ekf 364 d ud ekf 411 d
Contents
1. Before doing any maintenance or cleaning jobs disconnect the appliance from the electrical mains and allow it to cool When the tilting door is wide open do not put anything on the surface because the door hinges could be irreparably damaged Do not attempt to carry out the periodic controls or any repairs by yourself Contact the nearest Service Centre and use only original spare parts N B Improper or incorrect use and failure to observe the installation instructions shall release the manufacture from all responsibility In this connection the directives in the POSITIONING paragraph must be strictly observed 3 Technical specifications EKF 411 D AL UD EKF 411 D UD EKF 311 D UD EKF 423 D UD EKF 443 D UD EKF 364 D UD EKF 464 D AL UD EKF 464 D UD Dimensions of appliance 590x695x590 675x725x560 790x750x505 790x785x635 790x750x635 LxDxH mm a 9 a 58 Convection heating element kW a 3 on 3 29 32 a 230 V 50 60FE 3x1 5 mm Class us MW NYyHOL O Degree of protection IPX3 against humidit The noise level of the appliance in operation is below 70 dB A The technical data plate is positioned on the rear panel of the appliance page 4 Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD 4 Instructions for the installer The following instructions are aimed at the qualified i2. Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD Index Technical service General warnings Technical specifications Instructions for the installer Use instructions for the user Residual risks for the user How to use the control panel Ignition BOD gt i a a ad Switch off o Operation mode Cooking cycle ON OFF N Displaying changing parameters with the cooking cycle ON UJ Delayed start to the cooking cycle D Programmed mode _ ul Saving cooking programs on Cooking with a saved program N Manual humidifying Door device Oo Black out _ tO N o Oven cooking N Routine cleaning and maintenance N N Possible faults Technical assistance N WwW N N Informations to the consumers N ul Wiring layouts The Warranty N on page 3 TECNOEKA Srl use and instruction manual 1 Technical service A technical check up once or twice a year helps prolong the life of the appliance and guarantees better operation Make sure that assistance is carried out solely and exclusively by qualified personnel For any spare parts orders or for any information about the appliance
3. J pan WiL a me a HH l amp E l E 2 i Ba E rr Mr a HEH EU EF ay ER HA AB O ga HH Ee iil Hf Ee EB HB a EM EB Wn i oe 7 Hu aH yy BH Es gin E MEH HAN FE go MH in Eu Burum BH Hn g eid Wagi Ud sd inen H Hb 1 Eis Wis BY Jo Ee dud Hed erdd i tin tsj UE C 4 BU bam arg mm a in EB un med 7 HHE Mmm Ed Msss EHH HEHHEHE NSE tis H WEL ga Mr Hy GED Hy isansannau FETH GH USE AND INSTRUCTION MANUAL MODD EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD rev 1 TECNOEKA S r l Via Marco Polo n 11 35010 Borgoricco Padova Italy Tel 39 049 9300344 39 049 5791479 Fax 39 049 5794387 www tecnoeka com E mail info tecnoeka com TECNOEKA SRL VIA MARCO POLO 11 35010 BORGORICCO PADOVA ITALY TEL 39 049 5791479 39 049 9300344 FAX 39 049 5794387 E MAIL INFO TECNOEKA COM WWW TECNOEKA COM WWW TECNOEKA RU COD FISC P IVA 00747580280 REA N 133205 CAP SOC EURO 119 000 00 I V CE DECLARATION OF CONFORMITY Annexed document Il A of directive 2006 42 EC Manufacturer s name TECNOEKA Srl Manufacturer s address Via Marco Polo 11 35010 Borgoricco PD Manager s name of technical file Minotto Lorenzo Manager s address of technical file Via Marco Polo 11 35010 Borgoricco PD Type of product Electronic oven Pur
4. always mention the serial number and model data indicated on the technical data plate at the rear of the oven 2 General warnings Very important keep this instruction book together with the appliance for future consultation These warnings were drafted for your safety and for that of others Please read them _ carefully before installing or using the appliance If on receipt of the goods the packaging is damaged write the following on the delivery note I REVERSE THE RIGHT TO CONTROL THE GOODS specify the damage and get the driver to sign in acceptance send a claim in writing to the seller within 4 calendar days from the date of receipt No claim shall be accepted after such period The warehouse inside temperature must not be lower than 99C otherwise the thermostat regulation and safety thermostat control devices of the machine will be damaged Failure to observe this prohibition invalidates any responsibility of the manufacturer of the machine The appliance is intended for professional use and must be utilised by qualified personnel trained to use it Any modification which may be necessary on the electrical system to enable installation of the appliance must be carried out solely by competent personnel _ It is dangerous to modify or attempt to modify the characteristics of this appliance Never clean the appliance with direct water jets because if any water enters it could limit the machine s safety
