Data Video Projector User`s Manual (Concise)
Contents
1. rtt tee 2 Turning on the power 11 Entries and graphical symbols explanation 2 Adjusting the projector s elevator 12 Important safety instruction 2 Operation 12 Regulatory notices 3 Turning off the power 14 About Electro Magnetic Interference 3 Replacing the lamp 15 About Waste Electrical and Electronic Equipment 4 Cleaning and replacing the air filter 17 Contents of package 4 Caring for the mirror and lens 18 Arrangement c eene 5 Using the CD manual 19 Connecting with your devices 6 Specifications sssssssss 20 Connecting power supply 8 Troubleshooting Using the cable cover 9 Warranty and after service 21 Preparing for the remote control 10 403 8104WB 8105B 8106B 8109W 8115 CONCISE 00 First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows for safety purpose Please know their meanings beforehand and heed them AWARNING This entry warns of a risk of serious personal injury or even death ACAUTION This entry warns of a risk of personal injury or physical damage NOTICE This entry notices of fear of causing troubl2. Utilize the cable cover as the guard and blind for the connecting parts 1 Connect the signal cables and the power cord to the projector first ENGLISH iS Combine parts as shown in figure and assemble the cable cover Insert the three knobs on the cable cover into the three holes on the projector as shown in the figure Pass the cables through the holes on the bottom of the cable cover AGAUTION P Be careful not to pinch the cables in the cable cover to prevent damage to the cables Use the cable cover that is supplied with the projector Do not attempt any modifications to the cable cover Preparing for the remote control Please insert the batteries into the remote control before using it If the remote control starts to malfunction try to replace the batteries If you will not use the remote control for long period remove the batteries from the remote control and store them in a safe place 1 1 Holding the hook part of the battery cover remove it NS 2 Align and insert the two AA batteries HITACHI MAXELL ENERGY Part No LR6 or R6P according to their plus and minus terminals as indicated in the remote control 3 Replace the battery cover in the direction of the arrow and snap it back into place NOTE Remote sensor Try changing the batteries when the remote control malfunctions This remote control works with the remote sensors on the projector using infrared light Class
3. 1 LED The active sensor senses the remote control signal assigned within 60 degrees to right and left and within 3 meters For details see the Operating Guide in the CD Prevent the remote sensors from being hit by a strong ray It may cause malfunction of the projector and remote control ANWARNING P Always handle the batteries with care and use them only as directed Improper use may result in battery explosion cracking or leakage which could result in fire injury and or pollution of the surrounding environment Be sure to use only the batteries specified Do not use batteries of different types at the same time Do not mix a new battery with used one Make sure the plus and minus terminals are correctly aligned when loading a battery Keep a battery away from children and pets Do not recharge short circuit solder or disassemble a battery Do not place a battery in a fire or water Keep batteries in a dark cool and dry place If you observe battery leakage wipe out the leakage and then replace a battery If the leakage adheres to your body or clothes rinse well with water immediately Obey the local laws on disposing the battery Turning on the power STANDBY ON button 1 Make sure that the power cord is firmly indicator and correctly connected to the projector id jn l and the outlet d C Oro Make sure that the POWER indicator is 0 steady orange 3 Confirm that there is nothing that the
4. QO eae Qr O JONTOR OU i OUO C F 5 Computer Access point Aa LAN USBTYPEA RS 232C o Ve USB AR un wireless 3 D USB PEB HDMI COMPUTER IN2 COMPUTER IN1 adapter al J optional G I je log CN TE B s gt BEAN USB storage Dr device pe VIDEO AUDIO OUT AUDIO INS R C e AUDIOIN2 AUDIOINI MIC EE 2000 8 8 m 345 130 oo IP Ess a 7 ps s unit mm DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles IL 60174 800 676 2487 630 762 4032 Fax 630 584 5156 avservice dukane com www dukane com av
5. Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old used lamps this is a cause of breakage 16 Cleaning and replacing the air filter The air filter has two kinds of filters inside Please check and clean the air filter periodically When the indicators or a message prompts you to clean the air filter comply with it as soon as possible If the filters are damaged or heavily soiled replace them with the new ones To ar prepare the new filters make contact with your dealer and tell the following type number Type number UX37191 Filter set ENGLISH When you replace the lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector 3 4 Turn the projector off and unplug the power cord Allow the projector to sufficiently cool down Use a vacuum cleaner on and around the filter cover Slide the filter unit upward to take it off from the projector Filter cover Use a vacuum cleaner for the filter vent of the projector Take the fine meshed filter out while holding the filter cover It is recommended to leave the coarse meshed f R Ps Intake vent filter in the filter cover as it is Filter unit D Mose a Use a vacuum cleaner on both sides of the fine meshed ro filter while hold
6. have replaced the lamp for a suitable indication about the lamp 15 Replacing the lamp continued HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE AWARNING PThe projector uses a high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition if the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury and dust containing fine particles of glass to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put itin a trash Dispose of it in accordance with environmental laws For lamp recycling go to www lamprecycle org in the US For product disposal consult your local government agency or www eiae org in the US or www epsc ca in Canada For more information ask your dealer f the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass could damage the projector s internals or cause injury during handling So please do not try to clean the projector or replace the lamp yourself Disconnect If the lamp should break it will make a loud bang when it does ventilate th
7. lens door hits while opening Press the STANDBY ON button on the projector or the remote control The lens door opens the projection lamp lights up and the POWER indicator begins to blink green When the TANDBY ON power is completely on the indicator will stop blinking and light in steady green AWARNING P Never look into the projection lens or mirror while the projection lamp lights since the projection lamp ray may cause a trouble on your eyes gt Be careful not to pinch your finger with the lens door to prevent an injury Do not place the projector vertically with the lens door open as shown in the figure on the right It could cause malfunction or injury Tabletop use must be set up with the designated optional accessories Do not stand under the projector mounted on the wall or ceiling when its lens door is opening or closing Moreover do not look at the mirror when the lens door is opening or closing Never touch a lens door or mirror If the mirror is broken the projected image will be distorted Close the lens door and contact your dealer NOTE Please power on the projector prior to the connected devices The projector has the DIRECT POWER ON function which can make the projector automatically turn on For more information please see the Operating Guide in the CD ENGLISH iz Adjusting the projector s elevator The projector has Front foot for inclinations and Rear foot for h
8. web address where you may find the latest information for this projector DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles IL 60174 800 676 2487 630 762 4032 Fax 630 584 5156 avservice dukane com www dukane com av NOTE The information in this manual is subject to change without notice The illustrations in this manual are for illustrative purposes They may differ slightly from your projector The manufacturer assumes no responsibility for any errors that may appear in this manual The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment Mac Macintosh and Mac OS are registered trademarks of Apple Inc Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated Microsoft Internet explorer Windows Windows NT and Windows Vista are registered trademarks of Microsoft Corporation in the U S and or other countries HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Blu ray Disc and Blu ray are trademarks of Blu ray Disc Association All other trademarks are the properties of their respective owners End User License Agreement for the Projector Software Software in the projector consists of the plural number of independent software modules and there exist o
