PAR-4HUEX(UMX)
Contents
1. Disinfection gt Light p Light Guide Use a piece of clean gauze and brush to Put a little ethanol on a cotton Lightly wipe the light guide with disinfect the whole surface of handpiece swab Stick the swab into the a cotton swab with Ethanol for Disinfection Ethanol connection end of the handpiece 70 80 vol and lightly wipe the light guide Operation 2011 09 21 18 Sterilization Thermal washer disinfector LJ Handpieces with this symbol may be cleaned and disinfected with a thermal washer disinfector To use a thermal washer disinfector first read the operation instructions for the unit Strictly follow the instructions attached for cleaning mode and solution D Improper cleaning modes and solutions will damage the instrument D Follow the disinfector manufacturer s recommendations for cleaning solutions and methods for dental instruments Do not use strong acidic or alkaline solutions Thoroughly rinse off all cleaning solution Operation 2011 09 21 19 lt Lubrication gt Before autoclaving do not fail to lubricate and clean with AR spray Operation 2011 09 21 Sterilization 20 Sterilization AWARNING e Do not point the spray nozzle at anyone and do not use the spray near an open flame ANOTE e The handpiece will malfunction without regular AR spray maintenance e Never use any type of spray other than AR spray Other lubricants will cause the coupling O ring to swell and make it difficult to conn2. NK PAR 4HX O NK PAR 4HMX O NK only O ring prevent loosening of bod Q g P g y os O rings xd Body C QD 1 Take the handpiece off its main tube 2 Turn Body C in the illustration in the direction shown by the arrow and take it off Operation 2011 09 21 Replacement Parts and Storage 3 Take off the O rings with tweezers or some other suitable tool 4 Put on the new O rings Spray the O rings with AR Spray 6 Replace Body C CA A WARNING e Tighten Body C securely all the way Otherwise air could leak out and prevent a proper connection with the coupling 40 Replacement Parts and Storage Storage Storage Conditions Temperature 10 C 14 F 70 C 158 F Reletive Humidity 10 85 RH without condensation Atmospheric pressure 700 1 060 hPa Do not expose to direct sunlight frequently or for long times Store the handpiece in a clean dry place after autoclaving it Operation 2011 09 21 41 Maintenance and Inspection Maintenance and Inspection Regular Inspection Maintenance and inspection are generally consider to be the duty and obligation of the user but if for some reason the user is unable to carry out these duties he may rely on a qualified medical device serviceman Contact your local dealer or the J Morita Corp for details Replace the parts listed in the Parts Lists as necessary depending on degree of wear and length of use This instrument should
3. Sterilization ANOTE e Remove the bur or point before autoclaving e Do not touch the push button when operating the handpiece to remove excess spray This could damage the cap or the capsule cartridge e Instruments are extremely hot after autoclaving do not touch them until they cool off Operation 2011 09 21 30 Replacement Parts and Storage Replacement Parts and Storage Replacement Parts Replace the parts as necessary depending on degree of wear and length of use Order parts from your local dealer or the J Morita Corp Rotor Cartridge with O ring and screw Cap with O ring and screw PAR 4HUEX No 5011147 No 5011161 PAR 4HUMX No 5011148 00088 000 Operation 2011 09 21 31 Replacement Parts and Storage Cartridge lamp O ring exhaust seal No 5020550 No 5012320 PAR 4HUEX O WH PAR 4HUEX O WH PAR 4HUMX O WH PAR 4HUMX O WH O ring prevents loosening of body No 5012320 No 5811500 PAR 4HUEX O WH NK PAR 4HUEX O NK PAR 4HUMX O WH NK C gt PAR4HUMXONK O O O COO CD Operation 2011 09 21 32 Replacement Parts and Storage For Morita CP4 O WO CP4 LD W LD and CP5 O Coupling One way Spray Valve Coupling Gasket Coupling Wrench O ring Set No 5811837 CP4 No 5811838 No 5011831 No 5811835 CP5 No 7911823 rs Operation 2011 09 21 33 For Morita CP4 O WO Coupling Cartridge Lamp No 5011570 e dw T 4H Lamp Cover No 5811832 9 Lamp Cover O ring No 5
