USER MANUAL
Contents
1. a IR OUTPUTS RS 23241 RS 232 2 Teue 2 TITT D o 66 102 304 O GRxTx GRxTx jaa FEIT e O Figure 1 PL 18 Control Port Expander Table 1 PL 18 Control Port Expander Functions Feature Function 1 ON LED llluminates green when receiving power 2 RS 232 Tx Rx LEDs Illuminate red while transmitting and green while receiving data on an RS 232 port 3 IRLEDs Illuminate green when an IR port is active 4 RELAY LEDs Illuminate green when an relay is active from 1 to 4 5 PROGRAM USB Connector Connects to a computer to upgrade firmware 6 RELAY Terminal Blocks Connect to relay driven devices from 1 to 4 7 IR OUTPUT 3 5mm Mini Jacks Connect to IR emitter cables from 1 to 2 8 RS 232 1 Terminal Block Connects to an RS 232 device that is controlled 9 RS 232 2 Terminal Block Connects to an external controller PC touch screen or RC device 10 PROGRAM Switch For factory use only Do not operate during firmware upgrade 11 5V DC 5V DC connector for powering the unit 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the PL 18 Control Port Expander 5 Connecting the PL 18 Control Port Expander To connect the PL 18 as the example in Figure 2 illustrates do the following 1 Connect the RS 232 ports as follows Connect RS 232 1 to a projector Connect RS 232 2 to a PC touch screen or an RC device 2 Connect the RELAY terminal block connectors as fo2. Formal syntax with commands concatenation and addressing Start Address Body Delimiter Destination _id Command_1 Parameter1_1 Parameter1_2 ICR Command_2 Parameter2_1 Parameter2_2 Command_3 Parameter3_1 Parameter3_2 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Protocol 3000 Syntax 9 3 Start 9 3 1 Start 9 4 Device Message Format Address optional Body delimiter Sender_id Message CRI LF Device Long Response Echoing command Address optional Body Delimiter Sender_id Command SP Param1 Param2 result CRIILFI CR Carriage return ASCII 13 0x0D ILF Line feed ASCII 10 0x0A ISP Space ASCII 32 0x20 COMMAND TERMS Command A sequence of ASCII letters A Z a z and Command and parameters must be separated by at least one space Parameters A sequence of alphameric ASCII characters 0 9 A Z a z and some special characters for specific commands Parameters are separated by commas Message string Every command entered as part of a message string begins with a message starting character and ends with a message closing character Note A string can contain more than one command Commands are separated by a pipe l character Message starting character For host command query For machine response Device address Optional for K NET K NET Device ID followed by
3. 01 82 80 81 Emit via IR port 2 forty two bytes the binary representation of Kramer signal button 1 bin ir 2 42 lt CR gt FF 01 8F 69 67 65 66 69 66 6C 63 66 C9 68 C8 66 CB 66 C8 CE FF 01 BC 69 66 66 C8 69 66 69 66 66 66 69 66 69 65 67 65 FF EF 26 Using the binary port to receive and convey binary data Convey four binary bytes received on serial port 1 these four binary bytes are the binary representation of the P2000 all in 2 serial command rbin uart 1 4 lt CR gt 01 82 80 81 J 8 2 Help Commands Command Syntax Response Protocol handshaking HCR OKICRLF 8 3 Result and Error Codes Result Error Syntax Command ran successfully no error ICOMMAND PARAMETERS OK Protocol Errors Syntax error ERR001 Command not available for this device ERR002 Parameter is out of range ERR003 Unauthorized access command run without the matching ERR004 login 8 4 Identification Commands Command Syntax Response Protocol handshaking ICRI OK CRLF Read device model MODEL MODEL MACHINE_MODEL Read device serialnumber SN SN SERIAL_NUMBER Read device firmware VERSION VERSION MAJOR MINOR BUILD REVISION version Set machine name NAME MACHINE_NAME NAME MACHINE_NAME RESULT Read machi
4. Query sign follows some commands to define a query request All outputs sign defines all outputs Message closing character CR For host messages carriage return ASCII 13 11 Protocol 3000 Syntax 9 5 9 6 9 7 9 8 9 9 CRLF For machine messages carriage return ASCII 13 line feed ASCII 10 Command chain separator character When a message string contains more than one command separate each command with a pipe l character Spaces between parameters or command terms are ignored Entering Commands You can directly enter all commands using a terminal with ASCII communications software such as HyperTerminal Hercules etc Connect the terminal to the serial Ethernet or USB port on the Kramer device To enter CR press the Enter key LF is also sent but is ignored by command parser For commands sent from some non Kramer controllers like Crestron some characters require special coding such as X Refer to the controller manual Command Forms Some commands have short name syntax in addition to long name syntax to allow faster typing The response is always in long syntax Command Chaining Multiple commands can be chained in the same string Each command is delimited by a pipe character l When chaining commands enter the message starting character and the message closing character only once at the beginning of the
