Home

SANAV MU-201 GPS/GPRS Nano Tracker User Manual

1. MNC97 Mobile Network Code MNC is used in combination with MCC to uniquely identify a mobile phone operator carrier using the GSM networks and some satellite mobile networks LAC51145 Location Area Code A location area is a set of base stations that are grouped together to optimize signaling Typically tens or even hundreds of base stations share a single Base Station Controller BSC in GSM the intelligence behind the base stations To each location area a unique number called a location area code is assigned The location area code is broadcast by each base station known as a base transceiver station BTS in GSM at regular intervals CI D16012 Cell Identity For BTS identification 58 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Appendix 1 Tracker Event List This table shows the different events messages sent from the device Basically there are more than 10 different situations that trigger the device to respond its position and tracker status messages as the following Note Any event marks with letter B represents data which was not able to send to assigned route immediately due to priority or mobile network service issue The data will be sent after the issues are cleared Event Description AUTO BAUTO When the device is set to report to assigned route in a given period of time it will send a report automatically w
2. Enable and trigger the event when the tracker is outside of the Geo Fence Enable and trigger the event when the tracker is inside of the Geo Fence Enable and trigger the event when the tracker is either outside or inside of the Geo Fence Table Geo Fence Coordinate Setup Format Description 42 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Situation Response Success lt OK gt GF ONgf1 SETUP V4 172 100 lt OK gt GF OFFgf1 SETUP V4 172 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 172 100 Table Geo Fence Coordinates Setup Response Description 43 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Enable Geo Fence User can enable or disable the Geo Fence detection by this short command without inputting longitude and latitude if the coordinates are predefined Setup Format username Password Function Mode Parameter Command username 0000 gf1 1 SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode gfx defines the Geo Fence setup mode User can input gf1 gf2 gf3 gf4 gf10 to define each Geo Fence range There a
3. The write command for sensitivity setting Sensitivity Level Most vibration sensitivity Less vibration sensitivity Least vibration sensitivity To define if the device stops for how long will be counted as stop There are 60 120 180 240 300 second steps setting End sign Table Vibration Sensitivity Setup Format Description Situation Message Reply Setup Succeeds lt OK gt VS Write V5 SHOW V3 937 76 Emergency Mode lt FAIL gt PANIC ON Command not Allow V3 937 76 Table Vibration Sensitivity Setup Response Description 39 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Over Speed GPS receivers calculate the speed using algorithms in the Kalman filter Most receivers compute speed by a combination of movement per unit time and computing the Doppler shift in the pseudo range signals from the satellites MU 201 provides Over Speed Detection It will send an Over Speed report when GPS module calculates the speed value is greater then the defined speed limit Over Speed function consumes more power since the GPS module calculates the speed all the time once the Over Speed function is enabled Setup Format username Password Function Mode on off Command username 0000 speed on SMS COTA Command Description Start sign username Default ID of the
4. 14 Table URL or IP Setup Response Description Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up TCP UDP Server Address User can use IP address setup command to indicate the device transmit GPS GPRMC positioning data to a specified TCP or UDP protocol based server for real time tracking Entering the SMS command as the following allows user to change the address to specified IP and port The IP address will be assigned to receive the GPS data sent by the device Setup Format username Password Function Mode TCP UDP server address Command username 0000 18 220 128 123 1 7878 Or username 0000 18 icare u com tw 12345 SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 18 defines the TCP UDP Server Address setup mode 220 128 123 1 7878 TCP UDP Server Address and Port Domain name End sign Table Server Address Setup Format Description Situation Message Reply Setup Succeeds lt OK gt TCP UDP URL setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Server Address Setup Response Description 15 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 2
5. Situation Message Reply lt OK gt Monitor mode 0 1 auto answer call V3 793 56 Setup Succeeds lt OK gt Monitor mode 2 reply to caller V3 793 56 lt OK gt Monitor mode 3 reply by router V4 156 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Answer Call Mode Setup Response Description 19 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up SOS Phone Book Use this SMS COTA command to define the SOS cellular number by following the format below The device will first send 1 SOS event alarm report to all number in the phone book and then make a phone call to the SOS phone number immediately Setup Format username Password Function Mode SOS Phone Command username 0000 sosphone 886123456789 Note Add or not add the sign in front of the cellular phone number s are both acceptable while the sign should precede the international call prefixes SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode sosphone defines the SOS Phone Book setup mode 886123456789 SOS Phone number Situation End sign Table SOS Phone Book Setup Format Description Me
6. Chinese PRC zh hk Chinese Hong Kong SAR zh sg Chinese Singapore hr Croatian cs Czech da Danish nl Dutch Standard nl be Dutch Belgium en English len us English United States E English United Kingdom en au English Australia en ca English Canada en nz English New Zealand en ie English Ireland en za English South Africa en jm English Jamaica en English Caribbean en bz English Belize en tt English Trinidad et Estonian fo Faeroese fa Farsi fi Finnish fr French Standard fr be French Belgium fr ca French Canada fr ch French Switzerland fr lu French Luxembourg gd Gaelic Scotland ga Irish de German Standard de ch German Switzerland de at German Austria de lu German Luxembourg de li German Liechtenstein el Greek he Hebrew hi Hindi hu Hungarian is Icelandic id Indonesian it Italian Standard it ch Italian Switzerland ja Japanese ko Korean ko Korean Johab 33 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Code Country Region Code Country Region Iv Latvian It Lithuanian mk Macedonian FYROM ms Malaysian mt Maltese no Norwegian Bokmal no Norwegian Nynorsk pl Polish pt br Portuguese Brazil pt Portuguese Portugal rm Rhaeto Romanic ro Romanian ro mo Romanian Republic of Moldova ru Russian ru m
7. This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation SAN JOSE TECHNOLOGY I NC 11F No 2 Sec 4 Jhongyang Rd Tucheng District New Taipei City 236 Taiwan R O C TEL 886 2 22694456 FAX 886 2 22694451 http www sanav com Technical Support jacky sun sanav com 65 Copyright 2011 San Jose Technology Inc All Rights Reserved
8. 1 DISABLE ON 0030 2 DISABLE OFF 0645 3 DISABLE ON 1200 4 DISABLE OFF 18 30 V3 839 62 lt OK gt Schedule EnableSP State 1 ENABLE ON 0030 2 ENABLE OFF 0645 3 ENABLE ON 1200 4 ENABLE OFF 1830 V 3 839 62 lt OK gt Schedule SetupSP State 1 ENABLE ON 0030 2 ENABLE OFF 0645 3 ENABLE ON 1200 4 DISABLE OFF 1830 V3 839 62 Table Power OFF Message Setup Description Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Request Battery Voltage User can check the current battery voltage of the device by sending the following command Command battery Note For the example from Message Reply we found that there are 2 voltage measurements 3 826V and 3 793V The voltage shown will be different because 3 826V is detected voltage and 3 793V is instantaneous voltage when sending the message the voltage will be dropped a little for a while when sending So 3 826V will be more precise measurement SMS COTA Command Description Start sign battery Mode battery defines Battery Check mode lend sign Table Battery Voltage Check Format Description Situation Message Reply Setup Succeeds lt OK gt Vol V3 826 ADC 688 500000 V3 793 56 Table Battery Voltage Check Response Description 54 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Voltage Percentage The
9. 3 793 56 IMEI 135790246811220 amp rmc GPRMC 034429 00 V 2457 81213 N 12125 53903 E 0 189 140211 A 7B SOS 3 793 V 56 IMEI 135790246811220 amp rmc GPRMC 165724 00 V 2459 57367 N 12126 02097 E 0 671 182 53 180211 A 6B AUT 0 3 676V 56 LP IMEI 135790246811220 amp rmc GPRMC 172827 00 V 2459 56287 N 12126 03198 E 0 733 342 42 180211 A 69 3 793V 56 LP Device BATTERY LOW IMEI 555444333222111 amp rmc GPRMC 030930 00 V 2457 81198 N 12125 53663 E 0 161 210211 A 73 GFIN 1 3 793V 56 IMEI 135790246811220 amp rmc GPRMC 105735 00 V 2459 34799 N 12125 92549 E 5 747 34 34 180211 A 5D GOU T 2 3 793V 56 Note The A is the GPRMC sentence indicates the GPS status which is GPS fixed If the GPS is not fixed letter V will substitute the letter A 61 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual GPRMC Data Output Format SMS 1 Upload the data when GPS is fixed When execute the Auto Report according to the settings with a GPS fixed MU 201 will upload the data to SMS The data format will be like the following Format username GPRMC UTC Time Fix Status gt lt Latitude gt lt Longitude gt lt Speed gt lt Direction gt lt Date gt lt Checksum gt lt Tracker Event gt lt Battery Voltage gt lt Battery Voltage gt Example username GPRMC 031516 00 4 2457 81067 N 12125 53896 E 0 216 274 31 140211 A
