 55 1 60 80 80 100 50 75 75 102 flashing In the event of an overload the UPS will continue to power the load for a set period of time The UPS will emit an alarm to signal that it can no longer support the overload a beep at regular one second intervals Once the load has been reduced to within the 10096 threshold the UPS will return to normal operating mode Warning lf the overload is too high the protection device will be activated and the UPS will shut down To restore normal operation fo
6. inverter drawing energy from the internal battery set The UPS can operate from a mains power supply even if there is no battery available In this instance all other functions AVR start up or shutdown and overload protection are available CHARACTERISTICS Sinusoidal output voltage Front panel LCD Microprocessor control for high reliability High frequency technology Automatic correction of input voltage fluctuations by the built in Automatic Voltage Regulator AVR The AVR compensates for input voltage variations within a defined input voltage window and maintains a stable output without resorting to batteries Using the batteries less frequently ensures that they are at full capacity when they are actually needed and helps them to last longer Selectable output range Cold start Integrated volt free contacts RS 232 USB port Back up time can be increased by adding a battery box DVD 2200VA 3000VA models only Overload short circuit and overheating protection Configurable as Rack or Tower DVD models only Models DVR and DVD suitable for installation in 19 rack cabinets The various versions of the product are shown below 40 Dialog Vision Tower Dialog Vision Rack Dialog Vision Dual DVT DVT DVT DVT DVT DVR DVR DVR DVD DVD DVD 50 80 110 150 200 50 50 50 150 220 300 Nominal output 200 208220 230 240 Dimensions 438X44X460 438X88X582 LxHxD 110X240X395 160X240X435 19 x1Ux460 19 x2Ux582 FRONT VIEW DVT 5
7. our Uninterruptible Power Supply UPS Our company is highly specialised in the development and production of uninterruptible power supplies UPS The UPS in this range are high quality products designed and built with care to ensure optimum performance This equipment can be installed by anyone subject to a CAREFUL AND THOROUGH READING OF THIS MANUAL This manual contains detailed instructions on how to use and install the UPS For information on using and getting the best performance from your UPS this manual should be kept safely near the UPS and CONSULTED BEFORE TAKING ANY ACTION Reproduction of any part of this manual partial or in full is strictly prohibited without the manufacturer s prior consent The manufacturer reserves the right to modify the product described herein in order to improve it at any time and without notice Microsoft Windows and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries 39 This manual describes the Dialog Vision UPS family DVT DVR DVD and their related battery box The Dialog Vision is a line interactive UPS The UPS protects equipment connected to it from a mains power supply failures b surges C sags and brownouts The UPS automatically corrects its output for small fluctuations in the mains power supply In the event of larger fluctuations or a complete mains power supply failure its output is powered from the
8. 0 80 110 DVT 150 200 l u s 0 IBUWUQG VISION riell DVR 50 80 110 Malo D ups fielo UPS VISION Dialog Vision Battery Box 09100 DORILOGS VIS TON BATTERY BOX 4 REAR VIEW DVT 50 80 110 DVT 150 200 Oooo 0000 0000 0000 OOOO OOOO 99090 0000 0000 0000 0000 uuu DOOD OOOO OOOO Qoo DULL 2 OOOO 02000 a oo00 0000 OOOO OOOO 0000 0000 7 lt SN 3 em fe AY 6 W TA QW AON D WW DVR 50 80 110 0 2 5 W D D B I DVD 150 D 00 3 42 Lit il ka i O GO O O O OOOO e o e o o oo 000808 9 Lu jafu 0 o o e oo oo e a o Qo ds pu eel me unm lt umb T O DVD 220 300 8 3 RS232 serial interface Cooling fan Net Tel protection Input thermal protection IEC network input plug IEC output plug max 10 Expansion slots for interface cards Battery expansion connector IEC output plug max 16 Output thermal protection USB port EPO Fuse Powershare socket 43 OPENING THE UPS PACKAGING AND CHECKING THE CONTENTS After opening the packaging check the contents The packaging should contain the following UPS Q Plastic supports DVD model only IEC 10A power cable IEC 16A for DVD models Q Guides for rack installation handles kit 220 300 only models DVR and
9. 0442629098 www riello ups com riello riello ups com 165 OMNULC1RUB
