Home

Body of Model Trailer User`s Manual

Contents

1. Rim type designation This means the industry of manufacturer s designation for a rim by style or code Rim width This means the nominal distance between rim flanges Section width The linear distance between the exteriors of the sidewalls of an inflated tire excluding elevations due to labeling decoration or protective bands Sidewall That portion of a tire between the tread and bead Sidewall separation The parting of the rubber compound from the cord material in the sidewall Special Trailer ST tire The ST is an indication the tire is for trailer use only Test rim The rim on which a tire is fitted for testing and may be any rim listed as appropriate for use with that tire Tread That portion of a tire that comes into contact with the road Tire Safety Information Tread rib A tread section running circumferentially around a tire Tread separation Pulling away of the tread from the tire carcass Treadwear indicators TWI The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread Vehicle capacity weight The rated cargo and luggage load plus 68 kilograms 150 lbs times the vehicle s designated seating capacity Vehicle maximum load on the tire The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two Vehicle normal load on the tire The load on
2. VIN The Vehicle Identification Number VEHICLE TYPE Generally the word trailer is used However after this you may put a Model or additional descriptor 30 Coupling to Tow Information Tow Vehicle When equipping a new vehicle or an older vehicle to tow your trailer ask the vehicle dealer for advice on how to outfit the towing vehicle Discuss the following information and equipment with the vehicle dealer Overall Carrying and Towing Capacity of Vehicle Vehicle manufacturers will provide you with the maximum towing capacities of their various models as well as the GCWR No amount of reinforcement will give a 100 horsepower 2 500 pound truck the towing capacity that a 300 horsepower 5 000 pound truck has Towing Hitch The towing hitch attached to your tow vehicle must have a capacity equal to or greater than the load rating of the trailer you intend to tow The hitch capacity must also be matched to the tow vehicle capacity Suspension System A tow vehicle equipped with a factory installed Towing Package likely comes equipped with heavy duty springs heavy duty tires and other suspension components which are able to serve the size and weight of the trailer that the vehicle is rated to tow However the addition of additional equipment may further improve the tow vehicle performance These may include adjustable air shocks helper springs etc Brake Controller The brake controller is part of the tow vehicle and
3. Break Away Box Caja Break Away Bo tier Break Away Note Wire By Function Only Color Coding Nota Instale el cableado por su funci n Remarque C bler uniquement selon is Not Standard Among Manufacturers solamente C digo de color no es la les fonctions Le code de couleur peut norma entre todos los fabricantes varier d un constructeur l autre The breakaway brake system may be fitted with a charging facility that draws power from the tow vehicle If the electrical system on your tow vehicle does not 48 Coupling to Tow Information provide power to the breakaway brake battery you must periodically charge the battery on the trailer to keep the breakaway brake system in working order Visually inspect the breakaway brake system for broken parts Connect the pullpin cable to the tow vehicle so that the pullpin will be pulled out before all of the slack in the safety chains is taken up see Safety Chains figure Do not connect the pullpin cable to a safety chain or a safety chain receiver or to the gooseneck ball or its support This would keep the breakaway brake system from operating when it is needed Contact the hitch manufacturer or installer if you are not certain of the hitch provisions for breakaway brake connection To check the break away brake battery pull out the pullpin from the switch and attampt to pull the trailer forward You should feel the trailer resisting being towed but the wheels will not
4. 2 STEPS FOR DETERMINING CORRECT LOAD LIMIT TOW VEHICLE 7 Locate the statement The combined weight of occupants and cargo should never exceed XXX Ibs on your vehicle s placard 8 Determine the combined weight of the driver and passengers who will be riding in your vehicle 17 Tire Safety Information 9 Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds 10 The resulting figure equals the vailable amount of cargo and luggage capacity For example if the XXX amount equals 1400 Ibs and there will be five 150 Ib passengers in your vehicle the amount of available cargo and luggage capacity is 650 Ibs 1400 750 5 x 150 650 Ibs 11 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage capacity calculated in Step 4 12 If your vehicle will be towing a trailer load from your trailer will be transferred to your vehicle Consult the tow vehicle s manual to determine how this weight transfer reduces the available cargo and luggage capacity of your vehicle 2 3 L ARY OF TIRE TERMINOL Y Accessory weight The combined weight in excess of those standard items which may be replaced of automatic transmission power steering power brakes power windows power seats radio and heater to the extent that these items are available as factory installed equipmen
5. Next number This three digit number gives the width in millimeters of the tire from sidewall edge to sidewall edge In general the larger the number the wider the tire Next number This two digit number known as the aspect ratio gives the tire s ratio of height to width Numbers of 70 or lower indicate a short sidewall for improved steering response and better overall handling on dry pavement R The R stands for radial Radial ply construction of tires has been the industry standard for the past 20 years Next number This two digit number is the wheel or rim diameter in inches If you change your wheel size you will have to purchase new tires to match the new wheel diameter Next number This two or three digit number is the tire s load index It is a measurement of how much weight each tire can support You may find this information in your owner s manual If not contact a local tire dealer Note You may not find this information on all tires because it is not required by law M S The M S or M S indicates that the tire has some mud and snow capability Most radial tires have these markings hence they have some mud and snow capability 25 Tire Safety Information Speed Rating The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time The ratings range from 99 miles per hour mph to 186 mph These ratings are listed below Note You may not find this information on all tir
6. ONIS TRAILERS ALL MODELS A WARNING This Users Manual contains safety information and instructions for your trailer You must read this manual before loading or towing your trailer You must follow all safety precautions and instructions Walton Trailers 150 West 2500 North P O Box 6187 Logan UT 84341 6187 435 753 5444 Phone 435 753 5557 Facsimile www waltontrailers com Table of Contents 1 GENERAL SAFETY INFORMATION cccccsseeeesseeeeeeseeeeeeesees 1 1 1 SAFETY ALERT SYMBOLS AND SIGNAL WORDS eee 1 1 2 MAJOR HAZARDS 2 85 ctleees EH 2 1 2 1 Improper Sizing of the Trailer to the Tow Vehicle 2 1 2 2 Driving ToO Fast ie Iit 3 1 2 3 Failure to Adjust Driving Behavior When Towing a Trailer 3 1 2 4 Trailer Not Properly Coupled to the Hitch sssss 4 1 2 5 Proper Use of Safety Chains sse 5 1 2 6 Proper Connection of Breakaway Brake suus 5 1 2 7 Matching Trailer and Hitch seen 6 1 2 8 Worn Tires Loose Wheels and Lug Nuts sss 6 1 2 9 improper Loading siisii via chock eee ted eee eunte reg 1 2 10 Unsafe Load Distribution 1 2 11 Shifting Cargo 1 2 12 Inappropriate Cargo ssssssssssseee eene 1 2 18 Inoperable Brakes Lights or Mirrors seeessssss 10 1 2 14 Hazard
7. Section 2 4 contains information from the NHTSA brochure entitled Tire Safety Everything Rides On It This brochure describes the following items e Tire labeling including a description and explanation of each marking on the tires and information about the DOT Tire Identification Number TIN e Recommended tire inflation pressure including a description and explanation of A Cold inflation pressure B Vehicle Placard and location on the vehicle C Adverse safety consequences of under inflation including tire failure D Measuring and adjusting air pressure for proper inflation e Tire Care including maintenance and safety practices e Vehicle load limits including a description and explanation of the following items A Locating and understanding the load limit information total load capacity and cargo capacity B Calculating total and cargo capacities with varying seating configurations including quantitative examples showing illustrating how the vehicles cargo and luggage capacity decreases as combined number and size of occupants increases This item is also discussed in Section 3 C Determining compatibility of tire and vehicle load capabilities D Adverse safety consequences of overloading on handling and stopping on tires 16 Tire Safety Information 2 1 STEPS FOR DETERMINING CORRECT LOAD LIMIT TRAILER Q TIRE AND LOADING INFORMATION The weight of cargo should never exceed XXX kg
8. Tongue weight and weight distribution set up Doors and gates latched and secured Fire extinguisher Flares and reflectors 5 2 MAKE REGULAR STOPS After each 50 miles or one hour of towing stop and check the following items Coupler secured Safety chains are fastened and not dragging Cargo secured Cargo door latched and secured 68 Breaking In a New Trailer 6 BREAKING IN A NEW TRAILER 6 1 RETIGHTEN LUG NUTS AT FIRST 10 25 amp 50 MILES Wheel lugs can shift and settle quickly after being first assembled and must be checked after the first 10 25 and 50 miles of driving Failure to perform this check may result in a wheel coming loose from the trailer causing a crash leading to death or serious injury A WARNING Lug nuts are prone to loosen after initial installation which can lead to death or serious injury Check lug nuts for tightness on a new trailer or when wheel s have been remounted after the first 10 25 and 50 miles of driving See Section 8 2 11 2 page 82 on Proper Tourqing Technique 6 2 ADJUST BRAKE SHOES AT FIRST 200 MILES Brake shoes and drums experience a rapid initial wear The brakes must be adjusted after the first 200 miles of use and each 3 000 miles thereafter Some axles are fitted with a mechanism that will automatically adjust the brake shoes when the trailer is hard braked from a rearward direction Read your axle and brake manual to see if your brakes adjust