10. 32333 E 1 015 128 84 100312 A 66 AUTO V3 793 56 Address message sentence example No 36 Zhongshan Rd Tucheng District Xinbei Taiwan 236 SMS COTA Command Description username Default ID of MU 58 If you have changed the Username please use the updated one Default password If you have changed the password please use the updated one Mode google defines the Google Map Address setup mode google hyper link OFF addr OFF google hyper link ON addr OFF google hyper link OFF addr ON google hyper link ON addr ON End sign Table Google Map Address Setup Format Description 30 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Situation Message Reply lt OK gt google hyper link OFF addr OFF V4 022 88 OK google hyper link ON addr OFF V4 022 88 Setup Succeeds OK google hyper link OFF addr ON V4 097 99 lt OK gt google hyper link ON addr ON V4 096 99 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 133 100 Table Google Map Address Setup Response Description 31 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Address Language The user can change the SMS polling address language by setting language codes The default address language is in en us English United States the user can send the following comman
11. Voltage Percentage is a simple device remained battery gauge indicator The command is used to enable disable voltage in percentage display information at the last of GPRMC sentence Setup format username Password Function Mode on off Command username 0000 pv on SMS COTA Command Description Start sign Username Default ID of MU 201 If you have changed the Username please use the updated one 0000 Default password If you have changed the password please use the updated one pv Mode pv defines Voltage Percentage ON OFF mode on on Enable voltage in percentage display information off Disable voltage in percentage display information End sign Table Voltage Percentage Setup Format Description Situation Message Reply lt OK gt PV ON V3 891 70 Setup Succeeds lt OK gt PV OFF V3 891 Emergency Mode lt FAIL gt PANIC ON Command not Allow V3 890 70 Table Voltage Percentage Setup Response Description 55 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Reset to Default Setting Use this command to reset the device to default factory setting It will recover all the current parameters to default values includes username and password Setup Format username Password Function Mode Command username 0000 9 SMS COTA Command Description
12. amp rmc GPRMC 034429 00 A 2457 81213 N 12125 53903 E 0 189 140211 A 7B SOS 3 934 V 3 793 56 IMEI 135790246811220 amp rmc GPRMC 165724 00 A 2459 57367 N 12126 02097 E 0 671 182 53 180211 A 6B AU T0 3 793 56 LP IMEI 135790246811220 amp rmc GPRMC 172827 00 A 2459 56287 N 12126 03198 E 0 733 342 42 180211 A 69 3 793 56 LP Device BATTERY LOW IMEI 555444333222111 amp rmc GPRMC 030930 00 A 2457 81198 N 12125 53663 E 0 161 210211 A 73 GFIN 1 3 793 56 IMEI 135790246811220 amp rmc GPRMC 105735 00 A 2459 34799 N 12125 92549 E 5 747 34 34 180211 A 5D GOU T 2 3 793 56 60 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual 2 Upload the data when GPS is not fixed Example IMEI 135790246811220 amp rmc GPRMC 031516 00 V 2457 81067 N 12125 53896 E 0 216 274 31 140211 A 67 AU TO 3 978V IMEI 135790246811220 amp rmc GPRMC 032903 00 V 2457 81147 N 12125 53901 E 0 018 140211 A 71 POLL 3 79 3 56 IMEI 135790246811220 amp rmc GPRMC 032210 00 V 2457 81085 N 12125 53833 E 0 359 201 82 140211 A 66 AG F 3 793 56 IMEI 135790246811220 amp rmc GPRMC 033334 00 V 2457 81122 N 12125 53836 E 0 341 10 26 140211 A 5C MOV E 3 793 56 IMEI 135790246811220 amp rmc GPRMC 033624 00 V 2457 81222 N 12125 53939 E 0 039 140211 A 72 PARK is ON now 3 793 56 IMEI 135790246811220 amp rmc GPRMC 033725 00 V 2457 81143 N 12125 53902 E 0 183 140211 A 7E PARK is OFF now
13. hold for 3s again Park One Short Press to trigger SOS button Park Mode Exit from Park In Park mode SISANAV one short press again to exit Park Mode MU 201 LED Indication GSM Device Status Steady ON Steady ON Power ON then following then following Long Press Power key for 3s booting procedure booting procedure About 20s About 20s Power OFF Steady ON around 8s Steady ON around 8s Long Press Power key for 3s Than power off Than power off een RER EECHER GPS Status GPS is fixed Flash 5s meme PET eo NE NEN GSM Status Eos ce fnsosvece mmo semen gt veggen femme tent gt pf mseme DEER mmm ES EEE bee ES gt ee EL om kuene mm P ES NO SIM or Invalid SIM ERROR OFF OFF After Power On 3 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Top View Power button Turn ON OFF Press and hold for more than 3 seconds ON Both red LEDs steady ON OFF Both green amp blue LEDs steady ON Note Please insert SIM card BEFORE turning ON the device Bottom View Hidden Microphone For Overhearing Side View SIM Card Holder Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Insert SI M Card Please note the SIM Card direction Note Please make sure PIN Code function is disabled before inserting the SIM card C
14. only please send username 0000 speed on to activate the function SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one 0000 Default password If you have changed the password please use the updated one 11 Mode 11 defines the Overspeed setup mode 100 Speed Limit threshold Range 1 999 km Speed Unit per hour There are 3 speed units for calculation km kilometer hr mi miles hr nm nautical miles hr 10 Time Interval period of Over Speed Report 3 Times frequency of Over Speed Reports that will be sent automatically 5 Detection times x 3s In this case the device reports Over Speed if it detects continuous 5 times x 35 15 seconds Over Speed events End sign Table Over Speed Interval Setup Format Description Situation Message Reply Setup Succeeds lt OK gt Speed limit setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Over Speed Interval Response Description 41 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Geo Fence Coordinates A Geo Fence is a virtual perimeter for a real world geographic area Geo Fencing is a term utilized primarily in the corporations that refers to the practice of limiting mobile employees to a specific geographic location by tracki
15. power ON the device automatically without pressing Power Button when plugging into wall outlet Command autoon on SMS COTA Command Description Start sign Mode autoon defines the Power ON via Power Cord mode on Enable the AUTO ON function off Disable the AUTO ON function End sign Table AUTO ON Setup Description Situation Message Reply Setup Succeeds lt OK gt AUTOON ON V4 154 100 Table AUTO ON Setup Response Description 51 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Power OFF Message User can use the command to have the device send Power OFF report when pressing power button to turn OFF the device Therefore the device will be turned OFF for a while about 10 seconds when pressing power button Command poweroffsend on SMS COTA Command Description Start sign poweroffsend Mode poweroffsend defines the Power OFF message mode on Enable the power off message function Show report when turn off Disable the power off message function End sign Table Power OFF Message Setup Description Situation Message Reply Setup Succeeds lt OK gt POWEROFFSEND ON V4 169 100 Table Power OFF Message Setup Response Description 52 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Power ON OF
16. use the updated one Mode 16 defines the Move Interval setup mode Interval period of MOVE Report Maximum 65000 seconds Total number of MOVE reports 1 9998 times 9999 is infinite End sign Table Park Interval Setup Format Description Situation Message Reply Setup Succeeds lt OK gt Move setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Park Interval Setup Response Description 36 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Vibration Vibration sensor is embedded in the device User can use following commands to enable vibration detection If the Vibration is set the GPS module of the device will be in power save mode when the device stops moving for more than 3 minutes Since the device is in vibration detection mode it will always send the same longitude latitude coordinates GPRMC data thus the GPS module consumes no power to obtain data from the satellites and the device operation time will be extended Setup Format username Password Function Mode on off Command username 0000 vs on SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode vs d
17. 01 GPS GPRS Nano Tracker User Manual Set up Phone Book List There are three main purposes of Phone Book List setup 1 Backup Route As a backup route when the data is not able to send to the server The data will be sent to 1 cellular number PH 01 only 2 SOS Alarm Route When the device is in SOS mode it will send SOS event report to the phone numbers in the list 3 SMS Data Route When the data route is set to SMS the device will send GPRMC data to to 1 cellular number PH 01 only Use this SMS command to set up the cellular phone book Max of 3 numbers as the following format Setup Format username Password Function Mode PH 01 PH 02 PH 03 Command username 0000 5 886123456789 492234567890 866323456789 Note1 Add or not add the sign in front of the cellular phone numbers are both acceptable while the sign should precede the international call prefixes Note2 When the Phone Book is set and Security Phone Book is enabled the numbers will be considered as security numbers Only the security numbers are allowed to do the command setting and overhearing answer call from the device SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 5 defines the Phone Book List setup mode 8
18. 1 V4 00 1 Log Backup Mode features added 2 HDOP value added in GPRMC sentences Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Contents Document Amendments siseiscckccndesesxncesssstceussiaeeeedecssxscessbaneessaebeeesveweadeesaa C MU 201 Hardware General Introduction 1 PEER 1 Package OSES EE SEE EN diese 2 aream M nain tee oi ion 3 MU 201 LED Indicatigbls needed ae 3 Charging MIT EE 5 ENN 6 Command Setup f r MU Z20L EE 7 Change User y 8 Change Password rennene 9 Request IMEI Number E 10 Set up APN for GPRS e EE 11 Set up Route for Data Transmiseion enne nne 12 SES TE 14 Set up TCP UDP Server Address NEEN 15 Set up Phone BOLT see 16 Set up Security Phone Book LISE ua J ss 17 Enable Security Phone BOOK oae REFER dons die 18 Ser up Answer Call MOG EE 19 Set up SOS PHONE BOOK se 20 Set up SOS Event Report Interval sssssssssrrrssessnrrnressnrrnnnananrnnnesnnrnneenns 21 SOS Event Report T IDW Re 22 Stop SOS Report Exit from SOS Mode issue 23 Setup ALES EPLE 24 Auto Report BY DANE Sen 25 Auto Report by Stationary TIMES 22220 dE eee 26 Current Position Pollinq ii istis deere cided EEN ENNEN EE ENEE 28 SEL UP Polling FOT EL oe 29 Google MAP Report with Address rwranaunnnnnrnvenannnnnnenennnnnnnnnenennnnnnnnenennne 30 Set up Address Language issus AN NENNEN EEN ESO SEENEN EEN EENN 32 Language Codes Refer