10. 2 Disconnect the EPO input terminal from the UPS 3 Remove the jumper fixed to the terminal 4 Apply a volt free contact signal isolated and normally closed Vmax 60 Vdc 30 Vac RMS Imax 20 between Pin 1 and 2 of the terminal using an unshielded wire of diameter 18 22 AWG 0 75 0 3mm 5 Reconnect the terminal to the EPO input 6 Ensure that the switch connected to the EPO contact cannot be activated by a device powered by the UPS 7 Connect the UPS to the mains power supply and switch it on using the ON key 8 Activate the EPO contact by means of the external switch to ensure the UPS shuts down 9 Deactivate the EPO contact by means of the external switch and restart the UPS INSTALLING AN ADDITIONAL BATTERY BOX The DVD 220 and DVD 300 models are provided with a connector that allows an external battery box to be connected to the UPS to increase the back up time available Note When connecting additional batteries a small spark may occur within the connector when the cable is connected Follow the procedure below to install the additional battery box 1 Connect the cable to the battery connector at the back of the battery box 51 2 Then connect the other end of the cable to the battery connector at the back of the UPS toos D D D D Togi Doro pen G Hu 3 add further battery boxes up to a total maximum capacity of 120Ah repeat the previous steps Note W
11. 3 Disconnect the cable 4 Remove the batteries on a flat surface 5 Insert the new batteries in the UPS 6 Reconnect the battery cable and secure the support 7 Replace the front panel of the UPS 65 Dialog Vision Tower MODEL g DVT 50 DVT 80 DVT 110 DVT NOMINAL Ho 150 200 Nominal voltage Nominal voltage 230 VAC Voltage range 160VAC 3 294VAC 3 50 60Hz Automatic selection Voltage stability in battery 230V 5 1094 mode utc 50 60Hz Automatic selection As selected for the input OUTPUT mode gt 110 alarm and failure after 3 minutes gt 150 failure after 5 cycles From mains power OVERLOAD gt 110 96 alarm and failure after 30 seconds From battery power gt 120 failure after 5 cycles TRANSFER TIME Typical 4 msec 6 msec max BATTERY Recharge time time Less than 6 hours at 90 e 110X240X395 160X240X435 Battery LM Not available 0 40 C from 20 to 80 relative humidity without condensation ENVIRONMENT RS 232 INTERFACE u slot Not available Protection devret Excessive battery discharging overcurrent short circuit overvoltage undervoltage overheating Safely certification Safely certification GS TUV CE OTHER EMC compliance EN60240 2 66 MODEL Dialog Vision Rack Dialog Vision Dual DVR50 DVR80 DVR110 DVD150 DVD 220 DVD 8 POWER Nominal voltage 230 VAC 160V
12. AC 3 Voltage range 294VAC 3 Frequency 50 60Hz Automatic selection Voltage stability In battery 230V 5 1094 mode i SR 50 60Hz Automatic selection As selected for the input Frequency stability In mains 0 1Hz mode nis gt 110 alarm and failure after 3 minutes OUTPUT From mains power OVERLOAD gt 150 failure after 5 cycles 3110 alarm and failure after 30 seconds From battery power gt 120 failure after 5 cycles Ue eel Typical 4 msec typical 6 msec max TIME 12V 18V 24V 48V V V Nominal battery voltage 8 8 96 96 Dimensions 438X44 3X460 438X87 9X582 UPS LxHxD mm 19 x1Ux460 19 x2Ux582 mm L CE Battery box Number of batteries BATTERY Dimensions ENVIRONMENT Work environment 0 40 C from 20 to 80 relative humidity without condensation RS 232 Yes USB Yes INTERFACE Expansion slot Yes P Yes Excessive battery discharging overcurrent short circuit overvoltage undervoltage Protection devices overheating m Safety certification GS TUV CE OTHER EMC compliance EN60240 2 Safety EN62040 1 1 Notes 1 be changed with UPSTools 200 208 220 230 240VAC some parameters can be changed with UPSTools 6 I lt u a LE 1 iu a mis e Wir iello Ups UPS MANUFACTURING S R L 37048 S PietrodiLegnago VR Italy VialeEuropa 7 ZAI Tel 390442635811 Fax 39
13. NFIGURATION SOFTWARE UPSTools software allows the user to configure the UPS and provides a full view of the UPS parameters and status through the USB port Refer to the UPS Configuration section in the UPSTools manual for a list of the possible configurations available Installation operations e Connect the USB communication port on the UPS to a USB communication port on the PC using the cable provided e Follow the installation instructions given in the software manual in the UPSTools folder on the CD Rom provided Visit the manufacturer s website to check whether a more recent version of the software is available 61 UPS ACOUSTIC SIGNAL TABLES 1 beep every 4 The UPS is operating in Check the input voltage seconds battery mode 1 beep per The battery is discharging Save your work and switch off the equipment second Overload in output Check the charge level indicator and remove some loads Continuous Check the indicators table and contact the reseller if b The UPS has a fault eep necessary UPS ALARMS TABLE The power cable is not connected correctly Check the power cable connection The wall socket may be fu The UPS does faultv Please contact a trustworthv electrician 1 Disconnect all the loads and ensure that there is nothing short circuiting the output not start up when is pressed The UPS output mav have short circuited or be 2 Ensure that the loads are not isolated or short circuited overloaded internal