9. 00 120V 370 W AC 220 240V 350W 8115 8109W 0 40 C Operating Temperature range 35 40 C The brightness of the lamp is reduced automatically 345 W x 85 H x 303 D mm Size Not including protruding parts Refer to figure F 6 at the back of this manual Weight mass approx 3 8 kg Computer input port HDMI input port COMPUTER IN1 HDMI connector x1 D sub 15 pin mini x1 Audio input output port COMPUTER IN2 AUDIO IN1 Stereo mini x1 D sub 15 pin mini x1 AUDIO IN2 Stereo mini x1 Computer output port AUDIO IN3 R L Ports MONITOR OUT AUDIO OUT R L D sub 15 pin mini x1 Others Video input port USB TYPEA mini DIN 4 pin x1 USB TYPE B um Mono mini x1 Lamp 456 8104WB lt 8105B 8106B 8104WB gt 456 8109W lt 8115 8109W gt Filter set UX37191 Optional parts Tabletop use kit TT 251 Laser remote control RC R008 USB wirelessless adapter USB WL 11N For more information please consult your dealer 20 Troubleshooting Warranty and after service If an abnormal operation such as smoke strange odor or excessive sound should occur stop using the projector immediately Otherwise if a problem occurs with the projector first refer to Troubleshooting of Operating Guide and Network Guide and run through the suggested checks If this does not resolve the problem please consult your dealer or service company They will tell you what warranty condition is applied Please check the following
10. CAUTION P If you wish to have a blank screen while the projector s lamp is on use the BLANK function see the Operating Guide Any other method of blocking the projection light such as attaching something to the lens or placing something in front of the lens may cause the damage to the projector continued on next page Operation continued NOTE The ASPECT button does not work when no proper signal is inputted For details see the Operating Guide in the CD There may be some noise and or the screen may flicker for a moment when an operation is made This is not a malfunction Turning off the power Press the STANDBY ON button on the projector or the remote control The message Power off will appear on the screen for about 5 seconds 2 Confirm that there is nothing that the lens door hits while closing Press the STANDBY ON button again while the message appears The projector lamp will go off and the POWER indicator will begin blinking in orange The lens door will close right after the lamp goes off However to maintain better picture quality the lens door will close after the lamp has been cooled down when the projector is installed upside down such as in ceiling mount installation Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete Do not turn the projector on for about 10 minutes or more after turning it off Also do not turn the projector off s
11. THE ALL NEW DUKANE Education Presentation Inspiration Data Video Projector User s Manual Concise MODELS 8104WB 8105B 8106B 8109W 8115 Information in this Guide may change due to product improvements To obtain the latest manuals literature and software please visit the Dukane web site at www dukane com av and look at the specific model SUPPORT or DOWNLOADS section DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles IL 60174 800 676 2487 630 762 4032 Fax 630 584 5156 avservice dukane com www dukane com av 403 8104WB 8105B 8106B 8109W 8115 CONCISE 00 Projector DUKANE 8105B 8106B 8104WB 8115 8109W ENGLISH S User s Manual concise Thank you for purchasing this projector Please read through this manual before using this product in order to use safely and utilize well the product AWARNING Before using this product be sure to read all manuals for this product See the Using the CD manual 1119 to read the manuals in the CD After reading them store them in a safe place for future reference gt Heed all the warnings and cautions in the manuals or on the product gt Follow all the instructions in the manuals or on the product NOTE In this manual unless any comments are accompanied the manuals means all the documents provided with this product and the product means this projector and all the accessories came with the projector Contents First of all
12. ake care not to put in the mouth Heat may build up in the USB wireless adapter to avoid possible burns disconnect the projector power cord for more than 5min before touching it Connecting power supply 1 Put the connector of the power cord into the AC IN AC inlet of the projector 2 Firmly plug the power cord s plug into the outlet In a couple of seconds after the power supply connection the POWER indicator will light up in steady orange AC IN Please remember that when the DIRECT POWER ON function activated the connection of the power supply make the projector turn on Power cord AWARNING PPlease use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and or electrical shock Do not touch the power cord with a wet hand Only use the power cord that came with the projector If it is damaged consult your dealer to get a new one Never modify the power cord Only plug the power cord into an outlet whose voltage is matched to the power cord The power outlet should be close to the projector and easily accessible Remove the power cord for complete separation Do not distribute the power supply to multiple devices Doing so may overload the outlet and connectors loosen the connection or result in fire electric shock or other accidents NOTICE P This product is also designed for IT power systems with a phase to phase voltage of 220 to 240 V Using the cable cover
