Oriel APEX2 User Manual
Contents
1. APEX2 Oriel Illumination Systems User s Manual Ore INSTRUMENTS A Newport Corporation Brand QW Newport Family of Brands ILX Lightwave New Focus Ophir Corion Richardson Gratings Spectra P hysics MAPEX2 Rev B 10 15 2014 Apex2 Illumination Systems Page 2 TABLE OF CONTENTS GENERAL INFORMATION tell tas oir dica iio dices 5 1 1 SYMBOLES AND DEFINITIONS csssicintaiciinr ista 5 2 GENERAL WARNINGS sierainten a a a e a a a E ARa 6 Ss JEEECGTRICGARLHAZARDO M M 6 tA FIRE HAZARDS ce TEUER 7 TS LAMPAHAN DUIN E a 7 INTRODUCTION usina iii 8 So zie ud BO ai cdi EE 13 o ITEMS INCLUDEDVITESS YO TEM tiit Lilia 13 3 2 LT ca OG LAN Goa eo ee TE 13 33 CHOOSINGA EOGAT IQN 5 5 3 aan contacte bicis colita labial coin 13 Cr LAMP INSTALLATION m 14 3 5 ELECTRICAL GONNEGTION spice ote stat Ste oe ate ear ta cicle 21 3 6 LAMP INTENSITY ADJUSTMENT APEX2 QTH ONLY i 23 CONTROLLING THE APEX2 FILTER WHEEL cortada idea 24 dl MANUAL CONTRO traca c 25 4 2 DIRECT APEX2 COMPUTER CONTROL 25 4 3 MONOCHROMATOR UTILITY SOFTWARE CONTROL eee 26 4 4 MONOCHROMATOR COMMAND SET ii 28 4 5 MONOCHROMATOR HAND CONTROLLER 28 4 6 TRACO BASIC CONT ROL iii sida 29 APEXZ FEA TORE Lalli 30 Sil FILTERWHEEL OVERVIEW liaison 30 SP2. Fiber Focusing Assemblies efficiently collect and focus the collimated beam of light from the APEX2 onto a fiber optic cable or liquid light guide These assemblies attach directly to the output of the APEX2 Figure 47 Fiber Focusing Assembly Apex2 Illumination Systems Page 45 8 3 FOCUSING LENS ASSEMBLIES To focus the collimated output of the APEX2 into a concentrated spot connect the Oriel model 6195 lens holder shown in Figure 48 to the APEX2 output flange Choose any 1 5 inch 38 1 mm lens from Newport s extensive selection or order one of Oriel s preconfigured Focusing Lens Assemblies Figure 48 Model 6195 Optic Holder 8 4 BEAM TURNERS The light path extends horizontally out from the APEX2 To direct the beam up down or sideways order one of Oriel s beam turning reflector holders Then choose a dichroic or full reflector to install into the holder Figure 49 Beam Turning Reflector Holder Apex2 Illumination Systems Page 46 8 5 UV SAFETY ACCESSORIES Ultraviolet UV light is Known to cause both short term and long term damage to eyes and skin The lamps used with the APEX2 do emit UV light to varying degrees Oriel offers various accessories to protect the eyes face and hands Figure 50 shows protective gloves which are available in two different sizes Figure 51 shows the popular model 49125 UV safety glasses alongside the APEX2 Figure 50 Protective Gloves Figure 51 49125 Saf
3. Do not open the APEX2 cover and attempt to work inside without first turning the instrument off and disconnecting the power cord from the AC mains Failure to follow this warning can result in severe injury or death WARNING When installing the lamp it is required to e Wear eye protection e Wear powder free gloves e Make sure the power is turned off 1 Using a philips head screwdriver remove the 4 screws holding the top cover of the housing and set aside Refer to Figure 6 Figure 5 Remove Top Cover Screws Apex2 Illumination Systems Page 15 2 Remove the top cover and set aside as shown in Figure 6 Figure 6 Remove Housing Cover 3 Loosen and remove the knurled thumb screw shown in Figure 7 Remove the lamp cable holder plate and set aside with the thumb screw Ets A Figure 7 Remove Lamp Cable Holder Apex2 Illumination Systems Page 16 4 Squeeze lamp holder wires towards each other and then pull towards the back of the power supply Refer to Figure 8 Figure 8 Remove Lamp Cable Holder 4 The power supply cable shown in Figure 9 is secured for transportation Unfasten it and let it hang to the side for now The Xenon lamp cable is shown The appearance of the QTH cable differs slightly Figure 9 Unfasten Power Supply Cable Apex2 Illumination Systems Page 17 5 Insert the lamp as shown in Figure 10 The outer edge of the elliptical reflector must fit into the groove shown in
4. A R ee RETRO ROTTO 30 959 PAIR aaa roi 31 54 ADJUSTABLE COLLIMATING EENGS learn fee i ireland 32 55 MATING FLANGE OPTIONS street else aa fado ae 33 FILTER INSTALLATION cecceccceeeeceueseeceeeeeeeeeueaeeeeueeeseuueaueeuueaeeuuueeueuuueaeeuueeausaueeaeeuauseeenas 34 UNIVERSAL FILTER WHEEL UTILITY SOFTWARE eee 36 TAY SYSTEM REQUIREMENTS lecci 36 7 2 SOFTWARE INSTALLATION PROCEDURE consti iia dia iia 37 73 USING THE FILTER WHEEL UTILITY SOFTWARE 41 Td GCGOMMAND SE Wotan atte CET 43 ACCESSORIES m LITT 44 8 1 MONOCHROMATOR MOUNTING KITS 44 9 2 FIBER FOCUSING ASSEMBLES 5x idt odis o ruben fate datae votado cov toov vei do vu eto te Rea at evt ous 44 380 PFOCUSINGLENSASSEMBLIES crac cid 45 p4 BEAM TURNER Sisi il io iii lion 45 05 UV SAFETY ACC BS SORE Sd oi lie cli calado 46 MAINTENANCE leccio 47 Sl LAMP RERLAGEMEN E ati ida iii 47 52 CIEANNG ile 47 93 LAMP CARE AND HANOLIN Ou tisdale 47 Sd EVSE REPLACGEMENTI natillas 47 SPECIFICATIONS monomeras 48 10 41 SAP VRBES Paper P 48 10 2 UNIVERSAL FILTER WHEEL UTILITY SOFTWARE eene 49 EU DECLARAFRONOECONEORMITA leo Eus OR eat evD five dusk c Un Rise 50 Apex2 Illumination Systems Page 3 12 WARRANTYAND SERVICE alal 51 12 4 CONTACTING ORIEL INSTRUMENTS cuina ia Ni 51 122 REQUEST FOR ASSISTANCE SERVICE sica 52 12 3 REPAIR etm e ee ai iaia 52 12 4 NON WAR
5. DO NOT WISH TO BECOME A PARTY TO THIS AGREEMENT AND BE BOUND BY ALL OF ITS TERMS AND CONDITIONS CLICK THE APPROPRIATE BUTTON TO CANCEL THE INSTALLATION PROCESS DO NOT INSTALL OR USE THE SOFTWARE AND RETURN THE SOFTWARE WITHIN THIRTY 30 DAYS OF RECEIPT OF THE SOFTWARE WITH ALL ACCOMPANYING WRITTEN MATFRIAI S ALONG WITH THFIR CONTAINFRS TO THE PI ACF YOU ORTAINFD E The software to which this National Instruments license applies is Universal Filter hee Utility do not accept all these License Agreements Figure 38 Accept License Agreements 6 Click Next to start installation Otherwise click Back to change the installation settings Note Clicking Save File will save a file in Rich Text File format rtf The rtf file will list the installation summary text This file will be named save as install rtf Start Installation Review the following summary before continuing Adding or Changing Universal Filter Wheel Utility Files NI VISA 5 2 Run Time Support NI Measurement amp Automation Explorer 5 3 3 NI System Configuration 5 3 3 Click the Next button to begin installation Click the Back button to change the installation settings Figure 39 Start Installation Apex2 Illumination Systems Page 39 7 During installation a status indicator will show the overall progress Selecting Cancel brings up a dialog box to verify cancellation 8 When the installation is complet
