SANTOS :
Contents
1. the basket assembly 5 the cover 2 or the fruit plunger 3 It is recommended that all these parts of the machine are cleaned immediately after the work is finished Le QS santos FAULT FINDING First identify exactly why the machine stopped The machine will not start e Check the mains power supply and the condition of the power supply cord e Check the position of the juice bowl on the motor unit the position of the cover on the juice bowl and the locking of the clamping handle on the cover The machine stops because the motor has overheated the metal casing around the motor unit is hot Put the On Off button 11 to the 0 position then remove the plug from the power supply socket and follow the instructions in the section on motor overheating safety feature The machine stops because of an overload see the section on motor overload safety feature The machine vibrates when running empty This vibration is caused by an imbalance This imbalance may be caused by e The basket being positioned incorrectly check it is correctly positioned e Damage to the shape of the basket or its plastic base check and replace where appropriate SANTOS j REFERENCE TO STANDARDS The juice extractor No 50 complies with the following European standards CE Europe checked by the LNE National Test Laboratory GS Germany checked by the LNE National Test Laboratory UL USA and cUL2. 01 03 2010 SIGNATORY S TITLE CHIEF EXECUTIVE OFFICER SIGNATORY S NAME Aurelien FOUQUET SIGNATURE A IMPORTANT SAFEGUARDS When using cleaning or maintaining the machine always follow these instructions Read all instructions Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual INSTALLATION AND HANDLING CARE For all handling operations including unpacking the machine neither the cover clamping handle 1 nor the clamping rods 9 must not be used for holding or lifting the appliance The machine can be handled by a single person It is recommended that the appliance be placed on a table or worktop for more comfortable use so that the juice outlet spout and the On Off switch are in front of you recommended height 90 cm to be adapted as required for the user Like this the pulp container is then at the back of the machine If however the worktop is too small a position can be used with the juice outlet spout on the left and the On Off switch visible on the front Like this the pulp container is then located on the right side During cleaning and installation handle the basket assembly 5 carefully so as not to put it out of shape thus preventing the machine from working properly IMPROPER USE 1 Do not place food in the channel and press with the plunger before you have started the machine 2 The appliance is not designed for h
3. Food Outlets Special Theme Restaurants etc It has a powerful motor which drives a centrifugation basket Centrifugation basket The active filtering part of the basket is made of stainless Steel the lower part of the basket providing the drive and the locking system is made of food quality engineered plastic e 18 10 press drawn stainless steel bowl with stainless steel spout for collecting and funneling the product juices USING FOR THE FIRST TIME USING THE MACHINE FOR THE FIRST TIME Assembly and preparation 1 Fit the bowl 4 on the bowl centering device 7 making sure that the juice run off spout is located in the indent provided for this at the front of the bowl centering device Fig 4 Place the basket assembly 5 in the bowl 4 making sure it is located properly on the drive unit 17 It should go into place automatically by gravity but the position of the basket in the bowl should be checked when in place Fig 5 Fit the cover 2 on the bowl 4 making sure that when it is fitted the cover outlet is lined up with the bowl outlet Fig 6 Turn the cover clamping assembly round towards the feed channel with the clamping handle 1 raised until it is above the two notches on the side of the cover 2 Fig 7 Turn the clamping handle round 1 downwards to clamp the cover 2 Fig 8 Place the fruit plunger 3 in the cover feed channel 2 and check that the underside of the plunger collar rests against the top of t
