(NX-8V2) User Manual
Contents
1. 2011 UTC Fire amp Security All rights reserved NX 8V2 USER S MANUAL INX8V20M Rev B June 20112. 13 14 15 16 17 18 19 20 21 22 23 24 T interlogix be A UTC Fire amp Security Company NetvvorX NX 8V2 LED Keypad User Manual POWER Light is on when AC READY Light is on when the SERVICE Light is on to NX 8V2 SYST E M povver is present flashes to system is ready to arm flashes indicate a trouble condition indicate a low battery condition if ready to force arm with your system KEY P A D Includes models NX 108E NX 116E NX 124E ARMED Light is on when armed off when disarmed flashes to indicate a previous alarm INSTANT Light is on when there is no entry exit delay FIRE Light is on to indicate fir alarm flashes to indicate a trouble condition with your fire system NUMERIC CODE ENTRY KEYS PULL OUT ZONE ID TAB ZONE LIGHTS are on steady t indicate bypass slow flash for zone fault rapid flash for service condition 5 FUNCTION KEYS perform EMERGENCY ACTIVATION KEYS various functions NOTE Some of the features described above may or may not be available for your system Check with your installation company to find out how your system is programmed SECURITY SYSTEM NOTES Installing Service Company For Service Call Central Station Duress Code FUNCTION CODES Function Code Controls Function This system 15 1 isnotQ partitioned EMERGENCY ACTIVATION KEYS check if enabled Q Fire
3. 9 6 Enter the Master Code Enter the Day of Week 1 Sunday 3 Tuesday 5 Thursday 7 Saturday 2 Monday 4 Wednesday 6 Friday Enter the Month Code Must always be two 2 digits 01 January 05 May 09 September 02 February 06 June 10 October 03 March 07 July 11 November 04 April 08 August 12 December Enter the Day Code Must always be two 2 digits Example The 5 would be entered as 0 5 Enter the last two digits of the Year Code Example For 2007 enter 0 7 SETTING THE SYSTEM CLOCK Step 1 Step 2 Step 3 Press p 9 7 Enter the Master Code Enter the hour code which must be two 2 digits Note The clock is a 24 hour clock Refer to the following table on page 15 13 Step 4 Enter the minutes code which must be two 2 digits Example 7 minutes after would be entered 0 7 14 Time Hour Code Time Hour Code Time Hour Code ees 00 08 4 00 PM 16 1 00 AM 01 09 5 00 PM 17 2 00 AM 02 10 6 00 PM 18 3 00 AM 03 11 7 00 PM 19 4 00 AM 04 12 8 00 PM 20 5 00 AM 05 13 9 00 PM 21 6 00 AM 06 14 10 00 PM 22 7 00 AM 07 15 11 00 PM 23 KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad If programmed your system keypad may sound for any of the following reasons Beeps for all keypresses Sounds a continuous tone during the Entry delay time Pulses when a day z
4. NOTE For partitioned systems someone changing the code of another person must have access to all or more partitions than the user being changed The ready light will flash Enter the 2 digit user number You must always enter 2 digits such as 0 3 for user 3 or 5 2 for user 52 Enter the new four 4 or six 6 digit user code NOTE To delete a user code enter p p p p for a 4 digit code or p p p p p p for a 6 digit code The ready light will flash indicating you are back at Step 4 above If the code is rejected the sounder will beep 3 times If another user code needs to be programmed return to Step 5 Press the key while the ready light is flashing to exit the User Code Programming Mode ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below Assign user codes before assigning authority levels Step 1 Step 2 Step 3 Step 4 Step 5 Press p 6 Enter a Master Arm Disarm Code NOTE Someone changing the authority of another person can only add or remove partition authorization for partitions to which they have access The ready light will flash Enter the 2 digit user number to be assigned authority The ready light is constant and the instant light will flash Lights illuminated indicate the authority levels assigned to this code An explanation of the lights is listed below You may toggle
5. STAY is used when the user is inside the premise and wants protection around the perimeter Listed below are the steps to arm in the STAY Mode Step 1 Close all protected doors and windows e Ready light must be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is not on or flashing If the power light is off you have no AC power Restore power if possible If not contact your installing company listed on page 1 of this booklet for service Step 2 Enter your 4 or 6 digit user code If Auto Bypass is enabled all interior zones will be bypassed if you do not leave through a designated entry exit door If Auto Bypass is enabled omit Step 3 e When Auto Instant is enabled if you do not leave through a designated entry exit door the instant light will illuminate indicating that the entry exit doors no longer have an entry delay If Auto Instant is enabled omit Step 4 Step 3 Press the STAY key e The stay light will illuminate indicating that all interior zones are bypassed All interior devices will bypass automatically giving the user freedom of movement within the interior area e The bypass light will illuminate if any zone s are bypassed If any zone s have been bypassed previously by the user the light s corresponding