6. Illumination Systems Page 6 1 2 GENERAL WARNINGS e Read all warnings and operating instructions for this system prior to setup and use e Do not use this equipment in or near water e o prevent damage to the equipment read the instructions in the equipment manual for proper input voltage e This equipment is grounded through the grounding conductor of the power cord e Route the power cord and other cables so they are not likely to be damaged e Disconnect power before cleaning the equipment e Do not use liquid or aerosol cleaners use only a dry lint free cloth e Lock out all electrical power sources before servicing the equipment e To avoid explosion do not operate this equipment in an explosive atmosphere e Qualified service personnel should perform safety checks after any service e If this equipment is used in a manner not specified in this manual the protection provided by this equipment may be impaired e To prevent damage to equipment when replacing fuses locate and correct the problem that caused the fuse to blow before re applying power e Do not block ventilation openings e Do not position this product in such a manner that would make it difficult to disconnect the power cord e Use only the specified replacement lamp e This product should only be powered as described in the manual e Do not remove the cover for normal usage 1 3 ELECTRICAL HAZARDS Make all connections to or from the power supply with t
7. are warranted for a period of ninety 90 days from the date of shipment WARRANTY EXCLUSIONS The above warranty does not apply to Products which are a repaired modified or altered by any party other than Oriel b used in conjunction with equipment not provided or authorized by Oriel c subjected to unusual physical thermal or electrical stress improper installation misuse abuse accident or negligence in use storage transportation or handling alteration or tampering or d considered a consumable item or an item requiring repair or replacement due to normal wear and tear Apex2 Illumination Systems Page 54 DISCLAIMER OF WARRANTIES EXCLUSIVE REMEDY THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXCEPT AS EXPRESSLY PROVIDED HEREIN ORIEL MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE REGARDING THE PRODUCTS SOFTWARE OR SERVICES NEWPORT EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR THE PRODUCTS SOFTWARE OR SERVICES THE OBLIGATIONS OF ORIEL SET FORTH IN THIS SECTION SHALL BE ORIEL S SOLE LIABILITY AND BUYER S SOLE REMEDY FOR BREACH OF THE FOREGOING WARRANTY Representations and warranties made by any person including distributors dealers and representatives of Oriel Newport Corporation which are inconsistent or in conflict with the terms of this warranty shall not be binding on
8. y S5 Universal Filter Wheel Utility Program vi Ores INSTRUMENTS Universal USB Filter Wheel Utility A Newport Corporation Brand VI Filter3___ m Filter 2 Filter 7 J Filter 3 Filter 4 Filter 5 Filter 6 Filter Selection i Device ID c Copyright 2014 Newport Corpo Figure 45 Select Filter 6 To verify which filter is currently in the light path click Filter 3 Universal Filter Wheel Utility Program vi INSTRUME NTS Universal USB Filter Wheel Utility A Newport Corporation Brand v1 0 Filter Selection Filter 3 i Device ID Fitter 2 Disconnect c Copyright 2014 Newport Corporation All Rights Reserved Figure 46 Query Filter Position 7 To disconnect from communication with the filter wheel click Disconnect Apex2 Illumination Systems Page 43 7 4 COMMAND SET To ensure latency and guaranteed delivery all communications with the device uses the control pipeline defined by the USB communications protocol COMMAND SYNTAX Use Line Feed lt LF gt as the termination character for all commands The HEX value for lt LF gt is Oa or the decimal value is 10 Example Command IDN lt LF gt Response APEX2 XE 001 1 0 lt LF gt where lt LF gt is the line feed character COMMAND LIST All commands listed below automatically assumes the line feed character is used as the termination character IDN Identification query R
9. Figure 11 CAUTION Always wear powder free gloves or finger cots when handling the lamp Handle the lamp from the outside of the reflector Making contact with the lamp or reflector may cause permanent damage Apex2 Illumination Systems Page 18 6 Clamp the lamp in place by returning the lamp holder wires to their original location per Figure 12 Figure 12 Secure Lamp 7 Connect the lamp wiring to the power supply cable The Xenon lamp connectors are designed so that they cannot be connected backwards so there is no need to be concerned with lamp polarity See Figure 13 Figure 13 Connect Lamp Wiring Apex2 Illumination Systems Page 19 8 Re attach the lamp cable holder which was set aside earlier by tightening the thumb screw as shown in Figure 14 The completed lamp installation is shown in Figure 15 with Xenon on the left and QTH on the right Figure 14 Re attach Lamp Cable Holder Figure 15 Completed Lamp Installation Xenon and QTH Apex2 Illumination Systems Page 20 9 Re install the cover taking care that the cover s safety interlock lines up with its slot as shown in Figure 16 Figure 16 Safety Interlock 10 Using a philips head screwdriver re install the 4 screws to secure the top cover of the housing Do not leave out any screws Figure 17 Cover Re installed Apex2 Illumination Systems Page 21 3 5 ELECTRICAL CONNECTION Before powering up the system for the first t
10. Oriel unless reduced to writing and approved by an expressly an authorized officer of Newport 12 6 LOANER DEMO MATERIAL Persons receiving goods for demonstrations or temporary use or in any manner in which title is not transferred from Newport shall assume full responsibility for any and all damage while in their care custody and control If damage occurs unrelated to the proper and warranted use and performance of the goods recipient of the goods accepts full responsibility for restoring the goods to their original condition upon delivery and for assuming all costs and charges Confidentiality amp Proprietary Rights Reservation of Title The Newport programs and all materials furnished or produced in connection with them Related Materials contain trade secrets of Newport and are for use only in the manner expressly permitted Newport claims and reserves all rights and benefits afforded under law in the Programs provided by Newport Corporation Newport shall retain full ownership of Intellectual Property Rights in and to all development process align or assembly technologies developed and other derivative work that may be developed by Newport Customer shall not challenge or cause any third party to challenge the rights of Newport Preservation of Secrecy and Confidentiality and Restrictions to Access Customer shall protect the Newport Programs and Related Materials as trade secrets of Newport and shall devote its best effort
11. RANTYREPA sai Nod 52 12 5 WARRANIXRERA Rabac A isis 53 120 COANER DEMO MATERIAL ebete 54 LIST OF FIGURES Figure t Basic System Block Diada iii da 9 Figure 2 Dimension Dag a ad dc lia 10 FigUfe 3 xenon Lamp Specia s ae Dance EENE 11 Flgure 4 TH Lamp Speciale bna quod dest bt tet estt eti a OEE A desa calle 12 Figure 5 Remove TOP COVE Screws na aa 14 Figure 6 Remove Housing GOVSF iio eco ei aaa 15 Figure 7 Remove Lamp Cable Holder i 15 Figure 8 Remove Lamp Cable Holder ii ote eR ee 16 Figure 9 Unfasten Power Supply Cable ooccccccoconncnnccccnoconncnnnnaconnnnononcnnnononannnnnnnnnnnrnnnnnnnannnnnonnnanenns 16 PIQUE 107 MSc La Duarte 17 Figure 11 Lamp Elpse F OSINIOMING Groove iii od 17 Figure 12 Secure LaMPrirai a a E 18 Figure 13 Connect Lamp Wi alba 18 Figure 14 iRe attach Lamp Cable Holder cvs eee iia eee ee 19 Figure 15 Completed Lamp Installation Xenon and QTH iii 19 Figure 1163 Sale Intenoc sii c el ieee 20 Figure 17 Gover Tie MS reee ai run CU uUi 20 Figure T6 APEX2 Power COMNECUONM eean a ee een 22 Figure 19 Lamp Intensity Adjustment Settings iii 23 Figure 202 Filter Wheel COMME CIONS aola pi lalla iaia ila 24 Figure 2T Manda Control GContfidibdliOl1 gains esa cede devote ie cor code ca a Lelli ee el ee een 25 Figure 22 Direct Computer Control Configuration nennen nnns 25 Figure 23 Monochromator Control Conf
