G797 Revised
Contents
1. G797 Tracking Device User Manual Version2 01 TABLE OF CONTENTS 1 Device Introduction 1 1 Physical Appearance 1 2 Specification 1 3 Features 2 Quick Install Instructions 2 1 Open device 2 2 Insert SIM card 2 3 Power on 2 4 Configuration 2 5 Location OBDII Port 2 4 Set User No 2 5 Modify Password 2 6 Set Work Mode 3 Commands for Device Setting 3 1 Command Table 3 1 1 Set User No 3 1 2 Modify User Password 3 1 3 Set Upload Mode interval and type 3 1 4 Clear Alarm 3 1 5 Location Poll 3 1 6 Set Message Center Number 3 1 7 Set APN 3 1 8 Set Voice Monitoring Number 3 1 9 Enable Disable Over speed alarm 3 1 10 Enable Disable Over Speed Alarm Parameter 3 1 11 Enable Disable SMS when movement trigger 3 1 12 Set Time Zone 3 1 13 Immobilizer Output 3 2 Combine Command 3 3 Commands Wait 3 4 Alarms 3 5 Default Parameters 4 Structures of SMS from Device 4 1 Normal Location SMS Format G Mode 4 2 Hyperlink SMS Format W Mode 4 3 Error Command Alert 4 4 Password Modification Successful Confirmation 4 5 User No Setting Successful Confirmation 5 LED Flashes amp Relevant Device Status 6 Appendix 6 1 Characters for Commands 02 04 06 07 08 08 09 10 11 13 T3 13 13 13 13 14 14 14 14 14 14 15 15 15 16 16 18 19 19 20 20 20 21 23 1 DEVICE INTRODUCTION G797 which uses GSM and SMS together with GPS to locate your belongings is a new mod2. SOP 100 120 MOT 0 Remarks Total is 20 bits 86 is national code must have Leave factory set empty Default usually no need to set SMS center number when user use SIM card device will record SMS center number automatically when change SIM card the old number will be delete and record new one Parameter range APN 1 30 characters user name 0 30 characters password 0 30 characters The second command way APN APN Means only set APN Device comes with of some APN list of some mobile service providers for some country when the APN information is included forthe SIM card used no need to configure if APN is wrong GPRS connection will be wrong 86 is country code The number can t be empty Usage send command the device will call back open microphone user start monitor 0 close 1 open Default SPO 1 100 prompt 120 alarm Default SPO 80 100 0 Close shielding sensor related function IS cancelled relevant information don t send 1 open can Use related functions of movement sensor E Sr Description Ctrl WordCommand Reply Remarks Set local time zone parameter from 12 00 to 12 00 Negative 3i2Time zone N vt represent western time zone setting TZN TZN 8 00 TZN 8 00 positive represent east eastern time zone Default 0 00 0 close am 1 open device send power FE Immebilzer IMM IMM O IMM 0 cut command or the device is Output di isconnection cut powe
3. 1234 UNO 861391 2345678 UPW 1234 UUM 30M G T UAC PRQ Reply 1 UNO 139123456 78 2 UNO 86139123 45678 UPW 1234 UUM 30M G T UAC PRQ Remarks 0 20 bits default is empty 1 set national number 2 set international number 86 is country number Four bits range 0000 9999 30M upload interval M can be 30 900S 15 59M 1 240H Default 30m G W G upload mode it can be O close uploading G upload GPS data by interval set when there is no GPS data uploading based on base station information S Always upload with LBS location T data format it can be T Text Format W Hyper link Format Usage send command to device the device will upload information Information format is the same as upload data by interval and this function can also be done by calling to the device and hang up after first ring E Sr ES 316 317 318 319 3110 311 Description Setting the SMS center number Set APN Monitor Enable disa ble over Speed Speeding alarm parameters Motion sensor enable and disable Ctrl Word SCN APN VOM SPO SOP MOT Command SCN 8613800200500 APN APN user name password APN APN VOM 13912345678 or VOM 861391234567 8 SPO 0 SOP 100 120 MOT O Reply SCN 8613800200 500 APN APN user name password APN APN VOM 13912345678 or VOM 8613912345 678 SPO 0