5. are set for the new cooking cycle The new program must be saved by pressing the button 16 Cooking with a saved program Follow the steps below to run a saved cooking program press the button PO1 appears on the display Press buttons and select the required program number Press button P H appears on the display cooking chamber preheating function The oven operates until it reaches a temperature equal to the value set for step 1 programmed cycle increased by 30 C When the preheating temperature is reached P H blinks on the display and the buzzer sounds At this point open the oven door introduce food to be cooked and close the door the buzzer turns off and the programmed cooking cycle starts page 11 TECNOEKA Srl use and instruction manual N B the preheating function Is available automatically started only in programmed cooking modes When the oven Is operating in programmed mode set parameters can be displayed in the same way as with manual mode For the user s convenience set parameters can be changed during oven operations in programmed mode At the end of the programmed cooking cycle changed parameters are automatically RESET and return to the values initially saved in the program 17 Manual humidifying Humidity can be produced in the cooking chamber water solenoid valve on or activation of water pump at any time in the cooking cyc
6. due to a manufacturing fault on condition that under penalty of forfeiture for domestic equipment the customer notifies the fault within two months from the date when he she discovered it and anyway within 2 years form the date of purchase for professional equipment the customer notifies the fault within 8 days from the date when he she discovered it and anyway within 12 months from the date of purchase by registered letter with acknowledgement of receipt and enclosing the invoice or receipt proving the purchase Apart from the case when the customer cannot produce the invoice or receipt proving the purchase or when the above mentioned terms are not complied with the warranty is expressly excluded in the following cases 1 faults or breakage caused by the transport 2 wrong or incorrect installation of the product for instance because of insufficient draught of the flue or exhausts in light of the instructions given in the user s handbook supplied with the product 3 inadequate or abnormal electrical hydraulic and or gas supplies 4 carelessness negligence or incompetence in using the product in light of the instructions given in the user s handbook supplied with the product 5 use of the product for uses different from the one for which it was built or anyway in a manner not compliant with the instructions given in the user s handbook supplied with the product 6 tampering with the product 7 adjustments and or
7. maintenance and or repairs carried out by unauthorised personnel and or with non original spare parts 8 inadequate or careless maintenance of the product in contrast with the user s handbook supplied with the product 9 damages caused by fire natural disasters and accident as well as by any cause not attributable to TECNOEKA SRL The warranty explicitly excludes varnished or enamelled parts knobs handles movable or removable plastic parts bulbs glass parts refractories and any accessories TECNOEKA SRL cannot be held responsible for any damages either direct or indirect caused by the product breaking down or following its non use Any repairs carried out during the warranty do not cause said warranty to be extended or renewed Nobody is authorised to modify the terms and conditions of the warranty or to issue new verbal or written warranties The warranty is valid only for appliances installed in the European Union Any dispute shall be settled by the competent Court in Padua Warning for the Buyer 1 the cooking appliance is designed only for cooking purposes while the heating appliance is designed only for heating domestic environments 2 TECNOEKA S r l does not install the appliances the seller shall be responsible for any installation carried out 3 TECNOEKA S r l cannot be held responsible for any damages either direct or indirect to people pets or property caused by the appliance breaking down or following i