12. arameters in the TracQ Basic software the monochromator automatically selects the appropriate filter for any desired wavelength Refer to the TracQ Basic manual for more information Figure 27 shows the filter setup screen for a Cornerstone monochromator The MS257 setup screen is similar but uses five filters and up to two filter wheels simultaneously Filter Selection Select Filter Auto Present System Status Filter In Use Filter Label 2 Using Table Current Wavelength Wavelength Units 922 00 nanometer Automatic Filter Change Over Table From filter to filter at wavelength 1 2 355 00 3 625 00 4 1100 00 5 1580 00 6 Inf Figure 27 Filter Selection Table in TracQ Basic NOTE The parameters entered in Figure 27 are an example The actual filter changeover parameters depend on the monochromator configuration and filters being used Apex2 Illumination Systems Page 30 5 APEX2 FEATURES The APEX2 provides a number of accessories and features This makes the APEX2 product family both convenient and compact All integrated features are built in so the unit is easy to transport set up and use 5 1 FILTER WHEEL OVERVIEW The motorized filter wheel holds up to six 6 filters The MS257 monochromator was designed to work with filter wheels containing up to five 5 filters When the MS257 is used with the APEX2 the first five filters will be selectable When used alone or with other monochromators all six 6 filt
13. control into their own custom software both instruments may be controlled by the command set used by the monochromator Set up the monochromator and APEX2 as noted in Section 4 3 and Figure 23 Refer to the monochromator s user manual for information on the command set 4 5 MONOCHROMATOR HAND CONTROLLER For those who do not wish to use a computer to control the Cornerstone Series and MS257 Series monochromators Oriel offers hand controllers which plug directly into the monochromators When the APEX2 is connected to the monochromator via a filter wheel ribbon cable the hand controller can be used to select a filter Refer to the monochromator s user manual for more information Control the Monochromator and Filter Wheel with an Oriel hand controller Ribbon cable Hand Controller Connector Filter Wheel Connector APEX2 MONOCHROMATOR outlet Note that exact location of monochromator connectors varies based on model To AC power outlet Figure 26 APEX2 Configured with Hand Controller Apex2 Illumination Systems Page 29 4 6 TRACQ BASIC CONTROL In order to ensure that the light exiting the monochromator is truly monochromatic it is necessary to incorporate optical filters into the design The physics of diffraction gratings is such that higher order wavelengths need to be blocked The filters installed into the APEX2 need to be chosen to block unwanted wavelengths By setting the filter p
14. d to reduced light output overheating damage to the envelope and premature failure The lamp s reflector is coated and should not be wiped or touched at all Remove any particulates such as dust using a bulb blower FUSE REPLACEMENT The fuse compartment may be accessed from the back of the APEX 2 as shown in Figure 52 Only qualified personnel should access the fuses 100 120 1 5AT 250V m 200 240 0 8AT 250V Figure 52 Fuse Compartment Apex2 Illumination Systems Page 48 10 SPECIFICATIONS 10 1 APEX2 ILLUMINATOR 100 watt Quartz Tungsten Light Source ie watt Xenon lamp with Halogen lamp with integrated integrated reflector elector Lamp Model 6252 6338 Lamp Lifetime Average 1000 hours 500 hours 0 to 5 VDC control signal External Lamp Intensity Control None 0 VDC no lamp output 5 VDC 100 watt lamp output PIC Towle 9 2 0 4 watts 9 4 0 4 watts Iris fully open Divergence Half Angle 4 0 0 5 5 0 0 5 Spot Size measured at 28 5 mm from 33 2 mm diameter 38 2 mm diameter output flange iris fully open Holds up to six 6 filters ordered separately Uses MES 5 with MS257 vise AA AC Input and 100 to 120 VAC 50 to 60 Hz 1 5 A 250 V Time Delay Fuse 5x20 mm Fuses quantity 2 200 to 240 VAC 50 to 60 Hz 0 8 A 250 V Time Delay Fuse Apex2 Illumination Systems Page 49 5 to 40 C 41 to 104 F indoor use only Operating Environment lt 80 relative humidity non condensing
15. e click Finish Refer to Figure 40 Installation Complete The installer has finished updating your system lt Back Neto Figure 40 Finish Installation 9 A dialog box will appear to restart the computer as shown in Figure 41 This software can be used only after the computer is restarted You must restart your computer to complete this operation If you need to install hardware now shut down the computer If you choose to restart later restart your computer before running any of this software Figure 41 Restart Computer o gt Windows Media Center Windows Media Player 1 Windows Update XPS Viewer Accessories i BlackBerry Bluetooth Devices de Broadcom Lo CyberLink PowerDVD 9 5 Intel PROSet Wireless d Maintenance Je Microsoft Expression Microsoft Silverlight Modem Diagnostic Tool de National Instruments Je Netwaiting Je Startup de Tether 4 Back Search programs and files e Paint ES cil Getting Started ES Connect to a Projector Calculator all In Sticky Notes x Snipping Tool A APS Viewer j Windows Fax and Scan A Remote Desktop Connection ey Magnifier All Programs Search programs and files Figure 42 Start Menu and Desktop Changes Apex2 Illumination Systems Page 40 10 After the computer restarts the Start menu shall contain the Filter Wheel Utility software and the National Instruments NI Max icon shall a
16. e lens position Be sure to tighten the locking screw when finished Note under normal circumstances this is the only lens which should be adjusted Do not make any changes to the relay lens position as its position was optimized before shipment Figure 30 Collimating Lens Adjustment DO NOT ADJUST Figure 31 Do Not Adjust Relay Lens Apex2 Illumination Systems Page 33 5 5 MATING FLANGE OPTIONS The APEX2 is designed with a standard Oriel 1 5 inch series mating flange allowing it to be coupled to a variety of instruments and accessories Items are connected to the mating flange by tightening three set screws shown in Figure 32 Figure 32 Oriel 1 5 Inch Series Flange Apex2 Illumination Systems Page 34 6 FILTER INSTALLATION WARNING When the light source is in use the filter wheel and all other items in the optical path may become hot Ensure items are cool before handing them Ensure the shutter is closed and the lamp is off whenever working in the filter wheel compartment Remove the front plate of the filter wneel assembly by unscrewing eight 8 flat head screws using a philips screwdriver Refer to Figure 33 Set all items aside ensuring that no foreign matter can contaminate or damage the optics Do not attempt to disconnect the output optics and flange from the front plate Figure 33 Filter Wheel Cover Screws Each filter position is labeled on the wheel Remove the filter retaining