13. also ask the dealer to replace the lamp In case of replacement by yourself follow the following procedure 3 Loosen the screw marked by arrow of the lamp cover and then slide and lift the lamp cover to the Side to remove it 4 Loosen the 2 screws marked by arrow of the lamp and slowly pick up the lamp by the handle Never loosen any other screws 5 Insert the new lamp and retighten firmly the ENGLISH 2 screws of the lamp that are loosened in the previous process to lock it in place While putting the interlocking parts of the lamp cover and the projector together slide the lamp cover back in place Then firmly fasten the screw of the lamp cover Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu 1 Press the MENU button to display a menu 2 Point at the ADVANCED MENU in the menu using the V A button then press the P button 3 Point at the OPTION in the left column of the menu using the V A button then press the button SA 4 Point at the LAMP TIME using the V A button then Handle Oo press the button A dialog will appear 5 Press the button to select OK on the dialog It performs resetting the lamp time N AGAUTION PDo not touch any inner space of the projector while the lamp is taken out NOTE Please reset the lamp time only when you
14. aring for the projection mirror and lens turn the projector off and unplug the power cord then cool the projector sufficiently gt Do not use a vacuum cleaner to clean the projection mirror or lens since it might give some damage Do not use cleaners or chemicals other than those specified in this manual Pay special attention to the mirror and lens as these materials could cause serious damage to either NCAUTION P Be careful not to pinch your finger with the lens door to prevent an injury Using the CD manual The other manuals for this product are written into the included CD ROM titled User s Manual detailed Before using the CD ROM please read the following a to ensure the proper use E System requirements 5 The system for using the CD ROM requires the following z Windows OS Microsoft Windows XP Windows Vista Windows 7 or later Macintosh OS Mac OS 10 2 or later CD ROM DVD ROM drive Applications Microsoft Internet Explorer 6 0 or later Adobe Acrobat Reader 8 0 or later E How to use the CD 1 Insert CD into computer s CD ROM DVD ROM drive Windows In a while Web browser automatically starts Start up window comes up Macintosh 1 Double click on the PROJECTORS icon appeared on the desktop screen 2 When main htm file is clicked Web browser will start and Initial window will appear 2 Click the model name of your projector first and then click language yo
15. cusing Use the FOCUS and FOCUS buttons on the projector or remote control to adjust the screen focus ASPECT button VOLUME button Selecting an aspect ratio KEYSTONE button ENGLISH EG Each time you press the ASPECT button on the remote control it switches the aspect ratio of the image in turn D ZOOM button D ZOOM button FOCUS button FOCUS button POSITION button Zooming Use the D ZOOM and D ZOOM buttons on the remote control to adjust the screen size Adjusting the picture position After pressing the POSITION button on the remote control use the A V lt and buttons Press the POSITION button again to finish this operation Correcting distortion Press the KEYSTONE button on the remote control A dialog will appear on the screen to aid you in correcting the distortion Use the A V cursor buttons to select MANUAL or PERFECT FIT operation and press the button to perform the following MANUAL displays a dialog for keystone correction PERFECT FIT displays a dialog for adjusting the shape of the projected image in each of the corners and sides Use the cursor buttons according to the dialog checking the image Press the KEYSTONE button again to finish this operation Adjusting the volume Use the VOLUME buttons to adjust the volume Muting the sound Press the MUTE button on the remote control To restore the sound press the MUTE or VOLUME button A
16. e Do not place the product unstably Place the projector so that it does not protrude from the surface where the projector is placed on Remove all the attachments including the power cord and cables from the projector when carrying the projector Never look into the projection lens or mirror while the projection lamp lights since the projection lamp ray may cause a trouble on your eyes Do not approach the lamp cover and the exhaust vents while the projection lamp is on Also after the lamp goes out do not approach them for a while since too hot Regulatory notices About Electro Magnetic Interference In CANADA This Class B digital apparatus complies with Canadian ICES 003 In the US and other places where the FCC regulations are applicable Declaration of Conformity Trade name HITACHI DUKANE Model Number CP A222WN 8105B CP A302WN 8106B CP AW252WN 8104WB CP A352WN 8115 CP AW312WN 8109W Responsible Party Hitachi America Ltd Address 900 Hitachi way Chula Vista CA 91914 3556 U S A Telephone Number 1 800 448 2244 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of