8. steps for 4 seconds led blinks on symbol O y Temperature parameter The value set for the selected step led on symbol E is displayed for 4 seconds alternated by the value read in the cooking chamber for 4 seconds led blinks on symbol 10 Humidity parameter The set value is displayed for the selected step fixed led on symbol amp Heart temperature parameter for ovens predisposed The display will cycle for 4 seconds the value set for the selected phase LEDs mounted on symbol O and for 4 seconds the measured value within the food LED flashing on symbol N B If you have not connected in the socket the thermal probe shaped pin instead of reading the writing appears _ _ _ 13 Delayed start to the cooking cycle To delay the start for the cooking cycle proceed as follows e Set the reguired parameters for each phase in the cooking cycle following the instructions in the paragraph OPERATING METHOD paragraph 10 e Press the pwer key until all the signal leds go out on the control panel The message 0 00 appears on the display page 10 Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD e Press the E A keys and set the required DELAY TIME on the display maximum 9 hours and 59 minutes e Press the key to activate the delayed start The led on the Bl starts fl
9. the display shows alternatively the time set for the active phase and the total time for all stages of the cooking cycle The cooking cycle ends when the temperature detected by the probe introduced in the food reaches the value sets in the parameter core temperature Regardless of the value of the parameter time Warning Before removing the food from the oven after cooking with the core needle probe Carefully remove the hot probe from the cooked food taking care not to leave it hanging out of the cooking chamber as it could cause burns We advise leaving it to cool down before using it again to avoid damaging pricks in the food To prevent any irreparable damage to the thermal piercing probe core probe do not use It in high temperature cooking ABOVE 230 C and ensure that the probe lead is not touching any hot metal surfaces inside the oven 21 Routine cleaning and maintenance WARNING Cut power to the appliance before every operation General cleaning Clean the oven when it is cold Wash enamelled parts with lukewarm water and soap do not use abrasive products steel wool or acids which could ruin them To clean the steel parts do not use products containing chlorine sodium hypochlorite hydrochloric acid etc even if diluted Use specific off the shelf products or a little hot vinegar Rinse thoroughly with water and dry with a soft cloth Clean the glass door of the oven with hot water only and do not use rough cl
10. D UD EKF 311 D UD EKF 364 D UD To access the terminal board just remove the appliance s rear side panel Loosen the cable gripper and allow the cable to pass through it Arrange the conductors so that the earth conductor is the last to detach from its terminal if the cable goes into a state of faulty traction Connect the phase conductor to the terminal marked L1 connecting the neutral conductor to the terminal marked N and the earth conductor to the terminal marked with the symbol Tighten the cable gripper and re fit the rear side panel of the appliance Modd EKF 411D UD EKF 464 D UD EKF 411 DAL UD EKF 464 D AL UD To access the terminal board just remove the ppliance s rear side panel Loosen the cable gripper and allow the cable to pass through it Arrange the conductors so that the earth conductor is the last to detach from its terminal if the cable goes into a state of faulty traction Connect the phase conductors to the terminals marked L1 and L2 connecting the neutral conductor to the terminal marked N and the earth conductor to the terminal marked with the symbol according to the following lay out 220 230v 380 400v 2N P TT EDT this electrical connection lay out is located near the power supply terminal board Tighten the cable gripper and re fit the rear side panel of the appliance Any appliance must be connected to an equipotential system whose efficiency must first be c
11. ashing to show that the COUNTDOWN has started shown on the display The DELAY TIME can be changed at any moment during the COUNTDOWN by pressing the BE keys When the DELAY TIME is up the cooking cycle will start automatically To zero the DELAY TIME just press the s the display will show the operating parameters than can be changed Press the again to continue the cooking cycle otherwise a delayed start for the cooking cycle can be reset by proceeding as above N B in case of BLACKOUT or power failure during the COUNTDOWN the programmed delay for the cooking cycle is cancelled and all the relative set parameters are zeroed A delayed start to the cooking cycle is only possible in MANUAL MODE It cannot be included in a programmed cooking cycle 14 Programmed mode Up to 99 cooking programs cycles can be saved Each program can include 1 or more cooking steps up to 4 15 Saving cooking programs Follow the steps below to save a cooking program press the button Eg led on PO1 appears on the display Press buttons and select the required program number up to P99 Set the relevant cooking cycle parameters following the same procedure used for manual mode Press and hold down the a button for at least 5 seconds the program is successfully saved with the saved program number blinks on the display To cancel a saved program simply replace it with a new program with the same number where new