4. and Inspection 42 Sage xssssascresse EOM RN RESO ES ARE nene ranean 8 Troubieshootlng i edo ae lere re bac ere kd a ed 45 Inspecting and Sterilizing Before Use 8 POOF OCANOM ecc DE 46 Handpiece Attachment gt eeeessusss 9 Poor Spray Delivery eere 47 Inserting and Removing Burrs 12 Cannot insert burrs or points 49 Aller USE iEon scevest edet Ortes Ue ntud ee ES 16 Liglitdaoesn E WOEK Loops pestes a ven rav debate tees 51 SteriliZallori sx eti sd uisu edo M s dui 17 Technical Description eeeeeeeeeeee 52 Replacement Parts and Storage 31 SDOGIII Cata o eld Uu M LU ire 52 Rotor Cartridge Replacement 35 CP4 O WO CP4 LD W LD CP5 O Coupling 60 Cartridge Lamp or LED Replacement 36 O rings Replacement ccccccsesseccsseeesseeeesseees 40 Operation 2011 09 21 Prevent Accidents Prevent Accidents Introduction Thank you for purchasing a TWINPOWER TURBINE 4H handpiece This instrument is designed for dental treatment such as grinding drilling and polishing teeth For optimum safety and performance read this manual thoroughly before using the unit and pay close attention to the warnings and notes Keep this manual at hand for rea
5. and the chuck Operation 2011 09 21 Usage lt Removal gt Hold the push button down and pull the burr straight out 12 Yes Operation 2011 09 21 No Usage 13 Operation 2011 09 21 Usage ANOTE e Crown removal and other similar operations produce considerable vibration and can cause the bur to get stuck in the handpiece Avoid this by frequently removing and reinserting the bur e In case of abnormal noise or vibration during use replace the bur If this eliminates the problem the bur was defective If this does not solve the problem the handpiece needs to be repaired e After long usage wear on bearings results in greater noise Operation 2011 09 21 15 After Use Disconnect the handpiece from the tube and remove the point or burr Burrs and points may get stuck in the handpiece if they are left in for too long Always remove the burr or point after finishing treatment Operation 2011 09 21 Usage 16 Sterilization Sterilization lt Cleaning gt Clean debris off the attachment with a brush and running water Clean the spray holes with the wire provided if they get plugged up with cutting debris or impurities in the water After cleaning dry it off with air from the threeway syringe or some other method and then wipe it with a piece of gauze dampened with Ethanol for Disinfection Ethanol 70 80 vol Spray hole Wire Syringe Nozzle Operation 2011 09 21 17 Sterilization lt
6. be inspected every 3 months in accordance with the following maintenance and inspection items Operation 2011 09 21 42 Maintenance and Inspection Inspection Items m Chuck Gripping Strength Use the Chuck Tester to check the chuck s gripping strength Replace the capsule cartridge if the chuck has lost its gripping strength m Cap Tightness Make sure that the cap and the cap screw are tightened properly m Rotation and Water Make sure the handpiece operates smoothly and emits a stream of water For repairs contact your local dealer or the J Morita Corp Parts List m Rotor Cartridge Regularly Required Replacement Parts m Cap Operation 2011 09 21 43 Maintenance and Inspection Disposal of Medical Devices Any medical devices which could possibly be contaminated must be first decontaminated by the responsible doctor or medical institution and then be disposed of by an agent licensed and qualified to handle medical and industrial waste Service and Other Contacts For repair or other types of service contact your local dealer or the J Morita Office Operation 2011 09 21 44 Troubleshooting Troubleshooting If the instrument does not seem to be working properly the user should first try to inspect and adjust it himself If the user is unable to inspect the instrument himself or if the instrument fails to work properly after being adjusted or after parts are replaced contact your local dealer or the J Morita Cor