17. e Important safety instruction The followings are important instructions for safely using the product Be sure to follow them always when handling the product The manufacturer assumes no responsibility for any damage caused by mishandling that is beyond normal usage defined in these manuals of this projector AWARNING P Never use the product in or after an abnormality ex giving off smoke smelling strange took a liquid or an object inside broken etc If an abnormality should occur unplug the projector urgently gt Situate the product away from children and pets Do not use the product when there is fear of a thunderbolt gt Unplug the projector from the power outlet if the projector is not used for the time being Do not open or remove any portion of the product unless the manuals direct it For internal maintenance leave it to your dealer or their service personnel Use only the accessories specified or recommended by the manufacturer gt Do not modify the projector or accessories gt Do not let any things or any liquids enter to the inside of the product Do not wet the product Do not place the projector where any oils such as cooking or machine oil are used Oil may harm the product resulting in malfunction or falling from the mounted position Do not apply a shock or pressure to this product Do not place the product on an unstable place such as the uneven surface or the leaned tabl
18. e the plug room well and make sure not to inhale the gas or fine particles that come out from the i i power from the projector s vent holes and not to get them into your eyes or mouth outlet Before replacing the lamp turn the projector off and unplug the power cord then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp Never unscrew except the appointed marked by an arrow screws Do not open the lamp cover while the projector is mounted on a wall or ceiling This is dangerous since if the lamp s bulb has broken the shards will fall out Q when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or injury Use only the lamp of the specified type Use of a lamp that does not meet the lamp specifications for this model could cause a fire damage or shorten the life of this product If the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this aD happens consult your local dealer or a service representative e Handle with care jolting or scratching could cause the lamp bulb to burst during use
19. ector be sure to use the REMOVE USB function on the thumbnail screen to secure your data Before you insert or pull out the USB wireless adapter from the projector turn off the power of the projector and pull out the power cord s plug from the outlet Do not touch the USB wireless adapter while the projector is receiving AC power continued on next page Connecting with your devices continued NOTICE Use the cables with straight plugs not L shaped ones as the input ports of the projector are recessed NOTE If a loud feedback noise is produced from the speaker move the microphone away from the speaker ENGLISH This projector doesn t support plug in power for the microphone The COMPUTER IN1 2 port can support a component signal also The specific adapter or the specific cable is reguired for a component video input to the projector Fastening the adapter cover Use the supplied adapter cover to prevent the USB wireless adapter optional from coming off easily and prevention from burn injury 1 Loosen the screw marked with triangle on the bottom left of the USB TYPE A port 2 Insert the tab of the cover into the hole at the upper right of the USB TYPE A port in the direction of the arrow 3 Align the screw holes on the projector and the cover Then insert the screw removed from the projector into the hole and tighten the screw AWARNING P Keep small parts away from children and pets T
