User`s Manual Template
Contents
1. Motor Output and Step Dir Motor Under Pulley Ratios set the pulley ratios of the machine Engine Configuration Ports Port Setup and Axis Selection Motor Outputs Input Signals Output Signals Encoder MPG es Motor Control Special Functions 5 Use Spindle Motor Output f Use Spindle Feedback in Sync Modes I Step Dir Motor P amt mm oS Spindle Sp jA gi Disable Flood Mist relays Delay Mist M7 Output B 0 Flood M8 Output a jo CW Delay Spin UP M Seconds Output Signal s 1 6 CCW Delay Spin UP 1 Seconds ModBus Spindle Use Step Dir as well EW Delay Spind DOWN Seconds Enabled Reg 64 64 127 CCW Delay Spin DOWN f Seconds Max ADC Count Immediate Relay off before delay Special Options Usually Off T HotWire Heat for Jog l Laser Mode freq Torch Volts Control Torch Auto OF 5 Go to Config Motor Tuning Spindle On Steps per unit put 1 000 set velocity to maximum For Acceleration choose the acceleration that you feel comfortable with Start slow increase acceleration as you test your system Under Step Pulse length use a number from 3 to 5 but start with 3 This number is directly proportional to the final voltage you will get in the analog output Use this number and the fine tuning pot to adjust the voltage you want to get at max speed User s Manual Page 7 Motor Tuning and Setup Axis Selecton SPINDLE MOTOR MOVEMENT PROFILE Velocity inches per Mi2. Line Neutral GNO Line Neutral GNO C NCarc Integration Solutions for CNC Projects PRODUCT INTEGRATION INSTRUCTIONS Connection C61 with C11 MARCH 2015 Diagram connection of the C61 with the C11 24 1200C g m POWER w fe SUPPLY SREEN NOT USED mn BLUE RELI MLO SUPPL Y POHER 240C SUPPLY POHER BVOC a if r User s Manual GND Neutral Page i WARNING Electrical shock or serious physical injury could result due to misuse Control BOX Disconnect power cables while installing the Control Box Read and follow instructions on the manual Images below show the step required to install the kit into the XMT control box 1 1 Step 1 Remove the bottom cover of the controller box 1 2 Step 2 Remove all connections between the manual control panel and the control box User s Manual Page 1 1 3 Step 3 Install the C61 over the mounting holes of the box 2 o z 8 We ET 1 4 Step 4 Insert the AC cord cable receptacles to the AC input terminals of the C61 Note Connect to the C61 only the neutral and line terminal User s Manual Page 2 1 5 Step 5 Connect the black and white 16 AWG cable provided in the kit from the C61 AC output terminal to the AC terminals of the motherboard incluided inside the XMT box 1 6 Step 6 Connect the 5 wires cable provided in our kit from the C61 to terminals of the daugtherboard incluided insi
3. de the XMT box User s Manual Page 3 1 7 Step 7 Insert an standar RJ45 cable through the slot of one side of the control box and plug the cable in the RJ45 connector located in the C61 board User s Manual Page 4 1 8 Step 8 Connect the other side of the RJ45 cable to the terminal of the C11 board 5 E WHITE eG i ah fa Line Neutral GNO 2 CONFIGURING THE VARIABLE SPEED CONTROL PIN 14 OF THE C11 This function lets you control your XMT KIT with PWM and REV signals as if it was an axis motor The C11 board converts the PWM into an analog 0 10VDC 2 1 Configuring the Control Software 1 Go to Config Ports amp Pins Motor Outputs Enable the spindle and select the port and pins you wired for step and direction User s Manual Page 5 Engine Configuration Ports Port Setup and Axis Selection tetcroauts rou Signals Output Signals Encoder MPG s Spindle Setup Mill Options Enabled Step Pint Dir Pin Dir LowActi Step Low A Step Port 2 3 af 1 4 j 1 Engine Configuration Ports Port Setup and Axis Selection Motor Outputs Input Signals Pin Number Active Low Digit Trig Enable Qup e O U a ee Seve 5 71 1E Pins 2 9 1 14 16 and 17 are output pins No other pin numbers should be used RERRRRRARRR User s Manual Dir Port Page 6 3 Go to Config Ports amp Pins Spindle Setup In the motor control box check Use Spindle
4. nute 150 Accel Velocty Steps per In s or mm s per min 1000 1500 Disclaimer Use caution CNC machines could be dangerous machines DUNCAN USA LLC or Arturo Duncan are not liable for any accidents resulting from the improper use of these devices This Kit is not fail safe device and it should not be used in life support systems or in other devices where its failure or possible erratic operation could cause property damage bodily injury or loss of life User s Manual Page 8
Download Pdf Manuals
Related Search