14. harged before use Connect the UPS to the mains power supply and leave the UPS to recharge for at least 8 hours before discharging it 92 FRONT PANEL The front panel consists of a display and ON OFF and SELECT keys LCD 30 C j OUTPUT i AD ET TS BATTERY BATTERY Front panel LCD ON button OFF button SELECT button Part A Part B Part D Part C 53 The display can show two values the same time which can be selected from those available in part A and part B of the display Detailed description for Part A on the left 000 Por BATTERY 6 9 INPUT VAC input voltage unit Volt INPUT Hz input frequency unit Hz BATTERY V total battery voltage unit Volt estimated back up time as a percentage of the battery charge BATTERY MIN estimated battery back up time unit Minutes Note The estimated back up time in minutes is also provided when the UPS is working in mains mode Detailed description for Part B on the right m ood B Boi l Je pan OUTPUT VAC output voltage unit Volt OUTPUT Hz output frequency unit Hz LOAD load applied in output as a percentage Part C and Part D show the status of the UPS see section LCD
15. hen a battery box is installed the UPS must be configured for the correct total capacity of the batteries using UPSTools software in order to calculate correctly the remaining back up time and the battery charge The configuration must be done with the UPS switched on or in stand by mode For this kind of battery box the value to be added is 9 Ah For the DVD 220 300 models whose total battery capacity has not been increased the recharge current is 2 A After setting the nominal battery capacity with the UPSTools software if the value set is greater than 14 Ah the recharge current automatically increases to 6 A START UP SHUTDOWN To start up and shut down the UPS press the ON and OFF switch for at least three seconds Starting up for the first time after about 30 seconds check that the UPS is working properly 1 Simulate a mains power supply failure by unplugging the input power cable The load must continue to receive power the battery mode indicator should light up and the UPS should beep every 4 seconds 3 Reconnect the power cable Normal mains power operation should be restored START UP FROM BATTERY The UPS can be switched on even when no mains power supply is available and the battery is fully charged Just press ON for at least three seconds to start the UPS RECHARGING The UPS is supplied with fully charged batteries During shipping however they can lose some of their charge and so the batteries must be rec
16. llowing failure due to an overload continuous beep and load not powered reduce the load so that it falls within the 10096 threshold Hold the OFF button down until the continuous beep stops and then release it Wait until the UPS has completely shut down and then switch on again using the ON key 56 FAULT SIGNALLING All Dialog Vision models are provided with a self check system that can indicate any faults or failures on the display The symbols are shown below together with a description and the possible solutions to rectify the problem Table 3 List of faults Symbols in Part 2 I LI _ Check the level on the display and reduce the load 1 Ensure that the ambient temperature is lower The UPS has overheated than 40 2 Switch the UPS off and wait until it cools down 1 Disconnect all loads and ensure that there is The UPS output has short nothing short circuiting the output circuited 2 Ensure that the loads are not short circuiting internally Contact the reseller to check or replace the fan Output voltage out of range EC inverter failure UPS internal error Contact the reseller SETTING THE VALUES ON THE FRONT PANEL LCD The LCD has two parts left Part A and right Part B The left side displays the following parameters Input voltage Input frequency Voltage battery Capacity as a percentage of battery and Estimated back up time in minutes M i C3 RN NN TT
