Ever Flo Ever Flo Q
Contents
1. Do not remove the covers of this device Servicing must be referred to an authorized and trained Respironics home care provider In the event of an equipment alarm or if you are experiencing any signs of discomfort consult your home care provider and or your health care professional immediately Oxygen generated by this concentrator is supplemental and should not be considered life supporting or life sustaining In certain circumstances oxygen therapy can be hazardous any user should seek medical advice prior to using this device Where the prescribing health care professional has determined that an interruption in the supply of oxygen for any reason may have serious consequences to the user an alternate source of oxygen should be available for immediate use Oxygen vigorously accelerates combustion and should be kept away from heat or open flame Not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide Do not smoke allow others to smoke or have open flames near the concentrator when it is in use Do not use oil or grease on the concentrator or its components as these substances when combined with oxygen can 8 P yg greatly increase the potential for a fire hazard and personal injury Do not use the oxygen concentrator if either the plug or power cord is damaged Do not use extension cords or electrical adapters Do not attempt to clean the concentrator while it is plugged int2. Yellow LED is blinking The Red LED is off and the The device has detected a high oxygen Audible Alarm is beeping periodically flow condition Connect to a back up oxygen source and Internal part failure l contact your home care provider The Audible Alarm is sounding continuously and all 3 LEDs are illuminated The airflow to the device is impeded Remove any items that appear to be or blocked blocking the airflow into the device mpeded oxygen flow indication is activated ar The flow meter knob is completely enon mer 7 The Yellow LED illuminates continuously counterclockwise to center the ball on the the Red LED is blinking and the Audible Alarm is prescribed LPM flow beeping periodically l The oxygen tubing is kinked and Check to see that the tubing is not kinked blocking the delivery of oxygen or blocked Replace if necessary Inspect and replace the items if necessary Limited oxygen flow to the user without any The oxygen tubing or cannula is faulty fault indication There is a poor connection to a device Ensure that all connections are free from All LEDs are off and the Audible Alarm is silent accessory leaks EverFlo EverFlo Q User Manual Chapter 5 Specifications Environmental Operating Transport amp Storage Temperature 13 to 32 C 34 to 71 C Relative Humidity 15 to 95 noncondensing 15 to 95 noncondensing Altitude 0 to 2286 m N A Ph
3. filter door on the back of the device as shown 2 Remove the humidifier connector tube from the back of the filter door and replace the filter door as shown 3 Fill your humidifier bottle according to the manufacturer s instructions 4 Mount the filled humidifier on the top of the EverFlo EverFlo Q device inside the velcro strap as shown in the illustration on the right RO 5 Tighten the velcro strap around the bottle and secure it so it is held firmly in place 6 Connect the humidifier connector tube that you retrieved from the filter door to the Oxygen Outlet Port as shown in Step 3 A above 7 Connect the other end of the humidifier connector tube to the top of the humidifier with the elbow in the tubing facing the front as shown here 8 Connect your cannula to the humidifier bottle according to the humidifier bottle manufacturer s specifications Step 3 B7 EverFlo EverFlo Q User Manual 4 Press the power switch to the On I position Initially all the LEDs will illuminate and the audible alert will beep for a few seconds After that time only the green LED should remain lit You can begin breathing from the device immediately even though it typically takes 10 minutes to reach oxygen purity specifications 5 Adjust the flow to the prescribed setting by turning the knob on the top of the flow meter until the ball is centered on the line m