19. 67 AUT0 3 793 56 username GPRMC 032903 00 4 2457 81147 N 12125 53901 E 0 018 140211 A 71 POLL 3 793 56 username GPRMC 032210 00 A 2457 81085 N 12125 53833 E 0 359 201 82 140211 A 66 AGF 3 793 56 username GPRMC 033334 00 A 2457 81122 N 12125 53836 E 0 341 10 26 140211 A 5C MOVE 3 793 56 username GPRMC 033624 00 A 2457 81222 N 12125 53939 E 0 039 140211 A 72 PARK is ON now 3 793 56 username GPRMC 033725 00 A 2457 81143 N 12125 53902 E 0 183 140211 A 7E PARK is OFF now 3 793 56 username GPRMC 034429 00 4 2457 81213 N 12125 53903 E 0 189 140211 A 7B S05 3 934V 3 793 56 username GPRMC 165724 00 A 2459 57367 N 12126 02097 E 0 671 182 53 180211 A 6B AUT0 3 793 56 LP username GPRMC 172827 00 A 2459 56287 N 12126 03198 E 0 733 342 42 180211 A 69 3 793 56 LP Device BATTERY LOW username GPRMC 030930 00 A 2457 81198 N 12125 53663 E 0 161 210211 A 73 GFIN 1 3 793 56 username GPRMC 105735 00 A 2459 34799 N 12125 92549 E 5 747 34 34 180211 A 5D GOUT 2 3 793 56 2 Uploading the data when GPS is not fixed Example username GPRMC 031516 00 V 2457 81067 N 12125 53896 E 0 216 274 31 140211 A 67 AUTO 3 793 56 username GPRMC 032903 00 V 2457 81147 N 12125 53901 E 0 018 140211 A 71 POLL 3 793 56 username GPRMC 032210 00 V 2457 81085 N 12125 53833 E 0 359 201 82 140211 A 66 AGF 3 793 56 username GPRMC 033334 00 V 2457 81122 N 12125 53836 E 0 341 10 26 140211 A 5C MOVE 3 793 56 use
20. 86123456789 1 cellular numbers PH 01 492234567890 2 cellular numbers PH 02 866323456789 3 cellular numbers PH 03 End sign Table Phone Book List Setup Format Description Situation Message Reply Setup Succeeds lt OK gt P1 0935304180 P2 P3 V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Phone Number List Setup Response Description 16 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Security Phone Book List Security Phone Number list allows limited administrators to manage and change the settings of the device When the Security Phone Numbers are set even the User Name and Password are correct if the setup number is not matched with the list the setup or any change will be invalid By the way only the administrators of the list are allowed to call the device for real time communication when the Security Phone Numbers are set Maximum 10 sets of numbers are available Setup Format username Password Function Mode Leif Phone number Command username 0000 secphone 1 886123456789 SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode secphone defines the Secu
21. Due to the functionalities of the devices are being developed and improved from time to time the change in the protocol specification and firmware functions are subjects to change without prior notice SANAV is obligated to modify all the documentation without the limitation of time frame A change notice shall be released to San Jose Technology Inc customers upon the completion of document modification San Jose Technology Inc products are not intended to be used as life support or rescue equipments San Jose Technology Inc is not liable for any loss or injury caused by using or referencing to any products Any possible means of using or integrating San Jose Technology Inc products shall be avoided Copyright Copyright 2011 San Jose Technology Inc All rights reserved The information in this publication is proprietary to San Jose Technology Inc No part of this publication may be used disclosed reproduced adapted translated stored in a retrieval system or transmitted in any form of or by any means electronic or mechanical for any purpose without the prior written permission of San Jose Technology Inc although every precaution has been taken in the preparation of this publication San Jose Technology Inc assumes no i responsibility for errors or omissions contained herein or ii liability for any damages resulting from the use of information contained herein Information in this publication is subject to change wit
22. F Schedule Use the command to set up the Power ON OFF Schedule per day of the device User can set the device when will be turned ON and when will be OFF There are totally 4 stages of a day can be scheduled The device still can be turned ON when the device is scheduled OFF Command username 0000 sp disable to disable all the 4 stages of the schedule username 0000 sp enable to enable all the 4 stages of the schedule username 0000 sp on 0000 off 1200 to turn on at 00 00 and turn off at 12 00 username 0000 sp on 0030 off 0645 0n 1200 dis 1830 to turn on at 00 30 turn off at 6 45 turn on again at 12 00 and disable the last stage that should be turned off at 18 30 SMS COTA Command Description Start sign Default ID of MU 201 If you have changed the Username please use the updated one Default password If you have changed the password please use the updated one Mode sp defines the Power Schedule mode disable dis to disable all the 4 stages of schedule To disable specified stage s of schedule to enable all the 4 stages of schedule to turn on the device automatically to turn off the device automatically The UTC time schedule to turn on or turn off the device Situation Setup Succeeds 1 Setup Succeeds 2 Setup Succeeds 3 53 End sign Table Power OFF Message Setup Description Message Reply lt OK gt Schedule DisableSP State
23. GSANAV SANAV MU 201 GPS GPRS Nano Tracker User Manual Revision 1 1 6 Revision Date 2012 08 01 August 2012 1 1 6 Copyright 2011 San Jose Technology Inc All Rights Reserved This document contains information that is the property of SANAV This document may not be copied reproduced reduced to any electronic medium or machine readable form or otherwise duplicated and the information herein may not be used disseminated or otherwise disclosed except with the prior written consent of SANAV GSANAV MU 201 GPS GPRS Nano Tracker User Manual MU 201 User Documentation Introduction SANAV MU 201 is a more compact version of focusing on the pets or asset tracking market Its location can be real time tracked through internet or specified terminals The user can communicate with the service server through GPRS GSM network transfer alarms of Emergency Geo fencing Remote Control and Lower power and record the tracking history stored in internal memory through USB or website This User Manual details the specification hardware introduction SMS commands and Tracker Status of MU 201 If you have any question about the operation of MU 201 please contact SANAV Customer Service jacky sun sanav com Disclaimer This document and all other related products such as device firmware and software is developed by San Jose Technology Inc thoroughly At the time of release it is most compatible with specified firmware version
24. IC ON Command not Allow V4 091 98 lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Transmission Route Setup Response Description 13 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV Set up URL MU 201 GPS GPRS Nano Tracker User Manual This SMS command instructs the device to transmit GPS GPRMC positioning data to a specified URL Uniform Resource Locator or IP address of HTTP protocol server for real time GPS tracking Entering the SMS command as the following allows user to changes the address to http www sanavtw com uploadM1 php The address will be assigned to receive the GPS data sent by the device Setup Format username Password Function Mode URL Command username 0000 4 http www sanavtw com uploadM1 php Note The URL should be less than 80 characteristics SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 4 defines the URL setup mode http www sanavtw com uploadM1 php URL of the HTTP server Situation End sign Table URL or IP Setup Format Description Message Reply Setup Succeeds lt OK gt IP Domain setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98
25. ON V4 112 100 Setup Succeeds lt OK gt Security OFF V4 112 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Enable Security Phone Number Response Description 18 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Answer Call Mode User can use Answer Call Voice Mode command to define the response when MU 201 is receiving an incoming call The device can answer the call automatically or hang up the call and send current location message Setup Format username Password Function Mode 0 3 Command username 0000 8 1 Note If user has enabled Security Phone Book function MU 201 will verify whether the caller s number is in the Security Phone Book If not MU 201 will not react to the incoming call SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 8 defines the Voice Mode setup 0 1 The device will answer the incoming call automatically 2 The device will hang up the call and respond its current location to caller s cell phone 3 The device will hang up the call and respond its current location to the defined route End sign Table Answer Call Mode Setup Format Description
26. Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 9 defines the Default Setting setup mode End sign Table Default Setting Setup Format Description Situation Message Reply Setup Succeeds lt OK gt Reset to default V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Default Setting Setup Response Description 56 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Tail Report The Tail Report function helps user get more information about tracker and environment status The additional information includes RSSI vibration sensor status report number charging status and the nearest GSM base transceiver station Cell ID information Command fic tailon A standard GPRMC sentence for MU 201 is shown as the following imei 357566000009752 amp rmc GPRMC 073900 00 A 2457 81167 N 12125 53948 E 0 009 180811 A 7E AUTO V3 793 56 A GPRMC sentence with Tail Report is shown as the following imei 357566000009752 amp rmc GPRMC 073900 00 A 2457 81167 N 12125 53948 E 0 009 180811 A 7E AUTO V3 793 56 R27 M1 16745 C1 MCC466 MNC97 LAC51145 CID16012 SMS COTA Command Description Start sign Mode fic defines Tail Report mode tailon tailo