4. Pion d entra nement 8 Entra neur Drive gt 9 Q SANTOS Fiqures Figure 6 Figure 7 Fi igure 8 Q SANTOS WARRANTY CERTIFICATE WARRANTY This appliance is guaranteed for twelve months from the date of manufacture appearing on the identification plate The guarantee is strictly limited to the free replacement of any original part acknowledged by us as being defective as a result of a fault or a manufacturing defect and identified as belonging to the appliance in question lt does nor apply to damage resulting from an installation or use which does not comply with the instructions supplied with each appliance user manual or in the event of an obvious lack of maintenance or non observance of basic electrical safety rules All part replacements under warranty are made after return of the defective part to our workshops carriage paid accompanied by a copy of this warranty certificate on which the serial number of the appliance is shown All appliances have an identification plate bearing a serial number identical to that on this warranty certificate In the event of serious damage which is deemed only to be repairable in our workshops and after agreement from our services all appliances under warranty are to be dispatched by the client carriage paid If the appliance is repaired outside the warranty the forwarding and return transport is the responsibility of the client Parts and labour are invoice
5. the 0 position Wait for the motor to cool 15 to 30 minutes then push the On Off switch 11 position 1 If the problem persists switch off the power supply to the machine unplug the cord from the mains socket 10 and call in the maintenance service or contact a SANTOS approved dealer TOOL ACCESS SAFETY FEATURE The juice extractor can only be started if the cover and bowl are positioned correctly on the motor unit 7 and the clamping handle is in the closed and locked position Releasing the cover 2 clamping handle 1 results in the machine stopping and the immobilization of the rotating elements in less than 3 seconds Re starting the juice extractor requires specific operation of the On Off switch 11 again position 1 A cut in the mains power supply results in the On Off switch 11 stopping position 0 MAINTENANCE Before carrying out any work on the juice extractor the machine must in all cases be unplugged from the mains power supply and the motor start capacitor discharged A Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor 13 The appearance of an electric arc shows that the capacitor has discharged Discharqing the capacitor Spare Parts IMPORTANT Use of spare parts other than certified original SANTOS parts is prohibited This machine requires no particular maintenance because the bearings are lubricated for life Work may however be require
6. the fruits and vegetables to prepare the juice required or change production from one juice to another but without having to remove and clean the elements of the machine Simply 1 place a new recipient under the bowl spout 2 carry out a quick automatic basket clean While the basket is turning introduce water into the cover channel This cleaning can only be contemplated in exceptional cases of small quantities of different juices for individual glass use SAFETY MAINTENANCE COVER AND BOWL PRESENCE SAFETY DEVICE For the juice extractor to be able to start the cover 2 and the bowl 4 must be centered in position on the bowl centering device 7 and held by the clamping handle 1 Putting the clamping handle in the vertical position up without the bowl or without the cover means that the machine cannot be started MOTOR OVERLOAD SAFETY FEATURE Should the motor become blocked foreign body object that is too hard too much pressure with the fruit plunger on the products being processed the On Off switch 11 automatically trips to the 0 position Correct the problem and press the On Off switch 11 position 1 If the problem persists switch off the power supply to the machine unplug the cord from the mains socket 10 and call in the maintenance service or contact a SANTOS approved dealer MOTOR OVERHEATING SAFETY FEATURE If the motor overheats the On Off switch 11 automatically trips to
