InView Marquee Message Display
Contents
1. 5 p m EST Outside United Please contact your local Rockwell Automation representative for any States technical support issues New Product Satisfaction Return Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility However if your product is not functioning and needs to be returned follow these procedures United States Contact your distributor You must provide a Customer Support case number call the phone number above to obtain one to your distributor in order to complete the return process Outside United Please contact your local Rockwell Automation representative for the return States procedure InView Allen Bradley Rockwell Automation and TechConnect are trademarks of Rockwell Automation Inc Trademarks not belonging to Rockwell Automation are property of their respective companies www rockwellautomation com Power Control and Information Solutions Headquarters Americas Rockwell Automation 1201 South Second Street Milwaukee WI 53204 2496 USA Tel 1 414 382 2000 Fax 1 414 382 4444 Europe Middle East Africa Rockwell Automation Vorstlaan Boulevard du Souverain 36 1170 Brussels Belgium Tel 32 2 663 0600 Fax 32 2 663 0640 Asia Pacific Rockwell Automation Level 14 Core F Cyberport 3 100 Cyberport Road Hong Kong Tel 852 2887 4788 Fax 852 2508 1846 Publication 2706 INO16D EN P February 2009 PN 398962. e S assurer que l environnement est class non dangereux avant de changer les piles This product contains a lithium battery catalog number 2711P RY2032 There is a danger of explosion if it is incorrectly replaced Replace only with the indicated type Do not replace the battery unless the area is known to be nonhazardous Do not dispose of the battery in a fire or incinerator Dispose of used batteries in accordance with local disposal regulations Publication 2706 INO16D EN P February 2009 InView Marquee Message Display 5 Catalog Number Explanation 2706 P92C Bulletin Number Display Height Display Length es Color max character height Large Marquee P InVi C Tri color de ie eee 9 9 in 228 6 mm 2 Short Case appx arquee SIspay max display character 0 91 m 3 ft with Std LED Pitch 4 Long Case appx 1 83 m 6 ft with Std LED Pitch Publication 2706 IN016D EN P February 2009 6 InView Marquee Message Display Mount the 2706 P92C and 2706 P94C Displays 1 Attach the two sign brackets to a wall ceiling or other surface Be sure to place the brackets so the bracket flanges face appropriately as shown below Mount the brackets the following distance apart measured from the center of the mounting holes in each bracket Mounted so flanges are hidden Mounted so flanges show on the behind the sign sides of the sign 2706 P92C 103 0 cm 40 55 in 2706
3. Mixture of red green and amber characters and spaces Additional Information Usage Typical display load for most message types For additional information on communication port wiring and display configuration refer to the InView Marquee Message Display User Manual publication 2706 UM016 Publication 2706 INO16D EN P February 2009 InView Marquee Message Display 19 Notes Publication 2706 INO16D EN P February 2009 Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products At http support rockwellautomation com you can find technical manuals a knowledge base of FAQs technical and application notes sample code and links to software service packs and a MySupport feature that you can customize to make the best use of these tools For an additional level of technical phone support for installation configuration and troubleshooting we offer TechConnect support programs For more information contact your local distributor or Rockwell Automation representative or visit http support rockwellautomation com Installation Assistance If you experience a problem within the first 24 hours of installation please review the information that s contained in this manual You can also contact a special Customer Support number for initial help in getting your product up and running United States 1 440 646 3434 Monday Friday 8 a m
4. 137 m 450 ft Electrical and Environmental Input voltage 100 240V AC 50 60 Hz Temperature operating 0 50 C 32 122 F Humidity 5 95 noncondensing Ratings Designed to meet UL types 12 and 13 Designed to meet NEMA 4 Hose Down requirements Certifications cULus CE and C Tick Enclosure weight approx 32 kg 70 Ibs 54 4 kg 120 Ibs Enclosure dimensions WxDxH 1 Display is available in short format 105 x 13 x 40 cm 41 14 x 5 25 x 15 9 in 1 0 91 m 3 ft 2 Display is available in long format 1 83 m 6 ft 196 x 13 x 40 cm 77 2 x 5 25 x 15 9 in Publication 2706 INO16D EN P February 2009 18 InView Marquee Message Display Input Current Requirements for 2706 P92C and 2706 P94C Line Voltage Frequency Hz 100 Display 50 Display Load 25 Display Load VAC Load Amp Amp Amp 100 P92C 50 60 3 6 2 1 3 100 P94C 50 60 7 1 3 9 2 3 120 P92C 50 60 29 17 0 120 P94C 50 60 5 8 3 2 9 240 P92C 50 60 14 0 9 0 6 240 P94C 50 60 2 8 1 6 0 Display Load 100 Condition All display pixels are lit in amber Usage Highly unlikely use this value for sizing input power circuit 50 Condition 50 of the display lit in amber screen full of 32 pixel amber B s Usage Unlikely not a typical display condition may be seen with use of bitmaps 25 Condition
