Operating manual
Contents
1. REPAIR Return the instrument to your distributor for any work to be done whether under the warranty or not If you have to ship the instrument it is best to use its original packaging and to state as clearly as possible in anote attached to the equipment the reasons for the transfer WARRANTY The equipment is warranted against defects of materials or workmanship in accordance with the general terms of sale During the warranty period 1 year the instrument must be repaired only by the manufacturer who reserves the right to choose between repairing it or replacing it entirely or partially If the equipment is sent back to the manufacturer carriage is paid by the customer The warranty does not apply in the following cases E Inappropriate use of the equipment or use with incompatible equipment E Modifications made to the equipment without the explicit permission of the manufacturer s technical staff Work done on the device by a person not approved by the manufacturer E Adaptation to a particular application not anticipated in the definition of the equipment or not indicated in the user s manual E Damage caused by shocks falls or floods DMM 111 TO ORDER A T E TE AT P06231420Z 11 2013 694308A02 Ed 2 http www chauvin arnoux com2. and IEC 61010 2 033 for voltages up to 600V in category III Failure to observe the precautions for use and safety instructions may cause an electric shock fire explosion or destruction of the instrument and of the installations Em The operator and or the responsible authority must carefully read and clearly understand the various precautions to be taken in use If you use this instrument other than as specified the protection it provides may be compromised thereby endangering you m Do not use the instrument on networks of which the voltage or category exceeds those mentioned m Observe the environmental conditions of use m Do not exceed the rated maximum voltages and currents between terminals or with respect to earth E Do not use the instrument if it seems to be damaged incomplete or poorly closed E Before each use check the condition of the insulation on the leads housing and accessories Any item of which the insulation is deteriorated even partially must be set aside for repair or scrapping m Use only the leads and accessories supplied Using leads or accessories of a lower voltage or category reduces the voltage or category of the combined instrument leads or accessories to that of the leads or accessories m Use personal protective equipment when conditions require E When handling the leads test probes and crocodile clips keep your fingers behind the physical guard E Keep your hands away from
3. 10 00 A Fuse 10 A 600 V 20 A for 30 s Fuse 0 63 A 600 V AC current measurement Intrinsic uncertainty 1 5 5 ct 200 0 pA 2000 pA Fuse 0 63 A 00 mA 600 V 200 0mA 40 Hz 500 Hz 2 000 Fuse 10 A 10 00 A 600 V 20 A for 30 s Diode test Intrinsic uncertainty dhe Resistance measurement Intrinsic uncertainty No load voltage approx 0 4V 200 0 Q 0 5 3 ct 2 000 kQ Continuity measurement Range ntririsic Observations uncertainty No load voltage approx 0 4V R lt 909 409Q 0 5 2 ct 200 00 0 5 3ct ENVIRONMENTAL CONDITIONS Indoor use Altitude lt 2 000 m Degree of pollution 2 o l 10 C 50 C 20 C 60 C lt 70 RH without condensation lt 80 RH without condensation Relative humidity CONSTRUCTIVE CHARACTERISTICS Dimensions L x W x H 181 x 92 x 57 mm Weight approx 400 g POWER SUPPLY Battery 2x1 5V AA LR6 Mean battery life 600 hours Auto power off delay After 15 minutes without action on the keys and or on the switch COMPLIANCE WITH INTERNATIONAL STANDARDS Compliant with standards IEC 61010 1 and IEC 61010 2 033 for 600V CAT III installations Maximum input voltage 600V between terminals ELECTROMAGNETIC COMPATIBILITY Emissions and immunity in an industrial environment per EN 61326 1 MAINTENANCE Except for the fuse and the batteries the instrument contains no parts that can be r