6. as programmed by the installing company User Code A four 4 or six 6 digit entry used to arm or disarm the system UNDERSTANDING THE LIGHTS Armed Light The armed light is on when the system is armed The armed light is off when it is disarmed The armed light will flash when there has been an alarm during the previous arm cycle Bypass Light The bypass light is on when any zone in this keypad s partition is bypassed The zone s that is bypassed will also be illuminated If the bypass light is off no zones are bypassed Cancel Light The cancel light will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication process Note The abort feature must be enabled Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report Note The cancel feature must be enabled No additional keypad tones will be emitted Chime Light The chime light is on when the chime feature is on off otherwise Exit Light The exit light is on during the exit delay During the last 10 seconds of the exit delay the exit light will flash rapidly and the keypads will beep rapidly as a warning to the user that the exit time is about to expire The use
7. 4 8 until you have assigned authority levels to all user numbers Press the key to exit the Assigning Authority Level Program 11 OTHER KEYPAD FUNCTIONS SETTING THE KEYPAD TONE Step 1 Press p 0 Keypad is now in the Adjust Tone mode Step 2 Pressing the 1 key will make the keypad sounder go to higher tones pressing the 2 key will make the keypad sounder go to lower tones Step 3 When the desired tone is reached press the key to set this tone and exit from the Adjust Tone mode CHANGE PARTITION Optional Step 1 Press p 1 Step 2 Press a NUMBER key between 1 and 8 to change partitions momentarily Step 3 If no other key is pressed it will go back to its standard partition in ten seconds Step 4 If another key is pressed the system will remain in the new partition until no keys have been pressed for 60 seconds VIEW ALARM MEMORY Step 1 Press p 3 The zone s that created the last alarm will be displayed on the keypad Step 2 The ALARM MEMORY feature will flash those zones that created alarms and will light steady those zones that were bypassed during the last alarm TEST FUNCTION Optional If programmed this function will perform a battery test communicator test and or a siren test No alarms will be sent and no reports will be sent unless a communicator test is performed at which time a test signal will be sent Step 1 Press p 4 The test will be performed as
8. Q Auxiliary Emergency Q Police PROGRAMMED FUNCTIONS Q Abort Delay 6 Q Cancel Alarm Q Forced Arming o Q Auto Bypass o Q Change Partitions Q Group Bypass o Q Auto Instant Q Chime Q Quick Arm 6 Q Battery Test Communicator Test Q Re Exit Q Siren Test o These features should not be enabled on UL listed systems ENTRY EXIT DELAY TIMES Exit Delay Time Secondary Exit Delay Time Entry Delay Time Secondary Entry Delay Time ZONE DESCRIPTIONS 01 09 17 02 10 18 03 11 19 04 12 20 05 13 21 06 14 22 07 15 23 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY THIS BOOKLET SHOULD BE KEPT IN AN ACCESSIBLE LOCATION FOR THE LIFE OF THE SECURITY SYSTEM IF YOU DO NOT UNDERSTAND ANY PART OF THIS MANUAL YOU SHOULD NOTIFY YOUR INSTALLING COMPANY The SECURITY CONTROL can be turned on ARMED and off DISARMED by entering a 4 or 6 digit code into the Keypad Control which is similar to a telephone keypad If your Security Control has been so programmed you may be able to turn on ARM your System by simply pressing the STAY or EXIT key The system must always be disarmed using a 4 or 6 digit code The LED keypad includes up to 35 lig
9. When you enter the protected area through one of the designated Entry Exit doors the keypad control will sound a continuous tone for the duration of the entry delay time or until you enter a valid code The red armed light will go off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay an alarm will occur NOTE If the red armed light is flashing during the entry delay the alarm system has been activated in your absence Leave the building immediately and call your alarm company and or the police from a safe location 8 CANCEL ABORT FEATURE Optional see page 1 The cancel light will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication process Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report No additional keypad tones will be emitted BYPASSING ZONES If you wish to bypass one or more zones this must be done while the system is in the disarmed state The following steps are used for bypassing zones Step 1 Press the BYPASS key Step 2 Enter user code if required optional The bypass light flashes Step 3 Enter the digits indicating the zone you wish to bypass Example Press the