5. Supersedes Publication 2706 IN016C MU P April 2004 Copyright 2009 Rockwell Automation Inc All rights reserved Printed in the U S A
6. be responsible or liable for indirect or consequential damages resulting from the use or applicati The examples and diagrams in thi variables and requirements assoc on of this equipment s manual are included solely for illustrative purposes Because of the many iated with any particular installation Rockwell Automation Inc cannot assume responsibility or liability for actual use based on the examples and diagrams No patent liability is assumed by Rockwell Automation Inc with respect to use of information circuits equipment or software described in this manual Reproduction of the contents of this manual in whole or in part without written permission of Rockwell Automation Inc is prohibited Throughout this manual when necessary we use notes to make you aware of safety considerations Identifies i a hazardo nformation about practices or circumstances that can cause an explosion in s environment which may lead to personal injury or death property damage or economic loss IMPORTANT Identifies information that is critical for successful application and understanding of the product ATTENTION Identifies i nformation about practices or circumstances that can lead to personal injury or death property damage or economic loss Attentions help you identify a hazard avoid a hazard and recognize the consequences SHOCK HAZARD Labels may be on or inside the equipment for
7. P92C 107 8 cm 43 22 in 2706 P94C 194 4 cm 76 55 in 2706 P94C 201 2 cm 79 22 in ceiling j 1 T Dr a Sign brackets facing out from the sign Sign brackets facing in behind the sign l Wall or 1 K 7 x IMPORTANT Do not install the sign directly to drywall or plasterboard The sign must be fastened to a surface capable of supporting at least four times the weight of the sign 2 Mount the sign on the sign brackets using the hex bolts supplied Insert the bolts into the far single holes first until the desired viewing angle is determined 5 40 344 x 688 344 x 688 gt 5 40 4 0B ROUND OB ROUND ao 0 0572 0 572 0 lis 344x 688 344 x 688 1 75 1 75 nip OBROUND OB ROUND Sun 88 Z 9 281 Piso 0 i 1 50 4 63 463 p 1 50 w 135 7 635 33 33 7 635 Left Bracket Right Bracket ee lt lt _ Wall Hex Bolt for Single Hole Publication 2706 INO16D EN P February 2009 InView Marquee Message Display 7 3 Tilt the sign to select a viewing angle To hold the sign in place inset the remaining bolts into the desired viewing angle hole on each bracket Ceiling lt Wall End View Wall Ceiling yO Mounted Desired Viewing DA Angle Hole TIP Keep a minimum 2 54 cm 1 0 in clearance on all sides of the sign for ad
8. Power Connection Communication Front View open Opening Terminal Block Opening PRE I o o Ju SZ le i 2 Feed electrical cable through 1 2 water tight conduit the outside end of the connector supplied the electrical opening in the sign case and then through the inside end of the connector Screw the inside and outside ends of the connector together until water tight fl 0 TIP Use either of the two holes nearest the power connection terminal block Publication 2706 IN016D EN P February 2009 InView Marquee Message Display 9 Rubber Gasket Front View a Conduit Connector Sign Case Outside End inside Connector nut with teeth facing the sign case 3 Strip the electrical wires back 1 4 Insert the wires into the appropriate terminal connection and tighten the screw to 0 79 Nem 7 Ibein The terminal block is UL rated for wire ranges of 14 to 8 AWG i Ground Line GREEN Neutral Hot w Line 2 BLACK Yellow WHITE Power connection 4 Remove the necessary hole plugs before connecting the communications cables Publication 2706 INO16D EN P February 2009 10 InView Marquee Message Display 5 Connect the incoming communication wires per the tables below ATTENTION PRG Ethernet cable Shielded