27. V3 793 56 Setup Succeeds PR St ues No 36 Zhongshan Rd Tucheng District New Taipei City Taiwan 236 Actual address Table Polling Setup Response Description 29 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Google MAP Report with Address Use this command to define the SMS report format when route is set at 4 SMS or Answer Call Mode is set at 2 or 3 There are 2 modes 1 GPRMC Format and 2 SMS Google Map Format With SMS Google Map Format the device will send the device location in Google Map hyper link It can be shown on the mobile browser which supports Google Map display GPRS 3G required User also can use this command to have the device send location address information which corresponds to the nearest position of the device The Google Map hyper link and address information can be set both available or individually There will be 2 separate messages sent to the caller s cell phone if both Google Map hyper link and address are enabled one is Google Map hyper link sentence and the other is address sentence Setup Format username Password Function Mode on off Command username 0000 google 3 Google Map hyper link sentence example http maps google com maps q 24 963544 121 425648 tracker amp AUTO V3 793 56 Original GPRMC Format sentence example username GPRMC 052720 00 A 2457 48758 N 12125
28. acker User Manual Change User Name Generally SMS command execution needs correct user name with password or it will remain the same setting The SMS command default user name is username It can be changed by following the command format For example entering the SMS command as the following allows user to change the user name from username to a new user name jacky Only enter new command with new user name after it has been changed Setup Format username Password Function Mode New User Name Command username 0000 1 jacky SMS COTA Command Description Start sign user name Default ID of the device 0000 Default password If you have changed the password please use the updated one Mode 1 defines user name setup mode New user name changed by the user At the maximum of 16 characters including a z A Z 0 9 1 8 amp Please notice that you should notice if the letters is capitalized or in small letters when sending the command End sign Table User Name Change Format Description Situation Message Reply Setup Succeeds lt OK gt Username setup V4 231 100 Setup Fail lt FAIL gt Username setup V4 231 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 200 100 Table User Name Change Response Description 8 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracke
29. an Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Route for Data Transmission This SMS command instructs the device decide to transmit GPS GPRMC positioning data to where in which protocol Please confirm the back end server protocol type and corresponded URL or IP address with port number if required before setup There are 4 main protocols available for transmitting route setup 1 HTTP Hypertext Transfer Protocol An internet browser based server protocol that usually has a specified URL Uniform Resource Locator 2 TCP IP Transmission Control Protocol An OSI Transport layer protocol that has more complex frame structure higher reliability but slower processing speed than UDP IP 3 UDP IP User Datagram Protocol An OSI Transport layer protocol that has faster processing than TCP IP but does not guarantee data delivery 4 SMS The DEVICE will send GPS data by SMS message format to Cellular phone User can choose the route to transmit the data by HTTP TCP UDP protocol individually or with SMS message as a backup route Please refer to the following table for the route setup Setup Format username Password Function Mode 0 2 4 6 7 8 or 9 Command username 0000 14 6 SMS COTA Command Description Start sign Default ID of the device If you have changed the user name please use the updated one Default password If you have changed t
30. assword please use the updated one Mode vs defines Vibration setup mode Enable the vibration Disable the vibration Enable Vibration Status events report Disable Vibration Status events report End sign Table Vibration Event Setup Format Description Situation Message Reply Setup Succeeds lt OK gt VS ON VS SHOW V3 937 76 Emergency Mode lt FAIL gt PANIC ON Command not Allow V3 937 76 Table Vibration Event Setup Response Description 38 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Vibration Sensitivity User can define the sensitivity of Vibration by setting the following SMS COTA command There are 3 steps to define the sensitivity from most sensitive to least sensitive Setup Format username Password Function Mode on off show hide write Sensitivity Stop Detection Buffer Time Command username 0000 vs on show write 1 180 SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode vs defines Vibration setup mode Enable the vibration Disable the vibration Enable Vibration Status events report Disable Vibration Status events report
31. can exit SOS Mode by long pressing the SOS button again Please refer to Hardware General Introduction SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode offpanic defines the SOS Exit mode End sign Table Exit from SOS Mode Setup Description Situation Message Reply Setup Succeeds lt OK gt Panic OFF to normal mode V3 793 56 Table Exit from SOS Mode Response Description 23 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Auto Report Generally the device will generate GPS GPRMC data and report to server specified cellular phone or network routes Auto Report setup can enable the device report GPS data automatically during a period of time Use this command to set up the frequency of Auto Report The device can report according to time interval If you send the SMS command as the following example the device will send a report every 5 minutes 300 seconds and the total number of reports is 99 Setup Format User Name Password Function Mode Intervals sec Total number of reports Time Unit s m h Example1 username 0000 6 300 99 Example2 username 0000 6 300 99 s Note The report times of Auto Repo
32. ce coordinates and function setting all 10 sets End sign Table All Geo Fence Coordinate Enable Format Description Situation Message Reply lt OK gt GF ON V3 793 56 lt OK gt GF OFF V3 793 56 Setup Succeeds lt OK gt 160 T3 M0 G1 3 G2 0 G3 0 G4 0 G5 0 G6 0 G7 0 G8 0 G9 0 G10 0 V3 7 93 56 lt OK gt GF CLEAR V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table All Geo Fence Coordinate Enable Response Description 45 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Geo Fence Event Report Interval User can use this command to define the Geo Fence Report interval period and times frequency The command is applied to all the 10 Geo Fence coordinate sets Setup Format username Password Function Mode Intervals sec Total number of reports Command username 0000 17 60 3 SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 17 defines the Geo Fence Report Interval setup mode Time Interval period of Event Report Ranges from 0 to 65000 Situation Times frequency of Event Reports that will be sent automatically Table Geo Fence Interval S
33. d to define the report in another language Setup Format username Password Function Mode Report Format Code Command hl zh tw Note Some language codes might be not available the actual supported codes relies on map service provider SMS COTA Command Description Start sign Mode hl defines the SMS Polling Address setup mode The language code such as en us zh tw ar ae etc End sign Table Address Setup Format Description Situation Message Reply Setup Succeeds lt OK gt google hl zh tw V4 133 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 133 100 Table Address Setup Response Description 32 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Language Codes Reference Table Code Country Region Code Country Region af Afrikaans Sq Albanian ar sa Arabic Saudi Arabia ar iq Arabic Iraq ar eg Arabic Egypt ar ly Arabic Libya ar dz Arabic Algeria ar ma Arabic Morocco ar tn Arabic Tunisia ar om Arabic Oman ar ye Arabic Yemen ar sy Arabic Syria ar jo Arabic Jordan ar Ib Arabic Lebanon ar kw Arabic Kuwait ar ae Arabic U A E ar bh Arabic Bahrain ar qa Arabic Qatar eu Basque bg Bulgarian be Belarusian ca Catalan zh tw Chinese Taiwan zh cn
34. device If you have changed the user name please use the updated one 0000 Default password If you have changed the password please use the updated one speed Mode speed defines the Overspeed activation setup mode on on Enable Speed Detection off Disable Speed Detection End sign Table Over Speed Setup Format Description Situation Message Reply lt OK gt Speed detect is ON V4 188 100 Setup Succeeds lt OK gt Speed detect is OFF V4 152 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Over Speed Setup Response Description 40 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Over Speed Interval Use this command to set up the Over Speed threshold and interval Once the Over Speed detection is enabled the device will start to report according speed limit interval and times MU 201 provides Over Speed Detection User can also set up detection time for misreporting Setup Format username Password Function Mode Speed Limit Unit Interval Sec Total number of reports Detection Times Command username 0000 11 100 km 10 3 5 Note1 With the above setting the device will send Over Speed Alarm at every 10 15 second it will be more than 10 since there is some delay in detection when it goes over 100km hr Note2 This is for conditions setting