4. 5 Located Unsuccessful Gosafe G797 V1 05 MCC 460 MNC 1 LAC 517A CID 1FB1 TMP 25 6C PWR 12 5V Device Name and Version Satellites Connected amp Time used for Location secs Specific time zone and Location time based on specific time zone Latitude in degree minute format Longitude in degree minute format Device speed and Move Direction Temperature Power Device Name and Version Mobile Country Code Mobile Network Code Location Area Code Cell Identity Temperature Power 4 2 HYPERLINK SMS FORMAT W MODE Located Successful Google link Gosafe G797 V0 10 http maps google com static map zoom 14 amp size 150x150 amp markers 39 9493 116 3875 amp sensor false TMP 25 6C PWR 12 5 Located Successful Yandex link Gosafe G797 V0 10 http m maps yandex ru ll 1 16 3875 39 949328 amp pt 1 16 38 75 39 949328 amp z 12 TMP 25 6C PWR 12 5V Device Name and Version Google Map Link Temperature Power Device Name and Version Yandex Link Temperature Power 8 Located Unsuccessful Gosafe G797 V0 10 Device Name and Version MCC 460 Mobile Country Code MNC 1 Mobile Network Code LAC 517A Location Area Code CID 1FB1 Cell Identity TMP 25 6C Temperature PWR 12 5V Power 4 3 ERROR COMMAND ALERT Gosafe G797 V0 10 Error command 4 4 PASSWORD MODIFICATION SUCCESSFUL CONFIRMATION Gosafe G797 V0 10 UPW 5678 4 5 USER NO SETTING SUCCESSFUL CONFIRMATION Gosafe G797 V0 10 UNO 86139123
5. LED light will ON for 1sec then flash quickly which helps trouble shoot errors user can count LED quick flashes then compare it to below chart JB Error Details GSM module Communication Error SIM card Error Cannot register at GSM network GPS module Error SMS Sending Error Can t use GPRS TCP connection Error Unknown Error LED Flashes 1 flash 2 flashes 3 flashes 4 flashes 5 flashes 6 flashes 7 flashes 8 flashes Solutions Power OFF then check GSM module power supply and communication Power OFF then check whether SIM installation is good and PIN is disabled To check whether SIM card is overdue and or device in an area there is no GSM signal Power OFF then check GPS module power supply and communication To check whether there is SIM card SMS To check whether there is SIM card SMS center setting error and orSIM card is overdue To check whether the APN is correct and SIM has GPRS function or not To check if the server is normal Power OFF then Power ON if there is still the error please contacts us B 6 APPENDIX 6 1 CHARACTERS FOR COMMANDS Sp ar www gosafesystem com
6. 45678 B 5 LED FLASHES amp RELEVANT DEVICE STATUS There is an external LED light to reflect device status in G797 In order to check device status through this LED light flashes LED is located right next to the USB port When device is at work LED will flash at 8 sec cycle constantly to show related GSM and GPS status in each cycle In each flash cycle when device is at work LED will flash to indicate GSM status first then GPS status there is an interval between them To check the statuses please count the LED light flashes then compare it to the chart below Status LED Flashes Device Power on LED ON lt 1sec GSM module ON but unregistered 1 flash at the beginning of each flash cycle GSM module ON and registered 2 flashed at the beginning of each flash cycle GSM module OFF No flash at the beginning of each flash cycle GSM module on and registered 3 flash then GPRS connection GSM module on and registered 4 flash then TCP connection GPS module ON but haven t located 1 flash after interval behind GSM status flash in each flash cycle GPS module ON and located 2 flashes after interval behind GSM status flash in each flash cycle GPS module OFF No flash after interval behind GSM status flash in each flash cycle Device also uses LED flashes to indicate relevant error if any of the following situations happens Device Error SIM card no balance GSM network cannot register When there is any error as mentioned above
