User Manual MMS-DLUX
Contents
1. Host Instruction Indicator Status Instructions olor indicator o Sms Flash slowly Searching the network Flash quickly Detection activated when power on PIR Sensor alarm or move ment detection alarm activated when in working status Constant Light No SIM card or malfunction Constant Light Arming status Flash slowly Disarming status Flash quickly Disarming status Restored to factory settings Light two Note Turn on the camera When the indicator lights on press seconds the RESET button until the indicator turns green it will restore to factory settings Note Slow flash Indicator flashes 1 time per second Quick flash Indicator flashes 2 times per second The indicator light can be enabled or disabled by pressing the RESET button for more than 10seconds when in normal status SIM card Installation Remove the cover and take out the battery Slide the SIM card into its holder with the contacts facing down as shown in the picture Insert the battery and then replace the cover Host Instruction Remote Control and Receiver Operation Instructions Connect the mini USB plug of the sensor receiver to the USB interface of the mobile guarder Connect the power adapter to the sensor receiver and open the sensor switch Press the arming button to the arming status The Mini guarder will trigger an alarm and send out SMS via the wire less sensor motion detection or infrared detectors Press the emer2. indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages In the interest of continued product development we reserve the right to make improvements to this manual and the products described herein at any time without notice or obligation DD v aa 8 9 All GSM SIM cards can be used capable of sending photos taken to MMS service enabled mobile phone or mailbox Integrated PIR sensor to provide a precise and timely alarm Built in CMOS camera and IR lights it can take clear images at night Movement detection it can detect movement in view Phone call and SMS central you can remote control the camera by phone call or SMS command Two way communication you can listen to the voice of the monitoring place and your voice can be broadcasted via a built in speaker Multi mode alarm it can alarm by SMS MMS E mail and phone call Schedule monitor it can time an alarm or monitor as the preset scheduler Backup battery built in lithium battery ensures continued operation in case of a power failure 10 Easy installation wireless connection it can be installed anywhere Product Accessories Manual Camera Adapter Remote Control Receiver Host Instruction Power Switch Camera Infrared Light Reset Button PIR Sensor Speaker Bracket Connection Diagram
3. famil family oeactivate MMS 115 0 Default timer sending 116 working days time period 1 start time time period 1 finish eea N amea endine time H time period 1 sending interval H time period 2 start time H time MMS period 2 finish time time period 2 sending interval time period 3 start time time period 3 finish time time period 3 sending interval Activate PIR sensor 118 1 Master family Deactivate PIR sen 118 0 Default sor 150 value Set time intervals RR Master family q Value is from 2 to 10 Default 2 minutes It means it will make an of infrared alarm l alarm again only 2 minutes later 210 value Value O or default 1 and Time intervals of Set combined alarm way Master family Or means it will make an alarm on either Mobile detection or Infrared human body detection And means it will make an alarm only if both Mobile detection and Infrared human body detection are opened 17 Appendix SMS command list H124EMMS center Master family Set MMS center Users need to reset MMS center depending on different networks such as Vodacom Mobile default 124 http mmsc vodacom4me co za 125 ip wapport httpport apn user pwd Users need to reset MMS parameter depending on different countries such as Vodacom Mobile default Set MMS pa rameter Master family 125 196 006 128 006 9201 80 mms vodacom net mms mmsH 127 value Master Change
4. User Manual MMS DLUX 10 11 12 CONTENTS Thank VoU a a E SS ra i a Roc 3 koryoursalety a eo so da seasestcrentene csr 3 Declaration sm Ra eee 3 Product Fete aa a a aa aid fa a RO O a A O E 4 PFOGUCTE ACCESSOMCS rrr ree o aa DE SED 4 LOST IMNSUGUCLIOM rca crser E E 5 Hostinstruetont so a Ra I E A 6 SIM Cara HISHONGHON eee TR eee car eae 6 Remote Control and Receiver INStructiONns cccccccsscsccesesrseeessees 7 SE cae g Caer aa am nero ee ner eer ory RA CD 8 About the SMS COMMMANA ccccccccccescscccssssceesssssescessesesssesesesseseenessees 8 SECIS eee ae aoe ate ORE RR CR eee eee ie 8 QUITE ES tall RC hone 9 wrrctac nts ieu cd esta ee tetera nade ares 9 ROWE ON Ofer ee eee ane ree 9 Add Fani US CRS sm Rm A 9 PT IVHOCO CMON CIS ce E RR 9 QuilceStanis a UR ee em ney tree ence et 10 10 Arming DEAM eee RR RR ee REMOTE ADN E E A A A E N A A ss T cern 10 OEK SEA A E A tenet 11 AE UNO e T E ETETE EOE 11 11 Voice Monitor amp SPCOKECL 0 cecscccesscecesssecesssecesssecesseecessaesesseecauaaeessaees 11 LANGU OIE e ne RS 11 SOUSOU E S forr inner O pa a q E GE O AA SR OG Os 12 QuileeStanias ao e scene one ieee eos eee eee 12 MESCIIFOGLONY SCLUINGS ram E RR O Rr anette 13 Maintenance DT E estate 14 TOD VES I OCA mca sere cao te ean eceeen cate acne ec ee ene neat 15 19 135172 SNIS Command Usinas eee Thank you Thank you for purchasing the MMS DLUX MMS DLUX is a smart GSMIGPRS remot
