MBUS-Demo_User_Manual
Contents
1. 12 2008 AS MBUS DEMO User Manual rev 1 30 Page 1 of 12 ettet Wireless solons MBUS DEMO Installation Guide The MBUS DEMO is a part of Radiocrafts RCTools PC suite tailored for use with Radiocrafts RF Modules For full installation procedure please read the RCTools Installation Guide available at www radiocrafts com The MBUS DEMO requires access to the modules UART via an available COM port Typically the UART access is obtained via an UART to RS232 or UART to USB converter The Demo Boards DB from Radiocrafts contain an on board level shifter for direct plug in to a PC and further access to the related COM port Screen Settings is recommended to run the application with screen size at least 1024x768 and resolution 96dpi 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 2 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO Introduction MBUS DEMO is designed to demonstrate a Wireless M Bus system using the Radiocrafts Wireless MBUS module development kit The program provides Module Quick setup MBUS Packet generator MBUS Packet Sniffer and an Installation tool for the MBUS2 MBUS3 feature set A Radiocrafts MBUS Demo Board is needed for this demo to operate properly MBUS DEMO 1 33 T 19200 z COM1 DISCONNECTED i STATUs Network role MBUS Mode2. Slave Master Os OR Radiocrafts Repeater Embedded Wireless Solutions Install Mode Install Accept All Other settings Auto sleep Enable RSSI of After TX Clear installed meters After TX or RX C Enable LED Control Mailbox O acsm acme 1 mesm orc MBUS ID and Address field Module Details C4ield M4ield Afield MBUS Feature set Hardware revision Fimware revision Figure 1 Main window Start the program and the MBUS DEMO main window should look similar to what is shown in Figure 1 Connecting to the Module Before connecting select the proper settings for your serial port name of an available communication port COMx baud rate used to communicate with the module T 19200 g COM1 z lema L Figure 2 Port settings To connect to the module you need to press the connect button If your COM port is not listed you can also manually type in the COM port to use 1 Mil Figure 3 Connect button A warning message will pop up if you try to connect to a port that is already in use This is illustrated in figure 4 tj Could not connect Access to the port denied Figure 4 COM port conflict message 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 3 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO Module Quick Setup Tab The Module Quick setup Tab allows you to read back a
3. E Send a packet from the Packet Generator Tab after the Auto Select to send a new packet typ 100 ms after first ACK Select to enable Auto ACK Enable Read pre installed Will be auto cleared if encryption meters from module emulator started and a new packet received from meter The selected packet form the Packet Generator tab is used Figure 8 MBUS2 Concentrator Install Emulator Step by step guide for installing a meter to the MBUS2 Concentrator Emulator Ensure that you have the MBUS2 feature set on the connected module Configure the Demo Board as Master enable accept Install messages and include RSSI in the Module Quick Setup tab Read pre installed meters by pressing left arrow key Start the search for new install messages pressing the toolbar start button Wait for the install message from a meter you want to install Select the meters you want to install Click on the right arrow button to install the selected meter N If Auto ACK is enabled the Master will automatically send ACK when receiving a new message from the installed slave The Auto ACK flag will be cleared after the Master send this ACK You may also enable to send a packet from the packet Generator tab after this first ACK according to NTA8130 You can change mode to normal mode and use the packet sniffer to receive messages from installed meters only after the installation is completed The Install Emulator will only
4. ettet Wireless mms lt lt lt MBUS DEMO MBUS DEMO User Manual gt 20 Q Demo 10 100 E c gt Q act 180 MBS Demo 1 90 Jog Table of Contents TABLE OF CONTENTS aerate c M 1 INSTALLATION cju c E 2 cp 2 ec 3 CONNECTING TO THE MODULBE cu dra o dE 3 MODULE QUICK SETUP TAB uoi tts barn Evo case sans icu dudo 4 MBUS PACKET GENERATOR 5 MBUS PACKET SNIFFER cx xa Rue 6 CONCENTRATOR INSTALL EMULATOR 7 ENCRYPTION KEY 10 DOCUMENT REVISION 5 12 bie Boo area 12 TRADEMARK 12 LIFE 0 ea e i 12 CONTACT INFORMATION