7. connection make sure the tube connector is clean and free of debris e The light will lose its brightness if the end of the fiber optic cable is scratched or otherwise damaged by being dropped for instance e Air or water may leak if the coupling is not tightened up enough Operation 2011 09 21 64 CP4 O WO CP4 LD W LD CP5 O Coupling Cleaning Wipe the outside cover with Ethanol for Disinfection Ethanol 70 80 vol ANOTE e Coupling must NOT be autoclaved or cleaned ultrasonically e The coupling could be damaged if it is soaked in Ethanol for Disinfection Ethanol 70 80 vol or cleaned with a strong corrosive solution e Clean both ends of the light guide if the light seems to have lost its brightness Operation 2011 09 21 65 CP4 O WO CP4 LD W LD CP5 O Coupling Spray Adjustment CP4 WO CP4 W LD Indicator Turning the dial in the direction indicated by the arrow in the illustration will gradually reduce the amount of spray and then reach 0 For maximum spray turn the dial until the W matches up with the indicator See illustration Spray Control Dial Tube Ring Operation 2011 09 21 66 CP4 O WO CP4 LD W LD CP5 O Coupling ANOTE e f the coupling is not securely tightened up with the wrench water or air could leak Operation 2011 09 21 67 CP4 O WO CP4 LD W LD CP5 O Coupling Replacement lt Coupling O ring Replacement gt O rings Replace the o rings if air or water starts
8. leaking from the connection After replacement take the nozzle off the AR spray can and lightly apply a little oil on the new o rings AWARNING e Do not fail to replace all the o rings otherwise air pressure cold cause the tube to suddenly disconnect and this could injure the patient Operation 2011 09 21 68 CP4 O WO CP4 LD W LD CP5 O Coupling One way Spray Valve Replacement Inspecting One way Valve Cutting debris and other foreign matter could be sucked into the water tube if the one way valve is not working properly Inspect it once a month 1 Remove the needle from a plastic syringe and fit the end over the spray pipe 2 Check that there are no gaps between it and the gasket 3 Pull the plunger out a little and then release it If the plunger moves back in the valve is OK 4 Replace the valve if the plunger does not go back in at all Gasket Water Pipe Operation 2011 09 21 69 CP4 O WO CP4 LD W LD CP5 O Coupling Replacement One way Valve E 1 Use a needle or similar object to remove the gasket 2 Remove the old valve and replace it with a new one 3 Replace the gasket in its original position Gasket ANNOTE e Do not damage the part of the gasket that bunches up against the water pipe as it is required to make an effective seal Operation 2011 09 21 70 EU Authorized Representative under the European Directive 93 42 EEC MEDICAL TECHNOLOGY PROMEDT CONSULTING GMBH Alt
9. 811833 Operation 2011 09 21 For Morita CP4 LD W LD Coupling LED No 5011575 Replacement Parts and Storage p P O O ring No 5811833 LED Cover No 5011025 34 Replacement Parts and Storage Rotor Cartridge Replacement Replace the Rotor Cartridge if worn ball bearings result in poor or irregular rotation if burrs are difficult to insert or remove or if the chuck loses it gripping power The Rotor Cartridge and its O ring wears out and must be replaced periodically The bearings and other parts wear out and make more noise after a certain period of time When replacing the rotor cartridge follow the instructions that come with the new cartridge AWARNING e f used in this condition a burr or point could come out inside the oral cavity and injure the patient or be swallowed ANNOTE e Do not fail to use the Rotor Cartridge for the PAR AHUEX and the PAR 4HUMX Operation 2011 09 21 35 Replacement Parts and Storage Cartridge Lamp or LED Replacement For Morita PAR 4HUEX O PAR 4HUMX O KaVo PAR 4HUEX O KV PAR 4HUMX O KV SIRONA PAR AHUEX O SR PAR 4HUMX O SR and NSK PAR 4HUEX O NK PAR A4HUMX O NK lamp or LED replacement refer to the user s manual for the couplings of it s maker A WARNING e Turn off the power switch to avoid the risk of burns and electrical shock e The lamp and its cover are quite hot immediately after the lamp has burned out Avoid burning yourself do not touc