9. dump walls if applicable and cross members excluding the floorboards and running gear Warranty is also void if the original design and intended use of the trailer has been modified changed or manipulated in any way without prior written authorization from the manufacturer POWDER COATING LIMITED WARRANTY Walton Trailers warrants its powder coating finish to be consistent with industry standards for one 1 year after the date of shipment from the manufacturing facility Warrantable powder coating repairs are limited to spot repairs and blending consistent with standards in the trailer industry NORMAL INTENDED USE NO REPAIRS OR ALTERATIONS This Limited Warranty covers only defects in original structural components which arise from normal intended use and does not apply if the trailer has been subject to negligence accident abuse misuse overloaded or has been repaired or altered without the prior written consent of Walton Trailers 85 TRANSPORTATION AND LOSS OF USE COSTS EXCLUDED Transportation of any trailer to and or from the factory or any other approved repair facility shall be the sole responsibility of the trailer owner Walton Trailers will not be liable for any such cost LOSS OF USE INCONVENIENCE LOSS OF TIME COMMERCIAL LOSS OR ANY OTHER TYPE OF DAMAGES GENERAL OR SPECIFIC FORSEEN OR UNFORSEEN SHALL NOT BE COMPENSATED BY Walton Trailers LLC DEALER RESPONSIBILITES The Authorized Walton dealer is responsi
10. USE AN ADEQUATE TOW VEHICLE AND HITCH If the vehicle or hitch is not properly selected and matched to the Gross Vehicle Weight Rating GVWR of your trailer you can cause an accident that could lead to death or serious injury If you already have a tow vehicle know your vehicle tow rating and Gross Combination Weight Rating GCWR and make certain the trailer s rated capacity is less than or equal to the tow vehicle s rated towing capacity If you already have or plan to buy a trailer make certain that the tow rating of the tow vehicle is equal to or greater than the GVWR of the trailer and that the GCWR will be within limits Use of a hitch with a load rating less than the load rating of the trailer can result in loss of control and may lead to death or serious injury Use of a tow vehicle with a towing capacity less than the load rating of the trailer can result in loss of control and may lead to death or serious injury Be sure your hitch and tow vehicle are rated for the Gross Vehicle Weight Rating of your trailer 3 1 1 TRAILER INFORMATION Certification VIN Label The location of the trailers Certification VIN Tag is shown below IN Ta OCated on the Drivers Side Front 29 Coupling to Tow Information MFD BY JRW TRAILERS DBA WALTON TRAILERS GVWR COLD INFLATION PRESSURE GAWR TIRE RIM KPA PSI SGL DUAL FRONT REAR THIS VEHICLE CONFROMS TO ALL APPLICABLE US FEDERAL MOTOR VEHICLE SAFETY STA
11. esses 24 2 4 9 Tire Riepalr ice oto tO P EE OR 24 2 4 10 Tire Fundamentals aisi enne 24 2 4 10 1 Information on Passenger Vehicle Tires 25 2 4 10 2 UTQGS Information sii 3 inne ete nets 26 2 4 11 Tire Safely Tips te ae PRO eit eee 28 3 COUPLING TO THE TOW VEHICLE esses 29 4 T Table of Contents 3 1 USE AN ADEQUATE TOW VEHICLE AND HITCH eene 29 3 1 1 Trailer Information eesssssissssssss seen 29 3 2 COUPLING AND UNCOUPLING THE TRAILER eene 32 3 2 1 Various Coupler Designs ssesssseseee eene 34 3 2 2 Trailer with Ball Hitch Coupler senes 34 3 2 2 1 Before coupling the trailer to the tow vehicle 35 3 2 2 2 Prepare the coupler and hitch esseeeeeessssss 36 3 2 2 8 Couple the trailer to the tow vehicle se 37 3 2 2 4 Rig the safety chains sse 38 3 2 2 5 Attach and test electric breakaway brake system 39 3 2 2 6 Connect the electrical Cables cccsscceeesseeeestteeessees 40 3 2 2 7 Uncoupling the Ball Hitch Trailer with Tongue Jack 41 3 2 3 Trailer with Gooseneck Coupler and Drop leg Jack 41 3 2 3 1 Prepare the ball receiver and gooseneck ball 45 3 2 3 2 Couple the trailer to t
12. or XXX Ibs COLD TIRE PRESSURE SEE OWNER S 621KPA 90PSI MANUAL FOR ADDITIONAL INFORMATION Tire and Loading information Placard Figure 1 1 2 1 1 TRAILERS 1 Pounps GVWR on LE 1 Locate the statement The weight of cargo should never exceed XXX kg or XXX Ibs on your vehicle s placard See figure 1 1 2 This figure equals the available amount of cargo and luggage load capacity 3 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage load capacity The trailer s placard refers to the Tire Information Placard attached adjacent to or near the trailer s VIN Certification label at the left front of the trailer Note The following calculations in Sections 2 1 2 and 2 2 are not required by the government For the purpose of completeness NATM has included these statements 2 1 2 TRAILERS OVER 10 000 PouuNps GVWR NOTE THESE TRAILERS ARE NOT REQUIRED TQ HAVE A TIRE INFORMATION PLACARD ON THE VEHICLE 4 Determine the empty weight of your trailer by weighing the trailer using a public scale or other means This step does not have to be repeated 5 Locate the GVWR Gross Vehicle Weight Rating of the trailer on your trailer s VIN Certification label 6 Subtract the empty weight of your trailer from the GVWR stated on the VIN label That weight is the maximum available cargo capacity of the trailer and may not be safely exceeded
13. The table below has rules of thumb for proper tongue weight In the table below the second column notes the rule of thumb percentage of total weight of the trailer plus its cargo Gross Vehicle Weight or GVW that should appear on the tongue of the trailer For example a trailer with a gooseneck hitch with a loaded weight of 12 000 pounds should have 20 25 of 12 000 pounds on the tongue That is the example trailer would have 2 400 to 3 000 pounds on its tongue Tongue Weight as a Percentage of Loaded Trailer Weight Type of Hitch 10 15 for large trailers Ball Hitch or Bumper Hitch 6 10 for smaller utility and cargo trailers 4 6 for boat trailers Gooseneck Hitch 20 25 Fifth Wheel Hitch 20 25 The numbers quoted above are for example purposes only and should be tailored to the specific trailer For questions regarding the actual percent of tongue weight for the trailer check with the manufacturer for specifics 54 Loading the Trailer WARNING Improper tongue weight load distribution can result in loss of control of the trailer leading to death or serious injury Make certain that tongue weight is within the allowable range Be sure to e Distribute the load front to rear to provide proper tongue weight see chart e Distribute the load evenly right and left to avoid tire overload and e Keep the center of gravity low 4 2 CHECKING TONGUE WEIGHT To check the tongue weight the tow
14. Tire Warning UT1016 Coupler Instructions UT1020 Safety Chains UT1026 Electrical Connections UTO0017 Proper Loading UT1014 Breakaway A WARNING To protect you and others against death or serious injury all of the labels shown above must be on the trailer and must be legible If any of these labels are missing or cannot be read call Walton Trailers at 435 753 5444 for free replacement labels You will need to provide us with the number shown at the bottom of the label s in order for us to send the correct one s The following labels are used on Walton Trailers Due to difference in trailer models and equipment your trailer may or may not use all decals 12 General Safety Information A CAUTION icc Coupler hitch and tralerballarethe Tit pin is latched Heavy end of toad must go onto the You are required to comply with local same size Wheel lug bolts are property tightened trailer frst Serious injury and or property Coupler is latched Tires are nfiated to pressure When approaching trailer deve on ANd state requirements regarding brakes licensing and any additional Safety chains are criss croesed ndcated on wre slowly equipment that may be necessary damage can result if this vehicle is under tongue and hitched to towing Trailer brakas if trailer is so High speed loading can resuit in towed before familiarizing yourself eve empero diete wm uc sae i As traer lighting is
15. an individual tire that is determined by distributing to each axle its share of the curb weight accessory weight and normal occupant weight distributed in accordance with Table of CRF 49 571 110 and dividing by 2 Weather side The surface area of the rim not covered by the inflated tire Wheel center member In the case of a non pneumatic tire assembly incorporating a wheel a mechanical device which attaches either integrally or separably to the non pneumatic rim and provides the connection between the non pneumatic rim and the vehicle or in the case of a non pneumatic tire assembly not incorporating a wheel a mechanical device which attaches either integrally or separably to the non pneumatic tire and provides the connection between tire and the vehicle Wheel holding fixture The fixture used to hold the wheel and tire assembly securely during testing 24 TIRE SAFETY EVERYTHING RIDE NIT The National Traffic Safety Administration NHTSA has published a brochure DOT HS 809 361 that discusses all aspects of Tire Safety as required by CFR 575 6 This brochure is reproduced in part below It can be obtained and downloaded from NHTSA free of charge from the following web site http www nhtsa dot gov cars rules TireSafety ridesonit tires_index html Studies of tire safety show that maintaining proper tire pressure observing tire and vehicle load limits not carrying more weight in your vehicle than you
16. automatically If you do not have the axle and brake manual call Walton Trailers at 435 753 5444 for a free copy A hard stop is used to e Confirm that the brakes work e Confirm that the trailer brakes are properly synchronized with the tow vehicle brakes using the brake controller in the tow vehicle e Adjust the brake shoes as necessary e For surge brakes check the Master cylinder reservoir for fluid If your trailer is not fitted with automatically adjusting brakes the brakes will need to be manually adjusted See section 8 2 4 2 Manually Adjusting Brake Shoes for instructions 6 3 SYNCHRONIZING THE BRAKE SYSTEMS Trailer brakes are designed to work in synchronization with the brakes on the tow vehicle When the tow vehicle and trailer braking systems are synchronized both braking systems contribute to slowing and the tongue of the trailer will neither dive nor rise sharply 69 Breaking In a New Trailer A WARNING If trailer and tow vehicle brakes do not work properly together death or serious injury can occur Road test the brakes in a safe area at no more than 30 m p h before each tow To insure safe brake performance and synchronization read and follow the axle brake and the brake controller manufacturers instructions If you do not have these instructions call Walton Trailers at 435 753 5444 for a free copy TIRE PRESSURE Check tire pressures on both the trailer and tow vehicle Infl
17. clearance lights for proper operation A WARNING Improper operating taillights stoplights and turn signals can cause collisions Check all lights before each tow 79 Inspection Service amp Maintenance 8 2 8 Accessory BATTERY Your trailer may be outfitted with an accessory battery that operates lighting electric landing gear slide outs or other accessories An accessory battery may be kept charged either by the tow vehicle or by the generator or shore power See the manual for the accessory battery A disconnect switch may be provided to disconnect the accessory battery when you do not plan to be using the trailer for an extended period such as seasonal storage If there is no disconnect switch then remove the cables from the battery terminals The accessory battery must be kept in a charged condition during storage The battery could freeze and break if it becomes discharged 8 2 9 TIRES Trailer tires may be worn out even though they still have plenty of tread left This is because trailer tires have to carry a lot of weight all the time even when not in use It is actually better for the tire to be rolling down the road than to be idle During use the tire releases lubricants that are beneficial to tire life Using the trailer tires often also helps prevent flat spots from developing The main cause of tire failure is improper inflation Check the cold tire inflation pressures at least once a week for proper