17. ent before the problem occurred 12 3 REPAIR SERVICE This section contains information regarding factory service for this product The user should not attempt any maintenance or service of the system beyond the procedures outlined in this manual This product contains no user serviceable parts other than what is noted in this manual Any problem that cannot be resolved should be referred to Oriel Instruments If the instrument needs to be returned for service a Return Material Authorization RMA number must be obtained prior to shipment to Oriel Instruments This RMA number must appear on both the shipping container and the package documents Return the product to Oriel Instruments freight prepaid clearly marked with the RMA number and it either will be repaired or replaced it at Oriel s discretion Oriel is not responsible for damage occurring in transit The Owner of the product bears all risk of loss or damage to the returned Products until delivery at Oriel s facility Oriel is not responsible for product damage once it has left the facility after repair or replacement has been completed Oriel is not obligated to accept products returned without an RMA number Any return shipment received by Oriel without an RMA number may be reshipped by Newport freight collect to the Owner of the product 12 4 NON WARRANTY REPAIR For Products returned for repair that are not covered under warranty Newport s standard repair charges shall be appl
18. er positions may be utilized The active filter position change at a rate of 1 7 seconds per filter When applying power to the APEX2 Refer to Section 4 regarding the various methods by which the filter wheel may be controlled and Section 0 for filter installation 5 2 IRIS The manually operated iris is used to control the intensity of the Xenon or Quartz Tungsten Halogen QTH lamp At its minimum the iris acts as a 0 25 inch 6 4 mm diameter aperture Light intensity ranges from 100 when fully open to 2 at its minimum diameter The iris is adjusted by turning the black ring shown in Figure 28 Turn the black ring to adjust the iris Figure 28 Iris Control Ring Apex2 Illumination Systems Page 31 5 3 SHUTTER The integrated shutter is a very convenient feature which may be used to close off the light path while the lamp is warming up Frequently restarting the lamp may shorten the lamp s life and requires warm up time If the lamp is not needed for a short amount of time the shutter can simply be closed Turning the knob clockwise opens the shutter Rotating the knob counterclockwise closes the shutter Turn the knob to open and close the shutter Figure 29 Shutter Knob Apex2 Illumination Systems Page 32 5 4 ADJUSTABLE COLLIMATING LENS The collimating lens may be adjusted to optimize light coupling Loosen the silver thumb screw shown in Figure 30 Turn the blue knob near the output flange to change th
19. eturns identification string Oriel Instruments APEX2 Illumination System XXXXX YYYYY ZZZZZ where XXXXX YYYYY and ZZZZZ are the Model Serial and Firmware numbers of the system Example Command IDN lt LF gt Response APEX2 XE 001 1 0 The response indicates that this is a product of Oriel Instruments the product name is APEX2 Illumination System the model number is APEX2 XE the Serial number is 001 and the firmware version is 1 0 FILT Queries active filter position Returns number of the current filter position or 1 for error FILT X Sets active filter position where X is the desired filter position from 1 6 Apex2 Illumination Systems Page 44 8 ACCESSORIES The following is a small list of the optional accessories available which may be used with the APEX2 For more information visit Newport s website or contact Newport s technical sales engineers They can help configure a full system from the extensive Oriel and Newport product selection 8 1 MONOCHROMATOR MOUNTING KITS Oriel offers a selection of mounting kits which provide a common baseplate and interconnection hardware used to connect the APEX2 to many of Oriel s monochromators and spectrographs Instrument Mounting Kit Model Cornerstone 130 Monochromator APEX2 CS1 KIT Cornerstone 260 Monochromator APEX2 CS2 KIT MS260i Spectrograph APEX2 CS2 KIT MS257 Monochromator APEX2 MS1 KIT MS257 Spectrograph APEX2 MS1 KIT 8 2 FIBER FOCUSING ASSEMBLIES
20. ety Spectacles Apex2 Illumination Systems Page 47 9 MAINTENANCE 9 1 9 2 9 3 9 4 LAMP REPLACEMENT The average life of each lamp type is noted below Note that the lifetime of the lamp can be affected by the manner in which it is used Frequent ignitions contamination of the lamp envelope and an excessively hot operating environment all will lead to reduced lamp life To avoid system down time consider purchasing a replacement lamp as the lamp nears the end of its useful life Refer to the Section 3 4 of this manual for information on lamp installation APEX2 Model Lamp Type Lamp Model Average Lifetime APEX2 QTH 100W QTH 6338 500 hours APEX2 XE 100 W Xe 6252 1000 hours CLEANING Clean the exterior of the APEX2 when the illuminator is not hot from use Use a clean dry cloth Ensure that the ventilation holes are not blocked with dust Vacuum the openings if necessary from the outside of the unit When not in use cover the output port of the APEX2 Always be sure to remove the output port cover before turning on the lamp LAMP CARE AND HANDLING Do not allow any contaminants or fingerprints to adhere to the lamp envelope or reflector Always wear powder free gloves when handling lamps Handle the lamp by holding the outside of the reflector only If a lamp becomes contaminated do not use it before cleaning its envelope with isopropyl alcohol Dry completely before using If contaminants are not removed it may lea
21. he power off Do not use the power supply without its cover in place Lethal voltages are present inside Apex2 Illumination Systems Page 7 1 4 FIRE HAZARDS 1 5 Lamps are extremely hot during operation and for several minutes after being shut off Keep flammable objects away from the lamp and lamp housing Newport Research fan cooled Housings are equipped with a condenser lens The re focused output of this lens can cause ignition of flammable targets including but not limited to walls certain chemicals To avoid fire hazard use only the specified fuses with the correct type number voltage and current ratings as referenced in the appropriate locations in the service instructions or on the equipment Only qualified service personnel should replace fuses LAMP HANDLING Read all information and warnings provided with lamp The Xenon arc lamps used in one of the APEX2 models is filled with rare gas at high pressure so there is a danger of lamp explosion due to mechanical failure This is particularly true when the lamp is operating since the internal pressure can reach tens of atmospheres Thermal strains can cause the lamp to explode under certain conditions Never touch any lamp or the reflector s inner surface with bare fingers or other contaminates Skin oil or other substances can burn into the lamp envelope during operation and negatively affect the lamp s performance and lifetime Always wear appropriate gloves and i