20. hortly after turning it on Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp STANDBY ON button AWARNING P Be careful not to pinch your finger with the lens door to prevent an injury Do not touch around the lamp cover and the exhaust vents during use or just after use since it is too hot Remove the power cord for complete separation The power outlet should be close to the projector and easily accessible NOTE Please power off the projector after any connected devices are powered off This projector has the AUTO POWER OFF function that can make the projector turn off automatically For more information please see the Operating Guide in the CD Replacing the lamp A lamp has finite product life Using the lamp for long periods of time could cause the pictures darker or the color tone poor Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp make contact with your dealer and tell the lamp type number Type number 456 8104WB lt 8105B 8106B 8104WB gt Type number 456 8109W lt 8115 8109W gt 1 Turn the projector off and unplug the power cord lamp cover Allow the projector to cool for at least 45 minutes 2 Prepare a new lamp If the projector is mounted on a wall or ceiling or if the lamp has broken
21. ing it so it will not be sucked in Use a vacuum cleaner for the inside of the filter cover to clean up the coarse meshed filter If the filters are damaged or heavily soiled replace them with new ones Filter cover Put the fine meshed filter on the coarse meshed one turning its stitched side up D coarse meshed Put the filter unit back into the projector Filter fine meshed 9 Turn the projector on and reset the filter time using the SSO Stitched FILTER TIME item in the EASY MENU Sp side 1 Press the MENU button to display a menu 2 Point at the FILTER TIME using the V A button then press the button A dialog will appear 3 Press the gt button to select OK on the dialog It performs resetting the filter time AWARNING P Before taking care of the air filter make sure the power cable is not plugged in then allow the projector to cool sufficiently Use only the air filter of the specified type Do not use the projector without the air filter or the filter cover It could result in a fire or malfunction to the projector gt Clean the air filter periodically If the air filter becomes clogged by dust or the like internal temperatures rise and could cause a fire a burn or malfunction to the projector NOTE Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter The projector may display the message such a
22. o operate the equipment Regulatory notices continued About Waste Electrical and Electronic Equipment The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste but use the return and collection systems available If the batteries or accumulators included with this equipment display the chemical symbol Hg Cd or Pb then it means that the battery has a heavy metal content of more than 0 000596 Mercury or more than 0 00296 Cadmium or more than 0 00496 Lead Contents of package Your projector should come with the items shown below Check that all the items are included Require of your dealer immediately if any items are missing 1 Remote control with the two AA batteries 2 Power cord 3 Computer cable 4 Parts of cable cover 5 User s manuals Book x1 CD x1 6 7 8 9 Security label Application CD Wall mount unit and User s manual Adapter cover 8105B 8106B 8104WB 8115 8109W does not bundle them AWARNING PDo not attempt to install the projector yourself Have your dealer or service center handle all installation work Note that manufacturer will accept no liability whatsoever for accidents or injuries resulting from an incorrect installa
23. orizontals Spacers on the each elevator foot are installed at the time of shipment and projector is in a condition to be able to just project If necessary detach the spacer and the elevator Rear foot Front foot t amp l GJE en z a 11 1 Spacer Rear foot Spacer Small Front foot AWARNING P Keep the spacers away from children and pets Be careful not to let them swallow the spacers If swallowed consult a physician immediately for emergency treatment NOTE The adjustment angle can be adjusted up to plus or minus 1 each of Front and Rear foot After the foot is adjusted it is possible to return it to the state of the shipment with a spacer Install Large on the Front foot and Small on the Rear foot of the spacer If change the setting place of the projector it will recommend keep and reuse the spacers Operation INPUT button COMPUTER button FOCUS button VIDEO button FOCUS button Displaying and switching the image Press the INPUT button on the projector Each time you press the button the projector switches its input port in turn You can also use the remote control to select an input signal Press the VIDEO button for selecting an input signal from the HDMI S VIDEO or VIDEO port or the COMPUTER button for selecting an input signal from the COMPUTER IN1 COMPUTER IN2 LAN USB TYPE A or USB TYPE B port 12 Fo