5. 2 PL 18 Control Port Expander Technical Specifications PORTS 2 bi directional RS 232 ports on terminal block connectors 1 USB OUTPUTS 4 relays on terminal block connectors 36V AC or DC 1A 60V AC max on non inductive load 2 IR outputs on 3 5mm mini jack connector LED INDICATORS ON green RS 232 Tx red and Rx green IR green relays green POWER SOURCE 5V DC 260mA DIMENSIONS 12cm x 7 6cm x 2 4cm 4 72 x 2 97 x 0 96 W D H WEIGHT 0 6kg 1 4lbs ACCESSORIES Power supply 5V DC OPTIONS 15 meter and 20 meter IR emitter extension cables 1 When configuring an RC 2 to work with the PL 18 the RC SV software version must be at 2 1 2 32 or higher and the RC 2 firmware version must be at 1573 or higher 2 At www kramerelectronics com 3 Specifications are subject to change without notice KRAMER SIMPLE CREATIVE TECHNOLOGY PL 18 Commands in Protocol 3000 8 PL 18 Commands in Protocol 3000 This section describes all commands sent to the PL 18 For an explanation of the syntax and use of Protocol 3000 see section 9 8 1 Operating Commands Following are the specific commands that the controller RC device sends to the PL 18 on RS 232 2 to operate the external devices connected to RS 232 1 the IR ports and relays Command Syntax Response Relay control RELAY PORT_NUM STATE RELAY PORT_NUM STATE Paramet
6. Progress Figure 11 Completion Message Tables Table 1 PL 18 Control Port Expander Functions Table 2 PL 18 Control Port Expander Technical Specifications 14 15 15 16 17 18 18 19 19 ii KRAMER SIMPLE CREATIVE TECHNOLOGY Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer TOOLS PL 18 Control Port Expander which is ideal for e Controlling multimedia rooms such as classrooms auditoriums conference rooms and so on Each package includes the following items e The PL 18 Control Port Expander e Windows based Kramer control software and Kramer RC SV Configuration software e Power adapter SV DC input i 2 e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix S
7. Progress 11 When the upload is finished the completion message appears Figure 11 Completion Message 12 Click Close to close the P3K Wizard and remove the cable that connects the PL 18 to the PC 19 Using the P3K Wizard 10 2 Changing the Device Parameters To change the device parameters for example the K NET ID do the following 1 Connect a PC to the PL 18 see section 10 1 2 2 Open the Kramer P3K Wizard by double clicking the desktop icon P3K Wizard The P3K Wizard screen appears see Figure 3 Click the Connect button to open the Connect window see Figure 4 4 Choose the SERIAL USB connection and click OK The Connect window disappears and the Device Properties become visible 5 Change the parameters as required and click SET 1 You can download and install the latest version of the P3K Wizard from www kramerelectronics com 20 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warra
8. string and at the end Commands in the string do not execute until the closing character is entered A separate response is sent for every command in the chain Maximum String Length 64 characters Backward Support Protocol 2000 is transparently supported by Protocol 3000 You can switch between protocols using a switch protocol command from either platform 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the P3K Wizard 10 Using the P3K Wizard The P3K Wizard is a Kramer software program for e Upgrading the machine firmware see section 10 1 e Accessing and changing device parameters see section 10 2 The P3K Wizard can be downloaded from the Kramer Web site 10 1 Updating the PL 18 Firmware The PL 18 uses a microcontroller that runs firmware located in FLASH memory The latest version of firmware can be downloaded from the Kramer Web site and updated in minutes using the PK3 Wizard and the following procedures To update the PL 18 firmware e Download the firmware file from the Internet see section 10 1 1 e Connect a PC directly to the PL 18 see section 10 1 2 e Update the firmware using the P3K Wizard see section 10 1 3 10 1 1 Downloading The Firmware To download the latest firmware file from the Internet 1 Go to the Kramer Web site at www kramerelectronics com 2 Navigate to SUPPORT Software Firmware Updates 3 Click on the link of the firmware that applies to your product Download it a