12. eart temperature parameter because it is operating must be set before starting the cooking cycle page 9 TECNOEKA Srl use and instruction manual 11 Cooking cycle ON OFF The cooking cycle starts and stops by pressing the button The resistance motor and water solenoid valve are switched off at the end of the cooking cycle The buzzer sounds for 30 seconds and 0 00 blinks on the display Temperature humidity parameter settings for the last cycle step remain set If an extra time is set during the next 30 seconds the oven automatically restarts and cooking continues with the temperature and humidity parameters for the last step used When extra time has elapsed the cooking cycle ends If the 30 seconds elapse or the cooking cycle is interrupted by pressing the button all set parameters are reset and the oven readies for new cooking cycle settings 12 Displaying changing parameters with the cooking cycle ON When the cooking cycle is on parameters can be E by pressing the saer button and values can be changed keys BW in each step button in the cooking cycle Several seconds after the last change for any of the four steps operating step parameters are displayed led blinks on current step f the L Time parameter Is selected The value set for the selected step led on symbol 6 is displayed for 4 seconds alternated by the remaining total COUNT DOWN for the rest of the other
13. h borders higher than 20mm avoid that products into the pan get in contact Warm up the oven before every cooking operation set a temperature 30 C higher than cooking temperature to obtain maximum uniformity Do not salt foods in the cooking compartment 6 Residual risks for the user After a cooking operation open the door cautiously to avoid a violent outflow of heat which could cause burns While the oven is in operation pay attention to the possible hot zones marked on the appliance of its external surfaces Place the machine on a bench or similar support at a height of at least 85 cm from the floor The bench or support must be able to support the weight of the machine and house it correctly The appliance contains electrical parts and must never be washed with a jet of water or steam The appliance is electrically connected before attempting any cleaning operation cut power to the appliance Do not use the door handle to move the appliance the glass panel may break When the tilting door is wide open there is the risk that things could be placed on the surface with the risk of irreparably damaging the door hinges 7 How to use the control panel Control Panel symbol legend 1 2 3 5 67 8 9 10 11 1 Parameter on signal LED 7 Parameter value increase button 2 Cooking parameter selection button 8 Cooking program select save button 3 Step on signal LED 9 Manual humidifying button 4 Cooking step selection butt
14. he factory the appliance was completely regulated and tested by expert specialised personnel to guarantee the best operating results All repairs and settings must be performed with utmost care and attention respecting national safety regulations in force Always contact your retailer or our nearest Service Centre giving details of the problem the appliance model and the serial number on the rating plate on the rear panel For any maintenance the user can contact Tecnoeka by calling the telephone numbers on the cover or going to www tecnoeka com 24 Informations to the consumers Further to Directive 2002 96 EC the symbol of the crossed rubbish skip on the appliance means that at the end of its life the product must be disposed of separately from the other rubbish The user must hand the appliance to a specialised waste collection centre for electric and electronic equipment The separate collection of the rubbish and subsequent treatment recovery and disposal help to produce other equipment using recycled materials reducing the negative effects on the environment and public health which would be caused by incorrect management of the rubbish Should the user dispose of the product abusively administrative sanctions would be applied pursuant page 15 TECNOEKA Srl use and instruction manua 25 Wiring layouts T1 SD page 16 MODD EKF 423 D UD EKF 443 D UD Power terminal board Safe