24. own screen may cause serious distortion of a projected image A hard screen such as a board screen is recommended for use with this projector A high gain screen such as a bead screen that has narrow viewing angle is not suitable for this projector A low gain screen around 1 0 such as a matte screen that has wide viewing angle is recommended for use with this projector Ascreen with a weave pattern may cause moir on the projected image which is not a failure of the projector A screen that has less moir effects is recommended for use with this projector AWARNING gt Install the projector in a stable horizontal position Place the projector in a cool place and ensure that there is sufficient ventilation Keep a space of 30 cm or more between the sides of the projector and other objects such as walls Do not place or attach anything that would block the lens or vent holes Do not place the projector where the air from an air conditioner or similar unit will blow on it directly Do not place the projector anyplace where it may get wet Use only the mounting accessories the manufacturer specified and leave installing and removing the projector with the mounting accessories to the service personnel Read and keep the user s manual of the mounting accessories used AGAUTION P Avoid placing the projector in smoky humid or dusty place gt Position the projector to prevent light from directly hitting the projector s remote senso
25. r gt If the projector is used at an altitude of about 1600 m or higher set ALTITUDE of the SERVICE item in the OPTION menu to HIGH Otherwise set it to NORMAL If the projector is used with a wrong setting it may cause damage to the projector itself or the parts inside NOTE The projector may make a rattling sound when tilted moved or shaken since a flap to control the air flow inside of the projector has moved Be aware that this is not a failure or malfunction Arrangement continued Connecting with your devices Be sure to read the manuals for devices before connecting them to the projector Make sure that all the devices are suitable to be connected with this product and prepare the cables required to connect Refer to figures F 3 to F 5 at the back of this manual For details please see User s Manual Operating Guide and Network Guide 1119 21 When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in COMPUTER IN of the INPUT menu that port will accept component video signals To use network functions of the projector connect the LAN port with the computer s LAN port or with an access point that is connected to the computer with wireless LAN using a LAN cable If you insert a USB storage device such as a USB memory into the USB TYPE A port and select the port as the input source you can view images stored in the device You can connect a dynamic microphone to the MIC port wi
26. s the CHECK THE AIR FLOW or turn off the projector to prevent the internal heat level rising 17 Caring for the mirror and lens If the projection mirror or lens is flawed soiled or fogged it could cause deterioration of display quality Please take care of the mirror and lens being cautious of handling 1 Turn the projector off and unplug the power cord from the power outlet And cool the projector down by leaving it for a while as it is 2 The lens door can be opened manually Please hold both side of the lens door and slowly open it until it is locked with clicking sound 3 Use an air blower to blow away dust on the lens and on the mirror before wiping Wipe softly the mirror and lens with a damped soft cleaning cloth for lens on the market being careful not to give any damage on the mirror and lens 4 To close the lens door properly please take the following procedure 1 Insert the power cord with the lens door opened 2 The power indicator will light in orange and the lens door closes automatically Do not touch the lens door when the door is closing Do not allow anything to obstruct the lens door Cleaning cloth NOTE When the lens door is closed manually it may not shut properly The lens door may not close when the LENS DOOR LOCK function of the SERVICE item in the OPTION menu is set to ON For more information please see the Operating Guide on the CD AN WARNING pb Before c
27. th a 3 5 mm mini plug In that case the built in soeaker outputs the sound from the microphone even while the sound from the projector is output AWARNING P Use only the appropriate accessories Otherwise it could cause a fire or damage to the device and the projector Use only the accessories specified or recommended by the projector s manufacturer Consult your dealer when the required accessory did not come with the product or the accessory is damaged It may be regulated under some standard For a cable with a core at only one end connect the end with the core to the projector That may be required by EMI regulations Neither disassemble nor modify the projector and the accessories Do not use the damaged accessory Be careful not to damage the accessories Route a cable so that it is neither stepped on nor pinched out AGAUTION PDo not turn on or off the projector while connected to a device in operation unless that is directed in the manual of the device Be careful not to mistakenly connect a connector to a wrong port Before connecting the projector to a network be sure to obtain the consent of the administrator of the network Do not connect the LAN port to any network that might have the excessive voltage The designated USB wireless adapter that is sold as an option is reguired to use the wireless network function of this projector Before removing the USB storage device from the port of the proj