9. Switch 1 Switch 1 is used to configure the display RS485 echo enable baud rate settings and display size e Position 1 enables or disables the echo function Enabling the RS485 echo function allows any packets that come in on COM 0 download RJ 12 port COM 1 RS 232 TB3 port and the Ethernet TCP IP port to be sent out the RS485 port This allows Ethernet TCP IP and other communication protocols to be converted to RS485 by a single P92 or P94 and then sent out to multiple RS485 networked displays TIP Only enable the echo function on one P9x display e Positions 3 and 4 set the baud rate See page 13 for default positions If both switches are off the baud rate can be set via the InView Messaging software The dip switches take priority over the software setting If the baud rate is set to 19 200 using the software positions 3 and 4 set to off and then set to 9600 using switch 1 position 3 on and 4 off the baud rate would then be 9600 Also once positions 3 and 4 are used to set the baud rate and then they are switched off the baud rate setting will remain until it is changed by software or a different dip switch setting e Position 5 is used to set the display size This is set by the factory e Position 6 is used to turn on diagnostics e Position 7 disables download message Publication 2706 INO16D EN P February 2009 InView Marquee Message Display 13 Switch 2 Switch 2 is used to set the serial address
10. of the display Position 1 is the LSB of the address and position 8 is the MSB of the address e If position 1 is on and all other positions are off the display address will be 1 e If position 8 is on and all other positions are off the display address will be 128 e If all positions are set to off the serial address can be set using the InView Messaging software The dip switch setting takes priority over the software setting If the serial address is set to 2 using the software all the dip switches set to off and then switch 2 is used to set the serial address to 3 position 1 and 2 set to on and the remaining positions set to off the serial address will then be 3 Also once Switch 2 is used to set the serial address and then all switch positions are set to off the serial address setting remains until it is changed by software or the dip switch is set 2 1234 5 6 7 8 1 S ON OFF 1 4 1 8 2 3 5 6 ON OFF Not LSB MSB RS485 Used Not Used Echo Size Display Address ON P92C ON Disable OFF P94C Download Message y y swith 1 2 3 Ta 5 fe I7 fe Baud Rate pa P Value 1 2 4 8 16 32 64 128 3 4 iagnostics OFF OFF Software Default ON OFF 9600 OFF ON 19200 ON ON 38400 Legacy Communications Board Kit There is an optional Legacy Communications Board Kit available for the P9 series displays There are a total of six board kits Remote I O DH DH 485 ControlNet DeviceNet and
11. EtherNet IP The Legacy Communications Board Kit converts the six protocols to RS 232 The board kit mounts on the four PEM spacers that are Publication 2706 INO16D EN P February 2009 14 InView Marquee Message Display attached to the internal mounting plate See publication 2706 IN015 for more information on how to install the board kit PEM Spacers i Oy Y i Edo Gh Compact Flash Card This product uses a Type I Compact Flash Card for message file storage 2706 P9x Temperature Protection InView P92C and P94C signs have automatic temperature controls that help to protect the sign from damage when the internal temperature of the sign is too hot to continue normal operation e If the internal temperature of the sign reaches a pre determined dimming point the LED output from the sign is forced into a 50 percent reduced power mode effectively dimming the brightness of LED output by about 50 percent e If the internal temperature of the sign continues to increase another sensing circuit will execute an automatic shut down to protect the sign from damage The LED output from the sign is turned off Two LED pixels will flash in the lower right corner indicating an auto shutdown has occurred e The dimming and shutdown points are listed in the table below Once the temperature drops below the auto shutdown threshold the LED output i
12. Ethernet cable is required to maintain noise The 2706 P Cable1 is used for downloading messages only and must be removed after downloading is complete TB2 is used for supplying power to the optional InView Legacy Communication board kit e i Communication Ethernet TB1 Openings TB1 RS 485 1 GND 4 CH 2 SHLD 5 CHB 3 COMM 6 TERM TB2 Aux 5V 145V 2 GND TB3 RS 232 1 TXD 4 CTS 2 RXD 5 GND 3RTS 6 EGND Publication 2706 INO16D EN P February 2009 InView Marquee Message Display 11 Ethernet RJ 45 1 TD 5 NC 2 TD 6 RD 3 RD 7 NC 4 NC 8 NC 1 Use shielded Ethernet cable to maintain noise immunity Download Port RJ 12 1 1 Aux 5V 4 RX 2 NC 5 NC 3 TX 6 GND 1 The 2706 PCable1 is used for downloading messages only and must be removed after downloading is complete 6 Carefully close the front of the sign case and turn the half turn latches to the right with a large screwdriver Publication 2706 INO16D EN P February 2009 12 _InView Marquee Message Display Dip Switch Information There are two dip switches located on the controller board Switch 1 and Switch 2 lot an Switch swith
