User manual
Contents
1. Y r IE a 4 wo a as l Un AL HUIA H il Bema i TRANBERG Tranberg AS PO Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fax 47 51 57 89 50 E mail info tranberg com www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com2. TEF 99 70 LED HELIDECK FLOODLIGHT LIGHT USER MANUAL IMPORTANT Read this instruction carefully before installing the product 10 12 2015 TRANBERG Tranberg AS P O Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fax 47 51 57 89 50 E mail info tranberg com www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com TUM 4605 REV C TEF 9970 LED HELIDECK FLOODLIGHT USER MANUAL INTRODUCTION TOOLS REQUIRED Thank you for purchasing this product Regular tools required for installation For installation maintenance and assurance of a long life F Tools for mounting e g 13 mm wrench to fasten the of this product please follow this manual mounting bracket to the deck and adjust the angle of the lamp e 3 mm hexagon key Unbraco Allen key for mounting APPLICATIONS the lock to the termination compartment and to loosen the screws for the terminal assembly if necessary e Floodlight on helideck general Floodlighting e 32mm wrench to disassemble the blind plug and as e Zone 1 Zone 2 and safe area semble the cable gland CONTENT IN BOX The product is fully assembled and ready for installation APPROVALS IECEx ATEX CERTIFIED x II 2 G Ex d e op is IIB H T4 Gb T5 version available SAFETY PRECAUTIONS Warning DO NOT OPEN WHEN ENERGIZED Accordin
3. aintenance tasks to this product The equipment is ready for installation when leaving the production facilities of Tranberg AS Check the condition of the equipment and the contents when unpacking Any dam age done to the equipment during transportation is not the responsibility of Tranberg AS If the content is not complete file a claim to the manufacturer immediately The TEF 9970 is delivered with several mounting options A mounting bracket for flat surfaces is standard For the light output to be in accordance with any regulations listed in this document the helideck floodlight must be mounted on a horizontal surface coincident with the helideck The luminaire must always be installed in an upright posi tion Any other mounting positions should not be used for permanent installation without a confirmation from Tran berg s technical department If the luminaire is mounted on a vessel or a floating installation movements such as roll and pitch which moves the luminaire out of its original up right position is not taken into account Mounting Details Field Connections Floodlight 1 Floodlight 2 m On Dim 50 Dim Off Full Light Owon a Dim L A N PE Dim L N PE TEF9970 TEF9971 TEF9970 TEF9971 When mounting the lid to
4. g to EN 60079 0 2012 Warning THE M8 HEXAGON SOCKET BUT EN 60079 7 2007 TONHEAD SCREW IN THE JUNCTION BOX EN 60079 28 2007 OF THIS LAMP SHALL NOT UNDER ANY CIR EN 60079 1 2007 CUMSTANCE BE OPENED OR LOOSENED THIS WILL AFFECT THE FLAMEPROOF E A SA PROPERTIES OF THE LAMP IEC 60079 7 2006 IEC 60079 1 2007 Note that changes to the product and or installation of IEC 60079 28 2006 components which do not conform to the approval may CE 0470 be a safety violation The manufacturer will not under any circumstances be held responsible for such activity For your health and safety always use safety gear suited for the task Be certain to follow codes regulations and or specific procedures that are related to the installation The maximum temperature at the entry point of the cable ex ceeds 70 C max temperature is 72 C Make sure that the cables and cable glands wich are used can withstand this temperature MAINTENANCE INSTRUCTIONS The floodlight should be inspected according to Compa ny routines The manufacturer suggests regular check for water intrusion in the termination compartment The light housing itself is a cemented EXd casing so this will have no technical concern When cleaning use only mild detergents Alcohol or petro leum based products may damage the gaskets TEF 9970 LED HELIDECK FLOODLIGHT USER MANUAL INSTALLATION INSTRUCTIONS Only qualified personnel are allowed to perform installation and m
5. le gland shall be over 75 C and under 55 C Stopping plugs and drain plug shall be IECEx ATEX ap proved according to IEC 60079 0 2011 EN 60079 0 2012 IEC 60079 7 2006 EN 60079 7 2007 for group IIB H and hold an IP grade of 66 or 66 67 The max and min tempera ture shall be over 75 C and under 55 C Any damage caused by the use of an incorrect combination of cable and cable gland is not the responsibility of Tranberg AS and is not covered by warranty TEF 9970 LED HELIDECK FLOODLIGHT USER MANUAL TECHNICAL DATA Material Marine Aluminum powder coated Borofloat safety glass Power consumtion Approx 45 W Input voltage 100 277VAC 140 277VDC Short circuit current 1500A 100 254V AC 47 63Hz Expected lifetime 50 000 h Weight 11 kg IP rating IP 66 IP 67 without drain plug Cable entries 2 PCS M25 x 1 5 entries for IECEx ATEX approved cable glands ac cording to IEC 60079 0 2011 EN 60079 0 2012 IEC 60079 7 2006 EN 60079 7 2007 Delivered with Tranberg cable glands Ex classification x Il 2 G Ex d e op is IIB H T4 Gb T5 version available Ex certificate no IECEx PRE 14 0060 Presafe 14ATEX5703 CE marking CE 0470 Max surface temp lt 135 C Tamb 55 C to 55 C 40 C for T5 Manufacturer Tranberg AS Dimensions
6. the connection compartment make sure no cables or the safety wire are jammed between the two parts Check the gasket and make sure that the gasket has no damages on the surface This will dramati cally reduce the ingress protection and impair the mode of protection regarding hazardous areas When mounted there shall be no noticeable gap between the top and the connection compartment Not following these instructions may lead to a risk of water ingress into the luminaire The manufacturer assumes no responsibility when these guide lines are not followed The terminals in this luminaire consist of a terminal block for phase conductors and PE Two M5 PE screws are fit ted to accept PE cables The terminal block is of the Cage clamp type and there is no need for a tool to connect or disconnect the phase conductors Nevertheless a large screwdriver preferably flathead may be a good help Termination Make sure to use IECEx ATEX approved cable glands ap proved for the specific cable diameter and type according to the relevant standards listed in APPROVALS for group IIB H These data can be found in the cable gland data sheet and declaration of conformity The cable gland shall hold an IP grade of 66 or 66 67 The max and min tem perature for the cab
Download Pdf Manuals
Related Search