KBD9000 Transmitter/ Controller Installation/ Operation Manual
Contents
1. Pelco Manual C551M 4 98 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 6 KBD9000 Dimension Drawing 15 8 0 WARRANTY AND RETURN INFORMATION Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 1998 Pelco All rights reserved 16 WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video2. recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Sixmonthsonallpan andtilts scanners or presetlenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating tothe Products shall not exceed the price paid by the Dealerto Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state Ifa warranty repair is required the Dea
3. See Section 4 2 KBD9000 CONTROLS for more information about each control function 4 1 FUNCTIONAL CIRCUIT DESCRIPTION The basic functional concept of a Coaxitron system feeds 15 control pulses in a re verse direction from the KBD9000 control transmitter to the receiver located near each camera station These control pulses do not interfere with the video monitor presenta tion because they occur during the vertical blanking interval of the video signal Coaxial cable impedance matching is assured by the video amplifier in the control receiver Proper receiving and termination impedance is likewise assured by the terminating resistor in the KBD9000 control transmitter Any equipment placed be tween the remote and local locations must be of the loop through or bridging type line amplifiers cannot be tolerated Response time of the system is normally less than 30 ms Error detection circuitry is incorporated to immunize the system from externally generated noise Under extremely adverse environmental noise conditions response time may increase and control functions can fail Under such extreme conditions however provision is made to inhibit all momentary functions The proper function of the Coaxitron system depends on the compatibility of two signals simultaneously traveling in opposite directions in the same coaxial cable If the control signal is made large compared to the video signal there is the risk that associated e
4. send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco Manual C551M 4 98
5. KBD9000 Transmitter Controller Installation Operation Manual C551M 4 98 Pelco 3500 Pelco Way Clovis e CA 93612 5699 USA e www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 CONTENTS Section Page AO GENERAL ariana 3 1 1 IMPORTANT SAFEGUARDS AND WARNINGS m 1 2 REGULATORY NOTICES n 4 1 8 UNPACKING INSTRUCTIONS i 4 2 0 DESCRIPIION sail nia i 5 23 MODELS 3 25 26 a itt nus n tte nin dif hte eur 6 2 2 CERTIFICATIONS nen eene nemen nennen nnn nnne nnn 6 3 0 INSTAELATION icai rra tr a 7 3 1 POWER sd 3 2 VIDEO INPUT af 3 8 VIDEO OUTPUT wT 3 4 SYSTEM CONFIGURATIONS i 7 AiO ORR RATO N sts cuc zens rcentaaheceayatavnde Lala 4 1 FUNCTIONAL CIRCUIT DESCRIPTION 4 2 KBD9000 CONTROLS enne eene enhn iners neni 5 0 TROUBLESHOOTING i 13 6 0 MAINTENANCE 510 cmd ecu Cp ors dee re EL S Eh Terza PESE YE EP 14 7 0 SPECIFICATIONS ccccccccssssccsssecessseecessssecessesecsssesessssaeessseeesseeseseeees 15 8 0 WARRANTY AND RETURN INFORMATION 16 LIST OF ILLUSTRATIONS Figure Mai DUIA Ww Basic KBD9000 Configurationi 2 eiae b apte des 8 KBD9000 Configuration with Manual Video Switcher and Multipl
6. NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Please thoroughly familiarize yourself with the information in this manual prior to installation and operation Pelco Manual C551M 4 98 3 1 2 REGULATORY NOTICES NOTE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are de signed to provide reasonable protection against harmful interference in a residen tial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try and cor rect the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 1 3 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully The following items are supplied 1 KBD9000 Tra
7. ail completely with all control functions disabled In order to prevent system failures due to excessively high video levels it is recommended that cameras be powered by the receiver The KBD9000 is designed to combat prolonged loss of control due to the condi tions described previously by providing the following protective functions 1 Simultaneous commands from two different sources are processed to assure that manual iris control cannot be inadvertently selected in place of automatic control 2 Asustained 20 to 40 second illegal command condition results in a camera off b automatic iris or c manual pan These functions greatly reduce the possibility of loss of control and usually elimi nate the need for service 11 As an example assume that the operator switches to manual iris control and pro ceeds to open the iris excessively The result can be a complete loss of control Within 20 to 40 seconds camera power is automatically removed assuming this feature exists and auto iris is reinstated 4 2 KBD9000 CONTROLS Refer to Figure 5 KBD900 Control Buttons to better understand the KBD9000 con trols The KBD9000 has the following controls Camera Power Two push button switches for On Off control latching function Aux 1 2 Two push button switches for latching functions Aux 3 4 Two push button switches for momentary functions Pan Two push button switches for Auto Man pan control latching function Fo
8. cus Two push button switches for Near Far focus control Zoom Two push button switches for Tele Wide zoom control Iris Two push button switches for Open Close iris control Pan Tilt Four push button switches for Pan Tilt control External requirements are needed for operation refer to receiver manual cli CAMERA AUX PAN ON OFF AUTO MAN o Bg 0 838w 0 9 6 Focus IRIS e Bas g FAR CLOSE tJ KBD9000 MADE IN U S A Figure 5 KBD9000 Control Buttons 12 Pelco Manual C551M 4 98 5 0 TROUBLESHOOTING Pelco Manual C551M 4 98 If you experience operating problems with either the receiver or the KBD9000 first check all receiver fuses and voltage readings to make sure they are in working order The Pelco CX900TLC Local Test Board Plug in Module can be utilized to verify that receiver functions and accessories are operational There is little that can be done without the aid of an oscilloscope We recommend you contact your local dealer or our Customer Service Department for assistance 13 6 0 MAINTENANCE 14 The KBD9000 is engineered to provide years of reliable service Regularly sched uled maintenance is not required Clean the outer surface of the KBD9000 with a nonabrasive cleaning cloth and antistatic cleaner Be sure not to get any cleaner inside the KBD9000 case Pelco Manual C551M 4 98 7 0 SPECIFICATIONS ELECTRICAL I
9. d Coaxitron receiver to be controlled Functions such as auto random are latching and will remain on until turned off by the KBD9000 In this configuration the Hi Z 75 ohm Switch on the back of the KBD9000 is set to the 75 ohm position KBD9000 basic interconnections between the KBD9000 and receiver are shown in Figure 3 If you have chosen a configuration that includes a switching device refer to the manual provided with the switcher for the appropriate connections MONITOR TERMINATED VIDEO SIGNAL COAXITRON RECEIVER MULTICONDUCTOR CABLE KBD9000 Figure 1 Basic KBD9000 Configuration MONITOR TERMINATED SIGNAL MULTICONDUCTOR CABLE MANUAL SWITCHER KBD9000 SIGNAL MULTICONDUCTOR CABLE Figure 2 KBD9000 Configuration with Manual Video Switcher and Multiple Cameras Pelco Manual C551M 4 98 RECEIVER VIDEO CABLE RECEIVER INPUT FROM CAMERA RECEIVER VIDEO CABLE OUTPUT TO KBD9000 RECEIVER CONTROL OUTPUT TO PAN AND TILT LENS AMP SERIES CPC OUTPUT CONN 24 120 230 VAC INPUT FROM OUTPUT TO RECEIVER MONITOR Figure 3 Basic KBD9000 Configuration Interconnect Diagram Pelco Manual C551M 4 98 NOTE A but the last KBD9000 transmitter and associate switcher must be looping and unterminated Transmitters and associated switchers should be physically ad Jacent to prevent signal deteriora tion due to cab
10. e Cameras 2 ii dece atr e t eps Basic KBD9000 Configuration Interconnect Diagram KBD9000 Configuration with Multiple Transmitters and Receivers 10 KBD9000 Control B tlons 1 cioe e nett ode 12 KBD9000 Dimension Drawing 2 nonne 15 LIST OF TABLES Table A Video Coaxial Cable Requirements se 7 REVISION HISTORY Manual Date Comments C551M 1 98 Original version 4 98 Added Certifications Deleted Figure 4 Pelco Manual C551M 4 98 1 0 GENERAL 1 1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 Only use replacement parts recommended by Pelco The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit maintenance instructions in the literature accompanying this unit i This symbol indicates that there are important operating and CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER
11. ideo Coaxial Cable Requirements Cable Type RG59 U 750 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum cable requirements 75 ohms impedance All copper center conductor All copper braided shield with 95 braid coverage 3 3 VIDEO OUTPUT Connect a good grade of video coaxial cable from the video OUT BNC connector on the rear panel of the KBD9000 to the video input of the monitor This cable should be terminated in 75 ohms at the monitor or if looped through the monitor terminated at the far end of the run 3 4 SYSTEM CONFIGURATIONS The simplest system configuration utilizing the KBD9000 is shown in Figure 1 Ba sic KBD9000 Configuration This system consists of the KBD9000 control transmit ter coax cable and receiver camera This basic Coaxitron system is flexible and can be expanded to control multiple camera sites when a hard contact switching device is added In this configuration the Hi Z 75 ohm switch on the back of the KBD9000 is set to the 75 ohm position The addition of a manual video switcher and one receiver camera is shown in Figure 2 KBD9000 with Manual Video Switcher and Multiple Cameras In this example the active coaxial cable is terminated in the KBD9000 and the inactive cables are terminated in the switcher The selected camera signal is fed to the KBD9000 which then feeds the monitor When a camera selection is made that video line is dedicated to the KBD9000 and allows the associate
12. le mismatch MONITOR TERMINATED The Figure 4 drawing KBD9000 Configuration with Multiple Transmitter and Re ceivers shows a more complex system In this example multiple KBD9000 trans mitters are controlling multiple receivers Video cables from the receivers are looped through the first control station to the second At the first control station a bridging looping type sequential switcher is used and the Hi Z 75 ohm switch on the back of the KBD9000 is set to the Hi Z position At the second control station a terminating switcher is used and the Hi Z 75 ohm switch on the back of the KBD9000 is set to the 75 ohm position Any one KBD9000 transmitter can assume control If two or more KBD9000 control units are activated simultaneously erroneous responses are prevented by error detection circuitry in the associated receiver I E E VIDEO E Dd SIGNAL LOOPING i COAXITRON SWITCHER RECEIVER MULTICONDUCTOR I i i VIDEO i i SIGNAL i Y TERMINATING i COAXITRON SWITCHER RECEIVER MULTICONDUCTOR i COAXIAL i CABLE MONITOR TERMINATED Figure 4 KBD9000 Configuration with Multiple Transmitters and Receivers 10 Pelco Manual C551M 4 98 4 0 OPERATION Pelco Manual C551M 4 98 In general all operating controls on the KBD9000 are self explanatory
13. ler must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 6 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE
14. nd 16 are momentary that is they are only actuated while the associated control switch on the KBD9000 is operated Functions 11 12 13 and 14 are latching that is camera power auto scan and auto manual iris are latching functions and remain on until turned off The latching iris function is not dedicated and with proper interfacing it can be used for some other latching func tion Alternately AUX 1 2 3 and 4 may be used as momentary functions to control such things as lights or gates with proper external interfacing Up to ten functions can be operated simultaneously Functions 11 through 16 must be used individu ally although any one of these functions may be used simultaneously with func tions 1 through 10 KBD9000 is an improved version of the original Coaxitron transmitter controller Improvements include the following features 1 When used with a Pelco CX900TLC Test Local Control Plug in Module pro vides troubleshooting capability for both the receiver and the KBD9000 2 Panitilt zoom and camera power control are included on the main receiver board which eliminates malfunctions due to incorrect wiring or broken wires KBD9000 provides the following standard functions 1 Pan Tilt 2 Lens Control Zoom iris and focus 3 Camera power on off The KBD9000 does not have preset capabilities but it will work with receivers capable of doing presets 2 1 MODELS KBD9000 Desktop Coaxitron transmitter controller
15. nput Voltage Power Consumption Connectors Input Impedance Control Method Pulse Amplitude Input Video Level System Bandwidth GENERAL Construction Finish Environment Dimensions Weight Rating 12 VAC from a 120 VAC 60 Hz wall transformer provided with unit 230 VAC 50 Hz with KBD9000 X 2 5 vA Two video BNC connectors video input and output 75 ohms or high impedance Hi Z switchable 15 pulse train pulse width modulated superimposed on the video signal duringthe vertical blanking interval by the KBD9000 control transmitter Pulse train occupies 1 TV line period Approximately 1 Vp p added to video signal 333 kHz nominal 1 Vp p nominal 2 Vp p maximum at less than 75 APL 1 5 Vp p maximum at 90 APL Less than 2 dB down at 10 MHz exclusive of cable Aluminum Gray polyester powder coat Indoor 10 to 120 F 23 to 49 C See Figure 6 Unit Shipping 1 95 Ib 0 90 kg 5 0 Ib 2 27 kg approximate NEMA 1 Design and product specifications subject to change without notice This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment 8 10 20 57 clt CAMERA O
16. nsmitter Controller 1 Installation Operation Manual C551M 1 12 VAC Wall Mount Transformer Be sure to save the shipping carton boxes and inserts They are the safest material in which to make future shipments If an item appears to have been damaged in shipment replace it properly in its box and contact the factory at 1 800 289 9100 or 1 559 292 1981 for a replacement International customers fax 1 559 348 1120 for authorization and instructions If an item needs to be returned to the factory for repair consult the WARRANTY AND RETURN section of this manual for instructions Pelco Manual C551M 4 98 2 0 DESCRIPTION Pelco Manual C551M 4 98 The KBD9000 Transmitter Controller is a desk top unit that provides up to 16 re mote control functions It operates without the need for control cables other than for a dedicated video cable for the normal transmission of a remote camera signal to the local monitoring and control position Coaxitron control lends itself to applica tions where short to medium distances are involved and where equalization of cable losses is not required Check your receiver driver manual for active functions Typically control functions are Pan Left Pan Right Tilt Up Tilt Down Zoom In Zoom Out Focus Near Focus Far Iris Open 10 lris Close 11 Camera Power On Off 12 Auto Manual Scan 13 AUX1 14 AUX2 15 AUX3 16 AUX4 o 0 o m Ro m Functions 1 through 10 15 a
17. quipment will be adversely affected If the control signal is made small compared to the video signal it becomes difficult to separate it from the video signal and any incumbent noise or hum Therefore the Coaxitron system is de signed to function with video and control signals nominally equal Under such circumstances reliable performance can be predicted with cable lengths up to 1 500 feet 457 m Beyond this distance the control signal amplitude can become attenuated sufficiently to make performance marginal Marginal performance is also approached if the video signal is allowed to become excessive the dy namic range of the receiver video amplifier is one limitation Sending end distortion produced by the coaxial cable is typically the major contributor to the malfunction ing of a Coaxitron system The amplitude of distortion products is proportional to video signal amplitude and is a nonlinear function of cable length The influence of these distortion products upon system performance is difficult to predict if signal amplitude is allowed to exceed specifications Normally auto iris functions will maintain a video level well within reasonable limits and assure reliable performance Often however automatic or manual level settings may be made abnormally high perhaps to compensate for long cable losses or to produce a picture with more contrast An excessively high video level setting can cause the Coaxitron control system to f
18. with pan amp tilt and zoom lens control 120 VAC input KBD9000 X Same as the KBD9000 except 230 VAC input CE 2 2 CERTIFICATIONS The products identified below have been tested and certified for agency compli ance as noted ma Agency Compliance Certification xw 00x X T_ Applicable CE FCC UL and CSA cUL directives standards e 93 68 EEC CE Mark Directive e 89 336 EEC 92 31 EEC Electromagnetic Compatibility EMC Directives EN 55022 1984 Class B Radio frequency emissions limits e EN 55082 2 1992 Immunity standard EC 801 2 1984 ESD immunity EC 801 3 1984 Radiated field immunity e IEC 801 4 1988 Electrical Transients e 73 23 EEC Low Voltage Directive EMC e EN 60950 Safety of ITE Equipment FCC 47 CFR Part 15 Subpart B Class B Additional applicable standards NEMA Type 1 IP 30 Pelco Manual C551M 4 98 3 0 INSTALLATION NOTE efer to Table A for the type of video coaxial cable to use Pelco Manual C551M 4 98 3 1 POWER No power on off switch is provided To apply power insert the wall mount trans former plug into the 12 VAC power jack in the rear panel and insert the wall mount transformer into a 120 VAC power source 230 VAC with KBD9000 X 3 2 VIDEO INPUT Connect a good grade of video coaxial cable from the Coaxitron receiver or manual video switcher to the video IN BNC connector on the rear panel of the KBD9000 Table A V
Download Pdf Manuals
Related Search