10. High Speed Air Turbine Handpiece TWINPOWER TURBINE 4H cs m lt with light gt PAR 4HUEX O PAR 4HUEX O KV WH SR NK PAR 4HUMX O PAR 4HUMX O KV WH SR NK Operation Instructions Manufactured by J MORITA MFG CORP This manual covers the TWINPOWER TURBINE 4H series handpieces which can be connected to Morita couplings CP4 O CP4 WO CP4 LD CP4 W LD or CP5 O and other manufacturer s couplings PAR 4HUEX O PAR 4HUEX O KV WH SR NK PAR 4HUMX O PAR 4HUMX O KV WH SR NK Morita CP4 O CP4 WO CP4 LD CP4 W LD and CP5 O coupling KaVo MULTIflex and MULTIflex LUX coupling KaVo MULTIflex and MULTIflex LUX are registered trademarks for Kaltenbach amp Voigt GmbH 3 W amp H Roto Quick coupling W amp H and Roto Quick are registered trademarks for W amp H Dentalwerk BUrmoos GmbH SIRONA R F coupling Sirona is a registered trademark for Sirona Dental Systems GmbH NSK Mach Phatelus FlexiQuick coupling Mach Phatelus and FlexiQuick are registered trademark for NSK NAKANISHI INC Notice Of Protect Intellectual Property CN PAT 03123631 6 DE PAT 10060152 US PAT 5902108 3897953 CN PAT 031236324 DE PAT 10320902 JP PAT 3208345 4088475 DE PAT 19807566 US PAT 6676374 JP PAT 3672781 4122174 DE PAT 19860953 US PAT 7048540 JP PAT 3795722 4160319 CONTENTS Prevent Accidents cuui eoe cere a 1 SOJE sai ee ee 41 Parts Identification and Accessories 5 Maintenance
11. ces with this symbol may Serial Number Autecinvabi to 135 C be cleaned and disinfected with a The first character of the serial number e m thermal washer disinfector specifies the year of manufacture as follows Y 2010 Z 2011 Operation 2011 09 21 58 Operation Instructions ual Manufacturer Authorized representative in the European Community Operation 2011 09 21 Technical Description 59 CP4 O WO CP4 LD W LD CP5 O Coupling CP4 O WO CP4 LD W LD CP5 O Coupling CP4 O with light CP4 WO with light and spray control CP4 LD with LED light gt CP4 W LD with LED light and spray control Coupling Before use check the following items Water Spray Air Does the connection end of the tube match the coupling Lamp voltage is correct Exhaust This coupling cannot be connected to a tube that does not Drive Air have light capability Electrical Contacts ANNOTE e The CP4 light will burn out more quickly if voltage is greater than the value specified if it uses a long fade out time or if the chair applies and cuts off the voltage suddenly Operation 2011 09 21 60 CP4 O WO CP4 LD W LD CP5 O Coupling CP4 O CP4 WO CP4 LD CP4 W LD Model CP4 O with halogen lamp light Model CP4 LD with LED light CP4 WO with halogen lamp light and Spray Control CP4 W LD with LED light and Spray Control ISO 9168 Type 3 C Coupling ISO 9168 Type 3 C Coupling Weight 2 t 10g Weight 2 t 10g Lamp Voltag
12. dy reference Caution Federal law restricts this device to sale by or on the order of a dentist for U S A Safety Precautions The instrument must be used in accordance with the instructions in this manual Read this manual thoroughly prior to operating or maintaining the instrument Operation 2011 09 21 1 Prevent Accidents The following symbols and expressions indicate the degree of danger and harm that could result from ignoring the instructions they accompany A WARNING This warns the user of the possibility of extremely serious injury or complete destruction of the instrument as well as other property damage including the possibility of fire ANOTE This warns the user of the possibility