User Manual Multi Lift
Contents
1. KH401 5 MULTI LIFT BATTERY CARE The batteries are fully sealed lead acid batteries which should be recharged on a regular basis To care for your batteries and obtain the maximum life DO NOT allow the batteries to run totally flat before recharging The controller is fitted with an audio low battery warning alarm When this warning alarm sounds complete the lift process then change the battery and recharge Kerry Equipment recommends that a 2 battery system be used this allows one battery to always be on charge while the other is in use and hence the hoist may never be out of service with a flat battery MAINTENANCE INSTRUCTIONS LUBRICATION The Hoist requires periodical lubrication These points are 1 CASTORS is always best practice to remove all hair and lint from the castors as soon as possible always allowing free movement of all the wheels The head bearing will need lubricating monthly Simply spray TAC 2 up into the bearing while rotating the castor fig 11 The wheel also requires lubricating every month To do this the wheel must be unbolted and removed from the castor frame TAC 2 can then be sprayed into the hub centre to lubricate the internal bearings fig 12 Fig 11 Fig 12 BASE PIVOT POINTS All pivot points will need to be lubricated monthly with TAC 2 or similar lubricant Simply spray the recommended points for 2 seconds on either side The hoist has to be turned onto its si2. 0 ________ 20 104 02 YOLYNLIY 1311 006 2 92 00 6 8 55 1570 ONY 3578 20 107 1 135 _____ 1198 1 13X2 VV 9 LNNOW pave 107007000 4015 1 10 5 2 00 2 7 3508 15 74 1 19097 1 _____________ wns YOLVALIV 1 100 12 090 28277 6 135 1108 NILY9 8 OWWHE X201 1 8 9 526 088195 0000000000 000 50020033508 0006 9 135 1108 10 40937 _ 0797 5 ____435 31070 1003 00 171 po 135 1108 5 z T3AIMS 133 109 566 40185006 PN 253 wan 1500 ILM9IIV 14 1 1 1 LOr HY MULTI LIFT KH401 SAFETY PRECAUTIONS For safety precautions only properly trained personal should use the hoist 1 2 1 The KH 401 Multi lift is manufactured and tested with safety and function for the carer and patients as the utmost importance No parts should be removed from the hoist without approval as this may create an unsafe working condition The MAXIMUM safe working load is 150 Kg s EMERGENCY LOWERING RA
3. should be checked with Kerry Equipment and or Distributor before commencing with any repair GENERAL CLEANING 1 hoist can be cleaned with low strength detergent warm water anda soft textured cloth This includes all Epoxy powder coated framework PVC cover polyurethane legs and yoke 2 CAUTION Do not immerse any parts in water Do not allow water cleaning liquid to enter the battery or controller Clean up spills immediately 3 SLING CARE Protect from direct sunlight Repair any cuts or fraying immediately Slings are machine washable Please refer to care instructions on the sling Supplied by Kerry Equipment AustiPty Ltd 994 4 Ralley Road Baleatta Perth Equi 111 Australia 8221 Telephone 67 89240 2344 or Facsimile 61 8924 1463 A Hills Company emalligkerryequipment com au Wit Kerry equipmient com au Manuf act ures of amp Home Equipment KH401 8 MULTI LIFT
4. ISING The emergency lowering raising buttons can be used to lower raise the hoist if there is a handset failure The switches are located on the controller under the big red emergency stop switch Simply press using a ballpoint pen or similar object DO NOT use a sharp object such as a compass point Always use the correct slings on the hoist The hoist should not be used on rough or sloping surfaces ie Wheel chair ramps etc and does not recommend that the hoist be used outdoors OPERATING INSTRUCTIONS INSTALLATION OF BATTERY PACK Before the Multi Lift Hoist can be operated the battery pack will need to be placed on charge See Charging Battery Instructions When the battery pack is fully charged remove the battery from the charger and place it on the hoist Simply locate the battery on the mounting bracket and clip the release lever into the secure position The Hoist is now ready for use fig 1 Fig 1 Fig 2 HANDSET RAISE LOWER The Hoist operates via a hand controller To raise or lower the hoist simply press the required switch on the touch pad There are four switches on the hand controller for raising and lowering The top two switches are for slow normal operation tortoise the middle two switches are for faster operation hare Simply choose the speed that suits your application fig 2 LEG GATING To OPEN or CLOSE the Gate on the legs simply press the hand controller with the required function