10. the battery is connected and adequately charged Care should be taken to plug in and restrain the A C Transformer after testing PLEASE READ THE FOLLOWING INFORMATION AND INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR SECURITY CONTROL SYSTEM IF YOU DO NOT UNDERSTAND ANY PORTION OF THIS MANUAL OR IF YOU HAVE ANY QUESTIONS ABOUT YOUR SYSTEM CONTACT THE INSTALLING COMPANY LISTED ON PAGE 1 OF THIS BOOKLET TABLE OF CONTENTS GLOSSARY OF 9 55 4 UNDERSTANDING THE 46 5 5 5527 5 Armed Bt a 22222000 0000000000 5 Bypass Eights isa nl te a ner Andenne 5 Ganc l Eight 5 Chime e nl 5 EXIT G Mts E eet nm te aE ent SUD AZRB 5 Fire Light s s g minier ait tnt TR nt A ie den 5 Instant Light i Wate SARAYLAR rat 5 POWER LION R ENEE ent Men Arr tres di Ne NE 5 le Vie ue 6 Stay ENG UE 6 ZOMG MGM Er nr 0020200000 6 EMERGENCY ACTIVATION KEYS 552 6 KEYPAD 1 9 5 5 5 727 7 Arming Your System In The Away Mode 522 7 Arming Your System In The Stay Mode 7 Using The Quick Arm iii 8 Disarming The 5 51 8 Cancel Abort Feature A 9 Bypassing Zones ss 9 Group BYPASS si manne rarase tinaaa 9 Unbyp
11. to the 1 of 8 service lights 6N TELEPHONE FAULT Press the 6 key The zone light s that is illuminated corresponds to the system fault s below 6 Line Trouble Line Cut This light will illuminate when there is telephone line trouble or the telephone line has been cut The service light will remain lit until the telephone trouble clears and a user code is entered 7 Auxiliary Comm Device Fail Radio backup has failed 7N FAILURE TO COMMUNICATE This light will illuminate when there is a failure to communicate between your system and the central station 8N LOSS OF SYSTEM TIME This light will illuminate when there has been a loss of power and your system clock needs to be reset Instructions are on page 13 EXIT Press the key to exit the Service Light mode N Note This fault is global in nature and will affect all partitions of a multi partition system 16 EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition For example the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building Draw up a floor plan of your home Show windows doors stairs and rooftops that can be used for escape Indicate each occupant s escape routes Always keep these routes free from obstruction Determine two means of escape from each room On
12. to the bypassed zone s will illuminate alerting the user that a zone s may be unprotected and can be faulted without an alarm Step 4 To toggle from a delayed entry mode to an Instant mode press the STAY key again e The instant light will illuminate indicating that the entry exit doors have no entry delay USING THE QUICK ARM Optional see page 1 The Quick Arm feature may be used if it is enabled Quick Arm will allow the user to arm the security system in the AWAY mode by pressing the EXIT key or arm in the STAY mode by pressing the STAY key The keypads beep during the exit delay beeps rapidly for the last 10 seconds of the exit delay and beeps 1 second at the end of the exit delay This feature is used for ARMING ONLY and will not disarm the security system This is ideal for a maid or baby sitter code etc CHANGING MODES WHILE SYSTEM IS ARMED Pressing the STAY key will turn on off toggle a delay on entry exit doors and turn on off toggle the instant light Optional Press the BYPASS key at this time to turn on off toggle all designated interior zones Optional When armed pressing the EXIT key will start the exit delay enabling you to leave the building IMPORTANT The instant light needs to be off at this time if you plan on re entering the building otherwise you will create an alarm You may restore an entry delay by pressing the STAY key again DISARMING THE SYSTEM
13. turn on off the authority level by pressing the number for that authority level 10 Step 6 Step 7 Step 8 Step 9 LIGHT AUTHORITY LEVELS IF LIGHT 8 IS OFF 1 Reserved Note Do not change if on Arm Only Arm Only After Closing Time Master Arm Disarm can program other codes Arm Disarm Bypass Zones Oo amp 09 PO Open Close Reporting If this light is on this code is programmed as a 8 function code Do not change Press to exit Press the p key The ready light will flash This moves you to the partition enable The user has access in partitions that are illuminated The illuminated numbers indicate each partition where the user has access To change any of the partitions where the user has access press numbers corresponding to areas where you want to give the user access or deny access Example If zone light 2 is lit then the user is assigned access to partition 2 By pressing the 2 key the light will go off denying access to partition 2 Refer to chart shown below LIGHT PARTITIONS ASSIGNED 1 Partition 1 Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8 INIO AOIN When the partitions are assigned press the p key This returns you to Step 3 previously mentioned At this point you may enter another user number to assign authority level Repeat Steps