of mild injury or damage to the instrument D Usage Note This alerts the user of important points concerning operation or the risk of equipment damage The user i e clinic hospital etc is responsible for the management maintenance and use of medical devices This instrument must not be used by anyone except legally qualified dentists and oral surgeons practitioners This instrument must not be used for any other than the intended purpose as specified in this manual Operation 2011 09 21 2 Prevent Accidents Disclaimer m The J Morita Mfg Corp will not be responsible for accidents equipment damage or bodily injury resulting from 1 repairs made by personnel not authorized by the J Morita Mfg Corp 2 any changes modi
13. e Max 3 3 V 0 05 V D C for coupling contacts Input Voltage AC DC 3 3 V 0 05 V Recommended Lamp Power Max 2 4 W AC 2 5 10 V DC 2 5 15 V for coupling contacts Input Current Max 0 30 A 0 2 A at 3 3 V DC Lamp power supply must conform to IEC60601 1 and voltage is SELV special safe low voltage Input power supply must conform to IEC60601 1 Reinforced insulation Double insulation Operation 2011 09 21 61 CP4 O WO CP4 LD W LD CP5 O Coupling CP5 O with Fiber Optic Coupling Before use check the following items Does the connection end of the tube match the coupling Water Spray Air This coupling cannot be connected to a tube that does not have light capability This coupling cannot be connected to a 4 hole tube Exhaust Drive Air CP5 O Model CP5 O with Fiber Optic Fiber Optic ISO 9168 Type 2 B Coupling Weight 2 t 10g Lamp power supply must conform to IEC60601 1 and voltage is SELV special safe low voltage Operation 2011 09 21 62 CP4 O WO CP4 LD W LD CP5 O Coupling Connect Coupling Before first using the coupling or if the handpiece coupling connection gets stiff take the nozzle off the AR spray can and lightly spray the coupling s o rings Line up the projections on the coupling with the indentations Tighten securely with the wrench provided in the tube and then tighten up the cover nut Operation 2011 09 21 63 CP4 O WO CP4 LD W LD CP5 O Coupling ANOTE e Before
14. e cartridge and cap And make sure the cartridge is the correct one Operation 2011 09 21 Troubleshooting 49 Cover the head with a piece of gauze insert the nozzle into the chuck and spray for 2 seconds Operation 2011 09 21 Troubleshooting Connect the handpiece and run it for 15 seconds to blow out excess spray Then wipe it clean with a piece of gauze 50 Light doesn t work Lamp or LED may be burned out No Check tube and chair Yes Replace lamp or LED Operation 2011 09 21 Troubleshooting 51 Technical Description Specification Name Type Head Height mm Head Diameter mm Speed Number of Spray Nozzles Weight g Operation 2011 09 21 Technical Description Specifications may be changed without notice due to improvements TWINPOWER TURBINE 4H PAR 4HUEX O PAR 4HUMX O 12 7 10 6 Q9 3 0 000 30 000rpm 3 1 CPA CP5 51 KV 57 WH 51 SR 50 NK 48 52 Air amp Water Pressure at handpiece connection Air Recommended 0 23 0 25 MPa Range 0 2 0 29 MPa Water 0 05 0 2 MPa Tip Air 0 2 minimum MPa Exhaust Air 0 03 maximum MPa Air Flow at 0 2 MPa 35 3 NL min Chuck Push Chuck Bearing Ball Bearing O Drive air should be clean and dry Operation 2011 09 21 Technical Description 53 Technical Description ANOTE e Excessive air pressure could damage the turbine s performance Operation 2011 09 21 It could also result in an inju