5. KH 401 MULTI LIFT OPERATING MAINTENANCE amp CLEANING MANUAL Kerry Equipment A Hills Company KEIM 011 INDEX PAGE SPECIFICATIONS 2 SPARE PART 3 SAFETY PRECAUTIONS 4 OPERATING INSTRUCTIONS 4 BATTERY CARE AND CHARGING 5 MAINTENANCE INSTRUCTIONS 6 ASSEMBLY DISASSEMBLY 8 CLEANING INSTRUCTIONS 8 SPECIFICATIONS DIMENSIONS Length 1100mm Width 670mm Height 1220mm Effective lift range 430mm 1700mm Leg gating inside 510mm 885mm Lift reach 700mm Base height 210mm Leg height from floor 160mm Turning radius 1300mm LIFT SPEED Slow 38mm per second LIFT DRY WEIGHT REMOVABLE BOOM REMOVABLE KNEEPAD LIFT CAPACITY CASTORS FINISH Fast 58mm per second 42 Kg with battery 4 75 9 4 40Kg Max load 150kg s 6150 Total lock rear polyurethane castor 100 Swivel front polyurethane castor Note Smaller castors available on request Epoxy powder coated Polyurethane legs and yoke PVC cover and upholstery kneepad ELECTRICAL ITEMS Tested by Linak Australia to standards KH401 AS 3108 1990 AS 3200 1 1990 2 MULTI LIFT 135 1108 LOAld 8 JIGNVH 3578 8 80MX 01 5 24088 60 90 107 50809 12 135 1109 1 0 4909002 92 1 ________ 05005 52 pa on 135 1109 10 2 eee __ _ ___ aa 784355 0V IINA
6. The lower set of switches operates the leg gate Open on the left close on the right KH401 4 MULTI LIFT 4 YOKE SLING MOUNTING POINTS fig 3 Refer to the fitting instructions supplied with your chosen sling fig 15 Fig 3 BATTERY CHARGING AND CARE 1 MOUNTING OF THE CHARGING UNIT is recommended that the charging unit be mounted on a wall out of the way of normal traffic at approximately waist high close to an electrical outlet This will help in easy attachment and removal of the battery when charging is required 2 CHARGING Before the Hoist can be operated the battery pack will need to be charged Minimum 4 hours for flat battery Please follow the instructions below 2 1 Plug the charger unit into the 240 Volt supply outlet The unit is now ready to accept a battery that requires charging a GREEN L E D ON will be displayed fig 10 2 2 charge the battery simply locate the battery on the mount bracket and clip into position The GREEN and ORANGE L E D on the front of the charger will be displayed The battery is fully charged when the ORANGE L E D is OFF and only the GREEN L E D 15 displayed 2 3 If atwo battery system is going to be used replace the first battery once charged with the second battery Charge as above NOTE A battery pack may remain on charge indefinitely without any detrimental effects to the battery or charging unit Fig 10 Charger unit without battery J
7. de for access to the following lubrication points To do this 2 people are required Follow the instruction below 2 1 Both people are to stand on one side of the hoist One near the push handle the other by the side of the hoist 2 2 The person near the push handle locks the total lock castors 2 3 In conjunction with one another pull the hoist towards the side lowering the hoist onto the floor You now have access to all the lubrication points under the base ie pivot points leg lever and leg pivot Simply spray TAC 2 on all the pivot points for 2 seconds KH401 6 MULTI LIFT 3 Leg Actuator Pivots fig 13 Leg Pivots Tie Rod Pivot Points Fig 13 4 ARM ACTUATOR and SPRING PIN LUBRICATION POINTS The arm pivot points will need to be lubricated monthly with TAC 2 or similar lubricant fig 14 Simply spray on each side of the recommended points as required The boom removable socket and spring button pin will also need lubricating as required 41 Arm Pivot Boom Socket Pin Actuator Pivots Arm pivot Boom spring button pin Actuator pivot Lower Actuator pivot Fig 14 TAC 2 is a CRC product and is available from most automotive outlets or from Kerry Equipment KH401 7 MULTI LIFT ASSEMBLY DISASSEMBLY INSTRUCTIONS Kerry Equipment fully assembles their hoist prior to delivery Kerry Equipment only recommends qualified service personal to work or service any of their hoists Any assembly or disassembly
Download Pdf Manuals
Related Search