22. he system was purchased It is suggested to save the packaging material and shipping container in case the equipment needs to be relocated at a future date WARNING Do not attempt to operate this equipment if there is evidence of shipping damage or there is suspicion that the equipment will not operate correctly Damaged equipment may present hazards CHOOSING A LOCATION Choose an installation location where the power requirements can be met for the system Be sure power is not applied to the system until the setup has been completed The environment should be that of a typical laboratory atmosphere without excessive humidity and contaminants in the air Do not allow the ventilation holes on the illuminator or its computer to be blocked Air should be able to circulate freely around the system Carry the instrument by its base plate When the system is placed in its final location check to ensure that none of the pre assembled items have become loose during transportation and handling Apex2 Illumination Systems Page 14 3 4 LAMP INSTALLATION Before plugging in the power cord and powering up the APEX2 the lamp must be installed The lamp is shipped in its own box to prevent damage during transportation It is suggested to keep this box as it can be utilized if moving or transporting the APEX2 in the future Never move the APEX2 while the lamp is installed Damage to the lamp or system may result ELECTRICAL SHOCK HAZARD
23. ibbon cable connectors for Oriel Cornerstone and MS257 monochromators USB cable connector for use with Universal Filter Wheel Utility software Figure 20 Filter Wheel Connectors Apex2 Illumination Systems Page 25 4 1 MANUAL CONTROL Pressing the pushbutton located on the back of the filter wheel as shown in Figure 21 advances the filter by one position Control the Filter Wheel by using the pushbutton to advance the filter position outlet Figure 21 Manual Control Configuration 4 2 DIRECT APEX2 COMPUTER CONTROL The APEX2 filter wheel comes with its own utility program and command set To utilize these control options connect the filter wheel directly to a computer using a USB cable Refer to Figure 22 for wiring connection information Section 7 discusses the utility program and command set in detail Control the Filter Wheel with a USB cable computer by using the filter wheel utility program or low level filter wheel commands outlet Figure 22 Direct Computer Control Configuration Apex2 Illumination Systems Page 26 4 3 MONOCHROMATOR UTILITY SOFTWARE CONTROL Oriel s Cornerstone and MS257 series monochromators include a utility program used to query and command the instruments When the filter wheel is connected to the monochromator the monochromator s utility program may be used to control both instruments Refer to the monochromator user s manual for more information Ensure the po
24. icable in addition to all shipping expenses Unless otherwise stated in Newport s repair quote any such out of warranty repairs are warranted for ninety 90 days from date of shipment of the repaired Product Oriel will charge an evaluation fee to examine the product and determine the most appropriate course of action Payment information must be obtained prior to having an RMA number assigned Customers may use a valid credit card and those who have an existing account with Newport Corporation may use a purchase order Apex2 Illumination Systems Page 53 When the evaluation had been completed the owner of the product will be contacted and notified of the final cost to repair or replace the item If the decision is made to not proceed with the repair only the evaluation fee will be billed If authorization to perform the repair or provide a replacement is obtained the evaluation fee will be applied to the final cost A revised purchase order must be submitted for the final cost If paying by credit card written authorization must be provided that will allow the full repair cost to be charged to the card 12 5 WARRANTY REPAIR If there are any defects in material or workmanship or a failure to meet specifications notify Oriel Instruments promptly prior to the expiration of the warranty Except as otherwise expressly stated in Oriel s quote or in the current operating manual or other written guarantee for any of the Products Oriel warrant
25. iguration 26 Figure 24 MS257 Monochromator Connections 27 Figure 25 Cornerstone USB Monochromator Connections 27 Figure 26 APEX2 Configured with Hand Controller i 28 Figure 27 Filter Selection Table In Trac Basie nc 29 Figure 26 Trs Gonttol Ridere lie 30 Fig re 29 MUTED MOD t 31 Figure 30 Collimating Lens AdjustMment 32 Figure 31 Do Not Adjust Relay LenS comics eE 32 Figure 32 Oriel 1 5 Inch Series Flange iii 33 Figure 33 Fiter Wheel Cover SChEWS iia 34 Figure 34 Filter Wrench Removing Retaining Ring sees enne 35 Figure 35 gt Installed FINE S atado loco toas ciat ev at Base om aaa 35 Figure 36 Setlb ADDIICAHOF ndo liso detenta ia eoo ciat evt Base om vule alite dir eda cuti muss 37 Figure 37 Destination Directory Selection 37 Figure 38 Accept License AGICEMEnN Srila 38 Figure 39 Start Installation nnne nennen nnns nna nnns ann n nnns nnns 38 Figure 40 Finish Installation nennen nennen nnn nnne nnne nn nnn nnn nenas 39 Figure 41 Restart Computer nnne nnne nnn nnne nnn nnns nna rn ness ina annis snae n ines naar rns 39 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Start Menu and Des
26. ime it is suggested to have a qualified electrician verify the wall socket to be used with the APEX2 meets the requirements for operation as noted The line voltage requirements for the APEX2 are as follows 100 to 120 VAC 50 60 Hz 200 to 240 VAC 50 60 Hz ELECTRICAL SHOCK HAZARDS To avoid electric shock connect the instrument to a properly earth grounded 3 prong receptacle only Failure to observe this precaution can result in severe injury or death Never attempt to open the lamp power supply or monochromator power adapter These items do not contain any user serviceable parts Failure to follow this warning can result in severe injury or death The APEX2 systems conforms to CE standards for both safety and EMC During normal use this equipment will not pose any electrical hazards to the user Read all warnings before installing or operating this system Never open the APEX2 cover and attempt to work inside without first turning the instrument off and disconnecting the power cord from the AC mains CAUTION Do not turn on the APEX2 until all connections have been made to the monochromator computer hand controller and or external 5 VDC source Refer to Section 4 for information on various methods and required connections to control the APEX2 If there are any questions or concerns contact Oriel Instruments or the regional sales representative for Newport WARNING When the power switch is turned on the lamp will beg