18. completely dry before replacing the rubber mat 8 2 2 1 Fasteners and Frame Members Inspect all of the fasteners and structural frame members for bending and other damage cracks or failure Repair or replace any damaged fastener and repair the frame member If you have any questions about the condition or method of repair of fasteners or frame members get the recommendation of or have the repair done by your dealer The various fastener types used on your trailer are e Bolts which are used mainly for attaching door and gate hinges to the trailer body e Buck Rivets which are used to attach the sides and roof panels of the body to each other and to the frame of the trailer and 74 Inspection Service amp Maintenance A WARNING Broken or damaged fasteners or welds can cause injury or damage to trailer and contents Inspect for and repair all damaged parts at least once a year 8 2 2 2 Welds All welds can crack or fail when subjected to heavy loads or movement of cargo that was not properly tied to prevent movement Any time that you know or suspect that the trailer has been subjected to heavy loads or movement of cargo immediately inspect the welds and fasteners for damage To prevent severe damage to your trailer inspect all of the welds for cracks or failure at least once a year A WARNING Improper weld repair will lead to early failure of the trailer structure and can cause serious injury or death
19. correctly break away device is attached to resu in injury with the instructions in the owners Londra is secured to rader front and towing vehicie Wet surfaces may cause slick bed Load is within traer capacity and surface manual and cautions listed to the eem jack if trailer is equipped distributed property to martin Use caution while toading on wet right is retracted proper tongue weight bed US3023 AWARNING Tilt fraler before CHECK WHEEL LUGS loading or unloading On first trip tighten wheel lugs at start and Do not transport with at 10 25 and 50 miles Tighten to load positioned behind manufacturer s specifications this point Thereafter check wheel lugs before each trip after excessive braking and following winter storage Contact your state motor vehicle department for more information UTO006 AWARNING Coupler will fall if all bolts and keeper pins are removed at the same time Deck latch must be unlocked before tilting trailer Lock latch before transporting 1 2 17 TRAILER TOWING GUIDE Driving a vehicle with a trailer in tow is vastly different from driving the same vehicle without a trailer in tow Acceleration maneuverability and braking are all diminished with a trailer in tow It takes longer to get up to speed you need more room to turn and pass and more distance to stop when towing a trailer You will need to spend time adjusting to the d
20. inner and outer bearings are to be replaced at the same time e Replace seals that have nicks tears or wear e Lubricate the bearings with a high quality EP 2 automotive wheel bearing grease Every time the wheel hub is removed and the bearings are reassembled follow the steps below to check the wheel bearings for free running and adjust e Turn the hub slowly by hand while tightening the spindle nut until you can no longer turn the hub by hand e Loosen the spindle nut just until you are able to turn it the spindle nut by hand Do not turn the hub while the spindle nut is loose e Putanew cotter pin through the spindle nut and axle e Check the adjustments Both the hub and the spindle nut should be able to move freely the spindle nut motion will be limited by the cotter pin 8 2 11 2 Lug Nuts Bolts Being sure wheel mounting nuts lug nuts on trailer wheels are tight and properly torqued is an important responsibility that trailer owners and users need to be familiar with and practice Inadequate and or inappropriate wheel nut torque tightness is a major reason that lug nuts loosen in service Loose lug nuts can rapidly lead to a wheel separation with potentially serious safety consequences Lug nuts are prone to loosen right after a wheel is mounted to a hub When driving on a new or remounted wheel check the lug nut tightness often during 82 Inspection Service amp Maintenance the first few hundred miles of th
21. leading to death or serious injury if the coupler or ball hitch fails Connect the breakaway cable to the tow vehicle and NOT to the hitch ball or support Before towing the trailer test the function of the breakaway brake System If the breakaway brake system is not working do not tow the trailer Have it serviced or repaired Do not tow the trailer with the breakaway brake system ON because the brakes will overheat which can result in permanent brake failure A WARNING Failure to replace the pullpin will prevent brakes from working leading to loss of control serious injury or death If you do not use your trailer for three or more months or during winter months e Store the battery indoors and e Charge the battery every three months Replace the breakaway brake battery according to the intervals specified by battery manufacturer 3 2 2 6 Connect the electrical cables Connect the trailer lights to the tow vehicle s electrical system using the electrical connectors Check all lights for proper operation Clearance and Running Lights Turn on tow vehicle headlights Brake Lights Step on tow vehicle brake pedal Turn Signals Operate tow vehicle directional signal lever Check electric brakes for proper operation using brake controller mounted in the cab If your trailer has electric brakes your tow vehicle will have an electric brake controller that sends power to the trailer brakes Before towin
22. terms of this Limited Warranty and will not pay charges in excess of these amounts DISCLAIMERS THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESS WARRANTIES AND REPRESENTATIONS WALTON TRAILERS MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND EXPRESS OR IMPLIED WITH RESPECT TO WALTON TRAILERS WHETHER AS TO MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER NO AUTHORIZED WALTON TRAILER DEALER IS AUTHORIZED TO MAKE FURTHER OR ADDITIONAL WARRANTIES ON BEHALF OF WALTON TRAILERS LLC 87 ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR INTENDED USE ARE LIMITED TO WARRANTY PERIODS STATED ABOVE 88
23. the coupler is locked to the hitch Overloading can damage the tongue jack Do not use the tongue jack to raise the tow vehicle more than 1 inch If the coupler cannot be secured to the hitch ball do not tow the trailer Call Walton Trailers at 435 753 5444 or your dealer for assistance Lower the trailer so that its entire tongue weight is held by the hitch and continue retracting the jack to its fully retraced position 37 Coupling to Tow Information 3 2 2 4 Rig the safety chains Safety Chain Arrangement Bumper Pull Trailer ATTACH HOOKS TOTOW VEHICLE FRAME ALWAYS use safety chains Chains hold trailer if connection fails You must 1 CROSS chains underneath coupler 2 ALLOW slack for trailer to turn Y Y ENOUGH SLACK 3 ATTACH chain hooks securely to tow Oe FOR TURNS vehicle frame CROSS CHAINS 2002 NATM UTO020 Visually inspect the safety chains and hooks for wear or damage Replace worn or damaged safety chains and hooks before towing Rig the safety chains so that they Cris cross underneath the coupler so if the trailer uncouples the safety chains can hold the tongue up above the road Loop around a frame member of the tow vehicle or to holes provided in the hitch system but do not attach them to an interchangeable part of the hitch assembly Attach S hooks up from underneath the hole do not just drop into hole and Provide enough slack to permit tight turns but not
24. the load properly To determine that you have loaded the trailer within its rating you must consider the distribution of weight as well as the total weight of the trailer and its contents The trailer axles carry most of the total weight of the trailer and its contents Gross Vehicle Weight or GVW The remainder of the total weight is carried by the tow vehicle hitch It is essential for safe towing that the trailer tongue and tow vehicle hitch carry the proper amount of the loaded trailer weight otherwise the trailer can develop an undesirable sway at towing speeds or the rear of the towing vehicle can be overloaded Read the Tongue Weight section below The load distribution must be such that no component part of the trailer is loaded beyond its rating This means that you must consider the rating of the tires wheels and axles For tandem and triple axle trailers you must make sure that the front to rear load distribution does not result in overloading any axle Towing stability also depends on keeping the center of gravity as low as possible Load heavy items on the floor and over the axles When loading additional items be sure to maintain even side to side weight distribution and proper tongue weight The total weight of the trailer and its contents must never exceed the total weight rating of the trailer Gross Vehicle Weight Rating or GVWR A WARNING An overloaded trailer can result in loss of control of the trail
25. to death or serious injury Be sure the LOAD RATING of the hitch ball is equal or greater than the load rating of the coupler Be sure the SIZE of the hitch ball matches the size of the coupler Wipe the hitch ball clean and inspect it visually and by feel for flat spots cracks and pits A WARNING A worn cracked or corroded hitch ball can fail while towing and may result in death or serious injury Before coupling trailer inspect the hitch ball for wear corrosion and cracks Replace worn or damaged hitch ball Rock the ball to make sure it is tight to the hitch and visually check that the hitch ball nut is solid against the lock washer and hitch frame Wipe the inside and outside of the coupler clean and inspect it visually for cracks and deformations feel the inside of the coupler for worn spots and pits Be sure the coupler is tight to the tongue of the trailer All coupler fasteners must be visibly solid against the trailer frame 35 Coupling to Tow Information A WARNING A loose hitch ball nut can result in uncoupling leading to death or serious injury Be sure the hitch ball is tight to the hitch before coupling the trailer Raise the bottom surface of the coupler to be above the top of the hitch ball Use the jack if one is provided otherwise use wood or concrete blocks to support the trailer tongue 3 2 2 2 Prepare the coupler and hitch Lubricate the hitch ball and the inside of th