9. 900 000505 REV 3
10. ICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products retur
11. Kramer Electronics Ltd USER MANUAL Model PL 18 Control Port Expander Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 4 Your PL 18 Control Port Expander 5 Connecting the PL 18 Control Port Expander 6 Operating the PL 18 Control Port Expander 7 Technical Specifications 8 PL 18 Commands in Protocol 3000 8 1 Operating Commands 8 2 Help Commands 8 3 Result and Error Codes 8 4 Identification Commands 8 5 Machine Information Commands 8 6 Reset Command 9 Protocol 3000 Syntax 9 1 RS 232 2 Settings 9 2 Host Message Format 9 2 1 Simple Command 9 2 2 Command String 9 3 Device Message Format 9 3 1 Device Long Response 9 4 COMMAND TERMS 9 5 Entering Commands 9 6 Command Forms 9 7 Command Chaining 9 8 Maximum String Length 9 9 Backward Support 10 Using the P3K Wizard 10 1 Updating the PL 18 Firmware 10 1 1 Downloading The Firmware 10 1 2 Connecting a PC to the PL 18 10 1 3 Updating the Firmware 10 2 Changing the Device Parameters COONAN NDA wn FW NY e e e e i oe M a NNNN Nene TOTO CO COSo O OO wl N e e j O APULU Contents Figures Figure 1 PL 18 Control Port Expander Figure 2 Connecting the PL 18 Control Port Expander Figure 3 P3K Wizard Screen Figure 4 Connect Serial USB Figure 5 Error Message Figure 6 Device Selection Figure 7 Open File Window Figure 8 Device and File Selected Figure 9 Warning Window Figure 10 Load
12. e Firmware file box The Open File window opens 16 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the P3K Wizard Look in Fw version 1615 i DjPL_18_1615_210509 hex L gt PL_18_BOOT_LOADER hex My Recent Documents e Desktop My Documents 39 My Computer a File name PL_18_1615_210503 hex My Network Files of type Firmware Files hex kfw kbn Figure 7 Open File Window Navigate to the folder containing the firmware file for example C Program Files Kramer Flash Select the firmware file you downloaded in section 10 1 1 and click Open The firmware file appears in the Firmware file box 17 Using the P3K Wizard M pak wizard ae Help Dincerrect Please Select Your Device For Upgrade Load Upgrade Frmwue Please select the device tor upgrade Furmore tie Gae TO o 0 0 PAPL_IBFW verson 1615 PL_18_1615_ 210509 hex CS a aaa a Fiveweaie 00 09 00 1750 Buld Date E OHCP Enabled Stat Upgrade Figure 8 Device and File Selected 9 Click the Start Upgrade button to begin the file transfer The Warning window appears P3K Wizard Warning You are going to upgrade your device firmware and at the end of this process your device will be restarted Are you sure Figure 9 Warning Window 10 Click Yes to continue Load Progress appears in the bottom box 18 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the P3K Wizard Figure 10 Load
13. er Description PORT_NUM 1 to 4 STATE Relay state 0 or close to close the relay 1 or open to open the relay Generic Binary Port Configuration Command Config binary port PORT_NUM IR 1 or Figure 1 ISTOP_BITS 1 or2 ISTART_TOKEN CR IEND_TOKEN CBIN PORT_TYPE CBIN PORT_TYPE PORT_NUM PORT_NUMI CFG_VAL1 CEG_VAL1 CFG_VAL2 CFG_VALS CFG_VAL4 CFG_VAL4 I CFG_VAL5 CFG_VALS CFG_VALE CFG_VALE I CFG_VAL7 CFG_VAL7 CFG_VAL8 CFG_VAL8 CEG_VALA2Il CFG_VAL3 PORT_TYPE UART ETH IR 2 UART 1 RS 232 1 The port number is written over the physical port see BAUD 1200 2400 4800 9600 19200 38400 57600 115200 DATA_BITS 5 to 8 inclusive PARITY NONE ODD EVEN MARK SPACE or first letter of those words DUTY_CYCLE 1 to 99 inclusive followed by that is 2 bytes in hex representation 0x0D and 0x5B 1 CBIN is a generic command thus CFG_VAL parameters are a generic representation of the specific configuration parameters for instance CFG_VAL1 and CFG_VAL2 represent CARRIER_FREQ and DUTY respectively in case PORT_TYPE IR PL 18 Commands in Protoc
14. llows Connect RELAYS 1 and 2 to window blinds Connect RELAYS 3 and 4 to a screen 3 Connect the IROUTPUTS as follows Connect IR OUTPUT 1 toa DVD Connect IR OUTPUT 2 to a display RC Device Screen DVD Display Projector Figure 2 Connecting the PL 18 Control Port Expander 1 Switch OFF the power on each device before connecting it to your PL 18 After connecting your PL 18 switch on its power and then switch on the power on each device 2 On each 3 pole terminal block connector connect either C to NO or C to NC C is common NO is normally open and NC is normally closed 5 Operating the PL 18 Control Port Expander Operating the PL 18 Control Port Expander The PL 18 is typically used to expand the number of ports available to an RC series remote control device The combined RC and PL 18 are configured from the RC device using RC SV software that can be downloaded from the Kramer Web site The PL 18 can also be operated directly from a PC touch screen system or other serial controller using the serial commands of Kramer s Protocol 3000 For an explanation of all control commands see section 9 In addition to operating the PL 18 machine software can be upgraded and device parameters can be accessed and changed using P3K Wizard software also available from the Kramer Web site see section 10 Technical Specifications The PL 18 technical specifications are shown in Table 2 Table
