Guardcam Instruction Manual for SD card CCTV Recorder
Contents
1. danger of electric shock or other risks To avoid risk of burns due to high temperature do not touch the floodlight when it is turned on www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie2. ie CCTVIRELAND e 8 Please note when off record button is pressed remove SD card within 30 seconds now the LED will turn red after SD card is removed from the slot HE Reset button restore functions to default settings 1 Press RESET button once each time you turn on unit 2 Please press this button in case of system malfunction mM Off Rec Please press Off Rec button to remove SD card Please remove card within 30 seconds of pressing the Off Rec button to avoid loss of data RESET HH OFF REG y Audio Mode TIME DATE SET H o Fig 9 Step 6 Set the Date and Time This will allow the security video taken by GuardCam to display the correct date and time it was taken Push TIME DATE SET button see Fig 10 for 3 seconds The LCD screen will then flash 3 times indicating you have entered Time Date setting mode 1 YEAR setting Y and 08 are displayed on the Screen push the button to set year from O8 99 push the button again and hold for 3 seconds to scroll through numbers quickly If you have not pressed the button for 3 seconds it will automatically save the year and go on to allow you to set the month Repeat the same setting procedure for TIMEIDATE seT MONTH DATE HOUR MINUTE F s f 7 h F et Le www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie 2 VIDEO PHOTO setting when entering this mode t
3. 30 seconds When LED light turns green meaning SD card is being read do not remove SD card or data may be lost To remove SD card push in SD card to eject Once to unlock then pull out www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie Step 3 Installing the GuardCam IMPORTANT IF IN ANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT CONSULT A QUALIFIED ELECTRICIAN e This product must be grounded Do not mount the unit against inflammable surfaces e The motion detector will not operate correctly if it is installed Near the outlet of a central heating boiler Near air conditioning plant Pointing directly at moving vehicles Within sight of reflections from moving water Where other lamps could shine on the detector BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE ENSURE THAT THE ELECTRICAL SUPPLY IS SWITCHED OFF AND THE CIRCUIT FUSES REMOVED OR THE CIRCUIT BREAKER IS IN THE OFF POSITION Please make sure the voltage and polarity are correct before connection Incorrect voltage may cause electric shock If you are not sure please contact your retailer Note It is recommend to mount GuardCam 2M above the ground for optimum performance do not mount the fixture below 1 2M See Fig 3 for details of performance range Detection range 10M x 160 see Fig 3 www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie 6 Step 4 Mounting your GuardCam see Fig 4 amp Fig 5 1 P
4. F com RELANDie Guard L r Combined security camera floodlight system www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie Table of contents Contents of package sseresserrrssrersrsrr ers sr rr rss kr rr rk Kr sr KK rs ssd 3 GuardCam Motion Light with Video Camera sssisserrrrrrrerr rr rr rr rss 4 Step 1 Assembly 1 ccc ccc etc rare rr rr rskr rr Arr K KRKA 4 Step 2 Insert remove SD Card oo cece cece rs rr rr rr rr rr rar rs 5 Step 3 Installing the GuardCam cece cc tee tet rr rr rr ss 5 Step 4 Mounting the GuardCam cece eee tee teen rr rss 6 Step 5 Adjusting the settings ccc cece eect etter ee eenaes Step 6 Set the Date and Time sssssssesesreesrrrrrrsrrrr rr rr rr teens 9 Step 7 Viewing video ssssererrrrrrsrrsrsrsssrs rss Than rr rr rr Kr rr rss 10 Technical Specifications ossssssrrrrrrerrrrrrrrr rss rr rr rr rr rr rr rr ac 10 General Information and Safety cece cece cence rss rr rss sars sa 11 Contents of package Duard Can GuardCam Motion Light with Video Camera 1 x Allen key 2 X SCrews 2 x plastic masonry plugs 2G SD card SD card reader www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie 3 GuardCam Motion Light with Video Camera overview Floodlight Cover ake alba Ga at T Halogen lamp Waterproof cover 3 mode selection Camera lens PIR lens Low battery indicator 35 Step 1 Assembly Install replac
5. d sharpness Auto Date amp Time stamp Effective viewing angle 60 deg Effective viewing distance 8M Image format JPEG AVI File Powered by AC 100V to 240V subject to requirement Halogen tube 230W Auto light sensor Sensitivity control Floodlight time delay control www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie F cctv RELANDie 11 General Information and Safety SPECIAL CARE INSTRUCTIONS The GuardCam Motion Light with Video Camera is designed to be weather resistant Never attempt to immerse the unit in water or any other liquid This will damage the unit and void the warranty This product is designed to illuminate video and make verbal announcements It will not prevent the commission of any act legal or illegal The manufacturer assumes no liability for any damage to property injury to person or death Use a Soft lens cloth for cleaning lens Avoid touching lens with fingers Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep the GuardCam Motion Light with Video Camera in a dry and cool dust free environment or container when it is NOT used Do not open the GuardCam Motion Light with Video Camera for unauthorized Service This could cause serious damage to the unit and will void the warranty This GuardCam Motion Light with Video Camera is a precision electronic device Do not attempt to service this camera yourself as opening or removing covers may expose you to the