7. CAUMONS e Po O II 7 HOW TO STOP THE MACHINE uronnunnonnonnnnnennnnnennnnnnnnnnnennnnsnnnnnsnnnnnennnnsnnnnnsnnnnnsnnnnnsnnnnn 8 CHANGING PRODUCTS DURING JUICE PRODUCTION AND CLEANING IN PLACE PP PA 8 SAFETY MAINTENANCE oocococcccnccononocononocononncnnnnncnnnnncnnonnnnnnncnnnnnnnnnnnnnnnnnnnnnnnnnonnncnonancnnss 9 COVER AND BOWL PRESENCE SAFETY DEVICE 9 MOTOR OVERLOAD SAFETY FEATURE ccooiccoococoonccoconoconononononoconononananno nono ccnanenneos 9 MOTOR OVERHEATING SAFETY FEATURES 9 TOOL ACCESS SAFETY FEATURE acsearle cs acer EARE E 9 PAINE NIN Eh 9 Discharging N capaci ES en en en ac danse nn eee on eee ee 10 CPR atacara 10 FAULT FINDING 0 re erere re rere nar eeseeueessaeessaueessaeeeseeeeseeeessaeeesaaes 11 THE machine WII NO SA a ee en is 11 The machine stops because of an overload occcoocncoccnconcnconcnconcnccncncnncnonncnonnnnconenennnos 11 The machine vibrates when running empty 11 REPERENGE TO STANDARD isis 12 TECHNICAE SPECIFICANONS A oars A ociacioas ici 12 Electrical wiring diagram 110 120V 50 60HZ rrrnnennnnennnnennnnennnnennnnennnnennnnernnnennnnennnnen 13 Electrical wiring diagram 220 240V 50 60HZ errar 14 TRANSLATION CHART FOR ELECTRICAL COMPONENTS cccceeceeeeeeeeeeees 15 TRANSLATION CHART FOR WIRE COLORS nissan a 15 TRANSLATION CHART FOR THE MACHINE ELEMENTS 15 A aaa ie EEE EEE EE EEEE EEEE EEE EEEE E EE A AEAEE 16 WARRANTY CERTIFICATE eegnen eee eae 18 APELIANCE
8. Canada NSF USA TECHNICAL SPECIFICATIONS 1 Power supply voltage V 220 240 110 120 Frequency Hz 50 60 50 60 Start capacitor uF 50 260V 250 160V Start relay SANTOS reference 90949 50545B og Power requirement A 25 3000 3600 3 secs max Noise 2 dBA Measured at 3000 rpm 65 65 LAeg dB Min 4 C Max 120 C 2 ref 20uPa Electrical wiring diagram 110 120V 50 60Hz QS Blue Red Condensateur White White sl sr Blue 2 4 3 NNN ns P 4 LS 13 d marrage Marche Arr t E E naa aa P1 o b Black Black 3 White White White Interrupteur de Freinage Black Black GREEN YELLOW 6 Masse moteur GREEN YELLOW Masse virole Le Electrical wiring diagram 220 240V 50 60Hz S Blue Red Condensateur White White _ End Blue 1 3 E NNN a 4 sa Is d marrage Marche Arr t E E 187 av pur P1 Black P2 Black J interrupteur Freinage Black LA Black GREEN YELLOW 5 Masse moteur GREEN YELLOW 6 Masse virole I lt 2 TRANSLATION CHART FOR ELECTRICAL COMPONENTS Condensateu Relais de d marrage Start relay Interrupteur freinage Switch brake Marche Arr t On Off Masse moteur Motor ground Shell ground TRANSLATION CHART FOR WIRE COLORS En gt BLANC NOIR BLEU ROUGE VERT JAUNE TRANSLATION CHART FOR THE MAGHINE ELEMENTS tem Fr fn 6 Conteneurapulpe Pulp container gt St A AAA
9. IDENTIFICATION PLATE sarro piratas 18 Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual 2 18 CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS SAS 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE HEREBY DECLARES THAT THE MACHINE DESIGNATED ON THE IDENTIFICATION PLATE AFFIXED e UNDER THE APPLIANCE e ON THE WARRANTY CERTIFICATE ON THE LAST PAGE OF THIS MANUAL COMPLIES WITH THE PROVISIONS OF THE machines DIRECTIVE n 2006 42 CE AND THE NATIONAL LEGISLATION TRANSPOSING IT IT ALSO COMPLIES WITH THE PROVISIONS OF THE FOLLOWING EUROPEAN DIRECTIVES e No 2006 95 EC Low voltage directive e No 2004 108 EC CEM directive e No 2002 95 EC ROHS directive e No 2002 96 EC WEEE directive The machine complies with the provisions of the following harmonized European standards e NF EN 1678 A1 2010 Machines for food products vegetable slicers Safety and hygiene regulations e NF EN 12547 A1 2009 Juice extractor Common safety instructions e NF EN ISO 12100 1 and 2 2004 Machine safety devices General design principles e NF EN 60204 1 2006 Machine safety devices Machine electrical equipment General regulations e NF EN 60335 1 2003 Safety of household and similar electrical appliances e EN 60335 2 64 2004 Part 2 64 Particular requirements for commercial electric kitchen machines SIGNED IN VAULX EN VELIN ON
