2-Speed Hammer Drill
Contents
1. m 8 ta r Drill 006760 E DOUBLE INSULATION ENGLISH Original instructions Mode 8419B Steel 13mm Capacities Wood 30 mm Concrete 19 mm 7 High 1 300 No load speed min Low 1 000 NT High 14 300 Blows per minute min Low 11 000 Overall length 370 mm Net weight 3 0 kg Safety class 821 Due to our continuing programme of research and development the specifications herein are subject to change without notice Specifications may differ from country to country Weight according to EPTA Procedure 01 2003 END201 5 Symbols The following show the symbols used for the equipment Be sure that you understand their meaning before use eziuil Read instruction manual DOUBLE INSULATION Only for EU countries Do not dispose of electric equipment together with household waste material In observance of European Directive 2002 96 EC on waste electric and electronic equipment and its implementation in accordance with national law electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility ENE039 1 Intended use The tool is intended for impact drilling in brick concrete and stone as well as for drilling without impact in wood metal ceramic and plastic ENF002 1 Power supply The tool should be connected only to a power supply of the same voltage as2. indicated on the nameplate and can only be operated on single phase AC supply They are double insulated in accordance with European Standard and can therefore also be used from sockets without earth wire ENG905 1 Noise The typical A weighted noise level determined according to EN60745 Sound pressure level Lpa 94 dB A Sound power level Lwa 105 dB A Uncertainty K 3 dB A Wear ear protection ENG900 1 Vibration The vibration total value tri axial vector sum determined according to EN60745 Work mode impact drilling into concrete Vibration emission an p 15 5 m s Uncertainty K 1 5 m s Work mode drilling into metal Vibration emission an 2 5 m s or less Uncertainty K 1 5 m s ENG901 1 The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another The declared vibration emission value may also be used in a preliminary assessment of exposure WARNING The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger ti
3. replace strict adherence to safety rules for the subject product MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury FUNCTIONAL DESCRIPTION NCAUTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool Switch action 1 Switch trigger 2 Lock button NCAUTION Before plugging in the tool always check to see that the switch trigger actuates properly and returns to the OFF position when released To start the tool simply pull the switch trigger Release the switch trigger to stop For continuous operation pull the switch trigger and then push in the lock button To stop the tool from the locked position pull the switch trigger fully then release it Speed change 1 Speed change Switch To change the speed slide the speed change switch to the L position for low speed or the H position for high speed Selecting the action mode 1 Change ring This tool has an action mode changing ring For rotation with hammering turn the ring in the direction of multiple arrow indication For rotation only turn the ring in the direction of single arrow indication NCAUTION Always turn the change ring fully to your desired mode mark If you operate the tool with the ring halfway the tool may be damaged ASSEMBLY NCAUTION Always be sure that the tool is switched off and unplugg
4. your power tool serviced by a qualified repair person using only identical replacement 26 2T parts This will ensure that the safety of the power tool is maintained Follow instruction for changing accessories Keep handles dry clean and free from oil and grease lubricating and GEB003 5 HAMMER DRILL SAFETY WARNINGS 1 2 Wear ear protectors when impact drilling Exposure to noise can cause hearing loss Use auxiliary handle s if supplied with the tool Loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Always be sure you have a firm footing Be sure no one is below when using the tool in high locations Hold the tool firmly with both hands Keep hands away from rotating parts Do not leave the tool running Operate the tool only when hand held Do not touch the bit or the workpiece immediately after operation they may be extremely hot and could burn your skin Some material contains chemicals which may be toxic Take caution to prevent dust inhalation and skin contact Follow material supplier safety data SAVE THESE INSTRUCTIONS ZA WARNING DO NOT let comfort or familiarity with product gained from repeated use
5. ed before carrying out any work on the tool Installing side grip auxiliary handle Always use the side grip to ensure operating safety Install the side grip on the tool barrel Then tighten the grip by turning clockwise at the desired position It may be swung 360 so as to be secured at any position Installing or removing drill bit 1 Chuck key To install the bit place it in the chuck as far as it will go Tighten the chuck by hand Place the chuck key in each of the three holes and tighten clockwise Be sure to tighten all three chuck holes evenly To remove the bit turn the chuck key counterclockwise in just one hole then loosen the chuck by hand After using the chuck key be sure to return to the original position Depth gauge 1 Depth gauge The depth gauge is convenient for drilling holes of uniform depth Loosen the clamp screw and adjust the depth gauge to the desired depth After adjusting tighten the clamp screw NOTE The depth gauge cannot be used at the position where the depth gauge strikes against the tool body OPERATION NCAUTION Always use the side grip auxiliary handle and firmly hold the tool by both side grip and switch handle during operations Hammer drilling operation NCAUTION There is a tremendous and sudden twisting force exerted on the tool bit at the time of hole break through when the hole becomes clogged with chips and particles or when striking reinforcin