14. 1 key for zone 1 press 1 2 for zone 12 Step 4 Press the BYPASS key again Step 5 corresponding zone light will illuminate indicating the zone has been bypassed Repeat steps 3 and 4 for any other zone s that need to be bypassed Step 6 Press the BYPASS key again or press the key to exit the Bypass Mode The bypass light will stop flashing upon exiting the Bypass Mode GROUP BYPASS By pressing the BYPASS key followed by the 0 key then the BYPASS key again all zones that are designated as group bypass zones will be bypassed Press the BYPASS key again to exit group bypassing UNBYPASSING To manually unbypass zones perform the bypassing procedure on a zone that is already bypassed The corresponding light for that zone will go off when unbypassed NOTE All zones will automatically be unbypassed each time the system is disarmed TURNING THE DOOR CHIME ON AND OFF The door chime is turned on or off by pressing the CHIME key while the system is in the disarmed state If the chime is on the chime light will be illuminated If the chime is off the chime light will be off Each press of the CHIME key will toggle the chime feature on off and produce a momentary ding dong sound CHANGING USER CODES Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Your system must be in the Disarmed state to change user codes Press p 5 Enter a Master Arm Disarm Code
15. asSing isa nine Mir ne rl ieee aes 9 Turning The Door Chime On And Off 9 CHANGING USER 5 72 10 ASSIGNING USER CODE AUTHORITY 10 OTHER KEYPAD FUNCTIONS 7 7 12 Setting The Keypad Tone 12 Change Partition 5 222 ane nan L m ee 12 View Alarm Memory ui 12 Test upper ebe Se ech dee HAT era Bee 12 VValkeTeste c aaa La d iis devi Mat inner l 12 Reset Tute EE 13 Set System Datei Saint se at hatin een 13 Setting The System Clock 13 KEYPAD CONTROL TONES BEEPS ss 15 SERVICE MENU geess ats ee cate eee A a o ils te 16 EMERGENCY EVACUATION 5 5 7272 17 GLOSSARY OF TERMS Abort Delay An option that allows a delay in reporting to the central station There is a communicator delay of 30 seconds It can be removed or increased up to 45 seconds at the option of the end user by consulting with the installer Authority Level The level of access an individual has when using an alarm panel Central Station Location where alarm data is sent during an alarm report Chime Feature An option that allows the keypad to sound a ding dong whenever an entry exit door is opened Codes Can be either User Codes relating to a person or Function Codes a toggle switch to turn specific functions on off NOTE A system may have eithe
16. e will be the normal exit from the building The other may be a window that opens easily An escape ladder may have to be located near the window if there is a long drop to the ground below Set a meeting place outdoors for a headcount of the building occupants Practice escape procedures In a home sleep with bedroom door closed this will increase your escape time If you suspect fire test the door for heat If you think it is safe brace your shoulder against the door and open it cautiously Be ready to slam the door if smoke or heat rush in Practice escaping to the outdoors and meeting in an assigned spot Call the Fire Department from a neighbor s phone NOTE After the installation of your Security System has been completed notify your local Fire and Police Departments to give them your name and address for their records Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms This equipment should be installed in accordance with the National Fire Protection Association s Standard 72 For additional information write the National Fire Protection Association Batterymarch Park Quincy MA 02269 The following are examples of evacuation plans A plan unique to your home or business should be drawn and memorized by each occupant KITCHEN BEDROOM Le DINING BEDROOM BEDROOM LIVING ROOM E FIRST FLOOR SECOND FLOOR EH 3 ECO FRONT s 17 SYSTEM NOTES
17. he 2 key to determine the service condition One or more zone lights will illuminate indicating what service s is required Call your service provider immediately for these problems Below is a listing of what each light means in a service condition LIGHT 1 PROBLEM SYSTEM FAULT Press the 1 key The zone light s that is illuminated corresponds to the system fault s below 1 Over Current Fault 5 Expander Low Battery 2 Siren Trouble 6 Expander Box Tamper 3 Box Tamper 7 Expander Trouble 4 Expander Power 8 Ground Fault Note Faults 1 amp 2 are global in nature and will affect all partitions of a multi partition system Press the key to return to the 1 of 8 service lights ZONE TAMPER Press the 2 key and the zone light s will illuminate showing the zone s that are tampered Press the key to return to the 1 of 8 service lights ZONE LOW BATTERY Press the 3 key The zone light s will illuminate showing which zone s has a low battery This only applies to wireless zones Press the key to return to the 1 of 8 service lights ZONE LOSS OF SUPERVISION Press the 4 key and the zone light s will illuminate showing which zone s has loss of supervision This only applies to wireless zones Press key to return to the 1 of 8 service lights ZONE TROUBLE Press the 5 key and the zone light s will illuminate showing which zone s has a trouble condition Press the key to return
