V8FR-II V8R7-II最新
Contents
1. RED LED of the transmitter module will be off GREEN LED will flash rapidly The effective distance will be decreased to 1 30 of full range 5 Walk away from the model while simultaneously operating the controls on the transmitter confirming that all controls operate normally to a distance of at least 30 meters 30 yds 6 Press the F S button of the transmitter module for 1S 4S to exit range check mode RED LED will be back on indicating normal operation is back 2 3 Failsafe setting Failsafe is a useful feature in which all controls move to a preset position whenever the control signal is lost for a period of time V8FR II V8R7 Il supports failsafe function for all channels Follow the steps below to set failsafe positions for each channel 1 Bind the receiver first and turn on both the transmitter and the receiver 2 Move the controls to the desired failsafe position for all channels 3 Press briefly the F S button on the receiver less than 1 second The GREEN LED of the receiver will flash twice indicating the failsafe position has been set in the receiver Note When set failsafe try to not be too close to the transmitter to avoid blocking the signal artificially Re bind the receiver will DISABLE all the failsafe s set BEFORE Failsafe is recommended to set when system is firstly used or receiver has been re bound Follow steps below to set failsafe Option 1 How to set failsafe to a user determined state on lost signa2. D on the transmitter module will flash indicating the transmitter is ready to bind to the receiver 3 Put V8FR II V8R7 II into binding mode see 1 1 Compatibility chart for details the LED on V8FR II V8R7 II will flash indicating the binding process is completed 4 Turn off both the transmitter and V8FR II V8R7 II and disconnect the jumper from V8FR II V8R7 II after binding with telemetry module in D_ Mode ES EU TRUliL Instruction Manual for FrSky bkk IRUNG V8FR II amp V8R7 II 5 Turn on the transmitter and connect the battery to V8FR II V8R7 II The GREEN LED on the receiver will indicate the receiver is receiving commands The transmitter module receiver binding will not have to be repeated unless one of the two is replaced 2 2 Range check A pre flight range check should be done before each flying session Reflections from nearby metal fences concrete building or trees can cause loss of signal both during range check and during the flight The following steps are to be followed to perform the range check of the model before the flight 1 Place the model at least 60cm two feet above non metal contaminated ground e g on a wooden bench 2 The receiver antennas should be separated in the model and do not touch the ground 3 Place the antenna of the transmitter in a vertical position 4 Turn on the transmitter and the receiver press the F S button of the transmitter module for 4 seconds to enter range check mode the
3. PrSKY ELEGTRONiG We Introduction 1 1 Description amp compatibility FrSky modules How to put V8FR II V8R7 II into binding mode respectively V8FT V8JT V8HT V8_Mode Non telemetry Connect battery to DFT DJT DHT DHT U in V8_Mode V8FR II V8R7 II while holding the F S button on V8FR II V8R7 II Switch 1 OFF and Switch 2 ON l D_Mode Telemetry Connect Ch1 amp Ch2 signal pins of DFT DJT DHT DHT U in D_Mode V8FR II V8R7 II by provided jumper and then connect battery to Switch 1 OFF and Switch 2 OFF V8FR II V8R7 ll directly no need to hold the F S button on V8FR II V8R7 Il 1 2 Specifications V8FR II 4 24 14mm Specified Range Full Range gt 1 5km SsrAv7 I 2 4Gry b Aca gt Actearced Cornea Crane Sremeng o rensa agy m 1 3 New feature of V8FR II over V8FR HV Compatible with all FrSky modules V8_mode amp D_mode receive only V8FR II can talk with module of either mode but it does not send telemetry information back to the transmitter 1 4 New feature of V8R7 II over V8R7 Compatible with all FrSky modules V8_mode amp D_mode receive only V8R7 II can talk with module of either mode but it does not send telemetry information back to the transmitter 2 Setup 2 1 Bind procedure 1 Turn on your transmitter and switch it to PPM mode Turn the transmitter off 2 Turn on the transmitter while holding the F S button on the transmitter module Release the button The RED LE
4. l 1 Bind the receiver to the transmitter module first and turn on both the transmitter and the receiver 2 Move the controls to desired failsafe position for all channels 3 Press briefly the F S button on the receiver and you are done Option 2 How to set failsafe for no pulses on lost signal 1 Just press briefly the F S button on the receiver while the transmitter is off and you are done Note If failsafe is not set failsafe default will hold last position before signal is lost In this case there exists risk that your model will fly away or cause injury
Download Pdf Manuals
Related Search