13. Installation Instructions InView Marquee Message Display Catalog Numbers 2706 P92C 2706 P94C Topic Page Important User Information 2 Wiring and Safety Guidelines 3 Hazardous Location Considerations 4 Catalog Number Explanation 5 ount the 2706 P92C and 2706 P94C Displays 6 Back to back Mounting 7 Connect the 2706 P92C and 2706 P94C Displays 8 Dip Switch Information 12 Additional Information 18 Legacy Communications Board Kit 13 Compact Flash Card 14 2706 P9x Temperature Protection 14 Replace the Battery in the InView Message Displays 15 Specifications 17 Rockwell ALLEN BRADLEY ROCKWELL SOFTWARE Automation 2 InView Marquee Message Display Important User Information Solid state equipment has operati onal characteristics differing from those of electromechanical equipment Safety Guidelines for the Application Installation and Maintenance of Solid State Controls Publication SGI 1 1 available from your local Rockwell Automation sales office or online at http literature rockwellautomati on com describes some important differences between solid state equipment and hard wired electromechanical devices Because of this difference and also because of the wide variety of uses for solid state equipment all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable In no event will Rockwell Automation Inc
14. equate ventilation Back to back Mounting 1 Attach the brackets to the sign in the ceiling mount position Use the hex bolts supplied Attach chains here Fa First co mam Sign b First Second Mounting Mounting Bracket Bracket 2 Match the signs together back to back Connect them together using a total of six 5 16 bolts and nuts not supplied 3 Use chains not supplied to hang the signs from the ceiling Attach the chains to the top mounting holes of the bracket TIP Use chains capable of supporting 4 times the total weight of the signs Publication 2706 IN016D EN P February 2009 8 InView Marquee Message Display Connect the 2706 P92C and 2706 P94C Displays WARNING HAZARDOUS VOLTAGE e Contact with high voltage may cause death or serious injury Always disconnect power to sign prior to servicing e Maintain Separation of circuits Route the incoming power directly to the power connection terminal block e Do not run the power wiring over the logic board or optional Legacy Communication board 1 Open the front of the sign case by turning the half turn latches to the left with a large screwdriver On the 2706 P92C there are 3 half turn latches on the 2706 P94C there are 5 Carefully let the front of the case drop forward Front View closed Q Half turn Latches on an 2706 P94C Sign Electrical
15. example a drive or motor to alert people that dangerous voltage may be present BURN HAZARD PEPEDEEDE Publication 2706 INO16D EN P Labels may be on or inside the equipment for example a drive or motor to alert people that surfaces may reach dangerous temperatures February 2009 InView Marquee Message Display 3 Wiring and Safety Guidelines Install the InView display conforming to NFPA 70E Electrical Safety Requirements for Employee Workplaces In addition to the NFPA general guidelines refer to the following Careful cable routing helps minimize electrical noise Route incoming power to the module by a separate path from the communication cables TIP Do not run communications wiring and power wiring in the same conduit WARNING SHOCK HAZARD e Maintain separation of circuits Route the incoming power directly to the power connection terminal block e Do not run the power wiring over the logic board or optional Legacy Communication board Where communication and wire paths must cross make their intersection perpendicular Grounding helps limit the effects of noise due to electromagnetic interference EMD To avoid problems caused by EMI properly ground all equipment and use shielded cables IMPORTANT Power wiring must be in accordance with Class Division 2 wiring methods Article 501 4 b of the National Electrical Code NFPA70 and in accordance with the local authority having juri