15. hecked according to current legal regulations This connection must be made between different appliances by using the appropriate terminal marked with the symbol The equipotential conductor must have a minimum diameter of 2 5mm The equipotential terminal is at the rear of the appliance Safety thermal breaker The appliance is supplied with a manually resetting thermal breaker to protect against excessive dangerous temperatures which could be accidentally generated inside If it is tripped the device cuts off the power supply to the appliance page 7 TECNOEKA Srl use and instruction manual 5 Use instructions for the user For first use we advise you to let the appliance to run load free for 30 40 minutes at a temperature of 200 C In this way any unpleasant smells due to thermal insulation and residual work grease are eliminated This appliance must be used solely for the purpose for which it was expressly designed i e cooking foods in the oven Any other use is considered unsuitable The appliance can be used for all oven cooking of deserts pizzas meat fish vegetables as well as for re conditioning cooled and frozen foods When placing food in the cooking compartment leave a space of at least 40 mm between pans in order not to over obstruct air circulation Do not use pans with higher than necessary edges edges are barriers which prevent the circulation of hot air for cooking of bread and pastry do not use pans wit
16. l data plate the power supply system has an adequate earth connection according to current legal regulations a omnipolar switch with minimum between contacts aperture of the overvoltage category lll 4000 V sized to the load and conforming to current legal regulations is fitted between the appliance and the mains in the direct connection to the mains the omnipolar switch used for connection is easy to reach when the appliance is installed the yellow green earth wire is not interrupted by the switch the power supply when the appliance is operating must not deviate from the rated voltage value by 10 make sure that after inserting the power supply cord into the terminal block it does not come into contact with any of the cooking range s hot parts if the supply cable is damaged then it must be replaced by the manufacturer or by your technical support or by a qualified person to avoid any risk Connection to the water mains for ovens predisposed to humidifier solenoid valve The appliance must be fed with softened drinking water with pressure in the range from 100 to 200 kPa 1 0 2 0 bar Water must have hardness from 0 5 F to 3 F it is suggstible to use a softener as to avoid the malfunction of the fan the breakage of the heating element and to reduce the formation of lime inside the cooking chamber Connection to the water mains should be made through the threaded 3 4 solenoid valve on the rear on the b
17. le in both manual and programmed mode by pressing the button led on Continuous humidity as long as the button is pressed If an automatic humidifying cycle is in progress press button D water solenoid valve on or activation of water pump to interrupt it Release the automatic humidifying cycle button to resume 18 Door device The device stops oven operations stops the cooking cycle whenever the door is opened The cooking cycle resumes where it left off when the door is closed 19 Black out When power returns after a black out the oven automatically resumes operations and the cooking cycle resumes from where it left off 20 Oven cooking Cooking techniques There are two different cooking techniques with this oven convection and convection humidification Convection cooking Heat is transferred to the foods by pre heated air forced to circulate by in the cooking chamber The heat quickly and uniformly reaches all parts of the chamber enabling simultaneous cooking of different types of food providing they have the same cooking temperature placed on the shelves without mixing tastes and smells Convection cooking is particularly convenient for rapid de freezing and for sterilising preserves and drying mushrooms and fruit Cooking Convection humidification The fact of using a hot moist climate inside the cooking chamber with variable temperature and moisture levels is the most convenient and efficient wa