5. add up to 10 different family numbers HO H 07 password Status inquires 1 Password needed when guest sending O8 password Instructions Password is the current default one H O9 password H O9 password 1 Refer to Chapter 5 Quick start 19 Help H11H0H Deactivate SMS alarm Activate SMS alarm Default Deactivate MMS alarm Activate MMS alarm Default Deactivate call alarm Master family 11H 1 12404 Master family H12H1H 13404 13414 Master family Activate call alarm Default 14 new master number Master Change master number Instructions 16 digit max 1 Wn 14 Appendix SMS command list User Function SMS Command 22 value Value 1 mobile detection open O mobile detection closed default H36Hgradef Switch of mobile Master family E Sensitivity of mobile detection Master family Grade 1 2 3 4 5 optional from 1 to 5 stands for the sensitivity from low to high default 4 201 times Master family Set of mobile times Times from 2 to 10 Default 2 202 delaytime Delay time 1to 10 min default 2 minutes It means it will make an alarm again only 2 minutes later Delay time of Mo Master famil y bile detection alarm Send captured MMS Master family image to appointed guest mobile number or mail address 2 Guest need password Enable IR lights 31 1 Master family Disable IR lights H31H0H default 32 valu
6. ctory settings Please contact the operator Power off check the SIM card and restart in 2 seconds Weak signal or net Power off and restart in another place with After start up indicators Work busy stronger signal SIM card PIN code remain red flash does not amena ie PIN ae turn to green activated Invalid SIM card Check the SIM card status with the operator Failed to power on with external power after long time supply of battery Battery over dis Charge the battery for 1 hour power off and charged then restart Disorder of timed arming Wrong time in de i Check aut tic timi and timed MMS sending vice eck automatic timing once Note If the problem can t be solved with the above guidelines please contact your local dealer or after sales center 14 Appendix SMS command list HOOH Master Start the device Refer to Chapter 5 Quick start 1 start up HOLH Master family Arm the device Refer to Chapter 5 Quick start 4 Arming HO2H Master family Disarm the device Refer to Chapter 5 Quick start 5 Disarming Master family 03 password image number guest Master family guest Restore to factory set Master tings Master family SMS command guest User manual Capture MMS image Refer to Chapter 5 Quick start 6 Remote capture image HO4Hold password new password Instructions the length of master s password 4 digits O6 family number You are allowed to
7. e 30 password value image number 1 Value Mobile number or Mail address Value 1 160x128 normally used size for mobile phone 2 320x240 QVGA default 3 640x480 VGA Master family Change image size For example 32 1 means auto alarm image size as 160 128 H33Himage number Change alarm image Master family aber Number 2 8 optional and default to 5 max to 8 If image size is 640 480 the number can only be 1 2 34 value Master family Set image brightness The value can be 1 2 3 4 5 From 1 darkest to 5 brightest default to 35 value Master family Mirror image Value 1 mirror image of left and right O no mirror image default 38 value Master family Set image contrast The value can be 1 2 3 4 5 From 1 lowest to 5 highest default to 4 16 Appendix SMS command list 119 erade Master family Image quality Grade can be optional from 1 to 4 1 is lowest 4 is highest default is 3 Add or modify 108 EMAIL Email address Everyone can set one mail and can be modified 109 Master family Delete Email ee 110 value Value 1 send to mail Master family Alarm send to mail or not O not send to mail default Master family Note Sending to mail on the condition of opening the MMS sending 113 family user Delete famil i Mo tar cete Family users Th struction 113 means delete all the family users Activate MMS H115H1H timer sending Master
8. e camera It helps you achieve remote monitor alarm and shooting and thus provides a safe solution for protecting your privacy The built in 300000 pixels camera allows you to freely ask the device to take photos and send it to either your mobile phone or mailbox Images can be received as slide show by phone call or SMS command anytime anywhere With the built in IR lights it can take high resolution images even in a dark environment When anybody breaks in to your property it can trigger awareness immediately take photos and send it to you auto matically In this way your privacy safety and security can effectively be protected All functions and services are supported by the GSM network and SIM card For detailed operation and product func tions please read this user manual carefully 2 For your safety Please make sure the GSM SIM card PIN code de activated and caller ID presentation amp MMS service activated Please do remember and keep the password and SIM card number secret e Keep it away from signal interference e Donot use it in any explosive places e Please use the original power adapter to avoid any damage e Keep it out of the reach of children Declaration The information contained in this manual has been carefully checked and is believed to be accurate However we assume no responsibility for any inaccuracies that may be contained herein In no event will we be liable for any direct
