VAP2500 Wireless Access Point Quick Start Guide
Contents
1. transmitter Firmware setting is not accessible by the end user FCC DECLARATION OF CONFORMITY Motorola Inc Broadband Communications Sector 101 Tournament Drive Horsham PA 19044 1 215 323 1000 declares under sole responsibility that the VAP2500 complies with 47 CFR Parts 2 and 15 of the FCC Rules as Class B digital devices These devices comply with Part 15 of FCC Rules Operation of these devices is subject to the following two conditions 1 These devices may not cause harmful interference and 2 these devices must accept any interference that may cause undesired operation WIRELESS LAN INFORMATION The VAP2500 products are wireless network products that use Orthogonal freguency division multiplexing OFDM radio technology These products are designed to be inter operable with any other wireless OFDM type product that complies with e The IEEE 802 11 Standard on Wireless LANs Revision A and Revision N as defined and approved by the Institute of Electrical Electronics Engineers e The Wireless Fidelity WiFi certification as defined by the Wi Fi Alliance WIRELESS LAN AND YOUR HEALTH The VAP2500 like other radio devices emit radio frequency electromagnetic energy but operate within the guidelines found in radio frequency safety standards and recommendations RESTRICTIONS ON USE OF WIRELESS DEVICES In some situations or environments the use of wireless devices may be restricted by the proprietor of the building or res2. U verse Wireless Access Point operates on y with authorized U verse Wireless Receiver s FRONT PANEL Paired Power E a Link WPS REAR PANEL Green Power is on Off Power is disconnected from its power source Blinking orange WPS button has been pushed and pairing is in progress solid Green At least one wireless receiver has been paired Flashing Green At least one wireless receiver is paired and wireless activity is detected Off No wireless association Solid Green Ethernet link is detected Blinking Green Ethernet link is detected and wired activity is present Off Ethernet link is not detected WPS button Reset Button Resets the VAP2500 to its default settings Ethernet Connects to the Ethernet equipped U verse Port Residential Gateway Power Connector INSTALLING YOUR WIRELESS ACCESS POINT AND WIRELESS RECEIVER Follow the instructions below to install your Wireless Access Point and Wireless Receiver Before you connect the Access Point ensure the Gateway is powered on Connect one VAP2500 unit to your Residential Gateway using the provided yellow Ethernet cable jito U verse Wireless Receiver r Gateway VAP2500 Wireless Access Point Connect the power adapter to the Access Point and plug it into a wall outlet You will see the units Power and Ethernet LEDs go on Connect the cord from the DC Power Adapter to the POWER connector on the rear of the Receiver and
3. harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by Motorola for compliance could void the user s authority to operate the equipment For operation within 5 15 5 25GHz 5 25 5 35GHz 5 47 5 725GHz frequency range it is restricted to indoor environment The band from 5600 5650MH7z will be disabled by the software during the manufacturing and cannot be changed by the end user This device meets all the other requirements specified in Part 15E Section 15 407 of the FCC Rules IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or
4. plug the adapter into an AC wall outlet and then connect the Receiver to your IV For more details on connecting your Receiver to your TV refer to your TV user manual When power is applied to the Receiver the Power button lights green Ensure that your IV is powered on Once the Receiver powers on wait until a prompt appears on your TV screen asking If you wish to connect On the front panel of the Receiver press and release the OK button Go to the Access Point and press and hold the WPS button for two seconds then release to activate the WPS process The WPS LED will blink orange An icon appears on the TV screen indicating that the connection sequence Is In process When three horizontal dots appear the connection has been successful On the front panel of the Receiver two or more LEDs on the Signal Strength indicator will light green You have now established a secure wireless connection between the Access Point and the Receiver and can begin enjoying U verse service INSTALLING ADDITIONAL WIRELESS RECEIVERS To connect additional Wireless Receivers repeat steps 3 7 above
5. radio transmitter and accordingly have been certified as compliant with 47 CFR Part 15 of the FCC Rules for intentional radiators Products that contain a radio transmitter are labeled with FCC ID and the FCC logo www motorola com ay MOTOROLA and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings LLC All other product or service names are the property of their respective owners 2012 Motorola 9 Mobility LLC All rights reserved No part of this publication may be reproduced in any form or by any means or used to make any derivative work such as translation transformation or adaptation without written ae permission from Motorola Mobility LLC Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change Motorola provides this guide without warranty of any kind implied or expressed including but not limited to the implied warranties of merchantability and fitness for a particular purpose Motorola may make improvements or changes in the product s described in this manual at any time 588457 001 a 07 12 INSTALLATION The VAP2500 enables you to transmit multiple standard and high definition video streams throughout your home wirelessly You can enjoy a full range of video services and applications without having to run wires lay cables or drill holes The
