Ethan Frome - E-acumulatori.ro
Contents
1. TEMPERATURE STATION The Temperature Station comes complete with a detachable stand that gives the option of table standing or wall mounting To wall mount 1 Fix a screw into the desired wall leaving the IRL head extended out by about 5mm Hy p 2 Using the Temperature Station s hanging hole carefully hang it onto the screw Note Always make sure that the unit locks onto the screw head before releasing 75 POSITIONING THE OUTDOOR TRANSMITTER f The Transmitter is supplied with a holder that may be attached to a wall with the two screws supplied The Transmitter can also be placed on a flat surface by securing the stand of the Transmitter 76 To wall mount 1 Secure the bracket onto the desired wall REIN using the screws and plastic anchors 2 Clip the remote temperature sensor onto the bracket 77 Note Before securing in place please ensure that the Temperature Station can receive the 868MHz signal from the temperature transmitter at the positions that you wish to place them In event that the signal is not received relocate the transmitters or move them slightly as this may help the signal reception CARE AND MAINTENANCE e Avoid placing the units in areas prone to vibration and shock as these may cause damage 78 Avoid areas where the units can be exposed to sudden changes in temperature i e direct sunlight extreme cold and wet moist conditions as thes2. the essential requirements of R amp TTE Directive 1999 5 EC 85
3. 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION Congratulations on purchasing this innovative 868MHz Temperature Station which displays time indoor temperature and up to three outdoor temperature readings To enjoy the full benefits of this innovative product please read this operating manual 44 Instant Transmission is the up and coming state of the art new wireless transmission technology exclusively designed and developed by LA CROSSE TECHNOLOGY T offers you an immediate update of all your outdoor data measured from the transmitters follow your climatic variations in real time ITE x INSTANT TAANSMISSION TEMPERATURE STATION 2 Hanging hole Battery compartment SET CH key Eus ine Perey key J Detachable 46 stand TEMPERATURE TRANSMITTER MN S 47 FEATURES LCD clock in 12 or 24 hour time display Indoor and outdoor temperature reading in degrees Celsius or Fahrenheit Can receive up to three Outdoor transmitters Indoor and outdoor temperature with Minimum and Maximum records Wireless transmission at 868 MHz Signal reception intervals at 4 seconds Table standing or wall mountable detachable table stand 48 SETTING UP WHEN ONE TRANSMITTER IS USED T 2 First insert the batteries in the transmitter see How to install and replace batteries in the Temperature transmitter below Within 2 minutes of po
4. ces Disposal of electronic waste in wild country and or in unauthorized grounds strongly damages the environment Please contact your local or and regional authorities to retrieve the addresses of legal dumping grounds with selective collection 82 All electronic instruments must from now on be recycled User shall take an active part in the reuse recycling and recovery of the electrical and electronic waste The unrestricted disposal of electronic waste may do harm on public health and the quality of environment As stated on the gift box and labeled on the product reading the User manual is highly recommended for the benefit of the user This product must however not be thrown in general rubbish collection points 83 The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any consequences that occur should an inaccurate reading take place This product is designed for use in the home only as indication of the temperature This product is not to be used for medical purposes or for public information The specifications of this product may change without prior notice This product is not a toy Keep out of the reach of children No part of this manual may be reproduced without written authorization of the manufacturer 84 gt R amp TTE Directive 1999 5 EC Summary of the Declaration of Conformity We hereby declare that this wireless transmission device does comply with
5. e will lead to rapid changes in temperature which reduces the accuracy of readings When cleaning the LCD and casing use a soft damp cloth only Do not use solvents or scouring agents Do not submerge the units into water Immediately remove all low powered batteries to avoid leakage and damage Replace only with new batteries of the recommended size 79 e Do not make any repairs to the units Please return them to the original point of purchase for repair by a qualified engineer Opening and tampering with the units may invalidate its guarantee SPECIFICATIONS Temperature measuring range Indoor 9 9 C to 59 9 C with 0 1 C resolution 14 1 F to 139 8 F with 0 2 F resolution displayed if outside this range Outdoor 39 9 C to 59 9 C with 0 1 C resolution 39 8 F to 139 8 F with with 0 2 F resolution displayed if outside this range 80 Temperature checking intervals Indoor Every 15 seconds Outdoor Every 4 seconds Distance transmission up to 100 meters Open space and free from interference Power source Temperature Station 2x AAA IEC LR3 1 5V batteries Transmitter 2 x AA IEC LR6 1 5V batteries Battery life for both units i Approximately 12 months Alkaline batteries recommended 81 Dimensions L x W x Temperature Station 58x 23x 125 mm Transmitter 38 2 x 21 2 x 128 3 LIABILITY DISCLAIMER The electrical and electronic wastes contain hazardous substan