4. ANCE AND MANUFACTURER S DECLARATION ELECTROMAGNETIC IMMUNITY This device is intended for use in the electromagnetic environment specified below The user of this device should make sure it is used in such an environment IMMUNITY TEST IEC 60601 Test COMPLIANCE LEVEL ELECTROMAGNETIC ENVIRONMENT LEVEL GUIDANCE Electrostatic Discharge ESD 6 kV contact 6 kV contact Floors should be wood concrete or ceramic IEC 61000 4 2 8 kV air 8 kV air tile If floors are covered with synthetic material the relative humidity should be at least 30 Electrical Fast Transient Burst 2 kV for power supply lines 2 kV for supply mains Mains power quality should be that of a IEC 61000 4 4 1 kV for input output lines 1 kV for input output lines typical home or hospital environment Surge 1 kV differential mode 1 kV differential mode Mains power quality should be that of a IEC 61000 4 5 2 kV common mode 2 kV for common mode typical home or hospital environment U Voltage dips short lt 5 U lt 5 U Mains power quality should be that of a interruptions and voltage gt 95 dip in U for 0 5 cycle 59596 dip in U for 0 5 cycle typical home or hospital environment If variations on power supply 40 U 40 U the user of the device requires continued input lines 60 dip in U for 5 cycles 60 dip in U for 5 cycles operation during power mains interruptions IEC 61000 4 11 70 U 70 U it is recommended that the device be 30 dip in U
5. Auew4ay 8014254 11228 Ul102S LUOLI S LMMM 30 N4 6210 80 91 7 150 ZT osseijsaqiomay 89941 Yd llIASAIInIN LZ9ESOL pue yosjneaq soluouidsay aue 7 sp M UNN 1001 2914044145934 dau 03 O 0 5210041455 EverFlo Q User Manual EverFlo EverFlo Q User Manual Table of Contents VADOR 2 HDDE LOTU nub 2 Chapter 1 ntroduction 3 Intended USER 3 About Your EverFlo 7 EVETF O Oz 3 Parts of Your Concentrator sssessseessseessseessseesssesssseosseessseeosseessseosssesssseoss 3 Accessory Equipment and Replacement Parts 3 Warnings and Cautions 22 4 Chapter 2 Operating nstruction s 5 Chapter 3 Cleaning 8 Maintenance 7 n 7 6006 rr bi 7 How to Contact ReSD TOniese a asi yaa da kis 7 Chapter 4 Alarms and Troubleshooting 8 Troubleshooting 9 Chapter 5 Specification s 10 Appendix A EMC Information 12 Limited Warranty mr 14 E
6. BA typical Classification The EverFlo EverFlo Q Oxygen Concentrator is classified as e TEC Class II Equipment Type BF Applied Part 1 1 Drip Proof Not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide e Continuous Operation Disposal Dispose of the device in accordance with local regulations WEEE ROHS Recycling Directives If you are subject to the WEEE RoHS recycling directives refer to www respironics com for the passport for recycling this product 11 EverFlo EverFlo Q User Manual Appendix A EMC Information GUIDANCE AND MANUFACTURER S DECLARATION ELECTROMAGNETIC EMISSIONSS This device is intended for use in the electromagnetic environment specified below The user of this device should make sure it is used in such an environment EMISSIONS TEST COMPLIANCE ELECTROMAGNETIC ENVIRONMENT GUIDANCE RF emissions Group 1 The device uses RF energy only for its internal function Therefore its CISPR 11 RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions Class B The device is suitable for use in all establishments including CISPR 11 domestic establishments and those directly connected to the public low voltage power supply network Harmonic emissions Class A k si wad IEC 61000 3 2 Voltage fluctuations Flicker emissions Complies IEC 61000 3 3 GUID
7. arking the specific flow rate Flow Meter Knob 6 Be sure oxygen is flowing through the cannula If it is not refer to the Troubleshooting Guide in this manual Put on the cannula as directed by your home care provider 8 When you are not using the oxygen concentrator press the power switch to the Off O position EverfF lo EverFlo Q User Manual Chapter 3 Cleaning 8 Maintenance Warning It is important to unplug the device before you perform any cleaning Caution Excess moisture may impair the proper operation of the device Cleaning Periodically use a damp cloth to wipe down the exterior case of the EverFlo EverFlo Q device If you use medical disinfectants be sure to follow the manufacturer s instructions If you are using a humidifier clean your device according to your home care provider s or manufacturer s instructions Service The EverFlo EverFlo Q Oxygen Concentrator contains no user servicable parts Warning Do not remove the covers of this device Servicing must be referred to an authorized and trained Respironics home care provider How to Contact Respironics To have your device serviced contact your home care provider If you need to contact Respironics directly call the Respironics Customer Service department at 1 724 387 4000 or Respironics Deutschland at 49 8152 93060 You can also use the following addresses Respironics Respironics Deutschland 1001 Murry Ridg