15. nd save it to your disk 4 Extract the file to a folder for example C Program Files Kramer Flash 10 1 2 Connecting a PC to the PL 18 To connect a PC to the PL 18 e Connect a serial cable from an RS 232 9 pin D sub rear panel port on the PC to the RS 232 2 port of the PL 18 as explained in section 5 or e Connect a USB cable from a USB port on the PC to the USB port on the PL 18 1 www kramerelectronics com 2 You cannot upgrade the firmware of the PL 18 through an RC connection The PL 18 must be connected directly to a PC 3 The files indicated in this section are given as an example only File names are liable to change from time to time 13 Using the P3K Wizard 10 1 3 Updating the Firmware To update the firmware perform the following steps 1 Open the Kramer P3K Wizard by double clicking the desktop icon P3K Wizard The P3K Wizard screen appears px Wizard Pheare connect to your device Figure 3 P3K Wizard Screen 2 Click the Connect button The Connect Window appears Note The PL 18 does not have an Ethernet interface Do not select any of the Ethernet options on the Connect window 1 You can download and install the latest version of the P3K Wizard from www kramerelectronics com 2 The screens appearing in this manual are examples of the process The actual screens may differ in their content 14 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the P3K Wizard Connec
16. ne name NAME NAME MACHINE_NAME Reset machine name to NAME RST NAME RST MACHINE_FACTORY_NAME factory default RESULT Visual identification IDV DV OK Note The machine name is not the same as the model name The machine name is used to identify a specific machine or a network in use with DNS feature on MACHINE_NAME Up to 14 alphameric chars Machine factory name Model name last 4 digits from serial number Protocol 3000 Syntax 8 5 Machine Information Commands Command Syntax Response Execute firmware upgrade UPGRADE UPGRADE OK Firmware usually uploads to a device via a command like LDFW The device may need to be reset to complete the process Reset to factory default FACTORY FACTORY RESULT configuration 8 6 Reset Command Command Syntax Response Reset device RESET RESET OK 9 Protocol 3000 Syntax Protocol 3000 is used to control the PL 18 via the RS 232 2 connection using an RC type controller or a PC touch screen other serial controller 9 1 RS 232 2 Settings Port RS 232 2 Baud Rate 115 200 Data Bits 8 Stop Bits 1 Parity None Command Format ASCII 9 2 Host Message Format Start Address optional Body Delimiter Destination _id Message ICRI 9 2 1 Simple Command Command string with only one command without addressing Start Body Delimiter Command SP Parameter_1 Parameter_2 ICRI 9 2 2 Command String
17. ned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION amp Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 21 For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2
18. nty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERV
19. ol 3000 Explicit Binary Port Configuration Command Config Serial port UART CFG PORT_NUM BAUD UART CFG PORT_NUM BAUD pore DATA_BITS PARITY STOP_BITS DATA_BITS PARITY STOP_BITS FLOW_CONTROL FLOW_CONTROL RESULT Config IR out port IR CFG PORT_NUM IR CFG PORT_NUM CARRIER_FREQ DUTY_CYCLE CARRIER_FREQ DUTY RESULT Binary Data Send Receive Emit raw data via a BIN PORT_TYPE PORT_NUM BIN PORT_TYPE PORT_NUM i fi ji o igured binay RAW DATA SIZE BTART_TOKEN RAW_DATA_SiZE RESULT RAW_DATA END_TOKEN Convey raw data RBIN PORT_TYPE PORT_NUM RBIN PORT_TYPE PORT_NUM received tnrough a RAW_DATA Size START_TOKEN RAW_DATA Size RESULT4 preconfigured binary RAW_DATA_SIZE START_TOKEN I S port RAW_DATA END_TOKEN Factory default values of binary ports IR1 IR2 Carrier frequency 38000 duty cycle 33 RS 232 1 9600 baud 8 data bits parity NONE 1 stop bit Configuration and Operation Examples A binary port must be configured properly before using it to send or receive binary data The port may be used in static or dynamic port scenarios Static binary port scenario A specific binary port controls one specific external de