6. lowing the setup procedures This is because a random security code is assigned by the transmitter at start up and this code must be received and stored by the Temperature Station in the first 3 minutes after power supplying BATTERIES REPLACEMENT amp MAINTENANCE For best performance batteries in all units should be replaced at least once every 2 years to maintain optimum running accuracy Ensure that the batteries used are new of from the correct size 58 Please help in the preservation of the environment and return used batteries to an authorized depot 59 LCD SCREEN The Temperature Station s LCD is split into 3 sections and once the batteries are inserted all the segments will light up momentarily before displaying 1 Time 0 00 2 Indoor and outdoor temperature in degree Celsius C or Fahrenheit 60 TIME 09 INDOOR E Indoor Temperature T 5 or F OUTDOOR Outdoor Temperature In in C or F IL Outdoor Transmitter B 2 identification No En e 61 When the signal is successfully received by the Temperature Station the outdoor transmission icon will be switched on If not successful the icon will not be shown on LCD So the user can easily see whether the last reception was successful icon on or not icon off On the other hand the short blinking of the icon shows that a reception is currently taking place 12 or 24 hour setting After the batterie
7. nsmitter then see Checking 868 MHz reception below MINIMUM AND MAXIMUM OUTDOOR TEMPERATURE READING Outdoor sign Minimum 0 6008 Maximum icon PD icon E amp 69 By pressing the MIN MAX key the current indoor and outdoor temperature will alternate between the minimum maximum and current temperature recordings The time when the minimum and maximum outdoor temperature records were received will be also shown on the LCD blinking Once a new outdoor temperature high or low is reached it will automatically be set into the Temperature Station s memory RESETTING THE MINIMUM AND MAXIMUM READINGS User may reset the minimum and maximum temperature data to the current value by the following step Press and hold the MIN MAX key for about 3 seconds to reset all the minimum maximum data of all channels and the indoor sensor to the 70 current values in a single action OUTDOOR TEMPERATURE CHANNEL 1 2 AND 3 If more than one transmitter is used and to alternate between the temperature readings of transmitter 1 2 and 3 simply press the SET CH key If the reading is from transmitter 1 then the identification number 1 will be displayed in the outdoor temperature section of the LCD The same will apply to the next transmitter and so on However if only one transmitter is used no identification number will be displayed on the LCD 71 CHECKING FOR 868 MHz RECEPTION In normal sur
8. pressing the SET CH key to advance to the minute mode Again using the MIN MAX key to set the minutes of the current time and then finally followed by pressing the SET CH key to exit the setting mode Your Temperature Station is now fully operational 65 USING THE TEMPERATURE STATION INDOOR TEMPERATURE The indoor temperature is displayed on the second line of the LCD under the time The Temperature Station s built in sensor automatically measures the temperature once the batteries are inserted 66 MINIMUM AND MAXIMUM INDOOR TEMPERATURE RECORDINGS oom Indoor sign TNbooR Minimum INDOOR Maximum 67 By pressing the MIN MAX key the current indoor and outdoor temperature will alternate between the minimum maximum and current temperature recordings also changes for outdoor temperature Once a new indoor temperature high or low is reached it will automatically set into the Temperature Station s memory OUTDOOR TEMPERATURE READING The outdoor temperature reading is displayed on the bottom line of the LCD under the indoor temperature The Temperature Station receives the outdoor temperature via 868 MHz frequency if the batteries are inserted into the transmitter within the 2 1 2 minutes of the setting up time See Setting up above 68 Note Should the outdoor temperature not be received within 2 minutes after inserting the batteries into a tra
9. roundings for example away from interfering sources such as TV sets the outdoor temperature can usually be easily received within 2 1 2 minutes If the outdoor temperature is not displayed on the LCD after 2 1 2 minutes then check the following 1 The distance of the units should be at least 1 5 2 0 meters away from interfering sources such as computer monitors or TV sets 2 Avoid placing the units onto or in the immediate proximity of metal doors window frames or structures 72 Using other electrical products such as headphones and speakers that operate on the same signal 868 MHz can prevent the transmission pick up Neighbours using electrical products operating on the 868 MHz signal can also cause interference In most severe cases the reception is only possible once all other electrical products using the 868 MHz are switched off Within thick concrete rooms such as basements and tower blocks the 868 MHz signal can be weakened avoid placing near metal frames and structures Transmission can be affected by exposure to extreme temperature conditions For example if the weather has been extremely cold 73 under 25 C for an extended period of time then the transmission signal may be weakened Please bears this in mind when positioning the transmitter Note If the outdoor temperature is still not received by the Temperature Station after checking the above list all units should be reset 74 POSITIONING