7. IM card into the SIM card jacket correctly according to the below picture Press SIM card inside the SIM card jack completely Note Please do activate the SIM card disable its PIN code function and make sure SIM card has enough balance before operating the device Each time before taking SIM card out of or inserting SIM card into the device device power supply remove the device from the OBDII connector or it would damage device and or your SIM card JR 2 3 POWER ON Connect battery to the device like the below picture shows you 2 4 CONFIGURATION Connect USB cable to device and computer Use the configuration software to configure B 2 5 LOCATION OBDII PORT Normally ODBII port is available in all the vehicles manufactured after the 1996 and 2000 This port is located under the dash near the driving side of the vehicle Normally this port is covered with some cover 2 6 SET USER NO 1234 UNO 8613912345678 1234 UNO 13912345678 UNO 13912345678 UNO 8613912345678 with country code without country code Command Control Word Send SMS Reply Note After receipt of the above SMS command device will reply a confirmation SMS and work at default work mode 30M G W To protect device if there is any error in this command device will not send back any error warning B 2 7 MODIFY PASSWORD To mo
8. M APN list User password User upload mode Manager phone number Manager upload mode Server IP or domain name TCP port UDP port TCP channel upload mode mode 0 UDP channel upload mode mode 0 Package number of per TCP upload Package number of per UDP upload percentage of data buffer per TPC upload percentage of data buffer per UDP upload Over speed Enable disable over speed alarm Enable disable vibration sensor Enable disable phone roaming status test Enable disable anti jamming Time zone Vibration sensor parameter Anti jamming parameter Baud rate of extend serial port Transmit mode of extend serial port USB port mode Supper link 0 GPS Link Supper link 1 LBS Link Phone list of SMS forwarding Hot line list Time for talking SMS number counter Parameter EMPTY EMPTY 1234 APN list of China only 1234 30M G W empty 30M G T domain name empty IP 114 142 154 28 3032 3032 605 G B 6085 G B 1 1 50 50 80 100 Disable Disable Enable Disable 0 00 10 10 30 30 20 9600 Common mode Common mode http maps google com staticmap zoom 14 amp size 300x300 amp markers n e amp sensor false empty empty empty 0 0 0 0 E 4 STRUCTURES OF SMS FROM DEVICE 4 1NORMAL LOCATION SMS FORMAT G MODE Located Successful Gosafe G797 V0 10 GPS 3 56 LTMO08 00 11 24 10 02 54 N23 9 8329 E113 25 7149 Speed 1km h 39 TMP 25 6C PWR 12
9. dify factory password at the first usage is strongly suggested Message UPW 5678 1234 UPW 5678 New Password Command Control Word Factory Password Send SMS gt Reply Note Please memorize your New Password and wait for confirmation SMS for password modification from device Only if this command is sent by user No the system can process this command 8 2 8 SET WORK MODE There are 4 different work modes configurable for device according to user s need O S G and L For detailed information on 4 work modes please go to Commands for Device Setting in this User Manual the type of message Message 1234 UUM 30M G T the Work Mode user wants to configure Command Control Word Password Send SMS Reply UUM 30M G T JB 3 COMMANDS FOR DEVICE SETTING All the commands for device setting in this User Manual are in the same format 3 1 COMMAND TABLE The user command is shown in the below table The whole command format is PSW CMDXX Para Table only show the second part CMDXX Para in the column of command format S c Description 311 Setting user phone number UNO 312 Setting user password Ua 313 Setting usersyyM to upload mode 314 User alarm cleared UAC 315 Requests for location information PRQ Ctrl Word Command 1 1234 UNO 1391234 5678 2
10. eceived is as follows when device is in alarm G797 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Power Off LIST OF ALARMS Description SMS Received Power Off G797 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Power Off Over Speed G797 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Over Speed 8 Description Moving When the vehicle stopped and the movement sensor is enable the device sends move alarm on the trigger of movement sensor Geo Fence Future use the current version firmware don t support it Anti Jamming This alarm appear if the anti jamming feature is enable and the someone use GSM jammer near the device SMS Received G797 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Moving G797 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Geo Fence G797 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Anti Jamming Note The user can use the UAC command to clear user based alarm 3 5 DEFAULT PARAMETERS Device is set with the following default parameters When device powers up first time it will use the following parameters to connect and wait for user commands or server commands Description User number SMS center number PIN code of SI