15. ect and disconnect Also it could make it take longer to stop in an emergency Operation 2011 09 21 21 Sterilization There are different spray nozzles for each type of coupling Look at the side of the nozzle to check this Make sure you use the right one Look here coupling mark No Mark Morita couplings CP4 O CP4 WO CP4 LD CP4 W LD and CP5 O PAR 4HUEX O PAR 4HUMX O KV C KaVo coupling PAR 4HUEX O KV PAR 4HUMX O KV WH W amp H coupling PAR AHUEX O WH PAR AHUMX O WH SR SIRONA coupling PAR AHUEX O SR PAR AHUM X O SR NK NSK coupling PAR 4HUEX O NK PAR 4HUMX O NK Operation 2011 09 21 22 Operation 2011 09 21 Sterilization Shake AR spray can 2 or 3 times before using it Raise the lever on the nozzle assembly and swivel the chuck nozzle down into position Cover the head with gauze insert the nozzle and spray for 2 seconds Push the nozzle lever down Insert the nozzle into the handpiece connection end and spray for 2 seconds 23 Sterilization Operation 2011 09 21 24 Sterilization lt Connect gt lt Operate gt lt Disconnect gt Connect the handpiece to its tube Operate the handpiece for about Disconnect the handpiece 15 seconds to blow out excess lubricant Operation 2011 09 21 25 Sterilization lt Check Chuck s Gripping Power gt Carefully insert the chuck tester as Firmly hold down the push button Carefully pull on the tester until the far as
16. enhofstraRe 80 66386 St Ingbert Germany TEL 49 6894 581020 FAX 49 6894 581021 The authority granted to the authorized representative MEDICAL TECHNOLOGY PROMEDT Consulting GmbH by J Morita Mfg Corp is solely limited to the work of the authorized representative with the requirements of the European Directive 93 42 EEC for product registration and incident report ul J MORITA MFG CORP 680 Higashihama Minami cho Fushimi ku Kyoto 612 8533 Japan http www jmorita mfg com Distributors J MORITA CORPORATION Tokyo Office 2 11 15 Ueno Taito ku Tokyo 110 8513 Japan Osaka Office 3 33 18 Tarumi cho Suita Osaka 564 8650 Japan J MORITA USA Inc 9 Mason Irvine CA 92618 U S A TEL 1 949 581 9600 FAX 1 949 465 1095 J MORITA EUROPE GMBH Justus Von Liebig Strasse 27A D 63128 Dietzenbach Germany TEL 49 6074 836 0 FAX 49 6074 836 299 SIAMDENT CO LTD 444 Olympia Thai Tower 3rd Floor Ratchadapisek Road Samsennok Huay Kwang Bangkok 10310 Thailand TEL 66 2 512 6049 FAX 66 2 512 6099 http www siamdent com J MORITA CORPORATION Australia and New Zealand Suite 2 05 Aero 247 Coward Street Mascot NSW 2020 Australia TEL 61 2 9667 3555 FAX 61 2 9667 3577 MORITA GLOBAL WEBSITE __http www morita com PUB H5087 E 1 Printed in Japan
17. fications or alterations of its products 3 the use of products or equipment made by other manufacturers except for those procured by the J Morita Mfg Corp 4 maintenance or repairs using parts or components other than those specified by the J Morita Mfg Corp and other than in their original condition 5 operating the equipment in ways other than the operating procedures described in this manual or resulting from the safety precautions and warnings in this manual not being observed 6 workplace conditions and environment or installation conditions which do not conform to those stated in this manual such as improper electrical power supply 7 fires earthquakes floods lightning natural disasters or acts of God Operation 2011 09 21 3 Prevent Accidents m The J Morita Mfg Corp will supply replacement parts and be able to repair the product for a period of 10 years after the manufacture of the product has been discontinued m Warranty is honored only when a claim is accompanied by the warranty agreement with purchase date product name and model serial number inscribed on the body of the product and name of the distributor Operation 2011 09 21 Parts Identification and Accessories Parts Identification and Accessories Parts Identification Cap Cap Screw Light Guide only light models 2 Guide OBody Handpiece Connection Push Button Head Connection end differs for various models Notch Spray Hole Opera