20. t Connection method Ethemet Serial USB Select Port Figure 4 Connect Serial USB 3 To upgrade using an RS 232 or USB connection click Serial USB see Figure 4 Click the drop down box to show the COM ports Select a COM port to connect from COM 1 to COM 13 and click OK Note If you try to connect to a device and it does not respond the following error message appears Click OK Verify that the device is powered on the cable connection is good and that you are trying to connect by the correct method Do not operate the PROGRAM switch on the back panel It is for factory use only P3K Wizard Device is not answering Figure 5 Error Message 15 Using the P3K Wizard 4 After pressing OK on the Connect Window the wizard searches the line for connected devices All detected devices are displayed in the device list box under Please select the device for update Note In the Device Properties section you can update any of the active fields that have a white background After making any changes click Set Please Select Your Device For Upgrade Loss Upgrade Famme Please select the device for upgrade Semad Nurnbes UDP kocsi Pon TCP bca poa KNetiO iP 00 03 00 1780 Bubi Date E DHCP Enabled Stat Upgrade Figure 6 Device Selection 5 Inthe device list box click to select the target device Next select the firmware file to upgrade by clicking Browse next to th
21. vice e g one RC button opens a projector another RC button closes it using the same serial binary port The port is configured only once at installation and the value is stored in the non volatile memory of the PL 18 Thereafter when the RC button is pressed it only invokes the configured BIN commands on the PL 18 Dynamic binary port scenario A specific binary port controls various external devices e g one RC button opens a TV another RC button opens a DVD and both use the same IR binary port with a dual IR emitter cable The binary port must be reconfigured before issuing the BIN command to a different device At each RC button press a CBIN command is sent to the PL 18 before sending a BIN command Binary port configuration examples Configure UART RS 232 port 1 with 9600 8 n 1 serial port configuration parameters cbin uart 1 9600 8 n 1 lt CR gt or uart cfg 1 9600 8 n 1 lt CR gt Configure IR port 2 with 38000 33 as infrared configuration parameters cbin ir 2 38000 33 lt CR gt or ir cfg 2 38000 33 lt CR gt 1 As opposed to any other P3000 command CR cannot be added after the END_TOKEN 2 The RC responds with this command 8 KRAMER SIMPLE CREATIVE TECHNOLOGY PL 18 Commands in Protocol 3000 Using the binary port to send binary data Emit via serial port 1 four bytes the binary representation of P2000 all in 2 serial command bin uart 1 4 lt CR gt
22. vices for example projectors on RS 232 1 One bi directional port for receiving control commands from a PC touch screen other serial controller or an RC series device on RS 232 2 Four relays for the simplified and centralized control of room functions such as lighting closing blinds screen settings and so on Two IR output ports for IR control A USB port for firmware upgrade To achieve the best performance Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer PL 18 away from moisture excessive sunlight and dust H No operator serviceable parts inside unit Warning alee Use only the Kramer Electronics input power wall None ee that is provided with the unit Warning Disconnect power and unplug unit from wall before installing or removing the device or servicing unit 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com Your PL 18 Control Port Expander 4 Your PL 18 Control Port Expander Figure 1 and Table 1 define PL 18 TITT Control Port Expandar PL 18
23. witchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1 Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the inputs and outputs see section 5 Connect the relays 2 Connect the IR outputs Connect the RS 232 RC Device Screen Display Projector Step 2 Power ON the unit Step 3 Operate the machine see section 6 Operate via the RC remote control device and R5 232 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview The PL 18 is a highly versatile port expander that adds RS 232 IR and relay ports to an RS 232 controller especially a Kramer RC device such as RC 2 RC 2C or RC 62 RC 63 It acts as an all in one extended remote control panel for control of A V equipment especially projectors and associated equipment in any room such as classrooms boardrooms or auditoriums The PL 18 Control Port Expander features One bi directional serial port for controlling RS 232 based de
Download Pdf Manuals
Related Search