9. elay make an alarm within 1 min when the power is on even if it detects people or movement Note Press the Reset button for 3 10 seconds it will automatically switch status between arming and disarming 211 value Remote control Master family Witch Value 1 Remote function open O Remote function closed default H212Htime begin time end Master fam Time period of astersTaM y remote control Default to 212 10 00 16 00 Change number of sol mio Master family alarm images for Number 2 to 8 optional default to 5 at most 8 If image size is timing MMS 640 480 the number can be at most 2 only 214 number Change number of Master family alarm images for Number number of images when you dial to obtain MMS 2 to 8 op remote capture tional default to 5 at most 8 If image size is 640 480 the number can be at most 2 only Thank you For any further assistance contact www securitywireless co za E mail gsmit wirelesscamera co za Tel 27 12 654 6209
10. er mobile phone number The num ber of family members that can be added is a maximum of 10 The same or repeated numbers will not be allowed Privilege levels for Master Family users and Guests Family Users Receive Phone Call Alarm Mo qro Ho Status ea Help and get Remote Capture Restore to Factory settings and add dei ii users phone num C a bers Quick Start Arming Disarmin To arm the device is to activate the alarm function thus the PIR sensor or movement detection turns to working state Product is set default to Arming status To disarm the device is to deactivate the alarm function the PIR sensor or movement detection There are two following methods Method 1 Send the SMS command to arm 01 You will receive the SMS reply Armed successfully and the indicator will turn green Send the SMS command to disarm 02 You will receive the SMS reply Disarmed successfully and the indicator will turn to a slow green flash Method 2 Make a call to the device via the master number or family number hang up in 5 20 seconds when you hear the ring tone and it will automatically switch the arming disarming status Method 3 Press the Reset button for 3 10 seconds it will automatically switch the status Remote Capture Method 1 Make a call to the device via the master number or family number hang up in 5 seconds when you hear the ring tone and you will receive the SMS reply Your requ
11. est has been received the device is sending image s now and then an MMS reply will follow Method 2 Send the SMS command Master family users 03 lmage number Guest H03HPasswordElmage number And you will receive the SMS reply Remote capture request received the device is sending image s now and then an MMS reply will follow f Note If image size set to 160 128 or 320 240 you can ask for 8 images at most i e 1 8 optional lf image size set to 640 480 you can ask for 2 images at most i e 1 2 optional 10 Quick Start Alarm With the built in PIR sensor the device can alarm once triggered default to SMS and MMS If the alarm SMS MMS and call options are activated at the same time it will send alarm SMS and MMS orderly and then make phone calls once for each For alarm calls it will dial the master number first and then family numbers until answered If no answer for an even 3 cycle calling then it will give up Notes The device is default to Movement Detection Alarm if you would like to change the alarm way please refer to the SMS commands list Voice Monitor amp Speaker Master and family users can dial the device number until the phone call gets through automatically to monitor the live voice If the speaker is open you can communicate to the monitored area too The speaker is default to open When an active alarming phone call gets through in an armed state the speaker will automatical
12. gency button this will call the preset numbers in turn under the default alarm condition Press the number buttons for phone calls if the mini guarder calls the preset phone numbers three times but without answer then it ll quit from calling status automatically Activate the camera in working status Turn offthe working status 1 2 3 4 5 Keys for 5 receipt numbers Last key for urgent alarm to master number will take away PPR Constant light when external power on CHG Constant light in recharging off when power full STA Receiver with slow flash under standby when receiving signals from remote controller of sensors will flash quickly about 3 seconds In addition when receiver is connected to the mini guarder if you turn off the mini guarder indicator the light of the receiver will be off automatically O About the SMS Command _ 1 All SMS commands are composed of symbols and Arabic numerals 2 SMS command format of master and family users code content 3 Password is four digit numbers default to 1234 4 The maximum digit of phone number is 16 5 When SMS command received it will automatically reply Note 1 The symbol is necessary for the SMS command but no space character included 2 1 15 SMS commands can be sent in one SMS separated by semicolon in English 3 The maximum length of SMS parameters is 50 characters or diaits 4 Allletters numbers and symb