27. in emitting light immediately Do not turn on the APEX2 until the output flange is directed in such a way that people animals and equipment will not be harmed by the light A dedicated power line or line isolation may be required in certain locations as the electronics contained in the instrument are sensitive to static electricity and radiated electromagnetic fields Operation of the system near intense pulsed sources lasers Xenon flash lamps etc may compromise performance Apex2 Illumination Systems Page 22 Before making any electrical connections verify the power switches are in the OFF position for the APEX2 and monochromator if being used Connect the power cord to the back of the APEX2 before to plugging it into an AC electrical outlet NOTE Power switch is in the OFF position Figure 18 APEX2 Power Connection NOTE Always allow the lamp to warm up for at least 30 minutes prior to beginning work 3 6 Apex2 Illumination Systems Page 23 LAMP INTENSITY ADJUSTMENT APEX2 QTH ONLY The model APEX2 QTH includes a feature allowing the lamp intensity to be controlled by an external DC voltage source External control is enabled by moving the toggle switch on the back panel to the UP position When the toggle switch is in the DOWN position the lamp will operate at its full power rating of 100 watts The BNC female connector on the back of the APEX2 QTH is used to connect a DC voltage source The inpu
28. ktop Changes Connect to Filter Wheel Device ID Query Query Filter Position Fiber Focusing Assembly Model 6195 Optic Holder Beam Turning Reflector Holder Protective Gloves 49125 Safety Spectacles Fuse Compartment Apex2 Illumination Systems Page 4 Apex2 Illumination Systems Page 5 1 GENERAL INFORMATION Thank you for your purchase of this APEX2 illumination system from Oriel Instruments Please carefully read the following important safety precautions prior to unpacking and operating this equipment In addition please read the complete User s Manual for additional important notes and cautionary statements regarding the use and operation of the system 1 1 SYMBOLS AND DEFINITIONS CAUTION Situation has the potential to cause damage to property or equipment ELECTRICAL SHOCK HAZARD Hazard arising from dangerous voltage Any mishandling could result in irreparable damage to the equipment and personal injury or death WARNING Situation has the potential to cause bodily harm or death EUROPEAN UNION CE MARK The presence of the CE Mark on Newport Corporation equipment means that it has been designed tested and certified as complying with all applicable European Union CE regulations and recommendations Please read all instructions that were provided prior to operation of the system If there are any questions please contact Oriel Instruments or the representative through whom the system was purchased Apex2
29. lay Optics are set and locked during assembly Do not adjust under normal circumstances Relay Optics Shutter P Filter Knob Wheel Collimating Optics Figure 1 Basic System Block Diagram Apex2 Illumination Systems Page 10 NOTE All dimensions are in inches Figure 2 Dimension Diagram 0 1 Normalized Spectrum 0 01 200 400 APEX2 Illumination System Xe 600 800 1000 1200 1400 Wavelength nm Figure 3 Xenon Lamp Spectra Apex2 Illumination Systems Page 11 1600 1800 Normalized Spectrum 200 400 600 800 1000 1200 1400 Wavelength nm Figure 4 QTH Lamp Spectra Apex2 Illumination Systems Measured Ideal Blackbody 1600 1800 Page 12 2000 Apex2 Illumination Systems Page 13 3 SYSTEM SETUP 3 1 ITEMS INCLUDED WITH SYSTEM Oriel Instruments provides a pre aligned light source and filter wheel installed on a mounting plate In addition the system includes 3 2 3 3 Lamp APEX2 utility software Filter wrench 1 16 hex wrench Power Cord User s manual UNPACKING Remove all items from the shipping containers and verify each item is accounted for The system is carefully packaged to minimize the possibility of damage during shipment Inspect the shipping boxes for external signs of damage or mishandling Inspect the contents for damage If any item is missing or damaged immediately contact Oriel Instruments or the Newport representative from whom t
30. location or a different location To install software into a different location click the Browse button and select another directory There are separate directories for APEX2 and National Instruments Products as shown in Figure 37 Click Next to continue During the installation it is normal for other dialog boxes to flash as software is added Destination Directory Select the primary installation directory All software will be installed in the following locations To install software into a different locations click the Browse button and select another directory Directory for Universal Filter Wheel Utility C Program Files Newport Oriel Instruments Universal USB Filter Wheel Directory for National Instruments products C Program Files National Instruments lt lt Back Next gt gt Cancel Figure 37 Destination Directory Selection Apex2 Illumination Systems Page 38 5 Choose to accept the license agreements and click Next License Agreement ou must accept the licenses displayed below to proceed a NATIONAL INSTRUMENTS SOFTWARE LICENSE AGREEMENT INSTALLATION NOTICE THIS IS A CONTRACT BEFORE YOU DOWNLOAD THE SOFTWARE AND OR COMPLETE THE INSTALLATION PROCESS CAREFULLY READ THIS AGREEMENT BY DOWNLOADING THE SOFTWARE AND OR CLICKING THE APPLICABLE BUTTOM TO COMPLETE THE INSTALLATION PROCESS YOU CONSENT TO THE TERMS OF THIS AGREEMENT AND YOU AGREE TO BE BOUND BY THIS AGREEMENT IF YOU
31. lt 3000 m 9848 ft altitude IEC Classification Installation Category II Pollution Degree 2 Safety Interlock Lamp shuts off when cover is removed or when internal temperature exceeds normal operating conditions CE Compliance RoHS Compliance 10 2 UNIVERSAL FILTER WHEEL UTILITY SOFTWARE Microsoft Windows XP Service Pack 3 Microsoft Windows 7 32 bit and 64 bit Operating System Requires Microsoft net Framework 4 0 800 MB minimum Note One USB 2 0 port is required to connect between the computer and APEX2 filter wheel Additional USB ports may be required when controlling other instruments such as a monochromator lock in amplifier power meter etc Apex2 Illumination Systems Page 50 11 EU DECLARATION OF CONFORMITY We declare that the accompanying product identified with the C mark complies with requirements of the Electromagnetic Compatibility Directive 2014 30 EU and the Low Voltage Directive 2006 95 EC Model Numbers APEX2 XE APEX2 QTH Year C mark affixed 2014 Type of Equipment Electrical equipment for measurement control and laboratory use in industrial locations Manufacturer Newport Corporation 1791 Deere Avenue Irvine CA 92606 Standards Applied Compliance was demonstrated to the following standards to the extent applicable BS EN61326 1 2013 Electrical equipment for measurement control and laboratory use EMC requirements for use in a controlled electromagnetic envir
32. mpact resistant goggles when handling any lamp Avoid any mechanical strain during handling Do not operate the lamp without all housing panels in place Lamps become very hot after only a few minutes of operation up to 150 C and remain quite hot for at least 10 to 15 minutes after being turned off Apex2 Illumination Systems Page 8 2 INTRODUCTION The APEX2 series of illumination systems are designed as compact economical and fully integrated solutions for a wide variety of applications The APEX2 is a turnkey solution producing a collimated 1 3 inch 33 mm diameter output beam Just install the lamp connect the power cord and switch on the power then the system is ready for use The systems are available with either a Xenon or Quartz Tungsten Halogen QTH lamp Lamp replacement is easy no alignment is needed The lamp operates with a built in power supply so no current or power adjustments are required The APEX2 is designed with an ellipsoidal reflector capturing additional light to increase optical throughput The APEX2 is designed to be quick and easy to set up Mounting feet help with handling and leveling the illuminator The mounting feet are removable so the illuminator may be permanently mounted to an optical table if desired The APEX2 comes preassembled on a plate with mounting holes for securing the illuminator to an inch or metric optical table breadboard The light source is coupled to a filter wheel where u