28. the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help ENGLISH e INSTRUCTIONS TO USERS This equipment complies with the requirements of FCC Federal Communication Commission equipment provided that the following conditions are met Some cables have to be used with the core set Use the accessory cable or a designated type cable for the connection For cables that have a core only at one end connect the core to the projector CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority t
29. tion or improper use NOTE Keep the original packing materials for future reshipment Be sure to use the original packing materials when moving the projector Use special caution for the lens Arrangement Refer to tables T 1 or T 2 and figures F 1 and F 2 at the end of this manual to determine the screen size and projection distance The values shown in the table are calculated for a full size screen 8 Screen size diagonal 1 62 Projection distance 896 D 2 Screen height 8 ENGLISH For the case of installation in special conditions such as on the wall or ceiling the specified mounting accessories 120 and service may be required Tabletop use must be set up with the designated optional accessories 320 Before installing the projector consult your dealer about your installation The screen position may shift after installation if the projector is mounted on locations such as the wall or ceiling due to the flexibility of the plastic projector body If readjustment is necessary consult with your dealer or service personnel The projected image position and or focus may change during warm up approx 30 minutes after the lamp is turned on or when the ambient conditions change Readjust the image position and or focus as necessary Since the projector features an ultra short throw be aware that it is required to select a screen carefully to have better performance A soft screen such as a pull d
30. u want from the displayed list The User s manual detailed will open ACAUTION P Only use the CD ROM in a computer CD DVD drive The CD ROM is designed for computer use only NEVER INSERT THE CD ROM INTO A NON COMPUTER CD DVD PLAYER Inserting the CD ROM into an incompatible CD DVD drive may produce a loud noise which in turn MAY RESULT IN EAR AND SPEAKER DAMAGE After using CD ROM please put it into CD case and keep it Please keep the CD neither in direct sunlight nor in a high temperature and high humidity environment NOTE The information in the CD ROM is subject to change without notice No responsibility is taken for any obstacle and defect to hardware and software of your computer as a result of the use of the CD ROM All or Any part of the information in the CD ROM must not be copied reproduced or republished without notice to our company Specifications Item Specification Product name Liquid crystal projector Liquid Crystal Panel 786 432 pixels 1024 horizontal x 768 vertical 1 024 000 pixels 1280 horizontal x 800 vertical Lam 215W UHP 8105B 8106B 8104WB P 250W UHP 8115 8109W Speaker 10W 8105B P 16W 8106B 8104WB 8115 8109W AC 100 120V 3 3A AC 220 240V 1 6A 8105B Power supply AC 100 120V 3 4A AC 220 240V 1 7A 8106B 8104WB AC 100 120V 3 8A AC 220 240V 1 8A 8115 8109W AC 100 120V 320 W AC 220 240V 300W 8105B Power consumption AC 100 120V 330 W AC 220 240V 310W 8106B 8104WB AC 1
31. ur copyright or and third party copyrights for each of such software modules Be sure to read End User License Agreement for the Projector Software which is separated document in the CD This page left intentionally blank 22 On a horizontal surface Mounted on the wall or ceiling DEN 8105B 8106B 8115 1024 x 768 890 Screen size Projection distance Screen height diagonal a ED 2 m inch m inch 89 0 531 20 9 0 352 13 9 1 571 61 9 8104WB 8109W 1280 x 800 2896 NUM Projection distance egna 60 4 7 0 426 16 8 0 295 11 6 1 102 43 4 70 7 4 0 494 19 5 0 332 13 1 1 274 50 2 10 90 2 17 5 Computer VCR DVD Blu ray Disc player ED fen gt al FSC F 110 oianv Oectc su Speakers Microphone with an amplifier system Monitor USB TYPEB _ HDMI ME JTER IN2 OMPL TER IN1 iz ein da 5 A 16 S VIDEC AUDIO OUT AUDIO INS
Download Pdf Manuals
Related Search