18. ly for MODD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD A drain pipe see Fig 2 comes out from the rear of the appliance to drain the oven cavity This pipe must be connected up to a pipe made to resist steam temperatures 90 C 100 C with an internal diameter of 30 mm DN 30 To prevent choking it is best to use a rigid pipe and make sure there are no elbow bends anywhere along the drain line Furthermore the drain line must slope down minimum slope 5 along its full length the length in question is from the appliance s drain pipe to the drain point and must not exceed 2 metres The drain line must run into an open floor drain Fig 3 In addition there must be a free air gap of at least 25 mm distance between the drain line coming from the appliance and the funnel on the drain standpipe Whatever the case in order to comply with current hygiene standards the line connected to the appliance s drain pipe must not come into direct contact with the drain point It is advisable to include a suitable trap in the line connecting the appliance s drain outlet to the grey water waste system thus stopping the steam coming back out of the drain page 6 Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD max 2000mm max 2000mm FIG 2 FIG 3 Connecting the power cable Mod EKF 423 D UD EKF 443
19. nstaller to ensure that he carries out the installation adjustment and maintenance operations as correctly as possible and according to current legal regulations Any operation must be performed with electrical power cut to the appliance Before using the appliance carefully remove the special adhesive film protecting the parts in stainless steel Do not leave any glue residues on the surfaces If necessary remove them at once with an appropriate solvent Fitting the feet The feet are inside the appliance and must be secured on the four threaded holes on the base If necessary the height of the feet can be adjusted by screwing or unscrewing Positioning Position the appliance perfectly horizontally on a table or similar support the table or support must be at least 85 cm above the floor Position it at a distance of not less than 10 cm from the side and rear walls to enable natural ventilating air to circulate freely around it The appliance is not suitable for embedding and for grouped positioning with other identical appliances Electrical connection The appliance must be connected to the electrical mains according to current legal regulations Before making the connection make sure of the following the voltage and frequency values of the power supply system match the values on the technical data plate affixed on the appliance the limiting valve and the system are able to support the appliance s load see the technica
20. on 10 START STOP button 5 Parameter display 11 Probe core outlet for ovens predisposed 6 Parameter value decrease button page 8 Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD 8 Ignition The control panel digital automatically turns on as soon as the oven is electrically powered 0 00 appears on the display to indicate time expressed in hours and minutes and the time led turns on in the parameter field symbol The phase 1 led turns on in the phase field set to receive cooking parameters 9 Switch off The control panel automatically turns off10 minutes after the cooking cycle ends in manual mode or in automatic mode whether switched off automatically or by pressing the button without any button being pressed The display and operating function leds turn off Only the EU button led remains on To restart the control panel simply press the a button 10 Operation mode The cooking cycle can be run in manual or programmed mode which can be divided in 4 Steps TIME TEMPERATURE HUMIDITY HEART TEMPERATURE cooking parameters can be set for each step MANUAL MODE To select cooking parameters TIME TEMPERATURE HUMIDITY HEART TEMPERATURE press the button seer the led for the selected parameter turns on each time the button is pressed At least cooking time and
21. orresponding rings for airproofing and power up the appliance 22 Possible faults Type of fault Cause Corrective action Control panel completely off the oven does not work Incorrect electric connections to the mains Check the mains connection No mains voltage Restore mains voltage Thermal break safety device tripped Reset the thermal break safety device Electronic card protection fuse control panel burnt Contact a qualified technician Cooking cycle set and push button pressed the oven does not work Door open or ajar Close the door Damaged door switch device Contact a qualified technician to repair the sensor Humidity production in cooking chamber on No water flows from the pipes on the fans Incorrect connection to water mains Connection of non conforming pump Check the connection to water mains electrovalve or the connection of pump Cut off cock closed electrovalve Tank without water pump Check the cut off cock Check water level into the tank Blocked water inlet filter Clean the filter Electrovalve or pump water entrance damaged Contact a qualified technician to repair the solenoid Door closed water vapour comes out of the seal Seal not fitted correctly Check the seal fitting Damaged seal Contact a gualified technician to repair the seal Handle mechanism loosened lateral opening door Contac