17. ly An Internal fuse may have Please contact the reseller blown There may be no output The UPS is not voltage in the socket used a DIESE powering the lass 1 Check the connection cable loads nine sockel p g 2 Ensure that the load does not exceed the UPS s maximum capacity The battery has back up time fully recharge the battery 2 Replace the battery The UPS fault indicator is The UPS has a fault on Save your work and stop the equipment See the LCD INDICATOR PANEL for details The battery fault 1 Check the battery connection indicator is Ihe battery is faulty 2 Please contact the reseller to order a new battery to on replace the faulty battery The equipment The UPS may be o ihe Check the load status UPS switch off The UPS emits a continuous The UPS is in a fault state Check the UPS acoustic signals table beep The buttons do The button is broken Please contact the reseller not work 62 When the battery fault indicator illuminates and the UPS emits an intermittent beep one second on one second off the battery may need to be replaced Check the battery connection or contact the reseller to order a new battery Warning A battery is dangerous since it can generate an electric discharge or a short circuit The following precautions must be followed carefully before replacing the batteries 1 Though the batteries can be replaced with the UPS on it is recommended to switch the UPS off and un
18. manual as described below Q ALWAYS standard configuration the Powershare socket is always active the load is powered as if it were connected to one of the other output sockets LOW the Powershare socket is normally active but after 10 seconds from the start of the battery low signal the Powershare socket is deactivated BATTERY WORKING the Powershare socket is active if the UPS is powered from the mains power supply if the UPS is working in battery mode the Powershare socket is deactivated BATTERY WORKING DELAYED the Powerashare socket is always active but after 1 minute of operation in battery mode or after 10 seconds in a battery low condition the Powershare socket is deactivated BUZZER when the UPS is working in battery mode the Powershare socket is activated and deactivated in the same way as the buzzer 50 INSTALLING THE EMERGENCY POWER Orr The DVR and DVD range are provided with an EPO contact This allows the UPS to be shut down immediately without having to wait for the shutdown procedure to be completed Note When the UPS has been switched off using this input it is not be possible to switch the device back on again even if the EPO contact is closed until the UPS has been restarted manually If the EPO contact is open the UPS will not restart even if the ON key is pressed Follow the procedure below to install the EPO switch 1 Check that the UPS is switched off
19. manuale d uso user manual betriebshandbuch manuel d utilisateur manual de usuario DIALOG VISION _ 500 3000 va 5 E riello Ups 1 INTRODUCTION PRESENTATION CHARACTERISTICS FRONT VIEW REAR VIEW INSTALLATION OPENING THE UPS PACKAGING AND CHECKING THE CONTENTS OPENING THE BATTERY BOX PACKAGING AND CHECKING THE CONTENTS CHECKING THE EQUIPMENT PLACING THE UPS INSTALLING THE UPS VERTICAL INSTALLATION OF THE DVD MODELS VERTICAL INSTALLATION OF THE DVD MODELS WITH BATTERY BOX POSITIONING THE FRONT PANEL LCD FOR DVD MODELS INSTALLING DVR AND DVD MODELS IN A RACK CABINET CONNECTION CONNECTION TO THE NET TEL PROTECTION DEVICE POWERSHARE INSTALLING THE EMERGENCY POWER Orr EPO INSTALLING AN ADDITIONAL BATTERY BOX START UP SHUTDOWN START UP FROM BATTERY RECHARGING SYSTEM DESCRIPTION FRONT PANEL LCD LCD INDICATORS FAULT SIGNALLING SETTING THE VALUES ON THE FRONT PANEL LCD ACOUSTIC SIGNALS BATTERY TEST COMMUNICATION PORT 40 4 41 42 43 45 45 46 47 47 47 47 48 49 51 52 52 52 53 53 54 54 54 55 95 55 57 59 59 61 61 62 37 RS232 INTERFACE USB PORT COMMUNICATION SOCKET SOFTWARE MONITORING AND CONTROL SOFTWARE CONFIGURATION SOFTWARE ALARMS AND INDICATORS REPLACING THE BATTERY DiALOG VISION TOWER DiALOG VISION RACK DiALOG VISION DUAL SPECIFICATIONS 38 62 62 62 63 63 63 64 65 65 66 67 68 Thank you for choosing
20. nitored 58 ACOUSTIC SIGNALS a Fault e g due to overheating or fan failure b Battery overcharged Intermittent 1s on 1s off C Overload Intermittent d UPS in battery mode 1s on 4s off Intermittent e UPS in battery mode with battery flat 1s on 1s off Intermittent f Battery disconnected after the battery test 1s on 1s off Intermittent for 3 g The UPS is performing the battery test times 0 5s on 0 5s off h If none of the events in the previous points has occurred Not active T nni 0123456789 10t severe 0123456789 10t innnnn 0123456789 10t 0123456789101 TAMIL 0123456789 10 innnnn 0123456789 10t 0123456789 10 lone 0 12345678914 In battery mode the acoustic signal can silenced by holding the key down for 3 seconds This will only remain inhibited if none of the events in points b e and f has occurred BATTERY TEST In mains mode hold the key down for more than 5 seconds a will sound to run a battery test lasting 5 seconds default time During the battery test the Line and Battery function icons will both light up 30 QUU LOAD Fa The battery test process 29 RS232 INTERFACE With the RS232 serial interface the UPS can be connected to a PC COM interface by means of a pin to pin serial cable if a different cable is used this must