5. TUS Master T1 Idle ID 0CAE 12345678 0 L07 Total packet to Module Quick setup Packet Generator MBUS PacketSniffer Concentrator Install Emulator Encryptierr Key Generator df h MBUS Packet selection 2 RC1180 MBUS Meter Illustration sen or the ms sek min Railioerafts periodic TX Packet rate ms 1000 hn Embedded Wireless Solutions m nm Select a packet type to send to the module Total packets 100 Tar JA gt S L Packet SMD NR Meter gt MUC counter Enable Wakeup before TX 5 Number of packet MBUS C4ield and UART packet sent UART Packet format to the C Lenght Cl Data Field 44 29 2A0000002F2F0C 1427048502046D32371F1502FD 1700002F2F2F2F2F2F2F2FE1B32F2F2F2F2F25EE module send to UART send to mailbox add to message list E enter packet name her Type the name of the added packet A in the list Send the selected Select packet to the module Add the selected Mailbox MBUS3 only C field stored in Send the selected Module volatile Memory packet to the module once packet to the packet list selection Figure 6 MBUS Packet Generator Step by step guide for setting up the MBUS Packet Generator in periodic TX mode Configure the Demo Board as Slave in the Module Quick Setup tab Select the MBUS Packet Generator tab Set the Packet rate that gives th
6. 2010 2 31 28 PM 51 46 OCAE CEN 12345678 01 07 7A 010008802F2FODFD0C0434474B42 61 3 4 2010 2 31 34 PM 51 46 OCAE CEN 12345678 01 07 7A 010008802F2F0DFD0C0434474B42 61 3 4 2010 2 31 39 PM 51 46 OCAE CEN 12345678 01 07 010008802F2F0DFD0C0434474B42 61 3 4 2010 2 31 43 PM 51 46 OCAE CEN 12345678 01 07 _ 010008802F2FODFD0C0434474B42 61 3 4 2010 2 31 43 PM 1A 44 16F4 EWT 01140781 55 62 A2 51170 160151170 16037 9 1 107 52 5 3 4 2010 2 31 53 Timestamp Auto clear list after 10 packets Auto clear log to MBUS Mouse over tool tip if Select all packets in Timestamp the log To be used for when received recude the log list Packets Data field larger than The packet counter received log window size will not be cleared Copy paste into Excel sheet Figure 7 MBUS Packet Sniffer Step by step guide for setting up the MBUS Packet Sniffer 1 Configure the Demo Board Master enable accept all messages and include RSSI in the Module Quick Setup tab 2 Select the MBUS Packet Sniffer Tab 3 Start the MBUS Packet Sniffer from the toolbar start button The MBUS Packet Sniffer will now count the total number of received MBUS packets and list them in the Meter Collector data field including RSSI and packet ID for each new packet The meter collector will continue to search for MBUS packets until the Sniffer is stopped
7. list up 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 7 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO new meters even if they send several packets This will simplify the meter selection and easily inform about available meters to install The user window for the Concentrator Install Emulator for MBUSS is illustrated in figure 9 Start Stop seach Reset Install list Will not clear the seach for for new installed meters in the module To clear Install selected meters new meter installed meter go to quick setup tab from the list meters Bi 1 33 ees e CONNECTED d Start C Reset STATUS Master T1 Idle ID 0CAE 12345678 01 07 Module Quick setup MBUS Packet Generator MBUS Packet sniffer Concentrator Install Emulator Encryption Key Generator MBUS3 Consentrator Installed meters Flag Register Mailboxes C4ield M4ield Afield UID VER DEV Meter install Meter status Meter manufacturer 44 16F4 01140781 55 1 New Meter detected EWT Elin Wasserwerkstechnik 07 2 New Meter detected Wireless MBUS mo Radiocrafts Embedded Wireless Solutions Avilable meters to Select Meter details Read pre installed install to install meters from module meter Figure 9 MBUS3 Concentrator Install Emulator Step by step guide for installing a meter to the MBUS3 Concentrator Emulator Ensure that you have the MBUS2 feature set