10. SANTOS 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE TEL 33 0 472 37 35 29 FAX 33 0 478 26 58 21 TELECOPIE 33 0 478 26 58 21 E Mail santos santos fr www santos fr JUICE EXTRACTOR f 50 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE on Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Cheese graters Ice crushers Mincers Vegetable slicers Dough mixer Moulins caf Presse fruits Mixers Blenders Distributeurs de boissons Batteurs m langeurs P trin R pes fromage Broyeurs gla ons Hache viande Coupe l gumes MODELES DEPOSES FRANCE ET INTERNATIONAL INTERNATIONALLY PATENTED MODELS A CONTENTS CE COMPLIANCE D CLARATION cottaeots 3 IMPORTANT SAFEGUARDS vr 4 INSTALLATION AND HANDLING ooocccnccncnnccnnnnncncnoncnonocononnnnnononononnnnonnnnnnnnrnnnnnnnnnencnnnnos 4 MPROPER USB toto a a 4 ELECTRICAL CONNECTION a Seto a S 4 USING FOR THE TS CAMES a a SUA at eee das 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE 5 JUICE EXTRACTOR 50 and basket 6 USING FOR TRE FIRST TIMES A oicaads 6 USING THE MACHINE FOR THE FIRST TIME 6 Assembly and preparation cccccsccceeccescccseeceecceucecseeceueceeeceueesseeceeeseueeseeesseeseaeenees 6 A 7 TN 7 EN 7 FPrC
11. andling frozen foods Remove stones from fruit before processing it in the machine e g mangoes apricots peaches Do not let the stones go into the machine Neither a hose nor a pressure hose should be used for cleaning The machine must not be left to operate without supervision Do not use abrasive sponge for cleaning the basket Use of spare parts other than certified original SANTOS parts is prohibited o NS ELECTRICAL CONNECTION The juice extractor no 50 is available in two voltages for the electrical power supply e 220 240V 50 60 Hz single phase e 110 120V 50 60 Hz single phase 2 Q SANTOS Line protection the appliance should be connected to a standard 2 pole earth electric socket The installation should be fitted with an RCD and a fuse rated at 16A The appliance must be earthed CARE e Before connecting the machine check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate 16 under the machine gt or on the identification plate on the last page of this manual e l the power cable 10 is damaged it should be replaced by a special assembly available from approved SANTOS dealers or from SANTOS USING FOR THE 1st TIME Remove the plunger 3 Turn the clamping handle 1 upwards to release the cover 2 Fig 2 To be able to remove the cover turn the clamping handle and clamping rods 9 assembly
12. d at the prices in force Spare parts price hourly labour cost All repairs will be subject to a prior estimate which should be agreed before repair In the event of a dispute the Courts for the manufacturer s area Lyons alone have jurisdiction APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not supplied with the appliance Printed Faxed and Downloaded
13. d to change parts subject to wear such as the electrical components like the start capacitor and the start relay In this case refer to the list of components suitable for your machine depending on its operating voltage to be found on the warranty sheet supplied with the machine and on the rating plate underneath the machine The grater 14 and to a lesser extent the basket assembly 5 can be considered as parts subject to wear For the machine to operate properly it is recommended that a check is also made that the locking membrane 15 is in good condition in particular the absence of any signs of tearing Also check that the rubber drive sprockets are in good condition 17 in particular the absence of any signs of wrenching For all spare part orders see references in the exploded view at the end of the manual state the type the appliance serial number and the electrical specifications recorded under the appliance UPKEEP Neither a hose nor a pressure hose should be used for cleaning e After use clean the basket assembly bowl cover pulp container plunger and bowl centering device in clean water or with a dish washing detergent product designed for this purpose Then rinse and dry Do not use abrasive products or pads to clean the basket assembly e The base and the motor unit trim should be cleaned with a soft damp sponge and then dried CARE For easier cleaning do not leave food remains to dry in the bowl 4