26. to recheck and adjust the tire s pressure when you can obtain a cold reading 2 4 6 TIRE SIZE To maintain tire safety purchase new tires that are the same size as the vehicle s original tires or another size recommended by the manufacturer Look at the tire information placard the owner s manual or the sidewall of the tire you are replacing to find this information If you have any doubt about the correct size to choose consult with the tire dealer 2 4 7 TIRE TREAD The tire tread provides the gripping action and traction that prevent your vehicle from slipping or sliding especially when the road is wet or icy In general tires are not safe and should be replaced when the tread is worn down to 1 16 of an inch Tires have built in treadwear indicators that let you know when it is time to replace your tires These indicators are raised sections spaced intermittently in the bottom of the tread grooves When they appear even with the outside of the tread it is time to replace your tires Another method for checking tread depth is to place a penny in the tread with Lincoln s head upside down and facing you If you can see the top of Lincoln s head you are ready for new tires 2 4 8 TIRE BALANCE AND WHEEL ALIGNMENT To avoid vibration or shaking of the vehicle when a tire rotates the tire must be properly balanced This balance is achieved by positioning weights on the wheel to counterbalance heavy spots on the wheel and tire assembly A
27. vehicle if the trailer comes loose 3 2 3 4 Attach and test the breakaway brake system If the coupler or hitch fails a properly connected and working breakaway brake system will apply electric brakes on the trailer The safety chains will keep the tow vehicle attached and as the brakes are applied at the trailer s axles the trailer tow vehicle combination will come to a controlled stop The breakaway brake system includes a battery a switch with a pullpin and a breakaway brake controller Read and follow the instructions here as well as the instructions that have been prepared by the breakaway brake controller manufacturer If you do not have these instructions call Walton Trailers at 435 753 5444 for a free copy Breakaway Brake System Gooseneck Coupler DIAGRAM WITH CHARGER DIAGRAMA CON EL CARGADOR DIAGRAMME AVEC CHARGEUR Electric Brake Blue Ground White Freno El ctrico Azul Conexion a Tierra Blanco Frein lectrique Bleu Masse Blanc r i I DM 12 Volt Battery Lead Black or Red Black gt Conductor de bateria Negro de 12 voltios Negro o Rojo Noi Conducteur de batterie de po C 12 volts Roir ou Rouge White Blanco Blanc Break Away Switch A Interruptor Break Away Blue Interrupteur Break Away Azul Wl 8 C and D are splices Bleu A B C y D son empalmes A B C et D sont des pissures Cable Cable C ble
28. wheel alignment adjusts the angles of the wheels so that they are positioned correctly relative to the vehicle s frame This adjustment maximizes the life of your tires These adjustments require special equipment and should be performed by a qualified technician 2 4 9 TIRE REPAIR The proper repair of a punctured tire requires a plug for the hole and a patch for the area inside the tire that surrounds the puncture hole Punctures through the tread can be repaired if they are not too large but punctures to the sidewall should not be repaired Tires must be removed from the rim to be properly inspected before being plugged and patched 2 4 10 TIRE FUNDAMENTALS Federal law requires tire manufacturers to place standardized information on the sidewall of all tires This information identifies and describes the fundamental characteristics of the tire and also provides a tire identification number for safety standard certification and in case of a recall 24 Tire Safety Information 2 4 10 1 Information on Passenger Vehicle Tires Please refer to the diagram below Radial l alena Ratio of height to width aspect ratio Load index amp Nominal width of speed symbol tire in millimeters U S DOT tire identification number Passenger car tire Severe snow conditions Tu PET aon e t ERS Co Treadwear traction and temperature grades pem load rating P The P indicates the tire is for passenger vehicles
29. Do not repair cracked or broken welds unless you have the skills and equipment to make a proper repair If not have the welds repaired by your dealer 8 2 3 Drop Ramp TORSION SPRINGS If your trailer has a drop ramp door the weight of the door may be partially held by a torsion spring and a cable Stand to the side when opening the drop ramp You could be hurt if you are behind the drop ramp and the counterbalance does not work Inspect the cable and cable ends regularly for fraying and signs of loosening If released a torsion spring can inflict serious injury The torsion spring and cable are not user serviceable The torsion spring must be serviced by a person who is trained in torsion spring safety 8 2 4 TRAILER BRAKES 8 2 4 1 Brake Shoes and Drums Properly functioning brake shoes and drums are essential to ensure safety You must have your dealer inspect these components at least once per year or each 12 000 miles The brake shoes must be adjusted after the first 200 miles of use and each 3 000 miles thereafter Most axles are fitted with a brake mechanism that will automatically adjust the brake shoes when the trailer is hard braked from a rearward direction Read your axle and brake manual to see how to adjust your 75 Inspection Service amp Maintenance brakes If you do not have this manual call Walton Trailers at 435 753 5444 for a free copy 8 2 4 2 Manually Adjusting Brake Shoes Some braking syst
30. Drop Leg Mechanism figure 46 Coupling to Tow Information Drop The drop legs are heavily spring loaded in the lowered position They will rapidly return to the upper position when released and can inflict serious bruises scrapes or pinching Keep your feet shins and hands well clear of the drop legs and drop leg bases when releasing the drop legs Always wear shoes or boots while performing this operation 3 2 3 3 Rig the safety chains Visually inspect the safety chains and hooks for wear or damage Replace worn or damaged safety chains and hooks before towing Rig the safety chains so that they attach to the safety chain receivers in the bed of the truck If you are not certain of the hitch provisions for receiving safety chains contact the hitch manufacturer or installer Do NOT attach the safety chains to the gooseneck ball or its support and Rig the safety chains so they have sufficient slack to permit turning but not too much slack the safety chains must keep the gooseneck on the tow vehicle bed if the trailer uncouples 47 Coupling to Tow Information A WARNING Improper rigging of the safety chains can result in loss of control of the trailer and tow vehicle leading to death or serious injury if the trailer uncouples from the tow vehicle e Fasten chains to safety chain receivers on the hitch not to ball e Have sufficient slack to permit turning and to keep gooseneck on bed of tow
31. Manually Adjusting Brake Shoes sseesssss 76 8 2 4 8 Brakes Electric eeeeeesssseeeeeeeeeenennn n 76 8 2 4 4 Brakes Hydraulic vacuum air or electric operated 77 8 2 5 Trailer Connection to Tow Vehicle ccccccccccccccecececececeeeceeeeeseeees 78 8 2554 Coupler and Ball eee eee treten 78 8 2 5 2 00Sseriecle le ee Reeve eee eee v EI IIO 79 8 2 5 8 Fifth Wheel Kingpin cccccecceesseeceeeseeeeeeseeeessneeeessaees 79 8 2 6 Landing Leg or Jack eene 79 8 2 7 Lights and Signals coude etre 79 8 2 8 Accessory Battery cceccccceserccseesenenersenseesnesenenenneeseneneeeensenens 80 8 2 9 THOS it ei eo t dett tet o e m He P ee Sas 80 8 2 10 Wheel Rims eese 81 8 2 11 Wheels Bearings and Lug Nuts seen 81 8 2 11 1 Unsealed Bearings Hubs 81 8 2 11 2 Lug Nuts Bolts e erii AREE 82 9 LIMITED WARRANTY eene nnnm nana naa na nu aan aman 85 General Safety Information 1 GENERAL SAFETY INFORMATION 1 1 SAFETY ALERT SYMBOLS AND SIGNAL WORDS An Owner s Manual that provides general trailer information cannot cover all of the specific details necessary for the proper combination of every trailer tow vehicle and hitch Therefore you must read understand and follow the instructions given by the tow vehicle and trailer hitch manufacturers as well as the instructions in thi
32. NDARDS FMVSS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE V LN TYPE OF VEHICLE The trailer Certification VIN tag contains the following critical safety information for the use of your trailer MANUFACTURER Name of trailer manufacturer DATE OF MANUFACTURE Month and year the trailer was manufactured GVWR The Gross Vehicle Weight Rating is the maximum allowable gross weight of the trailer and its contents The gross weight of the trailer includes the weight of the trailer and all of the items within it such as cargo water food and other supplies GAWR The Gross Axle Weight Rating is the maximum gross weight that an axle can support It is the lowest of axle wheel or tire rating Sometimes the tire or wheel rating is lower than the axle manufacturers rating and will then determine GAWR The sum total of the GAWR for all trailer axles may be less than the GVWR for the trailer because some of the trailer load is carried by the tow vehicle rather than by the trailer axle s The total weight of the cargo and trailer must not exceed the GVWR and the load on an axle must not exceed its GAWR TIRE SIZE The tire size recommended for your trailer and load range PSIC The pounds per square inch cold is the tire pressure Kilopascals Pounds per Square Inch measured when Cold CERTIFICATION STATEMENT This trailer meets all the Federal Motor Vehicle Safety Standards in effect on the date of manufacture shown above
33. OMMENDED TIRE PRESSURE AND LOAD Limits Tire information placards and vehicle certification labels contain information on tires and load limits These labels indicate the vehicle manufacturer s information including Recommended tire size Recommended tire inflation pressure e Vehicle capacity weight VCW the maximum occupant and cargo weight a vehicle is designed to carry e Front and rear gross axle weight ratings GAWR the maximum weight the axle systems are designed to carry Both placards and certification labels are permanently attached to the trailer near the left front 2 4 3 UNDERSTANDING TIRE PRESSURE AND LOAD LIMITS Tire inflation pressure is the level of air in the tire that provides it with load carrying capacity and affects the overall performance of the vehicle The tire inflation pressure is a number that indicates the amount of air pressure measured in pounds per square inch psi a tire requires to be properly inflated You will also find this number on the vehicle information placard expressed in kilopascals kPa which is the metric measure used internationally Manufacturers of passenger vehicles and light trucks determine this number based on the vehicle s design load limit that is the greatest amount of weight a 22 Tire Safety Information vehicle can safely carry and the vehicle s tire size The proper tire pressure for your vehicle is referred to as the recommended cold inflation pressure As you w