13. language Value 0 Chinese 1 English default Master famil iringane i y device Refer to Quick Start 15 Timer arming 129 working days time period 1start time time period 1finish time time period 2 start time time period 2 finish time time period 3 start time time period 3 finish time Set time period of timing arming Master family For details of working days arming time and disarming time please refer to Quick start 15 Timer arming Turn into disarm 138 value Master family Status or not af Value 0 close ter alarm 1 open default l l 139 value Turn into disarm Master family status after sev Value 2 to 10 default 2 it means it will enter into disarm status after 2 eral alarms alarms 143 value l Disable Enable Master family ndor Value 1 Enable default O Disable Send SMS or 144 value Master family not if power sup Value 1 send SMS notice default ply changed O no SMS notice 148 value Set MMS sending Value 1 HTTP way Master family O WAP default 18 17 Appendix SMS command list 152 number Regulate device Master family time The number is the device SIM card number Activate Speaker Please regulate again when the battery is replaced or re installed Activate Speaker 164414 Master family Deactivate EEE Speaker 222 timedelay Delayed range can be from 1 to 30 Min Default to 1 Min i e it will not Master family Time D
14. lease make sure you add the password in the command only master has the rights to reset factory settings via SMS command If others send the command it will reply sorry you don t have the right to do it 12 Chapter 4 Maintenance Please use and store this product in suitable temperature Keep it away from excessive moisture and extreme temperatures Please keep the camera and all accessories dry Keep it away from water or any liquid Keep it away from dust alcohol acetone Please clean it with soft moist cloth do not use alcohol Acetone or other solvents Please refer to trouble shooting for problems solution Do not uninstall it yourself For other problems contact the dealers Please charge the battery for more than 12 hours to ensure optimum battery performance before your first use Charge it for 4 hours every 3 month if you don t use it 13 Troubleshooting Indicator light does not The indicator Press the RESET button for 10 seconds or send work light s disabled SMS command Start up fail but Indi AEU anne ont ingi Master already set Restore to factory settings cator works normally Caller ID presenta Functions failure but Indi tion or MMS ser cator works normally vice deactivated overdue No SIM card or Indicators remain on red poor wrong con tact Power off check the SIM card and restart in 2 Operation failure Malfunction seconds Or restore to fa
15. ly open so that you can commu nicate through the device Send the following SMS command and you can control the speaker 164 Value Value 0 to close speaker Value 1 to open speaker You will receive an SMS notification Speaker closed open Language There are two versions of language available send an SMS command for master only Chinese version 127 1 And you will receive the SMS reply Language switched to English Status Inquiries To ask the device for the present settings and working status send an SMS command as follows and you will receive a reply with all details password not included Master and family users 07 Guest 07 password 11 WAS quick start To ask the device for help send an SMS command as follows and you will receive a reply with command list or user manual For SMS commands Master or family users 09 Guest 09 password For User Manual Master or family users O9 1 Guest 09 password 1 Reset factory settings When the status of the settings is wrong it cannot recover even when the power is off You can than reset the factory settings clear all user s settings including master phone number Method 1 Power on when the indicator is off and before it lights again press the RESET button till it sounds Du and the factory settings have been reset successfully Method 2 Master sends an SMS command to the device O8 password Note P
16. ols should be SBC case Chinese characters not allowed Space not allowed Start Up Please set the master before you use this device or when restored to factory settings i e to let it recognize the master phone number so that it can send alarm SMS to the master automatically There are two methods as fol lows Method 1 Make a call with your mobile phone and you will hear it hang up Method 2 Send the SMS command to start up 00 After starting up you will receive the following SMS reply Welcome Congratulations on your purchase of MMS DLUX You are authorized to use this device Password 1234 Q Quick Start Power On Off Power on Keep pressing the power switch when power supply external power supply or battery is on During this period of time you will hear power on music then the indicator turns red and then off After a while it turns red again and flashes slowly till off and then turns green constantly green when armed slowly flashes green when disarmed and sounds DU then it turns to normal working status If it is set to arm after the designated time delay it will sound DU DU and turn to armed status The time delay can be designated by SMS command please refer to the SMS commands list Power on Arm time delay Power off Keep pressing power switch till you hear power off music Add Family Users Master can send SMS command to the device to add family users O6 family us
Download Pdf Manuals
Related Search