10. s are inserted set the time display as follow 1 Press and hold the SET CH key for about 3 seconds to enter the set mode 62 2 Either a 12h or 24h will appear on the LCD If 12h is displayed then the current time display is set to 12 hour time If 24h is displayed then the current time is set to 24 hour time 3 To alternate between the two times display mode simply press the MIN MAX key 4 When the desired time display is selected press the SET CH key once more to enter the Celsius or Fahrenheit degree setting mode Note When the time display is set to 12 hour mode the temperature unit will be fixed to F when the selected time mode is 24 hour the temperature unit will be fixed to C 63 CELSIUS OR FAHRENHEIT DEGREE SETTING Following from the 12 or 24 hour setting mode 1 Either a C or F will appear on the LCD If C is displayed then the current temperature reading is set to Celsius If F is displayed then the current temperature reading is set to Fahrenheit 2 To alternate between the two temperature reading modes simply press the MIN MAX key 3 Press SET CH key to confirm and enter the time setting mode TIME SETTING Following from the Celsius or Fahrenheit degree mode 64 The Hour digit in the time section starts flashing Using the MIN MAX key to set the hours of the current time and then followed by
11. ser shall restart the setting up from step 1 Note User shall insert the batteries into the third transmitter within 45 53 seconds after the Temperature Station displays the information of the second transmitter 8 In order to ensure sufficient 868 MHz transmission however the distance between the Temperature Station and the transmitter should not be more than 100 meters see notes on Positioning and 868 MHz Reception 54 HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION The Temperature Station uses 2 x AAA IEC LR3 1 5V batteries When batteries will need to be replaced the low battery icon will appear on the LCD To install and replace the batteries please follow the steps below 55 e Lift up the battery compartment cover Insert batteries observing the correct polarity see marking Replace compartment cover 56 HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER The Temperature transmitter uses 2 x AA IEC LR6 1 5V batteries When batteries will need to be replaced the low battery icon will appear on the LCD of the Temperature Station To install and replace the batteries please follow the steps below 1 1 Remove the battery cover 2 Insert the batteries observing the correct polarity see marking 3 Replace the battery cover on the unit 57 Note In the event of changing batteries in any of the units all units need to be reset by fol
12. the indoor temperature and the time as 0 00 will be displayed If these informations are not displayed on the LCD after 60 seconds remove the batteries from both units and wait for at least 60 seconds before reinserting them The outdoor temperature from the first transmitter channel 1 51 should then be displayed on the Temperature Station Also the signal reception icon will be displayed If this does not happen after 2 minutes the batteries will need to be removed from both units and reset from step 1 5 Insert the batteries in the second transmitter as soon as the outdoor temperature reading from the first transmitter are displayed on the Temperature Station Note User shall insert the batteries into the second transmitter within 45 seconds after the Temperature Station displays the information of the first transmitter 52 6 The outdoor temperature from the second transmitter and the channel 2 icon should then be displayed on the Temperature Station If this does not happen after 2 minutes the batteries will need to be removed from all the units and reset from step 1 T Insert the batteries in the third transmitter as soon as the channel 2 icon and outdoor data are displayed on the Temperature Station Then within 2 minutes the channel 3 outdoor data from the third transmitter will be displayed and the channel icon will shift back to 1 once the third transmitter is successfully received If this is not happen u
13. wering up the transmitter insert the batteries in the Temperature Station see How to install and replace batteries in the Temperature station below Once the batteries are in place all segments of the LCD will light up briefly Following the indoor temperature and the time as 0 00 will be displayed If these informations are not displayed on the LCD after 60 seconds remove the batteries and wait for at least 60 49 seconds before reinserting them Once the indoor data is displayed user may proceed to the next step After the batteries are inserted the Temperature Station will start receiving data signal from the transmitter The outdoor temperature should then be displayed on the Temperature station If this does not happen after 2 minutes the batteries will need to be removed from both units and reset from step 1 In order to ensure sufficient 868 MHz transmission however the distance between the Temperature Station and the transmitter should not be more than 100 meters see notes on Positioning and 868 MHz Reception 50 WHEN MORE THAN ONE TRANSMITTER IS USED 1 2 3 User shall remove all the batteries from the Temperatuire Station and transmitters and wait 60 seconds Insert the batteries in the first transmitter Within 2 minutes of powering up the first transmitter insert the batteries in the Temperature Station Once the batteries are in place all segments of the LCD will light up briefly Following
Download Pdf Manuals
Related Search