33. onment This equipment meets the EN55011 2009 A1 2010 Class A Group 1 radiated and conducted emission limits BS EN 61010 1 2010 Safety requirements for electrical equipment for measurement control and laboratory use I c Mark Carroll Sr Director Instruments Business Newport Corporation 1791 Deere Ave Irvine CA 92606 USA Apex2 Illumination Systems Page 51 12 WARRANTY AND SERVICE 12 1 CONTACTING ORIEL INSTRUMENTS Oriel Instruments belongs to Newport Corporation s family of brands Thanks to a steadfast commitment to quality innovation hard work and customer care Newport is trusted the world over as the complete source for all photonics and laser technology and equipment Founded in 1969 Newport is a pioneering single source solutions provider of laser and photonics components to the leaders in scientific research life and health sciences photovoltaics microelectronics industrial manufacturing and homeland security markets Newport Corporation proudly serves customers across Canada Europe Asia and the United States through 9 international subsidiaries and 24 sales offices worldwide Every year the Newport Resource catalog is hailed as the premier sourcebook for those in need of advanced technology products and services It is available by mail request or through Newport s website The website is where one will find product updates interactive demonstrations specification charts and more To obtain informa
34. p to six neutral density or ordering sorting filters may be installed A large easy to read digital display indicates which filter is in the light path Filters are ordered separately as their specifications are application dependent The filters may be selected using a variety of methods including manual control and software For those who wish to create their own programs low level commands may be sent to the system via its USB connection to the computer The APEX2 includes a manually operated shutter It is important that the lamp is warmed up and stabilized when using the system When the lamp is not needed it can remain on and therefore warmed up by closing off the light path NOTE Always allow the lamp to warm up for at least 30 minutes prior to beginning work The output flange of the APEX2 is compatible with the 1 5 inch Oriel flanging system The collimated output may be coupled to a wide variety of items such as a beam turner focusing optics fiber optic cable adapter or detector Compatible instruments e Cornerstone 130 Monochromator e Cornerstone 260 Monochromator e MS260i Spectrograph e MS257 Monochromator e MS257 Spectrograph NOTE In this user s manual the term monochromator is used throughout the text The APEX2 may be operated with both monochromators and spectrographs Apex2 Illumination Systems Page 9 Filter Iis Selection Light Source Power Supply Hing Button Re
35. ppear on the desktop as shown in Figure 42 Apex2 Illumination Systems Page 41 7 3 USING THE FILTER WHEEL UTILITY SOFTWARE 1 After the Filter Wheel Utility software is installed and the computer restarted connect the APEX2 to the computer via a USB cable and turn on the illuminator 2 Run the utility program 3 Select the instrument and click the Connect button NOTE If the software is unable to connect check in the device manager to ensure that the USB driver has been installed correctly and the instrument is listed Universal Filter Wheel Utility Program vi ORIEL INSTRUMENTS Universal USB Filter Wheel Utility A Newport Corporation Brand E v1 0 USB RAW VISA resource name 1 UsB0 054130 0 1919 1809040503113400 R4WW D c Copyright 2014 Newport Corporation All Rights Reserved Figure 43 Connect to Filter Wheel 4 To verify communication click Device 1D e Universal Filter Wheel Utility Program vi ORIEL ii INSTRUMENTS Universal USB Filter Wheel Utility A Newport Corporation Brand aaa w1 0 Filter Selection T Filter 3 ES Device ID J J 77380 B Filters Disconnect c Copyright 2014 Newport Corporation All Rights Reserved Figure 44 Device ID Query Apex2 Illumination Systems Page 42 5 To select a filter click the pulldown menu and choose the desired filter position eS Pee NU DE Tec
36. ring using the filter wrench included with the system Insert the filter and re install the retaining ring Always wear gloves or finger cots when handing optics See Figure 34 and Figure 35 For all filter positions which are not being utilized ensure the retaining rings are snug so that they do not work themselves free and jam the filter wheel Only then should the filter cover be re installed Note Always keep track of which filters are installed at each position It is suggested to write down this information and update it whenever the configuration is changed This is particularly helpful in a multi user environment Apex2 Illumination Systems Page 35 Figure 35 Installed Filters Apex2 Illumination Systems Page 36 7 UNIVERSAL FILTER WHEEL UTILITY SOFTWARE The following procedure acquaint the first time user with the installation and use of the APEX2 utility software Do not be concerned if your display does not exactly agree with the figures shown The focus of this manual is to help the first time user learn how to install and use the software It is highly recommended that the first time user read these instructions before attempting to use or install the software To install the software the APEX2 utility software a compatible computer and a APEX2 illuminator are required Installation of APEX2 utility program will create e a folder called C Program Files Newport Oriel Instruments Universal USB Filter Wheel an al
37. s that for the period of time set forth below with respect to each Product or component type the Warranty Period the Products sold hereunder will be free from defects in material and workmanship and will conform to the applicable specifications under normal use and service when correctly installed and maintained Oriel shall repair or replace at Oriel s sole option any defective or nonconforming Product or part thereof which is returned at Buyer s expense to Oriel facility provided that Buyer notifies Oriel in writing prompily after discovery of the defect or nonconformity and within the Warranty Period Products may only be returned by Buyer when accompanied by a return material authorization number RMA number issued by Oriel with freight prepaid by Buyer Oriel shall not be responsible for any damage occurring in transit or obligated to accept Products returned for warranty repair without an RMA number Buyer bears all risk of loss or damage to the Products until delivery at Oriel s facility Oriel shall pay for shipment back to Buyer for Products repaired under warranty WARRANTY PERIOD All Products except consumables such as lamps filters etc described here are warranted for a period of twelve 12 months from the date of shipment or 3000 hours of operation whichever comes first Lamps gratings optical filters and other consumables spare parts whether sold as separate Products or constituting components of other Products