35. efines Vibration setup mode Enable the vibration Disable the vibration End sign Table Vibration Setup Format Description Situation Message Reply Setup Succeeds lt OK gt VS ON V3 937 76 Emergency Mode lt FAIL gt PANIC ON Command not Allow V3 937 76 Table Vibration Setup Response Description 37 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Show Vibration Status User can set Vibration Status function to SHOW or HIDE Vibration Status event when triggering the detection When the Vibration Status function is set to SHOW the general Vibration Status events are shown as the following The device is moved imei 357248014534899 amp rmc GPRMC 032459 00 V 2457 81052 N 12125 53545 E 0 073 200411 A 61 MOVE V3 793 56 The device is stopped imei 357248014534899 amp rmc GPRMC 032459 00 V 2457 81052 N 12125 53545 E 0 073 200411 A 61 STOP V3 793 56 When the Vibration Status function is set to HIDE when the detection is triggered the Vibration Status events shown above will NOT be displayed Setup Format username Password Function Mode on off show hide Command username 0000 vs on show SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the p
36. en both time interval and distance traveled are matched If you send the SMS command as the following example the device will check the distance traveled every 5 minutes 300 seconds with previous GPS data the device will send Auto Report if the distance exceeds 100m from last known position or it will not send report if the distance does not exceed 100m it will check the distance again at the next 5 minute time interval The total number of reports times is 99 Setup Format User Name Password Function Mode Intervals sec Total number of reports Distance Interval m Time Unit s m h Command username 0000 6 300 99 100 NOTE When the Distance interval or Stationary Detection is set the tracker status event will be AGF instead of AUTO SMS COTA Command Description Start sign username Default user name of the device If you have changed the username please use the updated one Default password If you have changed the password please use the updated one Mode 6 defines Auto Report setup mode Time Interval period of Auto Report Distance Interval when the auto report function is activated the tracker will take the current position as the start If this value is defined when the tracker exceeds the distance traveled during a time of period the event report will be sent to the assigned route The unit of this function is meter The minimum distance s
37. ence Table 33 Set p Park MOVE SNOEN nues 35 Set up Move TE NN 36 Set p le d EE 37 Show Vibration EIERE 38 VENN 39 Set up Over c e HR 40 Setup Over Speed Interval 2 ENEE deg E Re sergeant eerie ated 41 Set up Geo Fence Coordinates rnauunnnnnnrnnnnnnnnnnnrnennnnnnenennnnnunnnnennenun 42 Enable Geo PeMnCe uvenner wanes disons tte 44 Set up Geo Fence Event Report Interval ss 46 d Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Setup Backup Log Interval Mode Pre defined Backup Times 47 Erase the Logged Data sr r 49 Eu BIN get ege 50 Power Cord AUTO ON EE 51 Power ON OFF Schedule NEE 53 Request Battery Voltage ege ee e EE d Edel eeneg 54 Voltage Percentage EE 55 Reset to Default Setting EE 56 Tall REDON ET 57 Appendix 1 Tracker Event EE 59 Appendix 2 GPRMC Data Output Format ss 60 Appendix 3 NMEA 0183 GPRMC Data Format 63 oem UO 64 Warranty Regulation EE 65 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual MU 201 Hardware General Introduction Specification GSM Quad Band 850 900 1800 1900MHz Compliant to GSM phase 2 2 Frequency Class 4 2W 850 900MHz Class 1 1W 1800 1900MHz GPRS multi slot class 10 GPRS GPRS mobile station class B Max Out RF power 33 0dBm 2dBm 15 102 dBm Receiving Sensitivi
38. etting is 100m s fime Unit as s for seconds default m for minutes and h for hours Table Auto Report by Distance Setup Format Description Situation Message Reply Setup Succeeds lt OK gt AGF setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Auto Report by Distance Setup Response Description 25 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Auto Report by Stationary Times The GPS GPRMC data can report to server or cellular phone automatically during a period of time or during a distance of travel or by stationary vehicle stop park status times Use this command to set up the stationary detection times of Auto Report the device will report 2 types of Auto Reports Distance Auto Reports and Stationary Auto Reports If you send the SMS command as the following example the device will check the distance traveled every 5 minutes when vehicle is moving and check the stationary status every 5 minutes 300 seconds when vehicle is stopped The device will send Auto Report if the device detected continuously 10 times stationary status so the actual Auto Report interval will be 5 minutes x 10 50 minutes it means the device will send stationary Auto Report every 50 minutes The device will not send report if the device detected stationary status fewer than 10 times or non continuity 10 times stationary
39. etup Format Description Message Reply Setup Succeeds lt OK gt GF report setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 46 Table Geo Fence I nterval Setup Response Description Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Backup Log Mode The device reports GPRMC data to the server cell phone normally via GSM GPRS mobile network When the GSM GPRS is not in service or the GSM GPRS signal is poor the GPRMC data will not be able to report to the server User can use this command to define the historical GPRMC data will be ignored directly or saved to flash memory and send to the server when GSM GPRS service is recovered Setup format username Password Function mode Backup Mode Command username 0000 21 1 Text Keyed In SMS COTA Description Start sign Username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 21 defines the historical data Backup mode 0 Disable Backup or Log function completely 1 Enable Backup function the device will log the data when there is no GSM GPRS reception End sign Table Backup Mode Setup Format Description Situation Message Reply lt OK gt LOG mode is d
40. ff To enable disable Tail Report End sign Table Tail Report Setup Format Description Situation Message Reply lt OK gt FIC TAILON V3 793 56 Setup Succeeds R27 M1 16745 C1 MCC466 MNC97 LAC51145 CID16012 lt OK gt FIC TAILOFF V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V3 793 56 Table Tail Report Setup Response Description 57 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Note A GSM Cell ID CID is a generally unique number used to identify each base transceiver station BTS or sector of a BTS within a Location area code LAC if not within a GSM network Please refer to the following description for details in each item Tail Report Item Description R27 RSSI The Received Signal Strength Indication of GSM network Ranges from RO to R31 R99 means service unavailable M1 Vibration Status Move Stop State M Vibration Sensor OFF VS Off MO Vibration Sensor ON stop state device not vibrating M1 Vibration Sensor ON move state device vibrating 16745 This is a unique code for each report This number will be accumulated and can t be set zero C1 Charging Status CO Device is not being charged C1 Device is charging MCC466 Mobile Country Code MCC is defined in ITU T E 212 for use in identifying mobile stations in GSM networks of which country
41. harging MU 201 MINI USB 8 PIN Plug power cord into Mini USB socket for charging 5V DC Input Charge the device for 2 3 hours for 1 time charging 5 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Dimension o 3 3 GSANAV 35 mm 19mm Weight 65g Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Command Setup for MU 201 MU 201 currently provides SMS command and COTA TCP command for remote setup User can setup the MU 201 by following the instructions shown in following chapters via SMS COTA Key the specific SMS message in your cellular phone and send it to the SIM number of MU 201 The setup messages are showed in the following sections 1 The default setting Default ID is username Please read chapter Change User Name to desired ID Default password is 0000 Please read chapter Change Password to change the password There is no number in the default contact Please read chapter Set up Phone Book List to add the number Default setting of Auto Report is deactivated Please read chapter Set up Auto Report by Time to setup the regular auto report Default setting of APN is only suitable for Taiwan GSM network Please read chapter Set up APN for GPRS Service to change the APN Default setting of URL is http www sanavtw com uploadM1 php Please read chapter Set
42. he event BATTERY BATTERY LOW LOW TO SHUTDOWN 59 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Appendix 2 GPRMC Data Output Format GPRMC Data Output Format HTTP TCP IP or UDP IP 1 Upload the data when GPS is fixed When execute the Auto Report according to the settings with a GPS fixed MU 201 will upload the data to HTTP or TCP or UDP The data format will be like the following Format IMEI IMEI Number amp rmc GPRMC lt UTC Time gt lt FixStatus gt lt Latitude gt lt Longitude gt lt Speed gt lt Direction gt lt Date gt lt Checksum gt lt Tracker Event gt lt Battery Voltage gt lt Battery Voltage gt Example IMEI 135790246811220 amp rmc GPRMC 031516 00 A 2457 81067 N 12125 53896 E 0 216 274 31 140211 A 67 AU TO 3 793 56 IMEI 135790246811220 amp rmc GPRMC 032903 00 A 2457 81147 N 12125 53901 E 0 018 140211 A 71 POLL 3 79 3 56 IMEI 135790246811220 amp rmc GPRMC 032210 00 A 2457 81085 N 12125 53833 E 0 359 201 82 140211 A 66 AG F 3 793 56 IMEI 135790246811220 amp rmc GPRMC 033334 00 A 2457 81122 N 12125 53836 E 0 341 10 26 140211 A 5C MOV E 3 793 56 IMEI 135790246811220 amp rmc GPRMC 033624 00 A 2457 81222 N 12125 53939 E 0 039 140211 A 72 PARK is ON now 3 793 56 IMEI 135790246811220 amp rmc GPRMC 033725 00 A 2457 81143 N 12125 53902 E 0 183 140211 A 7E PARK is OFF now 3 793 56 IMEI 135790246811220