6. g rods embedded in the concrete Always use the side grip auxiliary handle and firmly hold the tool by both side grip and switch handle during operations Failure to do so may result in the loss of control of the tool and potentially severe injury Be sure to use a tungsten carbide tipped bit Position the bit at the desired location for the hole then pull the switch trigger Do not force the tool Light pressure gives best results Keep the tool in position and prevent it from slipping away from the hole Do not apply more pressure when the hole becomes clogged with chips or particles Instead run the tool at an idle then remove the bit partially from the hole By repeating this several times the hole will be cleaned out and normal drilling may be resumed Blow out bulb optional accessory 1 Blow out bulb After drilling the hole use the blow out bulb to clean the dust out of the hole Drilling operation NCAUTION Pressing excessively on the tool will not speed up the drilling In fact this excessive pressure will only serve to damage the tip of your bit decrease the tool performance and shorten the service life of the tool There is a tremendous force exerted on the tool bit at the time of hole break through Hold the tool firmly and exert care when the bit begins to break through the workpiece A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out However
7. me ENH101 14 For European countries only EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine s Designation of Machine 2 Speed Hammer Drill Model No Type 8419B are of series production and Conforms to the following European Directives 2006 42 EC And are manufactured in accordance with the following standards or standardised documents EN60745 The technical documentation is kept by our authorised representative in Europe who is Makita International Europe Ltd Michigan Drive Tongwell Milton Keynes MK15 8JD England 30 1 2009 AE Tomoyasu Kato Director Makita Corporation 3 11 8 Sumiyoshi cho Anjo Aichi JAPAN GEA005 3 General Power Tool Safety Warnings A WARNING Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool Work area safety 1 Keep work area clean and well lit Cluttered or dark areas invite accidents 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes 3 Keep children and bystanders away while operating a
8. or medication A moment of inattention while operating power tools may result in serious personal injury 12 Use personal protective equipment Always wear eye protection Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries 13 Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents 14 15 16 17 Remove any adjusting key or wrench before turning the power tool on wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards Power tool use and care 18 19 20 21 22 23 24 Do not force the power tool Use the correct powe
9. power tool Distractions can cause you to lose control Electrical safety 4 Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock 5 Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded 6 Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock 7 Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock 8 When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock 9 If operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 10 Use of power supply via a RCD with a rated residual current of 30mA or less is always recommended Personal safety 11 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol
10. r tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation Service 25 Have
11. se with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Tungsten carbide tipped hammer bit Blow out bulb Safety goggles Chuck key Grip assembly Depth gauge Drill chuck Makita Corporation Anjo Aichi Japan 883061B229 www makita com
12. the tool may back out abruptly if you do not hold it firmly Always secure small workpieces in a vise or similar hold down device Drilling in wood When drilling in wood the best results are obtained with wood drills equipped with a guide screw The guide screw makes drilling easier by pulling the bit into the workpiece Drilling in metal To prevent the bit from slipping when starting a hole make an indentation with a center punch and hammer at the point to be drilled Place the point of the bit in the indentation and start drilling Use a cutting lubricant when drilling metals The exceptions are iron and brass which should be drilled dry MAINTENANCE NCAUTION Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance Never use gasoline benzine thinner alcohol or the like Discoloration deformation or cracks may result Replacing carbon brushes 1 Limit mark Remove and check the carbon brushes regularly Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only identical carbon brushes Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps 1 Screwdriver 2 Brush holder cap ACCESSORIES NCAUTION These accessories or attachments are recommended for u
Download Pdf Manuals
Related Search