8. be life supporting or life sustaining About Your EverFlo EverFlo Q The device produces concentrated oxygen from room air for delivery to a patient requiring low flow oxygen therapy The oxygen from the air is concentrated using a molecular sieve and a pressure swing adsorption process Your home care provider will show you how to operate the concentrator and will be available to answer any questions If you have additional questions or problems contact your home care provider Parts of Your Concentrator Humidifier Bottle Mounting Strap Oxygen Outlet Air Inlet Filter Port Humidifier Connector Control Panel Tube On Off Switch Flow Meter Filter Door Accessory Equipment and Replacement Parts Contact your home care provider if you have questions about this equipment Use only the following Respironics accessories and replacement parts with this device Air Inlet Filter Humidifier Connector Tube EverFlo EverFlo Q User Manual VVarnings and Cautions Warnings A warning represents the possibility of harm to the operator or patient For proper operation your concentrator requires unobstructed ventilation The ventilation ports are located at the rear base of the device and at the side air inlet filter Keep the device at least 15 to 30 cm away from walls furniture and especially curtains that could impede adequate airflow to the device Do not place the concentrator in a small closed space such as a closet
9. e Lane Gewerbestrasse 17 Murrysville PA 15668 82211 Herrsching USA Germany Visit the EverFlo web site at www everflo respironics com EverFlo Q User Manual Chapter 4 Alarms and Troubleshooting Alarm and Indicators The device has an audible alarm and three LED indicators as shown below Green Power On Indicator Yellow Check System Indicator Red Alarm Indicator Audible Alarm Colored LED Possible Cause All 3 LEDs illuminate continuously and the Audible Alarm is sounding continuously The Audible Alarm is sounding continuously None of the LEDs are illuminated Red LED illuminates continuously and the Audible Alarm is sounding continuously Yellow LED illuminates continuously The Red LED is blinking and the Audible Alarm is beeping periodically Yellow LED illuminates continuously The Red LED is off and the Audible Alarm is silent The device has detected a system malfunction The device is turned on but is not operating Often this indicates that the device is not plugged in or there is a power failure The device has detected a system malfunction The device has detected an impeded oxygen flow condition The device has detected a low oxygen condition OPI units only Immediately turn off the device connect to a back up oxygen source and call your home care provider Check the power outlet and verify that the device is plugged in If the problem continues connec
10. e states or provinces do not allow the exclusion of limitation of implied warranties or the disclaimer of incidental and consequential damages Accordingly the laws of your state or province may give you additional protections To exercise your rights under this warranty contact your local authorized Respironics Inc dealer or contact Respironics Inc at Respironics Respironics Deutschland 1001 Murry Ridge Lane Gewerbestrasse 17 Murrysville PA 15668 82211 Herrsching USA Germany 1 724 387 4000 49 8152 93060 14
11. for 25 cycles 30 dip in U for 25 cycles powered from an uninterruptible power lt 5 U lt 5 U supply or a battery gt 95 dip in U_ for 5 sec 59596 dip in U for 5 sec Povver frequency 50 60 Hz 3A m 3A m Power frequency magnetic fields should be magnetic field at levels characteristic of a typical location in IEC 61000 4 8 a typical hospital or home environment Note U_ is the a c mains voltage prior to application of the test level 12 EverfF lo EverFlo Q User Manual GUIDANCE AND MANUFACTURER S DECLARATION ELECTROMAGNETIC IMMUNITY This device is intended for use in the electromagnetic environment specified below The user of this device should make sure it is used in such an environment IMMUNITY TEST IEC 60601 Test LEVEL COMPLIANCE LEVEL ELECTROMAGNETIC ENVIRONMENT GUIDANCE Portable and mobile RF communications equipment should be used no closer to any part of the device including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance Conducted RF 3 Vrms 3 Vrms 4 1 2 150kHzto 80XMHz IEC 61000 4 6 150 kHz to 80XMHz d 1 2NP 80MHzto 800 MHz Radiated RF 3V m 3V m d 2 3NP 800 MHz to 2 5 GHz EC 61000 4 3 80 MHz to 2 5 GHz VVhere P is the maximum output povver rating of the transmitter in vvatts VV according to the transmitter manufacturer and d is the recommended separation dista