43. he password please use the updated one Mode 14 defines Transmission Route mode HTTP SMS Send data to HTTP server If the route is not available send data by SMS message instead 2 HTTP only Send data to HTTP server No SMS backup route 4 SMS only Send data by SMS message to cell phone No backup route TCP SMS Send data to TCP server If the route is not available send data by SMS message instead UDP SMS Send data to UDP server If the route is not available send data by SMS message instead 9 UDP Only Send data to UDP server No SMS backup route End sign Table Transmission Route Setup Format Description 12 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Situation Message Reply lt OK gt Route is HTTP SMS mode V3 793 56 lt OK gt Route is HTTP mode V3 793 56 lt OK gt Route is SMS mode V3 793 56 Setup Succeeds lt OK gt Route is TCP SMS mode V3 793 56 lt OK gt Route is TCP mode V3 793 56 lt OK gt Route is UDP SMS mode V3 793 56 lt OK gt Route is UDP mode V3 793 56 lt FAIL gt PANIC ON Command not Allow V4 091 98 lt FAIL gt PANIC ON Command not Allow V4 091 98 lt FAIL gt PANIC ON Command not Allow V4 091 98 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 lt FAIL gt PANIC ON Command not Allow V4 091 98 lt FAIL gt PAN
44. hout notice b Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV Document Amendments MU 201 GPS GPRS Nano Tracker User Manual Revision Date F W Version Comments 1 0 1 2011 1 5 B2 02T Main Functions implemented 1 0 2 2011 3 8 B2 02T LED amp SMS commands Redefined 1 0 3 2011 4 20 B2 03T Bug fixes VS status show hide HTTP get post protocol 1 0 4 2011 5 25 B2 05T Specifications amp VS status show hide 1 0 5 2011 7 29 V2 06 Vibration sensitivity 1 0 6 2011 8 18 V2 07 1 Define over speed logic 2 Add Tail Report On Off 3 Modify all respond messages by SMS COTA 1 0 7 2011 10 5 V2 08 1 Define the battery gauge data come after voltage information 2 Px3kr connection support 1 0 8 2011 11 10 V2 09 Vibration Sensor logic 1 0 9 2011 12 7 V3 00 Quick reset 1 1 0 2011 12 27 V3 01 1 Heartbeat 2 During startup GPS and GSM LED will stay ON Red light for 20 seconds 1 1 1 2011 12 29 V3 02 Add GF clear data function 1 1 2 2012 3 21 V3 03 1 PIN Code 2 Show LP when under 3 7V LP 3 MCU shutdown voltage is from 3 4V to 3 15V 4 Power button 5 AUTO ON 6 Power OFF Message 7 Power ON OFF schedule 8 Use replace with for GF and voltage message 1 1 3 2012 4 10 V3 031 Bug fix for PIN code setup fail 1 1 4 2012 7 2 V3 06 Log GPRMC sentences increased from 2000 to 5000 1 1 5 2012 7 16 V3 06 New amendment amp release 1 Voltage Percentage P53 1 1 6 2012 8
45. ion a unique number for identifying mobile devices validity in GSM network As above stated each device has a unique IMEI number Entering the command as the following allows user to check the IMEI number of the device for network registration and tracking Setup Format username Password Function Mode Command username 0000 imei SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode imei defines the device IMEI number request mode End sign Table I MEI Number Request Format Description Situation Message Reply Setup Succeeds lt OK gt Read IMEI 357566000046804 V4 097 98 Table I MEI Number Request Response Description 10 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up APN for GPRS Service Access Point Name APN is a protocol that typically allows a user s device to access the internet using the mobile phone network It is a network identifier used by a mobile device when connecting to a GSM carrier The carrier will then examine this identifier to determine what type of network connection should be created For uploading the data to a web server a set of GPRS APN from your GSM network is required Various GSM network p
46. isable V3 793 56 Setup Succeeds lt OK gt LOG mode is backup mode V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Backup Mode Setup Response Description 47 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Operation logic Diagram of Backup Mode 1 username 0000 21 1 The time of sending data to assigned router Check the availability of GPRS then SMS Send all the data to a URL or an IP address Back up the data 48 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Erase the Backup Data The device reports GPRMC data to the server cell phone normally via GSM GPRS mobile network When the GSM GPRS is not in service or the GSM GPRS signal strength is poor the GPRMC data will not be able to report to the server They will be saved to flash memory as backup and back to the server when GSM GPRS service is recovered User can use this command to erase the logged historical GPRMC data stored at the flash memory of the device Setup Format username Password Function Mode Command username 0000 er SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use
47. ith an AUTO message When any other event is triggered and the priority is greater than AUTO the AUTO report will be saved to flash and report to assigned route later AGF BAGF NOTE When the device AUTO report Distance interval or Stationary Detection is set the tracker status event will be AGF instead of AUTO PARK BPARK When the park function is activated the server will receive a RMC sentence This sentence is ended by PARK is ON now This indicates that the PARK detection is started When park function is deactivated the server will receive a RMC sentence which is ended by Park is OFF now MOVE BMOVE When the device exceeds the movement threshold in Park Vibration detection mode it will trigger the MOVE event according to the setting POLL BPOLL When sending polling command to poll the report it triggers the POLL event GFIN BGFIN When entering the Geo Fence restricted area it triggers the GFIN 1 10 event GOUT BGOUT When leaving the Geo Fence curfew area it triggers the GOUT 1 10 event Overspeed BOverspeed When the device exceeds the speed limit threshold it triggers the Over Speed Event SOS BSOS When the SOS Panic function is activated it triggers the SOS Event LP When the device is in 1 low power under 3 700V status it triggers the LP Event When the device is in 279 low power under 3 400V status it triggers t
48. k if SIM Card is inserted in the correct direction Check if your SIM Card supports 2G 2 5G network Some 3G SIM card is not backward compatible Please make sure there is valid GSM signal in your testing environment Can t fix GPS signal Check if GPS LED flashes every 5 seconds Blue Make sure there is valid GPS signal in your testing environment Open sky Can t receive any data on the server or cell phone Make sure you have activated GPRS feature in SIM Card Check with your GSM carrier if you have the correct APN setting Please save your complete setting and send it to SANAV for further support User can save the setting using GPS Tracker Utility Can t charge the device Check if the Blue Green LED works Flash 1s Check if you have used the correct cable for charging not the USB Data Cable Check if the LED light on the Charger is steady ON Check if the USB connection is solid between Power Cord and the AC Adapter 64 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Warranty Regulation Warranty Time Period and Repair Coverage SAN JOSE TECHNOLOGY I NC warrants MU 201 to be free from all defects and malfunctions in materials and workmanship for a period of 12 months from the original purchase date from SAN JOSE Technology or authorized dealers If the equipment functions i
49. le SMS Polling Setup Format Description Situation Message Reply username GPRMC 062032 00 A 2457 80696 N 12125 52737 E 0 344 26 82 090211 A Setup Succeeds 59 POLL V3 793 56 Setup Succeeds username http maps google com maps q 24 963528 121 425658 tracker amp POLL Google hyper link V3 793 56 Table SMS Polling Setup Response Description 28 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Polling Format The user can send the SMS COTA polling according to the shown example to get desired information It defines the report format when you set SMS polling Setup Format username Password Function Mode Report Format Code Command username 0000 10 2 SMS COTA Command Description Start sign user name Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 10 defines the SMS Polling setup mode Report Format Code Google Map Hyperlink Actual Address show the nearest address from Google database To include both Google Map Hyperlink and Actual Address End sign Table Polling Format Setup Description Situation Message Reply Setup Succeeds username http maps google com maps q 24 963528 121 425658 tracker amp POLL Google hyper link
50. mproperly during the warranty period SAN JOSE Technology will either repair or replace the unit without charge Such repair service will include necessary adjustments remanufacture and replacements The product should be returned freight prepaid by the purchaser within valid warranty period Notice that you must contact SAN J OSE Technology for a RMA Return Material Authorization number before returning the goods for repair Telephone assistance will also be provided during the warranty period Limitations This warranty is limited only to the repair or replacement of defective parts confirmed by SAN JOSE Technology to be a result of faulty materials or workmanship Instruments mechanically or physically damaged due to the following conditions are beyond our warranty Neglect misuse or abuse such as a incorrect testing installation or operation Place subject in extreme environments beyond the limits of the specifications Subjected to disassembling soldering alteration unauthorized repair and electrical shock by nature Any incidental or consequential losses or damages result from the purchase Disaster accident using any unauthentic substitutive equipment or loss of any accessory that s not provided by SAN JOSE Technology For damages caused under the above conditions we ll contact you to discuss replacement options This device complies with Part 15 of the FCC Rules Operations is subject to the following two Conditions 1