14. he cover feed channel Position the pulp container 6 correctly relative to the cover outlet 2 the bowl 4 and the machine stand 8 Connect the supply cord plug 10 to your mains supply socket Withdraw the fruit plunger 3 from the cover feed channel 2 A 1 Start the machine by putting the On Off switch 11 to the 1 position the indicator will light up Using 2 Place the recipient under the bowl spout 4 3 Introduce the fruits or vegetables into the cover feed channel 2 and push them onto the rotating grater with the fruit plunger 3 4 Continue this operation until the juice recipient is full or the quantity of fruit and vegetables to be processed has run out Also keep an eye on the level of pulp in the pulp container 6 Stopping the machine 1 After use stop the machine a by putting the On Off switch 11 to the O position b by turning the clamping handle 1 upwards c by unplugging the mains cord plug 10 2 Turn round the cover clamping assembly 9 on the side opposite the cover feed channel 2 with the clamping handle 1 raised 3 Take the bowl 4 basket assembly 5 cover 2 and fruit plunger 3 unit to wash them in clean water Cleaning Handle the basket assembly 5 carefully so as not to put it out of shape thus preventing the machine from working properly To clean the basket assembly 5 the use of a non abrasive brush is recommended to clean the filter
15. sieve holes and the grater teeth properly Cleaning will be easier if you do not wait for the food remains to dry in the bowl basket and cover Precautions and risks During preparation the level in the pulp container 6 should be monitored to prevent the cover pulp outlet 2 from clogging Such clogging could result in an imbalance in the basket assembly 5 and thus a risk of damaging the machine The quantity of products to be processed before reaching the container 6 maximum filling varies depending on the products being processed As an indication it corresponds to approximately 10 kilograms of apples and approximately 6 kilograms of carrots If during preparation an imbalance should occur well before the pulp container is full it is sometimes appropriate to continue adding food for the imbalance to be cleared If however it should persist the machine should be stopped and the basket assembly 5 cleaned Certain products have the ability to clog or block the sieve holes in which case the basket assembly 5 will need to be cleaned more frequently A SANTOS HOW TO STOP THE MACHINE The machine can be stopped in several ways e by using the On Off switch 11 e by operating the bowl 4 cover 2 clamping handle 1 e by unplugging the mains cord plug 10 CHANGING PRODUCTS DURING JUICE PRODUCTION AND CLEANING IN PLACE You can change from carrots then to apples to prepare an apple carrot juice You can either mix
16. to the front Fig 3 Remove the cover 2 the bowl 4 and the basket assembly 5 Remove the basket assembly 5 and wash in clean water Wash all the elements in contact with food in clean water the plunger 3 the cover 2 the bowl 4 and the pulp container 6 sad ht pr RECYCLING THE PRODUCT AT THE END OF ITS SERVIGE LIFE This equipment is marked with the selective sorting symbol relating to wastes from electrical and electronic equipment It signifies that this product should be taken over by a selective collection system conforming to the Guideline 2002 96 EC WEEE part Professional Equipment so that it can be either recycled or dismantled in order to reduce any impact on the environment For more information please contact your Retailer or the SANTOS For eliminating or recycling components of equipment please contact a specialized company or contact SANTOS The electronic products not undergoing a selective sorting are potentially dangerous for the environment The damaging materials should be eliminated or recycled according to the regulations in force JUICE EXTRACTOR 50 and basket Robust and very well constructed components made of cast aluminum engineered plastic and 18 10 stainless steel plate this juice extractor is particularly suitable for extracting juice and making coulis and sauce juices from fruits or vegetables used by the professionals in Restaurants Pizzerias Snack Bars Fast
Download Pdf Manuals
Related Search