8. on the connected module Configure the Demo Board as Master enable accept Install messages and include RSSI in the Module Quick Setup tab Read pre installed meters by pressing left arrow key Start the search for new install messages pressing the toolbar start button Wait for the install message from a meter you want to install Select the meters you want to install Click on the right arrow button to install the selected meter Ne oS oS Auto ACK and encryption setting for MBUSS is available in the Register flag tab This is illustrated in figure 10 and is only available for MBUS3 02008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 8 of 12 Select the installed slave to configure MBUS DEMO Update module flag register for selected slave CONNECTED MwStart Stop Reset STATUS Master T1 Idle ID 0CAE 12345678 01 07 E EEE ee Module Quick setug MBUS Packet Generator MBUS Packet sniffer Concentrator Install Emulator Encryption Key Generator MBUS3 Consentrator slave number 1 go Standard master reply messages E CNF R 1000 0000 ACK 0100 0000 REQ UD1 0010 0000 E REG UD2 0001 0000 Installed meters Register Mailboxes other flags E Reserved 0000 1000 Encryption Mailbox number E REG UD1 0000 0100 Decryption o C REG UD2 0000 0010 C Frame Count Bit SND NKE 0000 0001 C Reserved Radiocrafts Embed
9. using the stop button on the toolbar All collector data can be selected in order to copy paste the information to an Excel spreadsheet for further analysis The reset button will empty the logger and set the packet receive counter to zero 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 6 of 12 Embedded Wireless Solutions MBUS DEMO Concentrator Install Emulator Tab The Concentrator Install Emulator tab is a tool for installing and binding meters to the RC1180 MBUS module The module will act as a Wireless M Bus concentrator that only accepts installed meters This tab is not in use for MBUS1 and different for MBUS2 and MBUSS3 The user window for the Concentrator Install Emulator for MBUS2 is illustrated in figure 8 Start seach Stop seach Reset Install list Will not clear the for new for new installed meters in the module To clear Install selected meters meters meter installed meter go to quick setup tab from the list Avilable meters to install Meter details Select RJ MBUS DEMO 1 33 MBUS2 to install CONNECTED 1 Stop Reset STATUS Master T1 Idle ID 0CAE 12345678 01 07 meter Module Quick setup MBUS Packet Generator MBUS Packet sniffer Concentrator Install Emulator Encryption Key Generator BUS2 consentrator Encryption Meter statis Meter manufacturer E 0 07 New meter detected Acce CEN Radiocrafts Wireless ay
10. BUS3 Mailbox readout 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 9 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO Encryption Key Generator The Encryption Key Generator tab is a tool for MBUS2 and MBUSS to calculate and update the connected module with encryption keys The view is different for MBUS2 and MBUS3 and figure 12 shows MBUSS3 Encryption key generator Tab If Master select installed Update Master slave slave register If Slave use with key Select this to get a default test key for master and slave Bi MBUS DENO 1 __ ee installation register 1 ONNECTED er T1 Idle ID 0CAE 12345678 01 07 Module Quick setup MBUS Packet Generator 4 MBUS Packet sniffer Concentrator Install Emulator Encryption Key Generator Start fjJReset STATUS Masi Random Encrypten Key Generator Write Key to module Master Key Use Default Test Key set Installation register 00112233445566778899AABBCCDDEEFF 1 L3 Slave Key 001122334455667788SSAABBCCDDEEFF Radiocrafts Embedded Wireless Solution Calculates a random Master and Slave key on each button click Figure 12 MBUS3 Encryption Key Generator Step by step guide for enable Encryption for MBUS3 Master 1 Install a meter to a register 1 64 2 Calculate an encryption key and update Master with key to installed slave register 3 Enable encryption in the Concentrator Insta
11. ded Wireless Solutions Selection of Standard message reply from master Encryption setting for Master and Slave Select a Master reply Read module flag message from the register for selected mailbox slave Figure 10 MBUS3 Flag Register The mailbox feature for MBUS3 can be read from the Mailbox tab In figure 11 is illustrated a readout when mailbox 1 and 3 is in use To write to the mailbox use the packet generator tab as shown in figure 6 Rd MBUS DEMO 1 33 MBUS3 Wow ee CONNECTED if Start Stop fjJReset status Master T1 Idle ID 0CAE 12345678 01 07 Module Quick setup MBUS Packet Generator MBUS Packet sniffer Concentrator Install Emulator Encryption Key Generator MBUS3 Consentrator Installed meters Flag Register C4ield Lenght Mailboxes Cl4ield Data field 28 7A 00 00 2A0000002F2F0C 1427048502046D32371F1502FD 1700002F2F2F2F2F2F2F2FE1B32F2F2F2F2F2 this mailbox is empty 7A 0900D0C52F2F11BBCCDDEEFFAABBCCDDEEFFAA1122AABBCCDDEEFFAABBCCDDEEFFAABB this mailbox is used by another mailbox for extended packet lenght this mailbox is used by another mailbox for extended packet lenght this mailbox is used by another mailbox for extended packet lenght this mailbox is empty this mailbox is empty this mailbox is empty this mailbox is empty Radiocrafts Embedded Wireless Solutions Figure 11 M