34. OR MAINTAINING PROPER TIRE PRESSURE e Step 1 Locate the recommended tire pressure on the vehicle s tire information placard certification label or in the owner s manual Step 2 Record the tire pressure of all tires Step 3 If the tire pressure is too high in any of the tires slowly release air by gently pressing on the tire valve stem with the edge of your tire gauge until you get to the correct pressure e Step 4 If the tire pressure is too low note the difference between the measured tire pressure and the correct tire pressure These missing pounds of pressure are what you will need to add e Step 5 At a service station add the missing pounds of air pressure to each tire that is underinflated e Step 6 Check all the tires to make sure they have the same air pressure except in cases in which the front and rear tires are supposed to have different amounts of pressure 23 Tire Safety Information If you have been driving your vehicle and think that a tire is underinflated fill it to the recommended cold inflation pressure indicated on your vehicle s tire information placard or certification label While your tire may still be slightly underinflated due to the extra pounds of pressure in the warm tire it is safer to drive with air pressure that is slightly lower than the vehicle manufacturer s recommended cold inflation pressure than to drive with a significantly underinflated tire Since this is a temporary fix don t forget
35. Service each 6 Months or 6 000 Miles Item Inspection Service Manual Section Reference Tires Rotate 5 000 miles Section 8 2 9 Brakes electric Magnets Check wear and current draw Section 8 2 4 3 C Controller Check power output amperage in tow vehicle and modulation Section 8 2 4 3 B See Controller Mfr s Manual Structure Roof Vents Clean dirt buildup lubricate Section 8 2 2 Windows hinges and slides Inspect tread and sidewalls Section 8 2 9 Tires thoroughly Replace tire when treads are Section 8 2 9 worn when sidewall has a bulge or sidewall is worn Inspection and Service Each Year or 12 000 Miles Item Inspection Service Manual Section Reference Brakes all types gt Shoes and Check for scoring and wear Replace per manufacturer s Section 8 2 4 1 See Brake Mfr s Manual drums specifications Jack Drop leg Grease gears at top See Jack Mfr s Manual Structure Inspect all frame members Section 8 2 1 gt Frame members gt Welds bolts amp rivets Repair or replace damaged worn or broken parts Inspect all welds Repair as needed Section 8 2 2 2 Wheels gt Sealed Bearings Hubs gt UNSEALED Bearings Hubs gt Rims Check and confirm free running Replace if not sealed bearings are not serviceable Disassemble inspect assemble and repack Replace promptly if immersed in water Inspect for cracks amp dents R
36. UG BOLT 6 LUG BOLT 8 LUG BOLT PATTERN PATTERN PATTERN Keep a record of the date and approximate mileage when you check the lug nut torque Note any lug nut that has lost torque Investigate the reason s if the lug nut torque is not maintained after more than one re torque application because 83 Inspection Service amp Maintenance this indicates there is something wrong with the lug nuts nut studs wheels and or hubs and should be corrected Contact your dealer or vehicle manufacturer immediately if you experience any persistent lug nut loosening or any other lug wheel or axle problems In the event of a wheel separation incident notify the vehicle manufacturer and dealer Seek prompt professional assistance in assessing the trailer and its gear and retain but don t re use involved lugs wheels and studs Don t repair or service the trailer yourself Call a trained technician Lug Nut Torque Steel Wheels Axle Rating Dry Torque 3 500 to 7 000 Ye inch 80 to 95 8 000 9 16 inch 120 to 140 9 000 5 8 inch 175 to 225 10 000 5 8 inch flanged 275 to 325 12 000 34 inch flanged 375 to 425 Lug Nut Torque Aluminum Wheels A Dry Torque 15 inch 5 or 6 hole 65 to 75 16 inch 8 hole 65 to 75 Dry Torque Foot pounds is determined by manufacturer 84 9 LIMITED WARRANTY WALTON TRAILERS LLC LIMITED WARRANTY Walton Trailers LLC hereafter known as Walton Trailers is the manufacturer of the Walton b
37. ad on a soft or uneven surface may cause the trailer to overturn which can result in death or serious injury e For spreading material the surface in which the tow vehicle and trailer will travel MUST be firm and level 64 Loading the Trailer A WARNING A soft and or uneven surface may cause the tow vehicle and trailer to overturn when the dump body is raised or while spreading material Raise the dump body ONLY if the tow vehicle and trailer are both on a firm and level surface A WARNING An overloaded trailer or improperly distributed load can result in death or serious injury An overloaded trailer can cause the hydraulic system to malfunction resulting in the dump body falling A load that is improperly distributed in the trailer can result in the trailer overturning when the dump body is raised Set the metering chains at the desired number of links to control the opening distance of the spreader gate Be sure to set both chains at equal length Loaded materials can exert pressure against the spreader gate This may cause the spreader gate to swing out with force when unlatched causing serious injury Stand away from the trailer to unlatch spreader gate Unlatch spreader gate While using the dump body controller position yourself in a safe location clear of the dump body Check for overhead power lines and other obstructions before raising dump body 65 Loading the Trailer A WARNING Risk
38. ailer with the jack e Arrange a brick 2 x 4 or 4 x 4 board bathroom scale and pipes as shown in Checking Tongue Weight figure The brick should be about the same thickness as the bathroom scale e Leave a 3 foot distance between the pipes and place the coupler about 2 feet from the pipe on the bathroom scale e Place a strong block support such as a cement block on the board Note the weight indicated on the scale e Lower the tongue until the coupler rests on the block support and the jack is e inch above the ground e Subtract the scale reading with the block and board alone from the scale reading with the trailer on the block Multiply the result by 3 to get the actual tongue weight Example Scale reading with block and board alone 10 Ibs Scale reading with trailer coupler resting on board 50 Ibs Actual tongue weight 50 10 x 3 120 Ibs For heavier trailers it is easier to go to a truck stop where there is a certified scale Pull only the tow vehicle onto the scale and get the weight This weight must be less than your tow vehicle s GVWR Pull the trailer onto the scale and decouple it from the tow vehicle leaving just the trailer on the scale Get a ticket which lists the total trailer weight Re connect the trailer to your tow vehicle and the drive the tow vehicle wheels off the scale just leaving the trailer axles on the scale Get a second ticket which lists the trailer s axle weight Simple subt
39. ate to the maximum shown on the VIN Certification Label 70 Accessories 7 ACCESSORIES This chapter provides some basic information for the safe operation of several accessories For many accessories such as generators and LP appliances the manufacturer of the accessory has also provided instructions You must read and follow these instructions before using the accessory If you are uncertain whether you have all of the instructions call Walton Trailers at 435 753 5444 before operating the accessory The following accessories are described in this section e Accessory Battery e Electric powered Landing Gear Many accessories introduce the risk of fire and carbon monoxide poisoning If you have an accessory on your trailer make sure you have a fire extinguisher charged and ready before operating the accessory Check the fire extinguisher at least once a month If the fire extinguisher is discharged even partially it must be recharged Follow the fire extinguisher manufacturer s instructions for recharging the extinguisher after use 7 1 ACCESSORY BATTERY Your trailer may be outfitted with an accessory battery that operates lighting electric landing gear dump body slide outs or other accessories An accessory battery may be kept charged either by the tow vehicle or by the generator or shore power A disconnect switch may be provided to disconnect the accessory battery when you do not plan to be using the trailer for a
40. be close to the road surface to drag WARNING Improper rigging of the safety chains can result in loss of control of the trailer and tow vehicle leading to death or serious injury if the trailer uncouples from the tow vehicle e Fasten chains to frame of tow vehicle Do not fasten chains to any part of the hitch unless the hitch has holes or loops specifically for that purpose e Cross chains underneath hitch and coupler with enough slack to permit turning and to hold tongue up if the trailer comes loose 38 Coupling to Tow Information 3 2 2 5 Attach and test electric breakaway brake system If the coupler or hitch fails a properly connected and working breakaway brake system will apply electric brakes on the trailer The safety chains will keep the tow vehicle attached and as the brakes are applied at the trailer s axles the trailer tow vehicle combination will come to a controlled stop The breakaway brake system includes a battery a switch with a pullpin and a lanyard Read and follow the instructions here as well as the instructions that have been prepared by the breakaway brake manufacturer If you do not have these instructions call Walton Trailers at 435 753 5444 for a free copy The breakaway brake system may be fitted with a charging capability that draws power from the tow vehicle If the electrical system on your tow vehicle does not provide power to the breakaway brake battery you must periodica
41. ble for dealer prep which includes checking all cosmetic features and repairing all minor problems without charge to you the end user or the manufacturer Your dealer is also responsible for submitting to the manufacturer any claim you wish to make under the terms of this Limited Warranty This must be completed and then authorized by Walton Trailers with regards to any credit issued in dealing with a structural warranty All other warranty claims regarding components or parts used by Walton Trailers will be directed to the applicable Walton vendors warranty department JURISDICTION AND GOVERNING LAW The laws of the State of Utah hereto shall govern the construction of this warranty and any and all appendixes The Parties hereto confirm that this agreement was formed in Logan Utah and is subject to the jurisdiction of Utah State courts In the event any dispute arises out of this warranty the parties will endeavor to resolve their differences between themselves Upon mutual agreement the parties may engage the services of an Arbitrator However absent a mutual agreement the parties expressly understand that they may seek enforceable relief only in the First Judicial District Court of the State of Utah In the event any action or proceeding is commenced to enforce or interpret any provision of this Agreement the party prevailing in such action or proceeding shall be entitled to recover from the party or parties not prevailing in such action o