12. nce in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey 8 should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol k Note 1 At 80 MHz and 800 MHz the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above the device should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the device b Over the frequency range 150 kHz to 80 MHz the field strengths should be less than 3 V m RECOMMENDED SEPARATION DISTANCES BETWEEN PORTABLE AND MOBILE RF COMMUNICATIONS EQUIPMENT AND THIS DEVICE The device is intended for use in an electromagnetic environment in which radiated RF di
13. nits serviced by Respironics or an authorized service center will be free from defects in serviced materials for a period of 90 days and free from defects in workmanship for a period of 90 days from the time of service Respironics accessories are warranted to be free of defects in materials and workmanship for a period of 90 days from the time of purchase If the product fails to perform in accordance with the product specifications Respironics Inc will repair or replace at its option the defective material or part Respironics Inc will pay customary freight charges from Respironics Inc to the dealer location only This warranty does not cover damage caused by accident misuse abuse alteration and other defects not related to material or workmanship Respironics Inc disclaims all liability for economic loss loss of profits overhead or consequential damages which may be claimed to arise from any sale or use of this product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty is given in lieu of all other express or implied warranties including the implied warranties of merchantability and fitness for a particular purpose In addition in no event shall Respironics be liable for lost profits loss of good will or incidental or consequential damages even if Respironics has been advised of the possibility of the same Som
14. o an electrical outlet Device operation above or outside of the voltage LPM temperature humidity and or altitude values specified may decrease oxygen concentration levels Your home care provider is responsible for performing appropriate preventive maintenance at the intervals recommended by the device manufacturer Cautions A caution represents the possibility of damage to the equipment Do not place liquids on or near the device If liquid is spilled on the device turn the power off and unplug from electrical outlet before attempting to clean up spill Call your home care provider if device does not continue to work properly EverFlo EverFlo Q User Manual Chapter 2 Operating Instructions Oxygen Outlet Port Warning Do not use extension cords or electrical adapters 1 Select a location that allows the concentrator to draw in room air without being restricted Make sure that the device is at least 15 to 30 cm away from walls furniture and especially curtains that could impede adequate airflow to the device Do not place the device near any heat source 2 After reading this entire manual plug the power cord into an electrical outlet 3 Do either Step A or Step B below A If you are not using a humidifier connect your nasal cannula to the Oxygen Outlet Port as shown in the top illustration on the right B If you are using a humidifier follow the steps below 1 Open the
15. sturbances are controlled The customer or the user of this device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and this device as recommended below according to the maximum output power of the communications equipment RATED MAXIMUM POWER SEPARATION DISTANCE ACCORDING TO FREQUENCY OF TRANSMITTER OUTPUT OF TRANSMITTER m 150 KHz To 80 MHz 80 MHz To 800 MHz 800 MHZ To 2 5 GHz 1 24 124 d 23 r For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer Note 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 13 EverFlo EverFlo Q User Manual Limited VVarranty Respironics Inc warrants that the system shall be free from defects of workmanship and materials and will perform in accordance with the product specifications for a period of three 3 years from the date of sale by Respironics Inc to the dealer Respironics warrants that the EverFlo EverFlo Q u