21. plug the power cable from the wall 2 Remove any rings watches and other metal objects 3 If the battery replacement kit is damaged in any way or shows signs of leakage contact the reseller immediately Recycle the used batteries Never throw batteries into a fire as they may explode Do not open or damage the batteries The electrolyte contents are harmful to the skin and eyes and may be toxic For correct recycling do not throw the UPS the battery box or the batteries into the rubbish Contact the nearest waste recycling centre for information on how to dispose of the UPS the battery box and the batteries Follow the points and the table below to replace the batteries DIALOG VISION TOWER 1 Remove the front panel of the UPS by pulling with both hands 2 Disconnect the UPS battery cable Remove the plate securing the battery to the UPS 3 Take hold of the plastic battery tab and pull the battery out of the UPS 4 Insert the new battery in the UPS 5 Reinsert the plate and reconnect the battery cable 6 Replace the front panel of the UPS 63 DIALOG VISION RACK 1 64 Remove the front panel of the UPS by pulling with both hands Insert the new batteries in the UPS Screw the battery support and reconnect the cable Replace the front panel of the UPS DIALOG VISION DUAL 1 Remove the front panel of the UPS by pulling with both hands l au
22. so that the unit is compatible with the main communication standards Some examples e Serial port duplexer e Ethernet network agent with TCP IP HTTP and SNMP protocol e HS232 RS485 port with JBUS MODBUS protocol For more information on the options available please visit the manufacturer s website 60 The CD Rom provided includes two programs that enable the user to carry out monitoring control and configuration operations on the UPS MONITORING AND CONTROL SOFTWARE The Powershield software provides UPS management control and application shutdown it ensures effective and intuitive UPS management by displaying all the necessary data values such as input voltage applied load battery capacity The software can also automatically perform programmed shutdown start up operations shutdown the operating system of the PC or file server it is running on and send alarm e mails SMS and network messages when specific user defined events occur Installation Operations e Connect the USB communication port on the UPS to a USB communication port on the PC using the cable provided e Insert the CD Rom and select the operating system required e Follow the installation instructions e For more detailed information on installing and using the software refer to the software manual in the Manuals folder on the CD Rom provided Visit the manufacturer s website to check whether a more recent version of the software is available CO
23. the supports or installed in 19 rack cabinets VERTICAL INSTALLATION OF THE DVD MODELS The DVD models are provided with supports to stabilise the UPS when it is positioned vertically 1 Assemble the supports as shown in the figure 2 Putthe UPS in a vertical position and place the supports close to it Carefully insert the UPS in the two supports 46 VERTICAL INSTALLATION OF THE DVD MODELS WITH BATTERY BOX 1 Assemble the supports and the extension as shown in the figure 47 POSITIONING THE FRONT PANEL LCD FOR DVD MODELS The DVD LCD can be rotated to suit the kind of installation rack or tower The information below explains how to rotate the display A From Rack to Tower 1 Place the UPS flat and press the key shown Z 2 Rotate the LCD display 90 3 Reinsert the display in its housing 48 B From Tower to Rack 1 Place the UPS flat and press the key shown INSTALLING DVR AND DVD MODELS IN RACK CABINET The DVR and DVD models can be installed in a 19 rack cabinet The installation procedure is described below 1 Align and screw the handles onto the sides of the UPS i gout mcm L p ir LI a E uta Fe D ns ge Fa le m ge E E Hr ia zt a u 2 s F HE i io 2 r L 3 Insert the UPS on the mounted guides and secure it to the cabinet using the screws aA C WASA VAN
Download Pdf Manuals
Related Search