51. ng their whereabouts via the GPS The purpose of geo Fencing is to ensure a company s mobile employees travel locally or drive company vehicles as part of their job stay within the boundaries the company deems productive It is essentially another way for large corporations and businesses to monitor their employees actions at work User can set up the Geo Fence coordinates by entering SMS command below The Geo Fence coordinates gfi gf10 are defined as a circular area Therefore the coordinate is the center and the radius is defined in meter There are totally 10 groups of Geo Fence coordinates can be set and saved Setup Format username Password gfi 10 Latitude N S Longitude E W Radius GF Function Mode Command username 0000 gf1 2458 9741 N 12125 6460 E 500 1 username 0000 gf1 1 Enable Geo Fence detection if the coordinates are predefined SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode gf 1 10 defines the Geo Fence 1 10 setup mode 2458 97411 Latitude unit ddmm mmmmm N N Northern S Southern 12125 64601 Longitude unit dddmm mmmmm E E Eastern W Western 500 meters in radius Minimum recommended radius 100 meters Disable the Geo Fence Detection
52. o Russian Republic of Moldova SZ Sami Lappish sr Serbian Cyrillic sr Serbian Latin sk Slovak sl Slovenian sb Sorbian es Spanish Spain es mx Spanish Mexico es gt Spanish Guatemala es cr Spanish Costa Rica es pa Spanish Panama es do Spanish Dominican Republic es ve Spanish Venezuela es co Spanish Colombia es pe Spanish Peru es ar Spanish Argentina es ec Spanish Ecuador es cl Spanish Chile es uy Spanish Uruguay es py Spanish Paraguay es bo Spanish Bolivia es sv Spanish El Salvador es hn Spanish Honduras es ni Spanish Nicaragua es pr Spanish Puerto Rico sx Sutu SV Swedish sv fi Swedish Finland th Thai ts Tsonga tn Tswana tr Turkish uk Ukrainian ur Urdu ve Venda vi Vietnamese xh Xhosa ji Yiddish zu Zulu Source link http msdn microsoft com en us library ms533052 v vs 85 aspx 34 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Park Move The user can set this command or press SOS button shortly to enable and disable the Park function When Park is enabled Auto Report will be pending until MOVE event is triggered If the device senses movement MOVE it will send MOVE reports to the assigned route by interval and times Park mode will be disabled and Auto Report will be recovered once all MOVE reports are sent Setup Format username Password Functi
53. on Mode on off Command username 0000 park on SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one 0000 Default password If you have changed the password please use the updated one park Mode park defines the Park setup mode on on Activate Park function off Deactivate Park function End sign Table Park Setup Format Description Situation Message Reply lt OK gt PARK ON V3 793 56 Setup Succeeds lt OK gt PARK OFF V3 793 56 Emergency Mode in emergency Park mode cannot be activated 3 833V Table Park Setup Response Description 35 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up Move I nterval When the park function is activated user can use this command to set up MOVE report interval period and times frequency Setup Format username Password Function Mode intervals sec Total number of report Command username 0000 16 60 3 Note This is for conditions setting only please send username 0000 PARK ON to activate the function SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please
54. r User Manual Change Password Generally SMS command execution needs correct user name with password or it will remain the same setting The SMS command default password is 0000 It can be changed by following the command format For example entering the SMS command as the following allows user to change the password from 0000 to a new password 1111 Only enter new command with new password after it has been changed Setup Format username Password Function Mode new Password new Password Command username 0000 2 1111 1111 SMS COTA Command Description Start sign username Default ID of the device If you have changed the username please use the updated one Default password If you have changed the password please use the updated one Mode 2 defines the password setup mode New password Please note at the maximum of 4 number 1111 Reconfirm the password Table Password Change Format Description Situation Message Reply Setup Succeeds lt OK gt Password setup V4 239 100 Setup Fail lt FAIL gt Password setup V4 239 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 200 100 Table Password Change Response Description 9 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Request I MEI Number IMEI stands for International Mobile Equipment Identificat
55. re 10 sets of Geo Fence can be predefined 0 It will disable the Geo Fence detection 1 It will trigger the event when the tracker is outside of the Geo Fence 2 It will trigger the event when the tracker is inside of the Geo Fence 3 It will trigger the event when the tracker is either outside or inside of the Geo Fence Table Geo Fence Coordinate Enable Format Description Situation Message Reply Setup Succeeds lt OK gt GF ONgf1 SETUP V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Geo Fence Coordinate Enable Response Description 44 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual If the user likes to enable all the 10 sets of Geo Fence coordinates at once it can be done by entering the following SMS COTA command Setup Format username Password Function Mode Command username 0000 gf on SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password gt gt If you have changed the password please use the updated one Mode gf defines the Geo Fence setup mode on To enable Geo Fence function all 10 sets off To disable Geo Fence function all 10 sets read To read Geo Fence GF function code all 10 sets clear To clear Geo Fen
56. rity Phone Book setup mode The ID of each phone number User can put 1 10 here 886123456789 The Security Phone number you would like to assign to the ID End sign Table Security Phone Number Setup Format Description Situation Message Reply Setup Succeeds lt OK gt Sec phone 1 0916004972 V4 112 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Security Phone Number Setup Response Description 17 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Enable Security Phone Book User can use this command to enable disable Security Numbers Functions Setup Format username Password Function Mode on off Command username 0000 security on Note The numbers preset in SOS Phone and Phone Book are also considered as Security Phone number once this function is enabled SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode security defines the enable Security Phone Number mode Only accept calls commands by security number Accept all the calls commands End sign Table Enable Security Phone Number Format Description Situation Message Reply lt OK gt Security
57. rname GPRMC 033624 00 V 2457 81222 N 12125 53939 E 0 039 140211 A 72 PARK is ON now 3 793 56 username GPRMC 033725 00 V 2457 81143 N 12125 53902 E 0 183 140211 A 7E PARK is OFF now 3 793 56 username GPRMC 034429 00 V 2457 81213 N 12125 53903 E 0 189 140211 A 7B SOS 3 793 56 username GPRMC 165724 00 V 2459 57367 N 12126 02097 E 0 671 182 53 180211 A 6B AUTO 3 793 56 LP username GPRMC 172827 00 V 2459 56287 N 12126 03198 E 0 733 342 42 180211 A 69 3 793 56 LP Device BATTERY LOW username GPRMC 030930 00 V 2457 81198 N 12125 53663 E 0 161 210211 A 73 GFIN 1 3 793 56 username GPRMC 105735 00 V 2459 34799 N 12125 92549 E 5 747 34 34 180211 A 5D GOUT 2 3 793 56 62 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV Appendix 3 NMEA 0183 GPRMC Data Format MU 201 GPS GPRS Nano Tracker User Manual RMC Recommended Minimum data The Recommended Minimum data format is defined by NMEA National Marine Electronics Association for GPS system data transmission Format GPRMC Time A V Latitude South North Longitude East West Ground Speed Direction Date A CS lt CR gt lt LF gt Example GPRMC 110214 00 A 2457 81039 N 12125 54004 E 0 634 287 73 210111 A 62 Name Format Example Unit Description GPRMC string GPRMC RMC protocol header Time hhmmss ss 110214 00 UTC Time Time of position fix in hours minutes
58. rovides different GPRS APN settings Please ask your GMS carrier about the APN settings If the user name and password of APN are indefinite or showed in blank just leave the parameters empty no space User can follow the Setup Format below to setup the APN that is provided by your GSM carrier Setup Format username Password Function Mode APN name APN username APN password APN DNS Example1 username 0000 3 twm 1234 1234 172 20 2 10 Example2 username 0000 3 internet Note1 The total length of APN name APN username APN Password and APN DNS should be less than 70 characteristics Note2 Some PREPAID PHONE CARD SIM modules do not enable or even support GPRS service Please consult with GSM carrier for further information SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 3 defines the APN setup mode twm APN Name 1234 APN user name optional 1234 APN Password optional 172 20 2 10 APN DNS optional End sign Table APN Setup Format Description Situation Message Reply Setup Succeeds lt OK gt GPRS APN setup V4 195 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table APN Setup Response Description 11 Copyright 2011 S
59. rt I nterval Setup Response Description 21 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual SOS Event Report Flow Long Press SOS Button Yes Check Phonebook ll No Send SOS event report to all numbers Yes Check SOS Phone Send SOS message to all numbers Call hangs up No Send the rest SOS event reports to H server by interval and times SOS Event Report Flow Description 1 SOS mode Long press power button to more than 3s the SOS function will be triggered with beep sound 2 Send 1 SOS event alarm report to all number in the phone book if the phone book number is set Please refer to Set up Phone Book List 3 Calls SOS phone number if this number is set in the SOS phone book Please refer to Set up SOS Phone Book 3 1 User can finish the call anytime without limitation 3 2 Send the rest SOS event reports to the server by report interval and times after the call is finished 4 For SOS event report interval and times setup please refer to Set up SOS Event Report I nterval 22 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Stop SOS Report Exit from SOS Mode While the device is in SOS Mode user can use this SMS COTA command to stop the SOS report and Exit from SOS mode Setup Format username Password offpanic Command username 0000 offpanic Note User