6. SAFETY AND COMPLIANCE WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING DO NOT PLACE OBJECTS FILLED WITH LIQUIDS SUCH AS VASES ON THE UNIT CAUTION TO ENSURE REGULATORY COMPLIANCE USE ONLY THE PROVIDED POWER AND INTERFACE CABLES CAUTION DO NOT OPEN THE UNIT DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL This device must be installed and used in strict accordance with the manufacturer s instructions as described in the user documentation that comes with the product Modifications not approved by Motorola may void the user s authority to operate the device Postpone Wireless Access Point installation until there is no risk of thunderstorm or lightning activity in the area Do not overload outlets or extension cords as this can result in a risk of fire or electric shock Overloaded AC outlets extension cords frayed power cords damaged or cracked wire insulation and broken plugs are dangerous They may result in a shock or fire hazard Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords where they are attached to plugs and convenience receptacles and examine the point where they exit from the product Place this equipment in a
7. hat the customer install an AC surge protector in the AC outlet to which this device is connected This is to avoid damaging the equipment by local lightning strikes and other electrical surges Different types of cord sets may be used for connections to the main supply circuit Use only a main line cord that complies with all applicable product safety requirements of the country of use Installation of this product must be in accordance with national wiring codes Place unit to allow for easy access when disconnecting the power cord adapter of the device from the AC wall outlet Wipe the unit with a clean dry cloth Never use cleaning fluid or similar chemicals Do not spray cleaners directly on the unit or use forced air to remove dust This product was qualified under test conditions that included the use of the supplied cables between system components To be in compliance with regulations the user must use these cables and install them properly Connect the unit to a grounding type AC wall outlet using the power adapter supplied with the unit Do not cover the device or block the airflow to the device with any other objects Keep the device away from excessive heat and humidity and keep the device free from vibration and protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause
8. location that is close enough to an electrical outlet to accommodate the length of the power cord Place this equipment on a stable surface When using this device basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following e Read all of the instructions before you operate this equipment Give particular attention to all safety precautions Retain the instructions for future reference e Comply with all warning and caution statements in the instructions Observe all warning and caution symbols that are affixed to this equipment e Comply with all instructions that accompany this equipment e Avoid using this product during an electrical storm There may be a risk of electric shock from lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the cable system This will prevent damage to the product due to lightning and power surges e Operate this product only from the type of power source indicated on the product s marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company e Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating condition It is recommended t
9. ponsible representatives of the organization For example using wireless equipment in any environment where the risk of interference to other devices or services is perceived or identified as harmful If you are uncertain of the applicable policy for the use of wireless equipment in a specific organization or environment you are encouraged to ask for authorization to use the device prior to turning on the equipment The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this product or the substitution or attachment of connecting cables and equipment other than specified by the manufacturer Correction of interference caused by such unauthorized modification substitution or attachment is the responsibility of the user AT amp T U verse FAIRE WPS VAPeSo0 AT amp T U vers VAP2500 Wireless Access Point Quick Start Guide dust The manufacturer and its authorized resellers or distributors are not liable for any damage or wet l violation of government regulations that may arise from failing to comply with these guidelines a Installation must at all times conform to local regulations FCC COMPLIANCE CLASS B DIGITAL DEVICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable FCC CERTIFICATION The VAP2500 contains a
Download Pdf Manuals
Related Search