22. oths Do not allow foods especially acid foods such as salt vinegar lemon etc to stagnate on the stainless steel parts because they could deteriorate Do not wash the appliance with direct jets of water because if water enters this could limit the appliance s safety Do not use corrosive substances e g hydrochloric acid to clean the oven s support bench Cleaning the oven It is good practice to clean the oven interior at the end of every day of duty In this way it will be easier to remove cooking residues preventing them from burning when the oven is next used Clean it accurately with hot water and soap or with the appropriate off the shelf products Cleaning the oven door Except modd EKF 411 D AL UD EKF 464 D AL UD To clean the oven door thoroughly proceed as follows fully open the door insert the equipped plugs in the A holes on the hinges Fig 4 lift the door gently and withdraw it Fig 5 put back the door in the initial position by operating inverserly page 13 TECNOEKA Srl use and instruction manual Replacing oven lamp Electrically switch off the appliance unscrew the protective glass cap with the corresponding rings for airproofing unscrew the lamp and replace it with another lamp suitable for high temperatures 300 C with the following characteristics Voltage 230 240 V Power 15 W Fitting E14 Refit the glass cap with the c
23. ottom of the appliance fitting in between a mechanical filter and an on off tap before you connect the filter allow a certain quantity of water to flow out in order to drain any waste from the pipe page 5 TECNOEKA Srl use and instruction manual Connection to water tank for ovens predisposed to water pump To replace electrovalve with water pump in ovens with optional predisposition to pump follow the steps below listed image 1 1 Remove back cover from oven 2 Disconnect wiring cables from electrovalve 3 Disconnect water tube 3 from electrovalve pressing e keeping pressed the edge of black linking quick insertion 4 Remove the electrovalve unscrewing the screw that fix it to oven s frame 5 Fix the pump 1 to the frame with the appropriate support 2 and the two screws 4 included 6 Connect the cables previously disconnected from electrovalve to pump 7 Connect the tube previously disconnected from electrovalve to pump s linking 8 Connect the tube 6 with filter and ballast included in Pump kit to pump s apron 7 9 Replace back cover Fig 1 Warning To avoid limestone buildup into the cooking chamber we suggest to fill the water tank with decalcified water Check water level in the tank before activating the pump and during its functioning If pump works without water in the tank what occurs is abnormal noise at first and then its breakage Water drainage on
24. pose of the product Cooking food Models EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD TECNOEKA Srl declares that the mentioned above products meet the following safety regulations Low voltage directive 2006 95 CE Electromagnetic compatibility Directive 2004 108 CE TECNOEKA Srl declares that the mentioned above products meet the following harmonised standards CEI EN 60335 1 CEI EN 60335 2 42 IEC EN 55014 1 IEC EN 55014 2 IEC EN 61000 3 2 IEC EN 61000 3 3 IEC EN 61000 4 2 IEC EN 61000 4 4 IEC EN 61000 4 5 IEC EN 61000 4 6 IEC EN 61000 4 11 IEC EN 62233 TECNOEKA Srl declares that the mentioned above products meet the following directives Machine Directive 2006 42 CE Directive on the general safety of products 2001 95 CE Directive on the restriction in the use of dangerous substances in electrical and electronic appliances 2011 65 CE Directive on waste from electrical and electronic appliances 2002 96 CE RAEE TECNOEKA Srl declares that the mentioned above products meet the CE 1907 2006 REACH Regulation te sf he Ne Borgoricco 10 10 2014 Signature ofa Repres ntativ of the Board of directors CRISTINA LORA X A Sgq PRODOTTI Fam 1 FORNNFORNO ELETTRICO LEKa MANUALI D USO Forno Elettrico 40 60 90 LEka Lingua Inglese NUOVA GAMMA EF Instruction manual DIGITAL LINE GB rev 1 doc page 2
25. t a qualified technician to repair the prong The oven does not cook evenly One of the motors is blocked or turns slowly If the oven has two motors Contact a qualified technician to repair the motor The motors do not go into reverse Contact a qualified technician to repair the motor Heating element not powered or is damaged Contact a qualified technician to repair the element Lighting lamp in the cooking chamber does not work Damaged lamp Change the lamp Light bulb unscrewed Make sure the light bulb is fully screwed in ER1 appears on the display Breaking in the connection between the cooking chamber probe electronic card and the control panel Check the connection to the control panel Damaged cooking chamber probe Contact a gualified technician to repair the probe for ovens predisposed Core temperature activated led on to the symbol B and probe connected to the control panel the message appears on the display u Break in the connection between the core probe electronic power card Check the connection to the electronic card Damaged core needle probe Contact a gualified technician to repair the probe page 14 Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD 23 Technical assistance Before leaving t