42. breakaway pin is pulled The other brake is an electric braking system that acts whenever the brakes of the tow vehicle are applied 8 2 4 3 A BREAKAWAY BRAKE 8 2 4 3 A i BREAKAWAY BATTERY This battery supplies the power to operate the trailer brakes if the trailer uncouples from the tow vehicle Be sure to check maintain and replace the battery according to the battery manufacturer instructions 8 2 4 3 A ii BREAKAWAY SWITCH This switch causes the breakaway battery to operate the electric brakes if the trailer uncouples from the tow vehicle The pull cable for the pull pin is connected to the tow vehicle and the switch is connected to the trailer To check for proper functioning of the switch battery and brakes you must pull the pin from the switch and confirm that the brakes 76 Inspection Service amp Maintenance apply to each wheel You can do this by trying to pull the trailer with the tow vehicle after pulling the pin The trailer brakes may not lock but you will notice that a greater force is needed to pull the trailer A WARNING If electric breakaway brakes do not operate when trailer is uncoupled from the tow vehicle death or serious injury can occur Check emergency breakaway brake system BEFORE each tow 8 2 4 3 B Tow VEHICLE OPERATED ELECTRIC BRAKES The electric brakes that operate in conjunction with the tow vehicle brakes must be synchronized so that braking is properly distributed t
43. conditions exist have the receiver replaced before coupling the trailer Lubricate the inside of the gooseneck ball receiver with automotive bearing grease Be sure the receiver is tight to the trailer All receiver fasteners must be visibly solid against the trailer frame Release the jack handle or crank from its holder see Drop Leg Jack figure Make certain the ground beneath the jack foot is firm enough to support the tongue weight Rotate the handle crank clockwise to raise the bottom surface of the gooseneck to be above the top of the gooseneck ball 3 2 3 1 Prepare the ball receiver and gooseneck ball Release the lock plate on the gooseneck ball receiver With the spring loaded lock plate locking pin in the OPEN position rotate the lock plate to a position that allows the gooseneck ball to enter the receiver see Gooseneck Ball Receiver and Height Adjustment figure Slowly back up the tow vehicle so that the gooseneck ball is aligned under the gooseneck ball receiver 45 Coupling to Tow Information WARNING If the trailer drops during coupling death or serious injury may result There must be no one under the trailer or coupler before or during the coupling operation 3 2 3 2 Couple the trailer to the tow vehicle Rotate the jack handle counter clockwise This will retract the jack causing the gooseneck ball receiver to drop down so it can fully engage the gooseneck ball and transfer the w
44. d Bulk Material Using The Spreader Gate 64 CHECKING THE TRAILER BEFORE AND DURING EACH TOW 68 5 1 PRE TOW GHECKLIST e e ee aee RAD IEEE AEREE UE 68 5 2 MAKE REGULAR STOPS eese enne ntner etnia 68 BREAKING IN A NEW TRAILER esee eene enne 69 6 1 RETIGHTEN LUG NUTS AT FIRST 10 25 amp 50 MILES sese 69 6 2 ADJUST BRAKE SHOES AT FIRST 200 MILES eeeseeeeeeeene 69 6 3 SYNCHRONIZING THE BRAKE SYSTEMS esee 69 ACGESSORIES tee nee ient Se ears 71 Table of Contents 7 1 ACCESSORY BATTERY iecit cede cte cr perm ete nee tiain digin 71 7 2 ELECTRIC POWERED LANDING GEAR cccceseesesssceeceeeeesssnsteeeeeeessssnseeees 71 8 INSPECTION SERVICE amp MAINTENANCE 72 8 1 INSPECTION SERVICE amp MAINTENANCE SUMMARY CHARTS e 72 8 2 INSPECTION AND SERVICE INSTRUCTIONS esee 74 8 2 1 Axle Bolts Frame Suspension amp Structure 74 8 2 2 Trail r Structure d e t i eet eet ett toto te ets 74 8 2 2 4 Fasteners and Frame Members eseeeeeee 74 8 2 222 i MEd a Ducere tere rico 75 8 2 3 Drop Ramp Torsion Springs sse 75 8 2 4 Trailer BraK6S cete iiri tae eer to Fea Fe Eee n ERECTAE 75 8 2 4 1 Brake Shoes and Drums eeeeeeeeeeerernnnnnnnnnnnn 75 8 2 4 2
45. dition if your trailer has a separate braking system the electrical connector will also supply power to the trailer brakes from the tow vehicle Breakaway switch If the trailer becomes de coupled from the towing vehicle the breakaway switch lanyard attached independently to the tow vehicle hitch will pull a pin in the emergency electrical break away switch on the trailer The breakaway switch is activated by a separate battery supply in the trailer such as to energize the trailer brakes independently of the towing vehicle It is important to check the state of charge of the emergency break away battery before each trip Simply pull the pin out of the switch by hand and then try to pull the trailer If you feel a significant drag force the brakes are activated Be sure to re insert the pin in the break away switch Also be sure to allow enough slack in the break away brake lanyard such that the switch will only activate pin pulls out if the coupler connection comes loose For additional details refer to Section 3 2 2 5 Jack A device on the trailer that is used to raise and lower the trailer tongue On larger trailers the jack is sometimes called the landing gear WARNING An improperly coupled trailer can result in death or serious injury Do not move the trailer until e The coupler is secured and locked to hitch e The safety chains are secured to the tow vehicle and e The trailer jack s are fully retracted Do not tow the
46. e allows for easier loading and unloading Pivoting Deck Trailer Tilt Bed 59 Loading the Trailer The pivoting deck trailer is fitted with a spring loaded catch that keeps the trailer in the driving position After the trailer is loaded and the cargo is secured with hold downs be sure the spring loaded catch has locked the trailer into driving position Couple the trailer securely to the tow vehicle before attempting to unlock the deck and load the trailer Unlock the deck and pivot it to the Loading position see Pivoting Deck Trailer figure Before loading the cargo be certain the deck catch pin is retracted A WARNING Loading a pivoting deck trailer before retracting the deck catch pin can crack the catch pin which can cause loss of cargo or loss of control of the trailer Death or serious injury may result Before loading the trailer retract the deck catch pin If the deck catch pin becomes bent do not straighten it Replace the deck catch pin before towing the load Load the cargo onto the trailer with approximately 60 of the cargo in the front half of the bed As the cargo is moved forward on the deck the deck will pivot down into the driving position Extend the deck catch pin into the deck to lock the deck into the driving position see Pivoting Deck Trailer figure Ensure that the catch engages the hole in the pivoting deck A WARNING An unlocked pivoting deck ca
47. e assembly incorporates a wheel supports the tire and attaches either integrally or separably to the wheel center member and upon which the tire is attached Non pneumatic spare tire assembly A non pneumatic tire assembly intended for temporary use in place of one of the pneumatic tires and rims that are fitted to a passenger car in compliance with the requirements of this standard Non pneumatic tire A mechanical device which transmits either directly or through a wheel or wheel center member the vertical load and tractive forces from the roadway to the vehicle generates the tractive forces that provide the directional control of the vehicle and does not rely on the containment of any gas or fluid for providing those functions Non pneumatic tire assembly A non pneumatic tire alone or in combination with a wheel or wheel center member which can be mounted on a vehicle Normal occupant weight This means 68 kilograms 150 lbs times the number of occupants specified in the second column of Table of 49 CFR 571 110 Occupant distribution The distribution of occupants in a vehicle as specified in the third column of Table of 49 CFR 571 110 Tire Safety Information Open splice Any parting at any junction of tread sidewall or innerliner that extends to cord material Outer diameter The overall diameter of an inflated new tire Overall width The linear distance between the exteriors of the sidewalls of a
48. e coupler with a thin layer of automotive bearing grease If your trailer is equipped with a jack raise the coupler above the ball height Open the coupler locking mechanism Ball couplers have a locking mechanism with an internal moving piece ball clamp and an outside handle wheel or latch In the open position the coupler is able to drop fully onto the hitch ball See the coupler instructions for details of placing the coupler in the open position Slowly back up the tow vehicle so that the hitch ball is near or aligned under the coupler if the trailer jack has raised the coupler 36 Coupling to Tow Information 3 2 2 8 Couple the trailer to the tow vehicle If your trailer does not have a jack you will have to lift the coupler and place it over the ball If you have a jack lower the trailer tongue until the coupler fully engages the hitch ball If the coupler does not line up with the hitch ball adjust the position of the tow vehicle Engage the coupler locking mechanism In the engaged position the locking mechanism securely holds the coupler to the hitch ball Insert a pin or lock through the hole in the locking mechanism Be sure the coupler is all the way on the hitch ball and the locking mechanism is engaged A properly engaged locking mechanism will allow the coupler to raise the rear of the tow vehicle Using the trailer jack test to see that you can raise the rear of the tow vehicle by 1 inch after
49. e trailer s use especially after the first 10 25 and 50 miles of driving before each tow and at least twice per year thereafter A WARNING Lug nuts are prone to loosen after initial installation which can lead to death or serious injury Check lug nuts for tightness on a new trailer or when wheel s have been remounted after the first 10 25 and 50 miles of driving A WARNING Metal creep between the wheel rim and lug nuts will cause rim to loosen and could result in a wheel coming off leading to death or serious injury Tighten lug nuts before each tow Tighten the lug nuts to the proper torque for the axle size on your trailer to prevent wheels from coming loose Use a torque wrench to tighten the fasteners The only way to be certain you have checked the torque or torqued the lug nuts to the proper torque is with a torque wrench Four way wrenches ratchets and similar tools can be useful for short term emergency repairs but are not appropriate tools for adequately checking lug nut torque You must use a torque wrench to adequately indicate the torque that you are applying to the lug nut If you do not have a torque wrench tighten the fasteners with a lug wrench as much as you can then have a service garage or dealer tighten the lug nuts to the proper torque Over tightening will result in breaking the studs or permanently deforming the mounting stud holes in the wheels Figure 8 1 Lug nut sequence of tightening 5 L