18. hts and a built in electronic sounder These provide specific information relating to the status of the security system which is described in the booklet Understanding what the lights and sounds mean will help you to easily operate your system READ THE ENTIRE MANUAL AND IF POSSIBLE PRACTICE ON THE KEYPAD CONTROL WHILE YOUR PROFESSIONAL INSTALLER IS ON SITE KEEP IN MIND THE LEVEL OF SECURITY YOU WILL OBTAIN WITH THIS SYSTEM RELATES SPECIFICALLY WITH TWO MAJOR FACTORS 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system YOU SHOULD BE AWARE OF THE FOLLOWING FACTS WHEN PREPARING A SAFETY SECURITY PLAN FOR YOUR HOME BUSINESS Your security system is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security Your system should be tested weekly Your system will not work without power Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event Smoke and heat detectors may not detect heat and smoke in all situations Use qualified security professionals to install and maintain your security system t may be possible to arm the security system without the backup battery connected Your periodic test should be done with A C Power removed to verify
19. one is violated while the system is disarmed Pulses when a FIRE zone has a trouble condition Beeps 3 times for trying to arm with the Ready light off if Force Arming has not been selected Beeps for 1 second or emits a ding dong sound for the Chime feature Beeps during an exit delay beeps rapidly for the last 10 seconds of an exit delay and beeps 1 second at the end of the exit delay Pulses when the armed status changes and the AC power is off Pulses when the armed status changes and any zone s are bypassed Pulses when the armed status changes and a low battery is detected Pulses when the armed status changes and a Tamper condition is detected Beeps to indicate Telephone Line Cut if selected Pulses when one or more of the following conditions are detected Zone or Box Tamper Low Battery AC Power Fail or Expander trouble Beeps 3 times every minute indicating a low battery or missing transmitter is detected if wireless device is in system Entering code will suppress the sounder for 12 hours Entering a valid code will silence the keypad sounder when it is pulsing The arm disarm state of your system will not change when entering a code to silence a pulsing keypad sounder Please contact your installer if a trouble condition exists 15 SERVICE MENU The service light will be on if the security system requires service If the service light is on press the p key followed by t
20. programmed Step 2 the siren test is performed enter a user code to silence the siren WALK TEST If enabled it will permit a temporary walk through test where all zones become silent and do not report alarms to the central station Step 1 Press p Chime user code During this test the chime light will flash on the LED keypad 12 Step 2 Step 3 Step 4 Each time a zone is faulted the zone light on the LED keypad will illuminate and the chime will sound The number of the faulted zone s will be displayed on the LCD keypad It will also be entered into alarm memory and the internal log The keypad will begin to beep after 15 minutes in this mode This beeping indicates that the VValk Test mode will be automatically exited in 5 minutes To exit at any time during this mode enter a user code Otherwise the AWalk Test Mode will automatically exit after 20 minutes RESET FUNCTION This function is used to reset Smoke Detectors Zone Troubles and Zone Tampers Step 1 Disarm the system if not disarmed Step 2 Press p 7 Resets have now been performed Step 3 If the keypad begins beeping the reset did not execute properly Enter your code to silence the keypad Wait a few minutes and repeat step 2 to attempt another reset If the keypad still beeps after repeated attempts please contact your installer SET SYSTEM DATE Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Press the p