11. el tracking device designed by Gosafe Company Limited With connect amp Go concept G797 can connect with OBDII diagnostic port and can get necessary power from the same port Inside G797 there are GSM modem GPS receiver control PCBA microprocessor power circuit and so on Before starting G797 installation please one SIM card which works on GSM based network that is offered by GSM mobile operating agency and can work with GPRS G797 is easy to install device and even nonprofessionals can install this device You only need to get the valid data SIM Card Insert the SIM card in G797 and connect the device to OBDII port in the vehicle The system have internal movement sensor which controls the power management of the device G797 is equipped with highest available GPS uBlox modules and able to use A GPS Assist GPS technology to give help connecting the device with GPS faster with more accuracy JB 1 1 PHYSICAL APPEARANCE Device and Components Device opening to insert SIM card Front Cover Back Cover MIC USB Port Accsessories RF Wireless Relay RF Tag USB Configuration cable Front View USB Port Wireless Module LED GPS GSM LED 2 1 2 SPECIFICATIONS Physical Specification Size Weight IP Rating Power Rechargeable Battery Power Consumption MCU MCU GSM Antenna Modem Frequency GPRS Approvals SIM card LBS Location Accuracy GPS Antenna Receiv
12. er Channels Sensitivity Navigation update Acquisition Location Accuracy 55x50x25mm 80g IP62 Connector J1962 7 4V 180mAh Lithium ION Sleep Mode 500uA Active 70mA TI MSP430 12KB RAM 256KB Flash Internal uBlox LEON G100 Quad band 850 900 1800 1900MHz Class 10 4 downlink 2 uplink max 5 Mobile Station Class B AT amp T R amp TTE CE GCF FCC PTCRB Anatel IC China SRRC etc 3 3V SIM 100 to 500meters Urban 0 5 to 30kilometers Suburb Internal uBlox NEO 6M GPS amp Sbase engine 50 Parallel Channels 162dBm 1sec Cold Starts 27s Aided Starts 1s Hot Starts 1s 2 5 to 10meters Strong Signals 500 meters Weak Signals JB Sensor 3D G Force Sensor Memory Flash Environmental Conditions Operating Temperature Storing Temperature Humidity Onboard 10 000 Locations 40 C to 70 C 40 C to 85 C 95 1 3 FEATURES Real Time Location Mobile Map Location Latitude and Longitude Location GSM Base Station Location LBS Technology Convenient GSM Mobile Control Easy to use SMS Communication Mode Internal Movement Sensor for better power management Internal backup battery for Device disconnection notification Internal memory for the data buffer 8 2 QUICK INSTALL INSTRUCTIONS 2 1 OPEN DEVICE WS efully by screwing off the four scre Open G797 enclosure car a 2 2 INSERT SIM CARD Insert S
13. r of vehicle 3 2 COMBINED COMMAND To save time and SMS resource on configuration user can apply combine command in which there is more than one command to operate configuration The combine command would begin with user password which is followed by commands commands order is flexible Format is as follow Command Command Pw Parameter Parameter Parameter word word First command Second Command If there is duplication of the same command in the same combine command just the last piece of command would be processed if there is error in the command the command with error would be discarded and device would only confirm setting of correct commands with no error warning If all the commands are error an alarm will be sent All setting commands except user No setting command under the condition of the user number has never been changed can be set by combine command Example 1234 UUM 30M G T UPW 1234 8 3 3 COMMANDS WAIT In the event that if commands come from user when device is in sleep mode then the device couldn t process commands however at each wakeup device will wait one minute to receive those commands and take precedence to process them then response one confirmation message after 1 min device would receive and process real time commands and will reply accordingly 3 4 ALARMS The device sends alarm immediately when it triggers The message r
Download Pdf Manuals
Related Search