12. dule Non Volatile memory and status details Figure 5 Module Quick Setup after MBUS3 read back Step by step guide for Module Quick Setup 1 Connect the Radiocrafts MBUS Demo Board to an available COM port 2 Read back configuration settings from the Demo Board 3 Change settings and update the connected Demo Board if needed For detailed configuration it is advised to use the more powerful MBUS CCT tool instead of the MBUS DEMO software You will then get access to all configuration parameter settings of your connected module 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 4 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO MBUS Packet Generator Tab The MBUS Packet Generator Tab allows you to set up one of the RC1180 MBUS modules as a meter that sends meter status on request or periodically The UART package from the PC to the RC1180 MBUS is listed and part of the message can be changes by the user This package is received from the meter via the UART interface directly to the RC1180 MBUS as illustrated in the picture The user entries for the MBUS Packet Generator window is illustrated in figure 6 Start periodic send Send a OxFF wake up byte before Set time resolution the packet Should be enabled when Stop periodic send for Packet rate MBUS2 MBUS3 is configured for setting Auto sleep in quick setup F Packet rate setting CONNECTED Start Reset ST
13. e periodical interval in ms optional Set the total packets to transmit in the periodic test optional Select a packet to transmit Change the packet payload if needed optional Start the periodic transmit from the toolbar start button Noo ey The packet counter will now increment and send the UART packet periodically according to the Packet rate until the total packets has been transmitted The user can stop and reset the periodic transmission from the toolbar 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 5 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO MBUS Packet Sniffer Tab The MBUS Packet Sniffer tab allows you to set up one of the RC1180 MBUS modules as a Wireless M Bus Collector This board will act as a Wireless M Bus packet sniffer that receives and lists all incoming Wireless M Bus packets for the selected MBUS mode The user window for the MBUS Packet Sniffer is illustrated in figure 7 Reset Packet Sniffer Number of Send apacket from the MBUS packets Received Packet generator Tab To be Stop Packet Sniffer used to verify Auto ACK feature Start Packet Sniffer re Basso 135 05 NON LM CONNECTED R adi ocrafts MBUS packets received OK 6 Embedded Wireless Solutions Send a packet from the Packet Generator tab C4ield M4ield Adield UID Data field 1A 44 16F4 EWT 01140781 55 62 A2 21170F16D31F56E34C9A69F6AD4 94 3 4
14. iocrafts radiocrafts com sales radiocrafts com Suopport radiocrafts com 2008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 12 of 12
15. ll Emulator Flag Register see figure 9 Step by step guide for enable Encryption for MBUS3 Slave 1 Update Slave with same encryption key as the Master to slave register 1 2 Enable encryption in the Concentrator Install Emulator Flag Register 1 see figure 10 02008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 10 of 12 Radiocraits Embedded Wireless Solutions MBUS DEMO Figure 13 shows MBUS2 Encryption key generator Tab Select to get a default If Master select installed Update Master slave with key slave register test key for master and slave Update Slave with key Bl MBUS DEMO 1 33 J oe ee ee Module Quick setup MBUS Packet Generator MBUS Packet sniffer Concentrator Install Emulator Encryption Key Generator Random Encrypten Key Generator Write Master Key to module Master Key Use Default Test Key set Installation register 00112233445566778899AABBCCDDEEFF 1 Add Slave Key to message list Slave Default Key Use Module Factory Default FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF enter packet name her Slave Key 0A980E5B74D2807A651F698AC0896A08F6 Write Slave Key to Module TUWUUUUUUUUUUSUUUUUUUCUUUUUUUUUUUUUUUS Calculate Key Set Enable Encryption Radiocrafts Option to add Slave key to packet list in the packet generator tab Usefull if you want to Slave encryption enable If Calculates a random Master enable encryption in the C