16. t to a back up oxygen source and call your home care provider Immediately turn off the device and wait 5 minutes Restart the device If the condition persists turn the unit off connect to a back up oxygen source and call your home care provider Follow the troubleshooting guide on the next page Connect to a back up oxygen source and call your home care provider if your troubleshooting actions fail to end this alert condition Continue using the unit but call your home care provider about this condition EverFlo EverFlo Q User Manual Troubleshooting Guide Why it Happened Turn the flow rate down to your prescribed level Wait at least 2 minutes If the condition persists turn the unit off connect to a back up oxygen source and call your home care provider Green LED illuminates continuously The other The device is turned on and working lensadisi LEDs are off and the Audible Alarm is silent properly The power cord plug is not properly Make sure the device is properly plugged a q inserted into the electrical outlet in to the electrical outlet The device is not working when it is turned on The unit is not receiving power from Check your household outlet fuse or The Audible Alarm is sounding continuously the electrical outlet circuit All LEDs are off Connect to a back up oxygen source and Internal part failure contact your home care provider The device is not working when it is turned on
17. verFlo Q User Manual Symbol Key gt 2808 EBH o IN N co Q Canadian US Cc s Certification Abbreviations LED Light Emitting Diode LPM Liters per Minute OPI Oxygen Percentage Indicator Follow Instructions for Use Type BF Applied Part Class l equipment No smoking No oil or grease Do not disassemble General Alarm European Declaration of Conformity REF SN 9 AC Power Model Number Serial Number On Power Off Power Drip proof equipment Action Required Check System Notification Compliant with the Waste Electrical and Electronic Equipment Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment WEEE RoHS recycling directives EverFlo is a trademark of Respironics Inc and its afhliates 2008 Respironics Inc and its affiliates All rights reserved EverfF lo EverFlo Q User Manual Chapter 1 ntroduction Your health care professional has determined that supplemental oxygen is of benefit to you and has prescribed an oxygen concentrator set at a specific flow setting to meet your needs DO NOT change the flow settings unless your health care professional tells you to do so Please read and understand this entire manual before using the device Intended Use The EverFlo EverFlo Q Oxygen Concentrator is intended to provide supplemental oxygen to persons requiring oxygen therapy The device is not intended to
18. ysical Dimensions 58cm x38 cmx 24cm Weight 14 0 15 kg Standards Compliance This device is designed to conform to the following standards IEC 60601 1 Medical Electrical Equipment Part 1 General Requirement for Safety IEC 60601 1 2 2nd edition Medical Electrical Equipment Part 1 2 General Requirement for Safety Collateral Standard Electromagnetic Compatibility Requirements and Tests 150 8359 Oxygen Concentrators for Medical Use Safety Requirements Electrical AC Povver Consumption Models 1020000 1020001 1020002 1020003 1020014 1020015 1020004 1020005 120 VAC 10 350 W 60 Hz 230 VAC 10 320 W 60 Hz 1020006 1020007 1020008 1020009 1020010 1020011 1020012 1020016 1020017 230 VAC 10 lt 300W 50 Hz 1020013 230 VAC 10 lt 300W 60 Hz 10 EverfF lo EverFlo Q User Manual Oxygen Oxygen Concentration All Models except 90 96 from 0 5 to 5 LPM 1020007 1020008 Models 1020007 1020008 87 96 from 0 5 to 5 LPM Device operation above or outside of the voltage LPM temperature humidity and or altitude values specified may decrease oxygen concentration levels Sound Level Models 1020000 1020001 1020002 1020003 45 dBA typical 1020013 1020004 1020005 1020006 1020008 1020009 1020010 43 dBA typical 1020011 1020012 1020016 1020017 1020007 1020014 1020015 lt 40 d
Download Pdf Manuals
Related Search