CX-1X1000 - KY Model
Contents
1. 8 1 3 Switch to the next menu and save the cahnge Dial gain switch for one time between AVCS and normal mode can save the parameters set in previous menu and enter into next menu at the same time 8 1 4 LED indicator in Programming Mode Red and Blue flash slowly together switch to a new menu items the number of flashes is the sequence number In menu item 1 2 7 the number of flashes indicates the parameter of current item In item 3 4 5 6 fast Red flashes indicate parameter value increasing fast Blue flash indicates value decreasing Number of red and blue flash Description of parameter and condition synchronously Red 1 flash 1520us 71Hz analog servo Red 2 flashes 1520us 250Hz digital servo 1 flash Servo type Red 3 flashes 1520us 333Hz digital servo Red 4 flashes 760us 400Hz digital servo Red 5 Flashes 960us 333Hz digital servo Seine Gyro Compensa Long Red 1 flash positive direction eae tion Direction Long Blue 1 flash reverse direction 3 flashes Servo centered 4 flashes Limit A of servo Servo goes to the limit position of direction A 5 flashes Limit B of servo Servo goes to the limit position of direction B Compensation of Servo centered move the pitch stick up and down to pitch to tail check the value and direction of compensation 6 flashes Parameter group Red 1 flash parameter group 1 is selected F3C mode Z flashes selection Red 2 flashes parameter group 2 is2. Cek CX 1X1000 1 Introduction Thank you for purchasing the CopterX CX 1X1000 Mini Heading hold Gyro CX 1X1000 is an AVCS gyro with small volume light weight and advanced performance Its high speed processor can process the signal with high frequency and control the tail accurately It can be easily programmed by a transmit or a program box sold separately it can work well with both electric and nitro R C helicopters 2 specification Dimensions 22 2 22 2 11mm Weight 11g metal case cables and plugs included Operating Voltage DC3 5V 10V Operating Current Drain 60ma Operating Temperature 10 50 Maximal Angular Velocity 800 sec Servo Compatibility 1520us analog servo 1520us digital servo 760us digital servo 960us digital servo Radio Compatibility PPM PCM 2 4G Black Red Orange Tailservo Corte Black Red Red Gexooo g a A Rudder Black Red White on Gain brown t E Pitch optional 4 LED Indication Steady Red Gyro is in AVCS mode Steady Blue Gyro is in normal mode Steady Red and Blue Gyro is waiting for receiver s signal Blue and Red LED are flashing synchronously Gyro is initializing keep the gyro steady rudder stick centered Red LED is flashing Gyro is in firmware update mode J Gyro Mounting The gyro should mount to a steady platform which is perpendicular to the main shaft and far away from the engine and other electric devices Mount the gyro t
3. ll the channels to be zero and make sure all the mixing functions related to tail turn off Set up a gain switch in transmitter which is used to control gyro s working mode AVCS mode and normal mode The relationship of the gyro actual gain and the displayed value in some popular transmitters are in the table as follows We recommend that you can set the gyro actual gain to be about 40 and then adjust the gain during practical flight The gain should be raised until the tail begins to oscillate quickly also called Tail Wag Once this point has been achieved reduce the gain a little and do a testOfly again Check and set the gain for each flight mode Teron aves mode Futaba gyromena se _ Futaba napon wow _ R Spekrumgyronem ox sw vow RT sperrom Endpoint oa e __ 100 _ 8 1 Set parameters by using gain switch and rudder stick of transmitter 8 1 1 Entering Programming Mode Power on transmitter and dial the switch to AVCS mode connect the gyro to receiver before selecting the servo type disconnect the gyro to servo move the rudder stick to any maximum extent position and remain it power on the gyro and the receiver after the gyro initialization red and blue LED indicator are off and then they flash alternately again it shows that gyro has entered Programming mode now center the rudder stick 8 1 2 Change parameter Change the parameters by moving rudder stick right or left in every item of menu
4. manual for more details When turn on the power the gyro needs several seconds to initialize During initialization Red and Blue LED flash synchronously When initialization is complete the tail servo will move right and then left to indicate If the airframe is not immobile or the rudder stick is moved during initialization the gyro may drift Remain the airframe immobile and the rudder stick centered then quickly dial the gain switch between Normal Mode and AVCS Mode for several times the gyro will initialize again to eliminate drift Before every flight verify that the mechanical frame and parts of helicopter is in good condition
5. o the platform by using a soft foam pad relax the cable of gyro to reduce transmission of vibrations through the cable Do not allow the gyro case to touch other parts of the helicopter Mounting on a small electric helicopter just use a 2 3mm foam pad p 2 3mm Foam Pad Gyro Mounting Platfoam Mounting on a large or a High vibration helicopters use a foam pad on each side of the damping shield plate 1 2 3mm Foam Pad O Damping and Shield Plate y _ 2 3mm Foam Pad Gyro Mounting Platfoam 6 Installation of Servo Horn and Linkage First of all make sure the mechanical parts of tail rotor install correctly all parts can move smoothly and the tail servo install firmly i 250 size 4 5mm 450 500size 7 5 10mm 600 or larger size 13 5 15mm 1 1 REEN Mount control ball to servo horn We recommend the distance from the ball to center is 4 5mm 250 size 7 5 10mm 450 500 size 13 5 15mm 600 or larger size Installthe horn to tail servo temporarily adjust the horn position to make it perpendicular to the linkage then set the tail pitch to be approximately 8 in the direction that compensates the main rotor torque by adjusting the linkage length Notice Don t connect the servo to the gyro until finishing the gyro type configuration 1 Transmitter Configuration Power on the transmitter and create a new helicopter model set the trims and subtrims of a
6. selected 3D mode Move rudder stick right and left quickly for several 8 flashes Data reset times until the Blue LED flashes fast then all the parameter is reset to the factory default settings NOTICE Factory default setting Before finishing the servo type selection don t connect the servo to the gyro Before finishing the item 3 of the menu don t fix the horn to the servo In Programming mode the gyro couldn t control the helicopter don t try to fly in Programming mode The menu is circular it goes back to the item 1 automatically after item 8 When you want to save the parameters you just setting you must dial the gain switch between AVCS and normal modes for one time at the same time it goes to next item of menu The item 6 is an optional function when it is set the tail control can be enhanced during the acute pitch changing in 3D flight For beginners we recommend setting it to default if it is set incorrectly please enter item 8 to reset the parameter to default If you want to use this function you need to setup a mixing from pitch channel to a vacant channel in transmitter and plug the gyro pitch signal wire to this vacant channel of receiver In the item 7 for beginner we recommend selecting parameter group 1 F3C mode After finishing the setup and saving the parameters you must turn off the power and restart the gyro to fly 8 2 Set parameters by using program box please check the program box user
Download Pdf Manuals
Related Search