26. temperature parameters must be set for the cooking u to start e To select cooking cycle steps 1 2 3 4 press the button the led relevant to the selected step turns on each time the button is pressed The led relevant to the current step blinks during the cooking cycle e To set or change the selected parameter press buttons mm Press button B to increase the parameter Press button B to decrease the parameter e The time parameter symbol can be set from O hours and 01 minutes to 9 hours and 59 minutes If INF or HLD appear on the display this means that the timer is excluded The oven operates continuously until manually turned off with the a button When INF appears on the display only displayed for step 1 steps 2 3 4 are disabled leds off When HLD appears on the display only displayed for step 4 this means that the cooking cycle after terminating the previous steps continues without the timer and with the parameters set for phase 4 The cooking cycle is switched off by pressing the a button This operation lets the user keep food warm at the end of the cooking cycle for the desired amount of time The temperature parameter symbol 9 can be set from 50 C to 270 C The humidity parameter symbol can be set from O to 100 continuous humidity The heart temperature parameter symbol g can be set from 0 C to 100 C for prepared oven N B the h
27. ts non use The Manufacturer cannot be held responsible for any inaccuracies due to misprints or mistakes in copying in this handbook The Manufacturer reserves the right to modify the products as he deems fit also in the interest of the user without affecting the vital characteristics of functionality and safety page 19
28. ty thermostat Door microswitch Electronic card Humidifier solenoid valve Fuse Key Ox lt lt nr w N Contactor coil Oven lighting lamp Circular heating element Oven motorised ventilator Tangential motorised ventilator Capacitor Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD MODD EKF 311 D UD EKF 364 D UD Key M Power terminal board B1 B2 Contactor coils T1 Safety thermostat R Circular heating element SD Electronic card V1 Oven motorised ventilator MI Door microswitch V2 _ Tangential motorised ventilator F Fuse C Capacitor E Humidifier solenoid valve L Oven lighting lamp page 17 TECNOEKA Srl use and instruction manua MODD EKF 411 D AL UD EKF 464 D AL UD EKF 411 D UD EKF 464 D UD M Power terminal board T1 Safety thermostat SD Electronic card MI Door microswitch E Humidifier solenoid valve F Fuse page 18 Contactor coils Circular heating element Oven motorised ventilator Tangential motorised ventilator Capacitor Oven lighting lamp Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD 26 The Warranty Your appliance is covered by warranty The seller will replace or repair and his decision will be final free of charge for the customer only those parts that are defective
29. y of cooking cooking times are reduced the surface of the foods remains soft and does not form a crust there is little weight loss and the fatty mass is reduced Cooking with heart temperature function for prepared oven The temperature can be set inside the core of the food to be cooked using the special needle core probe that is supplied with the oven The probe must be pushed into the centre of the food in the thickest part avoiding the bones Place the food inside the cooking chamber and pull out the thermal probe lead and close the oven door The probe plug must be plugged into the special socket e Cooking with the parameter time set from 01 minutes to 9 hours and 59 minutes If during the cooking cycle the thermal probe should go to failure cooking is still being set for the time e Cooking with the parameter time set as INF If during the cooking cycle the thermal probe should go to failure cooking stops permanently page 12 Electric Ovens rev 1 EKF 423 D UD EKF 443 D UD EKF 311 D UD EKF 364 D UD EKF 411 D UD EKF 464 D UD EKF 411 D AL UD EKF 464 D AL UD e Cooking with some set phases and core probe connected Selecting the parameter time the display shows alternatively the time set for the active phase and the world Prb confirms that in a phase of the cooking cycle is set the parameter core temperature e Cooking with some set phases and core probe disconnected Selecting the parameter time
Download Pdf Manuals
Related Search