21. r 99 four 4 digit codes or 66 six 6 digit codes but not a mixture of the two Duress Code An option that allows a special code to be sent to the central station that indicates the alarm system is being operated under duress Any arming or disarming operation performed using the Duress PIN in lieu of the User PIN will operate normally without additional audible or visual indicators Forced Arming An option that allows the system to be turned on ARMED with one or more zones open A system that is ready to be force armed will flash the ready light Note Those zones that are not ready will not create an alarm Function Code A Function Code is either a four 4 or six 6 digit code that has been programmed by the installer to operate a device Group Bypass An option that allows the user to bypass multiple zones with a single operation Instant Delay An option that allows an instant alarm condition for Entry Exit doors or grants a delay to allow someone to enter exit the building without an alarm or before entering a user code to disarm Master Code A master arm disarm code that can program other user codes Partitioned System A system divided into multiple areas in which its own user or users control each area Perimeter The outer edge of the protected area Quick Arm An option that allows you to turn on ARM the security system by pressing either the STAY or EXIT key on the keypad control for ARMING only
22. r may want to disarm the system if the exit light is flashing in order to prevent an alarm The user may then re arm the system and exit before the delay expires Fire Light A steady fire light means a fire zone has been faulted A rapidly flashing fire light means that a fire zone is in a trouble condition Instant Light The instant light is on when there is no delay on your entry exit door s Any time the instant light is on and the exit delay has expired the opening of an entry exit door will produce an immediate alarm The instant light can be toggled on or off by pressing the Stay key while the system is armed When the instant light is off the entry exit door s is delayed Power Light The power light is on if the primary power is on The power light will flash if the system has a low battery condition Ready Light The ready light is on when the system is ready to arm and flashes if ready to force arm The ready light is off when the system is not ready to arm because of a zone s being faulted Stay Light The stay light is on when the all interior motion detector zones are bypassed Zone Light The zone lights are off when everything is normal A zone light will be on if the zone has been bypassed If a zone light is flashing that zone is in alarm or has been faulted If a zone light is flashing rapidly it means that the zone is in a trouble condition Tro
23. uble conditions are Tamper s Hardware Low Battery Loss of Supervision A combination of Alarm Fault and Tamper Trouble will produce a rapid flashing light for a short period of time followed by a slow flashing light EMERGENCY ACTIVATION KEYS e Fire Auxiliary Emergency Police NOTES You must hold these keys for 2 seconds to activate these functions Your system may not be programmed for these activation keys see page 1 You should press these keys only in an emergency situation that requires response by emergency personnel If your system is programmed for these functions the following reports can be sent Fire Key This key can activate the fire alarm when pressed for 2 seconds If your system is connected to a monitoring center an emergency report could be sent to that center The keypads sound a continuous beeping Auxiliary Emergency Key This key can activate the auxiliary alarm when pressed for 2 seconds If your system is connected to a monitoring center an emergency report could be sent to that center The keypads sound a continuous beeping Police Panic Hold Up Key This key can sound a local audible alarm when pressed for 2 seconds If your system is connected to a monitoring center an emergency report could be transmitted to that center NOTE Some Panic Hold Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center Check with yo
24. ur installing company to determine how your security system will respond to the Panic Hold Up activation If programmed for Silent Hold up the keypads will not sound Otherwise the keypads will sound a continuous beeping KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE AWAY MODE AWAY is used when the user is away from the premise and wants the interior protected Listed below are the steps to arm in the AWAY Mode Step 1 Close all protected doors and windows e Ready light will be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is not on or flashing e If the power light is off you have no AC power Restore power if possible If not contact your installing company listed on page 1 of this booklet for service Step2 Enter your 4 or 6 digit user code to arm the system e The armed and exit lights will illuminate e You may now leave the building Note The keypads beep slowly during an exit delay During the last 10 seconds of the exit delay the keypads beep rapidly and the exit light will flash rapidly as a warning to the user that the exit time is about to expire At the end of the exit delay the keypads beep one longer tone 1 second The user may wish to disarm and re arm the system if more time is needed ARMING YOUR SYSTEM IN THE STAY MODE
Download Pdf Manuals
Related Search