50. ears for climbing and descending grades Do not ride the brakes while descending grades they may get so hot that they stop working Then you will potentially have a runaway tow vehicle and trailer To conserve fuel don t use full throttle to climb a hill Instead build speed on the approach Slow down for bumps in the road Take your foot off the brake when crossing the bump Do not brake while in a curve unless absolutely necessary Instead slow down before you enter the curve Do not apply the tow vehicle brakes to correct extreme trailer swaying Instead lightly apply the trailer brakes with the hand controller Make regular stops about once each hour Confirm that The coupler is secure to the hitch and is locked Electrical connectors are made There is appropriate slack in the safety chains There is appropriate slack in the breakaway switch pullpin cable The tires are not visibly low on pressure and The cargo is secure and in good condition 15 2 TIRE SAFETY INFORMATION This portion of the User s Manual contains tire safety information as required by 49 CFR 575 6 Section 2 1 contains Steps for Determining Correct Load Limit Trailer Section 2 2 contains Steps for Determining Correct Load Limit Tow Vehicle Section 2 3 contains a Glossary of Tire Terminology including cold inflation pressure maximum inflation pressure recommended inflation pressure and other non technical terms
51. ehicle brakes It will take practice to learn how to back up a tow vehicle with a trailer attached Take it slow Before backing up get out of the tow vehicle and look behind the trailer to make sure that there are no obstacles Some drivers place their hands at the bottom of the steering wheel and while the tow vehicle is in reverse think of the hands as being on the top of the wheel When the hands move to the right counter clockwise as you would do to turn the tow vehicle to the left when moving forward the rear of the trailer moves to the right Conversely rotating the steering wheel clockwise with your hands at the bottom of the wheel will move the rear of the trailer to the left while backing up If you are towing a bumper hitch rig be careful not to allow the trailer to turn too much because it will hit the rear of the tow vehicle To straighten the rig either pull forward or turn the steering wheel in the opposite direction 1 2 18 REPORTING SAFETY DEFECTS If you believe that your vehicle has a defect that could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Walton Trailers If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems bet
52. eight of the trailer tongue to the towing vehicle hitch If the receiver does not line up with the ball raise the receiver again and adjust the position of the tow vehicle Then lower the receiver over the ball When the drop leg base is no longer resting on the ground the towing vehicle hitch is holding all of the weight of the trailer tongue Close the lock plate on the gooseneck ball receiver Move the spring loaded lock plate locking pin to the CLOSED position Be sure the locking pin is holding the lock plate Be sure the receiver is all the way on the gooseneck ball and the lock plate is engaged A properly engaged locking mechanism will allow the coupler to raise the rear of the tow vehicle Using the trailer jack test to see that you can raise the rear of the tow vehicle by 1 inch Overloading can damage the drop leg jack Do not use the drop leg jack to raise the tow vehicle more than 1 inch If the gooseneck ball cannot be secured to the receiver do not tow the trailer Call Walton Trailers at 435 753 5444 or your dealer for assistance After testing to see that the receiver is properly secured and locked to the ball retract the jack to its fully retracted position Return the drop legs to their upper positions The drop legs are held in the lowered position with a plunger pin Rotating the plunger pin while pulling it outward will cause it to come out of engagement with the drop leg and the leg will rapidly rise see
53. ems are not automatically adjusted by hard stopping These brakes require manual adjustment The following steps apply to adjust most manually adjustable brakes Read your axle and brake manual to see how to adjust your brakes If you do not have this manual call Walton Trailers at 435 753 5444 for a free copy e Jack up the trailer and secure it on adequate capacity jack stands e Be sure the wheel and brake drum rotate freely e Remove the adjusting hole cover from the adjusting slot on the bottom of the brake backing plate e With a screwdriver or standard adjusting tool rotate the starwheel of the adjuster assembly to expand the brake shoes Adjust the brake shoes out until the pressure of the linings against the drum makes the wheel very difficult to turn Note Your trailer maybe equipped with drop spindle axles See axle manual for your axle type You will need a modified adjusting tool for adjusting the brakes in these axles With drop spindle axles a modified adjusting tool with about an 80 degree angle should be used e Rotate the starwheel in the opposite direction until the wheel turns freely with a slight drag e Replace the adjusting hole cover e Repeat the above procedure on all brakes e Lower the trailer to the ground 8 2 4 3 Brakes Electric Two different types of electric brakes may be present on the trailer an emergency electric breakaway system which acts only if the trailer comes loose from the hitch and the
54. ending on the exact model This subsection describes loading a rigid deck trailer Before loading a rigid deck trailer couple the trailer to the tow vehicle and make sure the rigid deck is level Do not load or unload the trailer when the deck is not level Make sure the top of the ramp or ramps is secure to the trailer and the bottom is resting on firm ground Pockets may be provided to hold the ramp to the frame of the trailer 58 Loading the Trailer A WARNING Load can suddenly move or topple which can result in death or serious injury Do not load or unload your open trailer unless it is prevented from tipping and is on firm and level ground Load the cargo onto the trailer with approximately 60 of the cargo in the front half of the trailer Secure the cargo to the trailer using appropriate straps chains and tensioning devices Since the trailer ride can be bumpy and rough you must secure your cargo so that it does not shift while the trailer is being towed A WARNING Shifting cargo can result in loss of control of the trailer and can lead to death or serious injury Tie down all loads with proper sized fasteners ropes straps etc Return the ramp s to their stowed position s and secure them so that they will not move during transit 4 3 1 3 Loading a Pivoting deck Tilt Bed Trailer Some open trailers are equipped with a pivoting deck instead of with ramps The pivoting featur
55. eplace as needed Section 8 2 11 Section 8 2 11 1 See Axle Mfr s Manual Section 8 2 10 Structure Axle Attachment Bolts Check BY DEALER Section 8 2 1 73 Inspection Service amp Maintenance 8 2 INSPECTION AND SERVICE INSTRUCTION 8 2 1 AxLE BoLrs FRAME SUSPENSION amp STRUCTURE A WARNING Worn or broken suspension parts can cause loss of control and injury may result Have trailer professionally inspected annually and after any impact To perform many of the inspection and maintenance activities you must jack up the trailer Jacking Points for All Trailers figure indicates the general areas where jacks and jack stands may be applied When jacking and using jack stands place them so as to clear wiring brake lines and suspension parts springs torsion bars etc Place jacks and jack stands inside of the perimeter strip on the supporting structure to which the axles are attached A WARNING Never crawl under your trailer unless it is on firm and level ground and resting on properly placed and secured jack stands 8 2 2 TRAILER STRUCTURE Remove the rubber mats from the floor of the trailer and wash them at least every three months Using a power washer and a detergent solution wash both sides of the rubber mat as well as the floor and walls of the trailer Rinse the rubber mat and the trailer floor and walls Be sure the rubber mat and trailer floor are
56. er leading to death or serious injury Do not load a trailer so that the weight on any tire exceeds its rating Do not exceed the trailer Gross Vehicle Weight Rating GVWR or the Gross Axle Weight Rating GAWR 4 1 TONGUE WEIGHT It is critical to have a portion of the trailer load carried by the tow vehicle That is the trailer tongue must exert a downward force on the hitch This is 53 Loading the Trailer necessary for two reasons First the proper amount of tongue weight is necessary for the tow vehicle to be able to maintain control of the tow vehicle trailer system If for example the tongue exerts an upward pull on the hitch instead of pushing down on it because the trailer is overloaded behind its axle s the rear wheel of the tow vehicle can lose traction or grip and cause loss of control Also even if there is some weight on the tongue but not enough weight on the tongue the trailer can become unstable at high speeds Remember the faster you go the more likely the trailer is to sway If on the other hand there is too much tongue weight the tow vehicle is prone to jack knife like the old Corvairs Furthermore the front wheels of the tow vehicle can be too lightly loaded and cause loss of steering control and traction if the front wheels are driving In addition to tow vehicle control tongue weight is necessary to insure that the trailer axle s do not exceed their Gross Axle Weight Rating GAWR
57. eration Section 6 3 Shoes and Drums Adjust Section 6 2 8 2 4 2 Brakes Hydraulic Vacuum Actuated Check gauge for proper vacuum of 18 In Hg inches of mercury Section 8 2 4 4 A Coupler and Hitch Ball Check for cracks pits and flats Replace w ball amp coupler having trailer GVW Rating Grease Check locking device amp replace Section amp 8 2 5 1 Gooseneck Ball Check for cracks pits and flats Replace w ball amp coupler having trailer GVW Rating Grease Check locking device amp replace when worn Section 3 2 3 1 Section 3 2 3 1 Section amp 8 2 5 2 Safety Chain s amp Check for wear and damage Sections 3 2 2 4 amp Hooks 3 2 3 3 Tires Check tire pressure when cold Inflate Sections 5 1 amp 8 2 9 as needed Wheels Lug Nuts Bolts amp Hub Check for tightness Tighten For new and remounted wheels check torque after first 10 25 amp 50 miles of driving and after any impact Section 5 1 Sections 6 1 amp 8 2 11 2 72 Inspection Service amp Maintenance Inspection and Service each 3 Months or 3 000 Miles Inspection Service Manual Section Item Reference Structure Remove mats Wash both sides Section 8 2 2 gt Rubber mats and floor Wash floor amp 8 2 2 gt Hinges Doors and Inspect Repair or replace dividers damaged worn or broken parts Inspection and