38. s to ensure that all its personnel protect the Newport Programs as trade secrets of Newport Corporation Customer shall not at any time disclose Newport s trade secrets to any other person firm organization or employee that does not need consistent with Customer s right of use hereunder to obtain access to the Newport Programs and Related Materials These restrictions shall not apply to information 1 generally known to the public or obtainable from public sources 2 readily apparent from the keyboard operations visual display or output reports of the Programs 3 previously in the possession of Customer or subsequently developed or acquired without reliance on the Newport Programs or 4 approved by Newport for release without restriction First printing 2014 2014 by Newport Corporation Irvine CA All rights reserved No part of this manual may be reproduced or copied without the prior written approval of Newport Corporation This manual has been provided for information only and product specifications are subject to change without notice Any change will be reflected in future printings Newport Corporation 1791 Deere Avenue Irvine CA 92606 USA
39. t voltage range is 0 to 5 VDC 0 VDC corresponds to the lamp being off 5 VDC allows the lamp to run at its maximum power of 100 watts NOTE In the event that the lamp isn t operating and no external voltage source is being applied check the toggle switch position and ensure it is in the DOWN position BNC connector for external DC voltage source External control enabled 0000000000 M ad Full power 100 watts eoccocoecoec 100 120 14AY asoy Figure 19 Lamp Intensity Adjustment Settings Apex2 Illumination Systems Page 24 4 CONTROLLING THE APEX2 FILTER WHEEL The APEX2 integrates a light source filter wheel and power supply Power is supplied to both the lamp and the filter wheel A large easy to read digital display indicates which filter is active i e which filter is in the light path The readout is positioned on the filter wheel assembly to face towards the rear of the light source so that it may be monitored from a safe and convenient viewing angle The filters may be selected using the following Manual pushbutton control Direct APEX2 computer control Oriel Monochromator Utility program Monochromator command set Monochromator Hand Controller Oriel TracQ Basic radiometry software For those who wish to create their own programs low level commands may be sent to the system via its USB connection to the computer Filter installation is covered in Section O Manual filter selection pushbutton 4 H
40. ternative directory may be chosen during the installation process e anicon called USB Filter Wheel Utility in the start menu e anicon for NI Max on the desktop 7 1 SYSTEM REQUIREMENTS Operating System Microsoft Windows XP Service Pack 3 Microsoft Windows 7 32 bit and 64 bit Requires Microsoft net Framework 4 0 Processor Speed 2 GHz minimum Random Access Memory RAM 1 GB minimum Peripheral Hardware CD ROM USB 2 0 port Hard Drive Space 800 MB minimum Apex2 Illumination Systems Page 37 7 2 SOFTWARE INSTALLATION PROCEDURE 1 Turn on the computer following the manufacturer s instructions Before installing the software close all applications Disconnect all instruments from the computer before installing this software Insert the Utility installation disk into the computers CD ROM drive The AutoPlay dialog box may open Select Open folder to view files If the AutoPlay does not start installing the software automatically open the contents of the installation disk Double click the Setup exe application shown in Figure 36 application to begin the installation d Di Filter Wheel Utility Program AE n Organize v Include in library Share with Mew folder EE 7 bin de license Je supportfiles jnidist id Sl setup exe setup ini Figure 36 Setup Application When the Destination Directory screen appears the option is available to install the software into the default
41. tion regarding sales technical support or factory service United States and Canadian customers should contact Oriel Instruments directly Oriel Instruments 150 Long Beach Boulevard Stratford CT 06615 USA Telephone 800 714 5393 toll free in United States 203 377 8282 Fax 203 378 2457 Sales oriel sales newport com Technical assistance oriel tech newport com Repair Service rma service newport com Customers outside of the United States must contact their regional representative for all sales technical support and service inquiries A list of worldwide representatives can be found on Oriel s website http www newport com oriel Apex2 Illumination Systems Page 52 12 2 REQUEST FOR ASSISTANCE SERVICE Please have the following information available when requesting assistance or service Contact information for the owner of the product Instrument model number located on the product label Product serial number and date of manufacture located on the product label Description of the problem To help Oriel s Technical Support Representatives diagnose the problem please note the following Is the system used for manufacturing or research and development What was the state of the system right before the problem Had this problem occurred before If so when and how frequently Can the system continue to operate with this problem or is it non operational Were there any differences in the application or environm
42. wer switches switch for the APEX2 and monochromator are in the off position marked as O Then connect the power adapter and all other cables to the monochromator as shown in Figure 25 The monochromator is connected to the APEX2 filter wheel using a ribbon cable provided with the APEX2 monochromator adapter kits Adapter kits are listed in Section 8 1 Connect the ribbon cable to the filter wheel using whichever connector matches the pin configuration of the cable Connect the other end of the power cord to the AC mains only after the lamp has been installed and all other connections made Once the APEX2 and monochromator are powered on the monochromator allows the user to select which filter is placed in the optical path Control the Monochromator and Filter Wheel with a computer by using the monochromator utility program or low level monochromator commands Ribbon cable USB Connector Filter Wheel Connector MONOCHROMATOR outlet Note that exact location of monochromator connectors varies based on model To AC power outlet Figure 23 Monochromator Control Configuration Apex2 Illumination Systems Page 27 FUSES 100 120 1 5 AT 250V 200 240 0 75 AT 250V Figure 24 MS257 Monochromator Connections Figure 25 Cornerstone USB Monochromator Connections Apex2 Illumination Systems Page 28 4 4 MONOCHROMATOR COMMAND SET For those who want to incorporate monochromator as well as APEX2 filter wheel
Download Pdf Manuals
Related Search