18. h these parts ANNOTE e Do not leave fingerprints or any foreign substances on the new lamp These could cause the lamp to break as soon as it is turned on which could cause an injury If necessary use Ethanol for Disinfection Ethanol 70 80 vol to clean the lamp Operation 2011 09 21 36 For W amp H PAR 4HEX O WH PAR 4HMX O WH Body C Disconnect the handpiece from the main tube Turn off the lamp and rotate body C in the direction shown in the illustration Operation 2011 09 21 Replacement Parts and Storage O ring Exhaust seal O ring Keeps body tight Take out the old lamp with tweezers 37 GOOD Operation 2011 09 21 Socket Rim BAD Replacement Parts and Storage Install the lamp so that the rim does not go in too far ANOTE e f the rim goes into the socket the connection could be defective or the lamp could come out 38 Screw body C back into its original place Reconnect the handpiece and operate it to make sure the lamp lights up Operation 2011 09 21 Replacement Parts and Storage A WARNING e Make sure Body C is screwed all the way down If the handpiece is not properly connected to the tube air pressure could cause the tube to blow off which could cause an injury ANNOTE e Use only cartridge lamps made specifically for this model Order lamp cartridges from your local dealer or the J Morita office 39 O rings Replacement PAR 4HEX O
19. it will go and push the tester all the way blue line appears in then release the button Operation 2011 09 21 26 If the blue line appears the chuck is OK Blue Line Stop pulling if the blue line appears and let the tester slowly go back to its original position Hold the push button down firmly and take the tester out of the chuck Operation 2011 09 21 Sterilization If the Blue Line Does NOT Appear Chuck has lost gripping power D Clean the chuck with AR spray and test it again If the chuck still fails the test replace the capsule cartridge 27 Operation 2011 09 21 Sterilization 28 Sterilization lt Packaging and Sterilization gt Wipe the handpiece with a piece of gauze dampened with Ethanol for Disinfection Ethanol 70 80 vol and put it in a Sterilization pouch Recommended Autoclaving Conditions In a sterilization pouch at least 5 minutes at 134 C 273 2 F Minimum drying time after sterilization 10 minutes D Do not sterilize in any way except autoclave Do not fail to clean and lubricate the instrument before autoclaving it Autoclaving and drying temperatures must not exceed 135 C 275 F After autoclaving take the instrument out of the autoclave as soon as it cools off A WARNING e To prevent the spread of serious life threatening infections such as HIV and hepatitis B the handpiece must be autoclaved after the completion of each patient Operation 2011 09 21 29
20. p Operation 2011 09 21 45 Troubleshooting Poor Rotation Lubricate with AR spray And then disconnect handpiece and step on foot pedal Does air come out of the end of the tube with enough force No Defective tube Contact serviceman Yes If other handpieces work OK replace the capsule cartridge Make sure the capsule is the correct one Operation 2011 09 21 46 Troubleshooting Poor Spray Delivery Disconnect handpiece Check coupling connection Step on foot pedal Does air comes out of the end of the tube with enough force i No Defective tube or water lines inside chair Yes Replace the coupling s o ring Or clean spray hole refer to next page for cleaning i Make sure the O rings on the capsule cartridge are properly installed If this does not solve the problem contact your local dealer or the J Morita Corp Operation 2011 09 21 AT How to clean spray hole Spray hole Wire Use the wire provided to clean out the spray hole Operation 2011 09 21 Troubleshooting Syringe Nozzle After cleaning blow the hole out with a syringe and wipe the handpiece with gauze dampened with Ethanol for Disinfection Ethanol 70 80 vol 48 Cannot insert burrs or points Check that burrs and points are OK No Use only burrs and points that are suitable and in good shape Yes Lubricate with AR spray refer to next page for lubrication i If this does not solve the problem replace the capsul