16. me le code de temp rature le plus d favorable code de temp rature le plus faible peut tre utilis pour d terminer le code de temp rature global du syst me Les combinaisons d quipements dans le syst me sont sujettes inspection par les autorit s locales qualifi es au moment de l installation EXPLOSION HAZARD Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other Substitution of components may impair suitability for Class Division 2 e If this product contains batteries they must only be changed in an area known to be nonhazardous means provided with this product RISQUE D EXPLOSION Couper le courant ou s assurer que l environnement est class non dangereux avant de d brancher l quipement Couper le courant ou s assurer que l environnement est class non dangereux avant de d brancher les connecteurs Fixer tous les connecteurs externes reli s cet quipement l aide de vis loquets coulissants connecteurs filet s ou autres moyens fournis avec ce produit e La substitution de composants peut rendre cet quipement inadapt une utilisation en environnement de Classe Division 2
17. p 3 Carefully lower the door Front View closed a Front View open Half turn Latches on an 2706 P94C Sign z Fr FE a Circuit lO is a F 5 Board cd ON As ws gl er Ey 4 Locate the battery on the circuit board Press down here to pop battery out 5 Press down firmly on the middle part of battery retainer clip The battery will pop out 6 Slide the new battery under the 3 prong holder and push down 7 Raise the door and turn the half turn latches all the way right until they hit the stop and the door is pulled in Publication 2706 IN016D EN P February 2009 InView Marquee Message Display 17 Specifications 2706 P92C 2706 P94C Display Display type LED matrix Tri Color C Display window size 91 4 x 24 4 cm 36 x 9 6 in 182 9 x 24 4 cm 72 x 9 6 in WxH Display array 120 x 32 pixels 240 x 32 pixels Center to center pixel spacing 0 76 cm 0 3 in pitch Number of lines 1 25 Lines of text character height minimum characters per line 1 line 9 6 in 1311 2 line 4 5 in 130 3 line 3 0 in 131 4 line 2 1 in 20 5 line 1 5 in 24 1 line 9 6 in 26 2 2 line 4 5 in 26 3 line 3 0 in 26 4 line 2 1 in 40 5 line 1 5 in 48 Character set Approximate viewing distance Standard and Extended ASCII
18. s turned on at the dimming level Once the temperature drops below the dimming threshold auto dimming is disabled and the LED brightness is back to 100 percent 2706 P92C 55 C 131 F 75 C 167 F 2706 P94C 55 C 131 F 75 C 167 F Publication 2706 INO16D EN P February 2009 InView Marquee Message Display 15 TIP Take into account the effects of ambient temperature when evaluating mounting locations for the sign You should always maintain recommended clearance distances around the sign and avoid poorly ventilated mounting locations that could be subject to radiation convection conduction or other thermal transfer effects Replace the Battery in the InView Message Displays The terminal contains a lithium battery which is intended to be replaced during the life of the product ATTENTION The clock module contains lithium Do not dispose the battery in a fire or incinerator or the clock module may explode Follow disposal regulations in your area for lithium battery disposal At the end of its life the used battery should be collected separately from any unsorted municipal waste and recycled Publication 2706 INO16D EN P February 2009 16 _InView Marquee Message Display Follow these steps to replace the battery in the InView 2706 P92C or 2706 P94C message displays 1 Disconnect power from the message display 2 Turn the half turn latches all the way to the left until they hit the sto
19. sdiction Publication 2706 INO16D EN P February 2009 4 InView Marquee Message Display Hazardous Location Considerations This equipment is suitable for use in Class I Division 2 Groups A B C and D or non hazardous location only The following WARNING statement applies to use in hazardous locations The following information applies when operating this equipment in hazardous locations Products marked CL DIV 2 GP A B C D are suitable for use in Class Division 2 Groups A B C D Hazardous Locations and nonhazardous locations only Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code When combining products within a system the most adverse temperature code lowest T number may be used to help determine the overall temperature code of the system Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation Informations sur l utilisation de cet quipement en environnements dangereux Les produits marqu s CL 1 DIV 2 GP A B C D ne conviennent qu une utilisation en environnements de Classe Division 2 Groupes A B C D dangereux et non dangereux Chaque produit est livr avec des marquages sur sa plaque d identification qui indiquent le code de temp rature pour les environnements dangereux Lorsque plusieurs produits sont combin s dans un syst
Download Pdf Manuals
Related Search