16. nd configure basic MBUS configuration parameters on the connected Demo Board The input entry selections and status information will be updated when you read the configuration from the module A read back from the module should be the first thing to do after connect to the COM port Some of the input entries are not valid for all MBUS feature set and they will be greyed out or hidden based on the read back information Figure Update module setting MBUS mode and ID based on input entry status information selection based on module read Ed MBUS DEMO 1 33 MBUS3 CONNECTED iv Start A eset STATUS Master T1 Idle ID O0CAE 12345678 01 07 Module Quick setup MBUS Packet Generator MBUS Packe sniffer Concentrator Install Emulator Encryption Key Generator Network role MBUS Mode Radiocrafts Wireless MBUS Module O Slave Master Os OR Rad Repeater Osi Embedded Wireless Solutions Install Mode Normal Install Accept All Other settings Auto sleep FJ Enable RSSI Of After TX E Clear installed meters After TX or RX E Enable LED Control Mailbox v acsm O acme v MBSM MA MBUS ID and Address field Module Details C4ield M4ield Adield MBUS Feature set MBUS3 06 12345678 Hardware revision 2 00 Firmware revision 3 08 Input entry selections Read module setting to store in module and update input entry Connected mo
17. onsentrator Emulator Master and Slave key on each button click include the slave key in a message from a Master Figure 13 MBUS2 Encryption Key Generator Step by step guide for enable Encryption for MBUSS Master 4 Install a meter to a register 1 8 5 Calculate an encryption key and update Master with key to installed slave register 6 Enable encryption in the Concentrator Install Emulator see figure 8 Step by step guide for enable Encryption for MBUS3 Slave 3 Update Slave with the encrypted Master Key 4 Enable encryption in the Encryption Key Generator tab 02008 Radiocrafts AS MBUS DEMO User Manual rev 1 30 Page 11 of 12 Radiocrafts Embedded Wireless Solutions MBUS DEMO Document Revision History New Revision Upgraded with MBUS2 feature set functions MBUS DEMO rev 1 10 Upgrades with MBUS3 features MBUS DEMO 1 33 Disclaimer Radiocrafts AS believes the information contained herein is correct and accurate at the time of this printing However Radiocrafts AS reserves the right to make changes to this product without notice Radiocrafts AS does not assume any responsibility for the use of the described product neither does it convey any license under its patent rights or the rights of others The latest updates are available at the Radiocrafts website or by contacting Radiocrafts directly As far as possible major changes of product specifications and functionality will be stated in produc
18. t specific Errata Notes published at the Radiocrafts website Customers are encouraged to check regularly for the most recent updates on products and support tools Trademarks RC232 is a trademark of Radiocrafts AS The RC232 Embedded RF Protocol is used in a range of products from Radiocrafts The protocol handles host communication data buffering error check addressing and broadcasting It supports point to point point to multipoint and peer to peer network topologies All other trademarks registered trademarks and product names are the sole property of their respective owners Life Support Policy This Radiocrafts product is not designed for use in life support appliances devices or other systems where malfunction can reasonably be expected to result in significant personal injury to the user or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness Radiocrafts AS customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Radiocrafts AS for any damages resulting from any improper use or sale 2010 Radiocrafts AS All rights reserved Contact Information Web site www radiocrafts com Address Radiocrafts AS Sandakerveien 64 NO 0484 OSLO NORWAY Tel 47 4000 5195 Fax 47 22 71 29 15 E mails rad
Download Pdf Manuals
Related Search
MBUS Demo_User_Manual