PIR-800 - Dustin
Contents
1. Note make sure the detection direction towards interior both installed on wall and at ceiling Adjust the bracket angle to optimize the detecting effect Avoid mounting the detector close to air conditioner electronic fan refrigerator oven heater and objects which will cause fast temperature changing and avoid mounting it in direct sunlight Avoid any objects blocking the lens so as not to influence the detection effect Detection Range Om 5m Om 5m Testing Walk Test After installation power on the detector After self testing for Iminute press the test button walk in the scope by crossing the infrared spectrum see below diagram and watch the LED indicator to make sure it is working The LED indicator will flash once when body movement is detected High detection sensitivity wig 1U65laH xeW Low detection sensitivity Connect with the Control Panel When the control panel is in connecting state press the test button twice to send wireless signal One beep is heard after panel receives signal which means successful connection Arm the system trigger the detector again The panel will alarm immediately This indicates the detector has successfully connected with the panel Specifications Power Supply DC 3V AAA LRO3 1 5V Battery x 2pcs Static Current lt 50uA Alarm Current lt 9 5mA Detection Distance 5m Curtain Detection2. is opened in working state the tamper switch will be triggered and then generates an alarm signal LED Indication The LED indicator can be turned on or off by setting jumpers See PCB Layout above Flash continuously Under self testing state Flash once Intruder is detected Flash twice Testing mode is finished enters power saving mode Flash once every 3 seconds Undervoltage indication please change the batteries immediately Usage Remove the battery activation strip to activate batteries It will enter working state after one minute s self testing Mode Setting Testing mode press test button the sensor enters testing mode and detects once every 10 seconds After 3 minutes the LED flashes twice the sensor enters the power saving mode Power Saving Mode In working state if the sensor is triggered twice within 3 minutes it will enter sleeping mode to save power After no movement within next 3 minutes the sensor goes back to the working state Installation amp Notice Wall mounting Fix the bracket longitudinally on the wall and put the detector on the bracket Choose to mount it at the entry and exit where intruder possibly breaks into It is suggested to mount it at the height of 2m from the ground Ceiling mounting Fix the bracket laterally on the ceiling upper the door or window and put the detector on the bracket Mount on wall wu9Elu6leH Xew Wg E 1U6leH xeW
3. Angle 15 Transmitting Distance lt 80m in open area Radio Frequency 315MHz or 433 92MHz 75KHz Housing Material ABS Plastic Operation Condition Temperature 10 C 55 C Relative Humidity lt 80 non condensing Detector Dimensions L x W x H 48 x 33 x 88mm Mounting Plate Dimensions L x W x H 52 x 30x 11 6mm Ver PIR 800 UM EN V1 0 2014 Chuango All rights reserved CHUANGO i t PIR 900 80 285X210mm 95X70mm I Ver PIR 800 UM EN V1 0
4. Curtain PIR Motion Detector PIR 800 User Manual Introduction The detector works based on detecting human body s infrared spectrum When human moves within the scope the detector receives the signal and inputs it into microprocessor after magnification Microprocessor continues to sample infrared signal and send wireless signal to wireless control panel after calculating thus to form a security system The product can be applied in balcony window door and corridor etc Features Accurate Detection Digital dual core fuzzy logic infrared control processing echnology Effectively identify interference signals from body movement signals through intelligent analysis Compact Design Small in size not much space occupation European style design adding artistic beauty to your home Flexible Installation Ceiling mounted or wall mounted for option Energy saving Featured energy saving mode enables 1 year standby Product Overview a 1 Detection Lens 2 LED Indicator 3 Test Button 4 Bracket oo 4 rai Infrared Sensor Zone Setting AS T 0Y1VVV AS T 0N1VVV Qf LED ON OFF aa O Tamper Switch Infrared sensor Detecting human body s infrared spectrum Don t touch the surface by hand and keep it clean Tamper switch Once the case
Download Pdf Manuals
Related Search