4. Multimetrix DMM111 Multimeter amp a Multimetrix DMM 111 g SELECT RANGE MAX HOLD MULTIMETER 00 0 es ST You have just purchased a DMM111 digital multimeter and we thank you for your confidence For best results from your instrument E read these operating instructions carefully E comply with the precautions for use WARNING risk of DANGER The operator must refer to this user s manual whenever this danger symbol appears Equipment protected by double insulation Earth Instruction that must be read and understood AC Alternating current DC Direct current Battery The CE marking indicates conformity with European directives The rubbish bin with a line through it means that in the European Union the product must undergo selective disposal for the recycling of electric and electronic material in compliance with Directive WEEE 2002 96 EC This equipment must not be treated as household waste Definition of measurement categories E Measurement category IV corresponds to measurements taken at the source of low voltage installations E Measurement category Ill corresponds to measurements on building installations E Measurement category II corresponds to measurements taken on circuits directly connected to low voltage installations PRECAUTIONS FOR USE This instrument and accessories are compliant with safety standards IEC 61010 1 IEC 61010 031
5. eplaced by personnel who have not been specially trained and accredited Any unauthorized repair or replacement of a part by an equivalent may gravely impair safety CLEANING Disconnect the unit completely and turn the rotary switch to OFF Use a soft cloth dampened with soapy water Rinse with a damp cloth and dry rapidly with a dry cloth or forced air Do not use alcohol solvents or hydrocarbons REPLACEMENT OF THE BATTERIES The 4 symbol indicates that the batteries are dead and must be replaced To replace the batteries proceed as follows E Disconnect the unit completely and turn the rotary switch to OFF E Remove the jacket m Unscrew and remove the 4 battery compartment cover screws E Remove the old batteries and insert the new ones with the polarities as indicated Spent batteries must not be treated as ordinary household waste Take them to the appropriate mae cycling collection point REPLACING THE FUSE When the measurement current exceeds the current rating of the fuse the protection fuse may blow F1 FF 104 1000V 1 FF 630mA 1000V Fe For safety reasons this fuse must always be replaced by an identical model F1 10x38 type FF 10A 600V F2 6 3x32 type FF 630mA 600V When the current measured exceeds the rating of the fuse the fuse may blow
6. s MEASUREMENTS A mA Mo VOIP T A pAmA COM Vo A mA COM Vo e SER O i yeay A X 4 N y 4 Nior A A The input voltage must not exceed 600V pAn AC voltage measurement Vv pA BCC a eek een se pa A ve Ly OFF V DC voltage measurement ELECT RANGE MAX HOLD apn AC current measurement A A pAmA COM Va 4 BS s 00O veas A ELECT RANGE MAX HOLD A pAmA COM Vara O SELECT A pAmA COM Va 4 Z5 g amp Resistance measurement Q Resistance and capacitance measurements and diode and continuity tests must be performed on voltage free circuits A pAmA 6 COM va 4 A pAmA COM vo s mgA Diode test gt gt t Va CHARACTERISTICS ELECTRICAL CHARACTERISTIC Reference conditions Quantity of influence Relative humidity 45 to 75 RH Frequency measurement Square wave without DC The intrinsic uncertainties are stated in x of reading Y points from 10 to 100 of the range DC voltage measurement Range Intrinsic Input resistance 9 uncertainty P L e Se 0 5 3 ct 10 MQ 6v AC voltage measurement Frequency Intrinsic Input Range range rs cs 200 0 mv 1 10ct ct 11 MQ MQ a 000 V 40 Hz ae J 00 V 500 Hz 1 5 ct 10MQ TE OV eov V DC current measurement Intrinsic uncertainty 1 5 3 ct 200 0 pA 2000 pA 20 00 mA 200 0 mA 2 000
7. the terminals of the instrument E Replace the battery as soon as the amp symbol appears on the display unit Disconnect all leads before opening the battery compartment cover PRESENTATION The DMM111 is a device for measuring electrical quantities E AC or DC voltage measurement DC and AC current measurement E Resistance measurement continuity measurement with buzzer or diode test LCD display unit Keys Battery compartment oby cover vat Sore all Switch z Prop wale al an Input OFF terminals Battery compartment Impact resistant jacket cover screws USE INSERTING THE BATTERIES See Maintenance TEST OF OPERATION e n SWITCHING OFF THE MULTIMETER Manual switching off Set the switch to OFF Automatic power down The automatic power down function of the device is reactivated when the device is switched back on SELECT CHANGING MODES Several modes may be available for a given function existence of additional modes indicated by a yellow symbol Press the SELECT key to change which mode is active m CO W SELECT RANGE CHANGING RANGES AUTO RANGE MAX Continuity test e1 MAX FUNCTION rE E TE a en O F wal Shoe l J H v aN SELECT C BOSSI X HOLD e997 42 1 R lt 90Q9 n DC current measurement A HOLD HOLD OF THE DISPLAY a
Download Pdf Manuals
Related Search