6. e the halogen lamp see Fig 1 IH Make sure to unplug unit or turn off power first M Remove floodlight cover by unscrewing floodlight screws using a Phillips head Screw driver BH If replacing a bulb take out the existing halogen light bulb Put in new 230 Watt maximum halogen light bulb M Replace floodlight cover tightening screws carefully www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie 4 Installation and replacement of back up batteries The Function of the back up batteries is to Provide power to complete a part finished recording if a mains power outage occurs and preserve date time settings for a minimum of 120 hours prior to mains power being restored Unscrew the screw A and remove back cover Unscrew screw B and remove battery cover Put the 3pcs AAA 1 5V batteries into the battery compartment and make sure the polarity is aligned correctly Replace battery cover and back cover tightening screws carefully Note To guard against damage from battery leakage it is good practice to replace batteries on a yearly basis To maintain battery back up function please replace batteries after a total of 120 hours of mains power failure Step 2 Insert remove SD card see Fig 2 Unscrew the waterproofed cover using provided Allen key then insert the SD card until it automatically locks into place If you need to remove the SD card please press OFF button and take it out within
7. hese two icons Brand V appear on the screen push the button to choose V Video or P Photo If you have not pushed any buttons for 3 second OK will appear on the screen indicating it has automatically saved the current settings The LCD screen will Shut off automatically 10 seconds later On the P photo setting GuardCam will take a series of digital photographs at a rate of 3 photos every second when the motion sensor is triggered GG setting 3 3 MONTH af Q 4 DATE K Setting L Ft Pd Setting HOUR AR MINUTE o Setting k J Setting VIDEO PHOTO Setting Step 7 Viewing Video Viewing image by computer through a card reader see Fig 11 M Open the waterproofed cover on the GuardCam Motion Light with Video Camera M Press OFF REC button and remove SD card from the slot M Put the SD card into the card reader supplied then insert the card reader into PC via a USB port and open Windows Media Player to view the video www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie 10 Technical Specifications Features and specification PIR detection angle 160 Deg and detection range up to 10M Records 20 seconds image recording for image stream 10fps at 480 640 Pixels Built in SD card slot for SD memory card SD card slot for additional storage max memory size up to 2G SD card specification FAT Automatic exposure control white balance an
8. lace plastic masonry plugs into desired surface aligning holes as Shown below Using an electric screwdriver fasten mounting plate directly to surface using screws E 2 Feed the cable through the back mounting box and bush the cable entry to avoid abrasion to the cable 3 Wire the unit as follows Ensure all ae 2 Greanivellow sl wires are connected securely and p that no loose strands are exposed INCOMING SUPPLY TO FITTING EARTH Green amp Yellow gt if a EARTH Green amp Yellow amp a NEUTRAL Blue or Black NEUTRAL Blue or Black H LIVE Brown or Red LIVE Brown or Red 4 Make sure the polarity is correct Double check the connections after wiring Errors may damage the motion sensor or cause a fire hazard 5 Attach the unit to the mounting plate You will first need to angle the unit back so that the catch at the top of the mounting plate fits into Slot on the back of the unit Next lower the unit until holes at the bottom of the mounting plate and unit are flush Then screw screw A into this hole tightening carefully Please allow 1 minute warm up time after switching on Push the RESET button after switching on Remove plastic lens cover from camera after installation see Fig 6 www cctvireland ie Lo Call 1890 866 900 e sales cctvireland ie Step 5 Adjusting the Settings see Figs 7 9 Time control Turn the time control knob to side to i
9. ncrease the illumination time 7 minutes max turn the control knob to side to reduce the illumination time 30 seconds min Sensitivity control Adjust the detector range of Passive Infrared Motion Sensor 2M gt 10M Fig 7 Selecting working mode Mode 1 Suggested setting when out of town Light camera speaker all day detection Daytime and nighttime light camera and speaker are all in operation Mode 2 Suggested for day to day use Light at night camera all day speaker in the daytime Daytime light is off camera is on Speaker is on Nighttime light is on camera is on speaker is off Mode 3 Perfect for a place of business Light at night camera all day speaker at night Daytime light is off camera is on speaker is off Nighttime light is on camera is on Speaker is on Audio mode for different sound selection Pre set default is silent mode push one time for ding dong push again for dog barking Push one more time for the message you just recorded LED indicator for indicating the function status of the unit by different colour LED lights 1 Red SD card is not inserted into the SD slot or the system is malfunctioning 2 Green The unit is recording or USB is inserted and connecting with the computer LED off stand by SD card is inserted into the slot when off record button is pressed www cctvireland ie Lo Call 1890 866 900 e sales cctvireland
Download Pdf Manuals
Related Search