21. ry 54 Technical Description Usable Burrs and Points Type PAR 4HUEX O PAR 4HUMX O Shank Diameter 01 59 1 60 mm ISO standard Tip Diameter 2 0 mm maximum Total Length 22 mm maximum 20 mm maximum Shank Length 10 mm minimum 7 5 mm minimum Use only burrs and points that conform to ISO1791 1 standards Shale Genet 4 Tip Diameter eo e Shank Diameter ISO standard Total Length Operation 2011 09 21 55 Operation 2011 09 21 Technical Description 56 Technical Description ANOTE e Always use burrs and points with clean shanks dirty shanks cause the chuck to wear out more quickly and lose its gripping power e Always carefully remove all cleaning fluids before inserting a burr into the chuck some cleaning fluids are corrosive and if a burr or point with cleaning fluid on it is inserted the chuck could be ruined e f a dirty burr or one with cleaning fluid on it has been inserted by mistake contact your local dealer or the J Morita Office to have the instrument inspected e Carefully read the instruction manual of the burr maker e Use only burrs made of a single piece of metal do not use burrs whose head is welded to the shank e Welded joints break easily Operation 2011 09 21 of Technical Description Terminology and Symbols CE 0197 marking Conforms to European medical Ball Bearing Type Name device Directive 93 42 EEC Manufacturer Requires AR Lubrication Handpie
22. t PAR AHUEX O PAR AHUMX O For Morita CP4 O CP4 WO CP4 LD CP4 W LD and CP5 O coupling lt Connect gt lt Disconnect gt Hold the tube and slide the handpiece on until it clicks securely into place Pull the coupling slightly towards the tube and then pull the handpiece off Handle the handpiece carefully Do not drop the handpiece or bang it against the chair etc This could degrade its performance or break the light guide Make sure the coupling connection is clean and free of dust and other debris otherwise the handpiece could be damaged Operation 2011 09 21 9 Usage Except for Morita CP4 O CP4 WO CP4 LD CP4 W LD or CP5 O coupling refer to the user s manual for the model you have PAR 4HUEX O KV PAR 4HUMX O KV_ KaVo MULTIflex and MULTIflex LUX coupling PAR 4HUEX O WH PAR 4HUMX O WH W amp H Roto Quick coupling PAR 4HUEX O SR PAR 4HUMX O SR SIRONA R coupling PAR 4HUEX O NK PAR AHUMX O NK NSK MachLite Phatelus coupling Operation 2011 09 21 10 Usage For information on assembling the CP4 O WO CP4 LD W LD and CP5 O Coupling refer to the page 60 Operation 2011 09 21 11 Inserting and Removing Burrs lt Insert gt Push Button i l f Insert the burr carefully straight in Hold down the push button firmly and Do not force the burr in without holding push the burr all the way in then down the push button this will damage the release the push button burr
23. tion 2011 09 21 5 Parts Identification and Accessories Accessories Chuck Tester yellow green Spray Hole Wire Code No 5010695 Code No 5250940 PAR 4HUEX Code No 5010840 PAR A4HUMX if O disinfect with ethanol autoclavable Tools which are the same as those for other models may be labelled as for those models Accessories differ slightly if the handpiece is purchased separately Operation 2011 09 21 6 Parts Identification and Accessories AR Spray 4H Spray Nozzle No 5010212 or No 5010307 No 5010293 lt No 5010295 No 5010216 PAR 4HUEX O PAR 4HUEX O KV PAR 4HUEX O WH PAR 4HUEX O SR PAR 4HUEX O NK PAR AHUMX O PAR 4HUMX O KV 2 PAR 4HUMX O WH 2 PAR 4HUMX O SR PAR 4HUMX O NK No 5010297 No 5010299 N ON A t UN o i N NN M N 7 NCC Wb 7 disinfect with ethanol Operation 2011 09 21 Usage Usage Operating Conditions Temperature 10 C 50 F 40 C 104 F Relative Humidity 30 75 Atmospheric pressure 700 1 060 hPa Inspecting and Sterilizing Before Use The handpiece is not sterilized before shipping It must be autoclaved before being used for the first time Make sure that the cap and cap screw are tightened properly and that there is no gap between the head and the cap If you discover any problem with the above items do not use the handpiece but have it repaired instead Operation 2011 09 21 8 Usage lt Handpiece Attachment g
Download Pdf Manuals
Related Search
PAR 4HUEX(UMX)