60. rts can be set by entering the digits from 1 to 9998 in the total number of reports field When 9999 is entered the device will generate unlimited Auto Reports when 0 is entered the device will stop disable Auto Report SMS COTA Command Description Start sign username Default user name of the device If you have changed the username please use the updated one Default password If you have changed the password please use the updated one Mode 6 defines Auto Report setup mode Time Interval period of Auto Report Times frequency of Auto Reports that will be sent automatically Time Unit as s for seconds default m for minutes and h for hours In this example we put 300 in constant interval of sending data and blank for the Time Unit so the actual report will be 300 seconds Table Auto Report Setup Format Description Situation Message Reply Setup Succeeds lt OK gt Auto setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Auto Report Setup Response Description 24 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Auto Report by Distance The GPS GPRMC data can report to server or cellular phone automatically during a period of time or during a distance of travel Use this command to set up the distance Auto Report The device will report only wh
61. seconds UTC Navigation receiver warning status Status Capital letter A V Navigation receiver warning maybe invalid A Data valid OK User datum latitude in degrees minutes and thousandths of Latitude ddmm mmmmm 2457 81039 minutes South N North latitude Capital letter N North S South latitude User datum longitude in degrees minutes and thousandths of Longitude dddmm mmmmm 12125 54004 minutes East E East longitude Capital letter E West W West longitude Ground numeric 0 634 knot Speed over ground in nautical miles per hour Speed Direction numeric 287 73 degree Course over ground degrees true Date ddmmyy 210111 Current Date in Date Month and Year format 2r N A N A Null field Mode A Autonomous A Indicator D Differential Mandatory checksum 8 bit exclusive OR of all data in the CS hexadecimal 62 sentence including comma between but not including the and delimiters CR LF End of message 63 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV FAQ MU 201 GPS GPRS Nano Tracker User Manual Can t turn ON the device Make sure if the device is fully charged Check if the Power button is stuck Check if the Power Button is disabled Can t fix GPS signal Check if GSM LED flashes every 5 seconds Green Check if you have disable SIM Card PIN code Make sure you have inserted SIM card BEFORE turn on the device Chec
62. ssage Reply Setup Succeeds lt OK gt SOS phone 0935304180 V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 20 Table SOS Phone Book Setup Response Description Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Set up SOS Event Report Interval Use this SMS COTA command to predefine the SOS report interval by following the format below Setup Format username Password Function Mode SOS report interval Total number of SOS reports Command username 0000 15 30 3 Note SOS report interval ranges from 1 65000 seconds SOS report times ranges from 1 9999 times SMS COTA Command Description Start sign username Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 15 defines the SOS Report Interval setup mode It defines the report interval in this case one report per 30s when SOS is triggered It defines how many times the SOS report will be sent to the assigned route in this case 3 times End sign Table SOS Alarm Report I nterval Setup Format Description Situation Message Reply Setup Succeeds lt OK gt Panic setup V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table SOS Alarm Repo
63. stant interval and s for the Time Unit so the actual report will be 300 seconds Table Auto Report by Stationary Setup Format Description 26 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Situation Message Reply Setup Succeeds lt OK gt AGF setup V3 793 56 lt FAIL gt PANIC ON Command not Allow V4 091 98 Emergency Mode Table Auto Report by Stationary Setup Response Description 27 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Current Position Polling The user can send the SMS command according to the example shown below to have the device send GPS data right away SMS Polling It will transmit current GPS data to the USER S CELL PHONE NUMBER at once While the route is set to SMS mode it will transmit current data to your cell phone that you sent the SMS Polling command to the device Setup Format username Password Function Mode Command username 0000 10 Note For Google hyper link setting please refer to Set up SMS Google Map Report SMS COTA Command Description Start sign user name Default ID of the device If you have changed the user name please use the updated one Default password If you have changed the password please use the updated one Mode 10 defines the SMS Polling setup mode End sign Tab
64. status The total number of reports times is 99 Setup Format User Name Password Function Mode Intervals sec Total number of reports Distance Interval m stationary Detection times Time Unit s m h Command username 0000 6 300 99 100 10 s NOTE When the Distance interval or Stationary Detection is set the tracker status event will be AGF instead of AUTO SMS COTA Command Description Start sign username Default user name of the device If you have changed the username please use the updated one Default password If you have changed the password please use the updated one Mode 6 defines Auto Report setup mode Time Interval period of Auto Report Distance Interval when the auto report function is activated the tracker will take the current position as the start If this value is defined when the tracker exceeds the distance traveled during a time of period the event report will be sent to the assigned route The unit of this function is meter The minimum distance setting is 100m Stationary Detection If this value is defined by 5 the tracker will detect if the tracker exceeds the circle for 5 times If the tracker doesn t exceed this circle the tracker will send a notice command The unit is times Time Unit as s for seconds default m for minutes and h for hours In this example we put 300 in con
65. the updated one Mode er defines the Data Erase mode End sign Table Erase the Logged Data Format Description Situation Message Reply Setup Succeeds lt OK gt Logged data is erased V3 793 56 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Erase the Logged Data Response Description 49 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Power Button User can use the command to enable or disable power button function When the device is ON and power button is disabled press power button will never turn OFF the device When the device is powered OFF due to low power press power button can power ON the device when the device is charging Command powerkey off SMS COTA Command Description Start sign Mode powerkey defines the power button mode Enable the power button power ON OFF is available default Disable the power button press power button will be invalid End sign Table Power Button Setup Description Situation Message Reply Setup Succeeds lt OK gt POWERKEY OFF V4 124 100 Emergency Mode lt FAIL gt PANIC ON Command not Allow V4 091 98 Table Power Button Setup Response Description 50 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Power Cord AUTO ON User can use the command to
66. ty Class II RBER lt 2 102dBm Stability Of Frequency Greater than 2 5ppm Max Frequency Error 0 1ppm GPS GPS Chipset UBX G5010 50 Channels Receiver Type GPS Li frequency C A Code GALILEO Open Service L1 frequency Tracking amp Navigation 160 dBm Sensitivity Acquisition 160 dBm Cold Start Autonomous 145 dBm TTFF Open Sky Cold start 40 s average Warm start lt 30s Hot start 2 s User Interface General Standby Time 10 minutes reporting 50 Hours estimation 60 minutes reporting 100 Hours estimation Air Interface Pr Operating Environment Operating Temperature 0 C to 55 C Storage Temperature 20 C to 85 C This specification is subject to change without prior notice 1 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Package Contents Power Cord USB Type x 1 SISANAV AC Adapter x 1 100 240V AC 1 2A Utility CD x 1 Manual amp SW Note Connect Power Cord to AC Adapter to be a whole power charging solution Optional Accessories Utility AP Data Cable for Utility Data Transmission RS USB RK 14502070 ROHS 2 Copyright 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tracker User Manual Front View GSM LED Red SOS Park Button GPS LED Blue GSM e SOS Press and hold for 3s to mors trigger SOS Mode Exit from SOS In SOS Mode press and
67. up URL to change the URL for http server setup Before doing any setup please ensure the device is connected with the GSM network The GSM LED must light on And please note the device is not in SOS Panic mode 2 Please note that all the characters which include and comma should be HALFWI DTH form 3 Please be aware of the upper capital lower cases when entering the SMS command 4 While entering any SMS command note that NO SPACE is allowed between the characters comma and signs in the SMS 5 Any setup command must be started with a sign and ended up with a sign 6 The comma can be abbreviated if no further setup required for the command besides Set up APN for GPRS Service Please refer to the examples of Set up Auto Report 6 Add or not add the sign in front of the cellular phone number s are both acceptable while the sign should precede the international call prefixes The specified international call prefix is required if sign is not added 7 The device will update setting Only when the password username and setup command are all correct If the command is not valid a failure report is going to be sent to the user s cell phone 8 Some PREPAID PHONE CARD SIM modules do not enable or even support GPRS service Please consult with GSM carrier for further information 7 Copyright O 2011 San Jose Technology Inc All Rights Reserved GSANAV MU 201 GPS GPRS Nano Tr

SANAV MU-201 GPS/GPRS Nano Tracker User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents