Posey® Bed 8070 Assembly Instructions
Contents
1. Fig 4 K Fig 4 L NOTE Make sure the holes on the posts face inward and towards the center Fig 4 K NOTE Steps 2 5 shown for the Right Head Post will be repeated with each of the 4 posts Assemble each post completely before moving on to the next Posey Bed 8070 Left Foot Post 1 Align the left foot post Part M with the holes on the frame located on the left side foot of the bed Fig 4 N Fig 4 M Fig 4 N NOTE Make sure the holes on the posts face inward and towards the center Fig 4 M NOTE Steps 2 5 shown for the Right Head Post will be repeated with each of the 4 posts Assemble each post completely before moving on to the next Completed head post assembly Fig 4 O Completed foot post assembly Fig 4 P TI Bed Assembly Short Rail Assembly Materials e Hardware Packet A e Part L 2 e 9716 wrench ACAUTION This section requires two people 1 Hold and align one of the short rails Part L between the left and right head posts Parts H amp 1 NOTE Make sure the holes on the posts face inward on both sides of the frame Fig 5 A Hole Direction Inward Fig 5 A 2 Place a locking washer on two 2 1 bolts Hardware Packet A and insert one into the hole facing the inside of the post Fig 5 B Locking Washer Bolt Fig 5 B 3 Hand tighten the bolts loosely until all rails are installed 4 Repeat on the other side of the2. 2 Repeat with the other short foam pad on the other side of the bed Fig 6 A Fig 6 A 3 Open the slot on a long foam pad Part F 2 each and wrap two pads around either long rail Fig 6 B NOTE Make sure that the slot faces outward from the bed frame Fig 6 B 14 Posey 4 Repeat with the other long foam pad on the other side Fig 6 B 5 Open the slot on a long foam pad Part F and wrap around on any of the vertical leg posts Fig 6 C ACAUTION Make sure that the slot faces outward from the bed frame Fig 6 C 6 Repeat on the other three vertical posts until all are padded Posey Bed 8070 Posey Canopy Installation Materials e Part R 1 e Assembled Bed Frame When zipping the canopy make sure the zipper pins are completely seated Failure to do this will prevent the zipper from closing securely which may lead to unassisted bed exit and potential patient injury ACAUTION To avoid damage to zippers or fabric be sure to pull the fabric closed as each panel is fully zipped Figs 7 A 7 B Fig 7 A Fig 7 B 1 Unfold the canopy on the bed ACAUTION ALWAYS orient the canopy so the Instruction Storage Pocket is at the foot of the bed Fig 7 C 2 Release corner covers 3 Unzip all four vertical rail zippers 4 Beginning vvith one corner leg vvrap the canopy around the foam making sure that the foam is positioned toward the top
3. posts for both the head and foot of the bed frame Each post is labeled with a letter for easy assembly Reference the Posey Bed frame Fig 4 D location to assist with assembly Fig 4 A 3 Place the clamp onto the bolts Figs 4 E amp 4 F Frame assembly requires two people to provide stability and to help prevent injury Fig 4 E Fig 4 F 4 Place a flat washer and locking nut onto the bolt Fig 4 G Fig 4 A NOTE Use the control pad to elevate the head and knee portion of the frame for easier assembly Right Head Post i 1 Align the right head post Part I with the holes Fig 4 G on the frame located at the right side head of the bed Fig 4 C 5 Tighten with the 7 16 wrench Fig 4 H ACAUTION DO NOT over tighten Fig 4 B Fig 4 C NOTE Make sure the holes on the posts face inward and towards the center Fig 4 B Fig 4 H 10 Posey Bed 8070 Left Head Post 1 Align the left head post Part H with the holes on the frame located on the left side head of the bed Fig 4 J Fig 4 1 Fig 4 NOTE Make sure the holes on the posts face inward and towards the center Fig 4 1 NOTE Steps 2 5 shown for the Right Head Post will be repeated with each of the 4 posts Assemble each post completely before moving on to the next Right Foot Post 1 Align the right foot post Part N with the holes on the frame located on the right side foot of the bed Fig 4 L
4. rail Repeat with the second short rail between the left and right foot posts Parts M amp N 12 Posey Long Rail Assembly Materials e Hardware Packet A e Part G 2 e 9 16 wrench ACAUTION This section requires two people 1 Hold and align one of the long rails Part G between the left head and left foot posts Parts H amp M Fig 5 C Fig 5 C 2 Place a locking washer on four 4 1 bolts Hardware Packet A and insert one into each hole of the corner connection Fig 5 D Fig 5 D 3 Hand tighten the bolts loosely until all rails are installed Fig 5 E Fig 5 E Posey Bed 8070 Posey 4 Repeat on the other side of the rail 5 Repeat with the second long rail between the right head and right foot posts Parts amp N 6 Tighten all bolts short and long rails with a 916 wrench until there is resistance 5 F Fig 5 F 7 Gently hand shake each vertical post and top rails to ensure the bolts are securely fastened NOTE Use bed control pad to lower head and knee to the flat position Fig 5 G Posey Bed 8070 Bed Assembly 8 The frame assembly is complete Fig 5 H 13 Bed Assembly Foam Pad Assembly Materials e Parts E 2 F 8 1 Open the slot on a short foam pad Part E and wrap around the short rail at either the head or foot or the bed Fig 6 A NOTE Make sure that the slot faces outward from the bed frame
5. Posey Bed Where Comfort Meets Safety 8070 Assembly Instructions Only for Joerns Bed model number 2003DC B684DC modified for the Posey Bed U S Pat No 7 735 167 Rx ONLY Posey Company e 5635 Peck Road Arcadia CA 91006 0020 USA Phone 1 800 447 6739 or 1 626 443 3143 e Fax 1 800 767 3933 or 1 626 443 5014 e www posey com Table of Contents Introduction SA acct cec stern iat eee eeneeee 3 Safety Precauti ON Sa xumncccnaccconccccnn create nete nierit 3 Technical Specifications uses 4 General Information ccccsssessssscssesssssessssesssssessssecesseeesen 5 IGT AVIAN OM ka e E 5 Bed Assembly Unpacking the Parts und nr 6 Caster Leg ASSEM DY mana ncccnccccnc conte c renie cerenerece eee 7 8 Transfer Brake Assembly au umaccnnccconccccnnccccnnc zonen cenon eee 9 Frame Assembly e vnevion vidnimn 10 13 Foam Pad SON DI e acne 14 Canopy TMS Cali SOON ter nie 15 Canopy Head End Flap Installation ves 16 Mattress Installation ssssessssssssssssssssssssesssesssees 17 Power Cord AttacHMent ccscsssecsssecsseesseecsseesssecssees 18 Assembly CCC u arka seteniennae 19 Replacement Parts e treme A Mirren re re erent nr em O 20 Warranty Warranty Statement nn 21 Technical Service Technical Service Contact au ana aa manan sna ncnsnzo zene ne renien 22 Posey Safety Instructions The Posey Bed Assembly Instructions include important instructions and information related to the assembly of the be
6. Replacement Part Availability Part No A B C D OTOZ Kr KR IQmnm Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Description Hardyvare Spare Kit Foam Padding Short Foam Padding Long Frame Long Side Rail Frame Left Head Post Frame Right Head Post Caster Leg Frame Head Caster Leg Frame Foot Frame Short Side Rail Frame Left Foot Post Frame Right Foot Post Foot Transfer Brake Bed EasyCare 2003DC Mattress BioCore AHP Canopy Complete Panel Canopy Right Side Panel Canopy Left Side Quick Release Buckle w Strap Bed Control with Cable Caster Locking w Hardware Motor Assy Head Motor Assy Feet Motor Assy Up Down Bumper w Hardware Back Up Battery Control Box w Power Cord Caster Frame Padding Qty 1 kit eee M M Posey Cat No RP8070HDK RP80 70FMS RP8070FML RP8070FMHL RP80 70FHLT RP80 70FHRT RP80 70FCLH RP80 70FCLF RP8070FMHS RP80 0FFLT RP80 70FFRT RP8070TBF RP8070B RP8070M 80 70T RP80 70PRT RP80 70PLT RP8070QRB RP8070RMT RP8070LC RP807O0MOH RP8070MOF RP807 0MOUD RP8070BM RP80 0BAT RP80 70CBC RP80 70CFP Please call Technical Services for more information at 1 800 44 POSEY 1 800 447 6739 For cleaning instructions and warranty please refer to the Posey Bed 8070 user manual M6192 which may be downloaded at www posey com 8 Posey Limited War
7. d It is important to read the Assembly Instructions carefully prior to assembly of the bed for the first time In order to ensure safe assembly the operator must always comply with the instructions and warnings contained in the Assembly Instructions NOTE The protective devices installed on both the Posey Bed and the accessories may neither be removed nor modified Introduction Safety Precautions Warnings Cautions and Notes are provided throughout this manual to indicate levels of potential hazards or helpful information as defined below AWARNING Indicates a safety hazard or unsafe practice which if not avoided could result in serious injury or death Indicates a potential hazard in which failure to follow instructions may result in minor or moderate injury to the patient caregiver or damage to the Posey Bed NOTE Indicates a reminder or other helpful information to make bed assembly easier and more efficient Help Please call Posey Customer Support at 1 800 447 6739 between 6 00 am PST and 5 00 pm PST if additional help is required You can also contact an authorized Posey Bed dealer Introduction Specifications for Joerns Bed model number 2003DC FB684DC modified for the Posey Bed Power Supply Requirements Operating Conditions Model Posey Bed 8070 The Posey Bed is designed for use in normal indoor environments Rated voltage and current 108 132 VAC Storage Conditions The Posey Bed may be st
8. e Posey will pay return shipping costs for repaired or replaced products via Ground Service unless otherwise agreed How to Get Service Contact the Posey Technical Service hotline 1 800 447 6739 to report the problem and get a Return Authorization Number RMA Carefully pack and ship the return product to us with your RMA to Posey Company 5635 Peck Road Arcadia CA 91006 0020 e In clean condition Canopies that are returned soiled or with an odor will be returned immediately and will not be inspected or repaired e With proof of purchase and e Freight pre paid by you Posey will inspect the product and contact you within ten 10 business days from receipt of item to explain the results of our inspection and what is or is not covered How does State Law Apply This warranty is governed by the laws of the State of California USA It gives you specific legal rights You may have other rights which vary from state to state This warranty does not affect any further rights that you have under the laws in your state for sale of consumer goods Technical Service Posey Technical Service Posey Technical Service We are happy to assist you between the hours of 6 AM and 5 PM Pacific Time USA Please call us at 1 800 44 POSEY 1 800 447 6739 or 1 626 443 3143 You can fax us at 1 800 767 3933 or 1 626 443 5014 Shipping Ship items to Posey Company 5635 Peck Road Arcadia CA 91006 0020 USA Canopy Repairs To p
9. fer Brake Assembly Materials e Hardware Packet D e Part O 4 e 1716 wrench 2 1 Align the top and bottom holes on the Transfer Brake Part O with the two holes on the bed frame NOTE Make sure the holes in the brake are facing the holes in the bed frame Fig 3 A 2 Insert two bolts Hardware Packet D one into the top hole and one into the bottom hole of the transfer brake Fig 3 B Fig 3 B Posey Bed 8070 Bed Assembly 4 Use a 7716 wrench to tighten both bolts Fig 3 D NOTE Two 7716 wrenches are needed One to hold the bolt and the other to hold the nut ACAUTION DO NOT over tighten as a a T h J Sa Fig 3 D 5 Repeat steps 1 4 until all four transfer brakes are properly installed 6 Turn the bed assembly upright and lock all four casters by pressing down on the lock on each caster Fig 3 E ACAUTION Turning the bed upright requires two people Fig 3 E NOTE The bed platform cannot be raised lowered or articulated unless the power cord is plugged into an appropriate grounded AC electrical outlet Locate the control pad in the packaging under the bed frame to raise and articulate the frame Frame Assembly 2 Insert al Carriage bolt Hardware Packet B into each hole Figs 4 D Materials e Hardware Packet B e Part H I M N e Clamps 4 e 7 16 wrench NOTE The frame assembly consists of distinct left and right
10. l outlet to assist with assembly 1 Lay the bed frame Part P on the floor upside down Fig 2 A NOTE Bed motor will be located on the foot end Fig 2 A Bed Motor Fig 2 A 2 Insert the caster leg frame Part J Head Label into the wheel receiver at the head of the bed frame Fig 2 B NOTE The caster leg frame Part J must be placed in the wheel receivers opposite the bed motor Posey Bed 8070 3 Press firmly to seat the caster leg frame Part J completely down into the wheel receiver Fig 2 C 4 Insert the caster leg frame Part K Foot Label into the wheel receiver at the foot of the bed NOTE The caster leg frame Part K must be placed in the wheel receivers located near the bed motor Fig 2 D 5 Press firmly to seat the caster leg frame Part K completely down into the wheel receiver 6 Secure the Caster Leg Frames onto the bed frame starting with either the head or foot using the square plugs Hardware Packet C Fig 2 E 7 Place a lock washer on a 1 bolt Hardware 9 Tighten with a 9 16 wrench Fig 2 G Packet C and insert it into a square plug with ACAUTION DO NOT over tighten channel fitting Fig 2 E Fig 2 E 10 Repeat until all four square plugs have been installed 8 Put the plug and bolt into the hole on top of the caster leg frame using the square plug and receiver Fig 2 F Fig 2 F 8 Posey Bed 8070 PPosey Trans
11. mended that a second person assist with the assembly of the Posey Bed 8070 to provide stability and to help prevent injury The Bed Assembly portion requires two people Introduction Installation Gather assembly tools not included in the boxes 2 7 16 combination wrenches or sockets 2 9716 combination wrenches or sockets Bed Assembly Unpacking the Parts Confirm that all parts have been included vvith the bed If any items are missing or damaged please contact Posey Technical Service at 1 800 447 6739 Description Hardware packet 1 bolt amp lock washers 12 ea Hardware packet 1 14 carriage bolts flat washers amp nuts 8 ea Hardware packet square plugs lock washers amp bolts 4 ea Hardware packet 2 bolts amp nuts 8 ea Posey Ss Description NJ Short foam canopy pads ong foam canopy pads ong side rails eft head post vvith clamp 1 Right head post with clamp ae ead caster leg frame nm oot caster leg frame 2 Short side rails Left foot post with clamp Right foot post with clamp 4 Transfer Brakes Bed frame Joerns Bed 2003DC Model B684DC 1 Triple ply therapeutic foam mattress 1 ot x lt Posey Bed Canopy Posey Bed 8070 Caster Leg Frame Assembly Materials e Hardware Packet C e Parts amp K e 9716 wrench NOTE Bed assembly should be done near an appropriate AC electrica
12. nt taped to the underside of the bed 1 Attach the bed control to the canopy 2 Place the bed control into one of the pockets near the foot of the bed Fig 10 A Y Fig 10 A 3 Secure the bed control with the bed control clip Fig 10 B 18 Posey Bed 8070 Posey Assembly Check 1 The bed assembly is completed Fig 11 A Fig 11 A Check V Bed frame feels secure with no loose or moving parts v All casters lock when caster lock is engaged V Lower bed to the lowest position to ensure transfer brakes engage securely VY No foam is visible v All zipper pins are completely seated in the pin box and all zipper teeth are engaged v No rips or holes in the canopy or netting VY Zippers open easily and close securely with no holes or gaps along the entire length of the Zipper v All corners are covered and secured with the hook and loop covers Y No hardware is left over Posey Bed 8070 Bed Assembly 2 Store all Posey Bed instructional material in the instruction storage pocket at the foot of the bed Fig 11 B Fig 11 B 3 The Posey Bed is now ready for delivery or storage NOTE The Posey Bed is designed for use in normal indoor environments The Posey Bed may be stored in ambient warehouse temperatures at normal humidity levels Avoid excess moisture or high humidity that may damage product materials 19 Replacement Parts 8070 Replacement Parts
13. of the frame Fig 7 D Posey Bed 8070 Bed Assembly 5 Pull the canopy material together and zip only half way up Fig 7 D NOTE Zipping half way assists with the installation of the top portion of the canopy 6 Repeat on the other three sides until the corner legs are covered NOTE Ensure the zipper pins are seated properly Fig 7 B 7 Unzip all horizontal rail zippers both the long and short sides 8 Beginning with one long side wrap the top rail section around the foam pull the canopy material together and zip Fig 7 E Fig 7 E NOTE Ensure the zipper pins are seated properly Fig 7 B 9 Repeat on the other three sides until the long and short side rails are covered 10 Secure each corner cover with the hook and loop 11 Conduct a visual check to make sure that no foam is visible and that all zipper teeth are engaged 15 Bed Assembly Posey Canopy Head End Flap Installation 1 Locate the Canopy Head End Flap at the head of the bed Fig 8 A 2 Open the hook and loop and wrap around the metal end of the head of the bed Fig 8 B Fig 8 A 3 Secure the hook and loop Fig 8 B 16 Posey Bed 8070 Posey Mattress Installation Materials e Part Q 1 e Assembled Bed Frame with Canopy PAUA ISIS CET If not using the Posey Bed 8070 mattress a mattress that measures 6 x 35 x 80 15 x 89 x 203 cm must ONLY be used Any o
14. ored in ambient Frequency 60Hz warehouse temperatures at normal humidity levels Avoid excess moisture or high humidity Current Rating 1 6 Amps 110 120V unit that may damage product materials Classification Class Il Type B Double insulated Circuit Protection 250V F1 36A 110 120V unit Mode of Operation 10 Maximum duty cycle Dimensions Highest Position Inches 84 25 W x 40 75 D x 73 25 H Centimeters 214 W x 104 D x 186 H Lowest Position Inches 84 25 W x 40 75 D x 62 75 H Centimeters 214 W x 104 D x 159 H Area 19 5 Square Feet Sleep Surface Volume Inside 70 Cubic Feet 2 cubic meters Maximum Back Angle 65 to Horizontal Maximum Knee Angle 35 to Horizontal Maximum Knee to Leg Angle 45 to Horizontal Unit Weight Canopy Only 17 lbs 8 Kg Assembled Bed 278 lbs 126 Kg including mattress Posey General Information This section provides detailed installation and setup instructions for the Posey Bed on the Joerns Bed model number 2003DC B684DC modified for the Posey Bed The installation steps must be followed correctly to ensure proper operation and service Read these Assembly Instructions carefully before attempting to assemble the bed Follow all instructions carefully Select a place where sufficient clearance can be provided around the bed Ample working space is necessary around and above the bed The bed is heavy and large therefore it is strongly recom
15. ranty Posey Limited Warranty What Does this Warranty Cover Posey warrants to the original purchaser that the Posey Bed 8070 is free of defects in materials and workmanship If the product is found to be defective in workmanship or materials we will repair or replace it at our option at no charge other than certain transportation and cleaning charges How Long Does the Warranty Last This warranty is two 2 years from the date of purchase for the bed frame five 5 years from the date of purchase for the mattress and one 1 year from the date of purchase for the canopy Useful life of the Posey Bed canopy is estimated at three 3 years What is NOT Covered by this Warranty e Damage to the metal frame nylon canopy or other components caused by 1 use in unsuitable environmental conditions or failure to assemble or maintain the product in accord with user and service instructions 2 abuse including but not limited to patient damage misuse alteration exposure to extreme heat or by natural or external forces such as flood or fire e Damage caused by alteration modification or repair unless performed by Posey e Consequential or incidental damage including but not limited to loss of income or profits is not covered The laws of some countries may not allow exclusion of such damages so this limitation may not apply to you Cleaning and Shipping Charges e Shipping costs for products sent to Posey must be pre paid by you
16. revent damage in shipping clean the canopy and close all zippers In Warranty Repairs 1 Forward the product in clean condition prepaid freight to the above address 2 Clearly mark the shipping container with the RMA number 3 Include dated proof of purchase Out of Warranty repairs 1 Forward the product in clean condition prepaid freight to the above address 2 We will quote repairs on an item by item basis All quotes include parts and labor 3 If additional repairs are needed after the initial estimate we will contact you within ten 10 business days from receipt of item to obtain approval of any extra charge Repair turn around Normally we will ship the product back to you within three weeks from the date of receipt at our warehouse If you return multiple units add one week per unit We will return all units in one shipment unless otherwise agreed Canopies that are returned soiled or with an odor will be returned immediately and will not be inspected or repaired gt w aon o a i Pose Where Comfort y Bed Meets Safety Posey Company e 5635 Peck Road Arcadia CA 91006 0020 USA Phone 1 800 447 6739 or 1 626 443 3143 e Fax 1 800 767 3933 or 1 626 443 5014 e Web www posey com 2013 Posey Company All rights reserved M6193 REV C 053113
17. ther size mattress may result in patient injury or death 1 Completely unzip the mattress compartment ACAUTION Orient the mattress with the label on the foot of the bed 1 before placing it into the mattress compartment Fig 9 A Fig 9 A 2 Insert the mattress Part Q into the mattress compartment Fig 9 B ae 8 i a oe s rs i i z5 A I Q SS i Bin z Te e f Ses mi Fig 9 B 3 Completely zip the mattress compartment Fig 9 C Posey Bed 8070 Bed Assembly 4 Attach the canopy to the bed frame by securing both bed straps located in the middle of the long sides of the bed ACAUTION The canopy bed straps must ALWAYS be connected to movable parts of the bed frame to avoid damaging the mattress compartment 5 Insert the strap through the bed frame Figs 9 D amp 9 E Insert Strap pS p Through Here www posey com L9350A 112707 Fig 9 D Fig 9 E 6 Bring the strap up through both D rings and then back in between the first and second D ring Figs 9 F amp 9 G Fig 9 F Fig 9 6 7 Pull strap straight down to tighten Fig 9 H Fig 9 H 8 Repeat on the other side of the bed frame 17 Bed Assembly Posey Power Cord Attachment 4 Secure power cord with the power cord strap located at the head of the bed Figs 10 C 10 D NOTE If not already done retrieve the power amp 10 E cord attachme
Download Pdf Manuals
Related Search