58. erloaded and can be damaged e Release the handle or crank from its holder and engage it with the jack shaft see Drop Leg Jack figure e Rotate the handle or crank from its hold and engage it with the jack shaft see Drop Leg Jack figure e Rotate the handle or crank clockwise to slowly extend the jack and transfer the weight of the trailer tongue to the jack e On two speed jacks pushing the handle shaft toward the gearbox can perform rapid extension This shifts the gearbox into a high speed mode 51 Coupling to Tow Information e When the drop leg base contacts the ground shift the gearbox into low gear mode by pulling or pushing on the handle shaft until it locks into low gear Do not use high gear to lift the trailer the drop leg jack mechanism can be damaged High gear is used only to rapidly move the drop leg base into contact with the ground e Continue to extend the jack s making sure that the ground is providing stable and level support for the trailer e After the jack s are extended and the gooseneck ball receiver is well clear of the gooseneck ball to permit driving the tow vehicle away disengage the handle from its shaft and return to its holder 52 Loading the Trailer 4 LOADING THE TRAILER Improper trailer loading causes many accidents and deaths To safely load a trailer you must consider Overall load weight Load weight distribution Proper tongue weight and Securing
59. es because it is not required by law Letter Rating Speed Rating Q 99 mph R 106 mph S 112 mph FT 118 mph U 124 mph H 130 mph V 149 mph Ww 168 mph Y 186 mph For tires with a maximum speed capability over 149 mph tire manufacturers sometimes use the letters ZR For those with a maximum speed capability over 186 mph tire manufacturers always use the letters ZR U S DOT Tire Identification Number This begins with the letters DOT and indicates that the tire meets all federal standards The next two numbers or letters are the plant code where it was manufactured and the last four numbers represent the week and year the tire was built For example the numbers 3197 means the 31st week of 1997 The other numbers are marketing codes used at the manufacturer s discretion This information is used to contact consumers if a tire defect requires a recall Tire Ply Composition and Materials Used The number of plies indicates the number of layers of rubber coated fabric in the tire In general the greater the number of plies the more weight a tire can support Tire manufacturers also must indicate the materials in the tire which include steel nylon polyester and others Maximum Load Rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire Maximum Permissible Inflation Pressure This number is the greatest amount of air pressure that should ever be put in the tire under normal driving condi
60. g the trailer on the road you must operate the brake controller while trying to pull the trailer in order to confirm that the electric brakes operate While towing the trailer at less than 5 40 Coupling to Tow Information m p h manually operate the electric brake controller in the tow vehicle cab You should feel the operation of the trailer brakes A WARNING Improper electrical connection between the tow vehicle and the trailer will result in inoperable lights and electric brakes and can lead to collision Before each tow e Check that the taillights brake lights and turn signals work e Check that the electric brakes work by operating the brake controller inside the tow vehicle 3 2 2 7 Uncoupling the Ball Hitch Trailer with Tongue Jack Follow these steps to uncouple your ball hitch trailer from the tow vehicle 3 2 3 Block trailer tires to prevent the trailer from rolling before jacking the trailer up Disconnect the electrical connector Disconnect the breakaway brake switch lanyard Disconnect the safety chains from the tow vehicle Unlock the coupler and open it Before extending jack make certain the ground surface below the jack pad will support the tongue load Rotate the jack handle or crank clockwise This will slowly extend the jack and transfer the weight of the trailer tongue to the jack TRAILER WITH GOOSENECK COUPLER AND DROP LEG JACK A gooseneck coupler on the trailer connects
61. han coupler LOAD RATING CHECK that ball SIZE is same as coupler f CLOSE COUPLER CLAMP on ball Pin or padlock 17 LIFT coupler upwards to test that it will not separate from ball wae peck coupler clamp with pin or padlock Lift coupler to check __ 4h Be sure the Ball Hitch coupler is suitable for the size and weight of the trailer The load rating of the coupler and the necessary ball size are listed on the trailer tongue You must provide a hitch and ball for your tow vehicle where the load rating of the hitch and ball is equal to or greater than that of your trailer Also the ball size must be the same as the coupler size If the hitch ball is too small too large is underrated is loose or is worn the trailer can come loose from the tow vehicle and may cause death or serious injury THE TOW VEHICLE HITCH AND BALL MUST HAVE A RATED TOWING CAPACITY EQUAL TO OR GREATER THAN THE TRAILER GROSS VEHICLE WEIGHT RATING GVWR 34 Coupling to Tow Information IT IS ESSENTIAL THAT THE HITCH BALL BE OF THE SAME SIZE AS THE COUPLER The ball size and load rating capacity are marked on the ball hitch capacity is marked on the hitch 3 2 2 1 Before coupling the trailer to the tow vehicle Be sure the size and rating of hitch ball match the size and rating of the coupler Hitch balls and couplers are marked with their size and rating A WARNING Coupler to hitch mismatch can result in uncoupling leading
62. han the corresponding standard tire Tire Safety Information Groove The space between two adjacent tread ribs Innerliner The layer s forming the inside surface of a tubeless tire that contains the inflating medium within the tire Innerliner separation The parting of the innerliner from cord material in the carcass Intended outboard sidewall The sidewall that contains a white wall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle Light truck LT tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles Load rating The maximum load that a tire is rated to carry for a given inflation pressure Maximum load rating The load rating for a tire at the maximum permissible inflation pressure for that tire Maximum permissible inflation pressure The maximum cold inflation pressure to which a tire may be inflated Maximum loaded vehicle weight The sum of curb weight accessory weight vehicle capacity weight and production options weight 19 Measuring rim The rim on which a tire is fitted for physical dimension requirements Non pneumatic rim A mechanical device which when a non pneumatic tir
63. he tire s internal structure starts to breakdown compromising the strength of the tire It is recommended to drive at moderate speeds 80 Inspection Service amp Maintenance Statistics indicate the average life of a trailer tire is about five years under normal use and maintenance conditions After three years replacing the trailer tires with new ones should be considered even if the tires have adequate tread depth Some experts claim that after five years trailer tires are considered worn out and should be replaced even if they have had minimal or no use This is such a general statement that it may not apply in all cases It is best to have your tires inspected by a tire supplier to determine if your tires need to be replaced If you are storing your trailer for an extended period make sure the tires are fully inflated to the maximum rated pressure and that you store them in a cool dry place such as a garage Use tire covers to protect the trailer tires from the harsh effects of the sun A WARNING Worn damaged or under inflated tires can cause loss of control resulting in damage serious injury and possibly death Inspect tires before each tow 8 2 10 WHEEL Rims If the trailer has been struck or impacted on or near the wheels or if the trailer has struck a curb inspect the rims for damage i e being out of round and replace any damaged wheel Inspect the wheels for damage every year even if no obvious i
64. he tow vehicle 46 3 2 3 3 Rig the safety chains s 47 3 2 3 4 Attach and test the breakaway brake system 48 3 2 8 5 Connect the electrical cables sesseessess 50 3 2 3 6 Uncoupling the Gooseneck Trailer with Drop leg Jack 50 LOADING THE TRAILER c ccccsssesscscceseeesnsensseneeseesensensscaees 53 4 1 LONGUE W EIGHT ise niet eret itte c o re p imo Saks ete E 53 4 2 CHECKING TONGUE WEIGHT ccccecceseseeeeeeeeeeeeeeeeeseaeeeeaeeseaeeeeeeessaeeeaees 55 4 3 SECURING THE CARQO 2 ciet ee de cede tee dee oe Yen diesen dn 57 4 3 1 Distributing the Cargo Open Trailer sssssss 57 4 3 1 1 Preparing the Trailer for Loading ssess 58 4 3 1 2 Loading a Rigid deck Trailer 58 4 3 1 8 Loading a Pivoting deck Tilt Bed Trailer 59 4 3 1 4 Preparing the Trailer for Loading ssess 61 4 4 LOADING THE DUMP TRAILER eese 62 4 4 1 Payload Gapacily 2 2 diee ad pe i eie 62 4 4 2 Loading Fixed Loads including equipment such as skid steer loaders 62 4 4 3 Securing the Cargo ee pees Ee ri b mdp eee 62 4 4 4 Unloading Flowable Loads from the Dump Trailer 63 4 4 5 Hydraulic Components esses 63 4 4 6 Body Prop tere tre ay deter 64 4 4 7 Unloa
65. hers can die or be seriously injured Load in trailer must not exceed 8250 Ibs It must be evenly distributed 4 4 2 LOADING FIXED LOADS INCLUDING EQUIPMENT SUCH AS SKID STEER LOADERS e Fixed loads that are to be carried or dumped should be loaded evenly throughout the trailer Too much load in the front portion will strain and possibly overload the hydraulic hoist Too much load in the rear will lead to reduced trailer sway stability at highway speeds Inspect the hold down openings or D rings for any cracks or kinks Clear the area around the dump trailer Load the equipment or material Secure the equipment Close and fasten doors If loading ramps are used the operator must be experienced and skilled to perform the loading 4 4 3 SECURING THE CARGO Since the trailer cargo is subjected to longitudinal front back and lateral side side forces you must secure all cargo that is not flowable so that it does not shift while the trailer is being towed 62 4 4 4 Loading the Trailer UNLOADING FLOWABLE LOADS FROM THE DUMP TRAILER Read and understand the hoist operating procedure before dumping the load Be sure the trailer is on level ground both left right and front back Attempting to unload on uneven ground may cause the trailer to overturn which can result in serious injury or death Clear the area around the dump trailer Open the rear doors and make sure they are securely hooked to the s
66. ials in your trailer Exceptions Fuel in the tanks of vehicles that are being towed Fuel stored in proper containers used in trailer living quarters for cooking Fuel stored in the tank of an on board generator 4 3 1 4 Preparing the Trailer for Loading Before loading cargo into your enclosed trailer inspect the interior of the trailer Enclosed trailers may be fitted with D ring hold downs and or a track system that can be used to secure the cargo Inspect the D rings and track system for looseness or signs of bending before loading the cargo onto the trailer 61 Loading the Trailer WARNING Damaged or loose D rings can break allowing cargo to become loose inside the trailer Loose cargo can shift the center of gravity and result in loss of control of the trailer Inspect D rings and test them for looseness before loading cargo Do not use a damaged or loose D ring to secure cargo 4 4 LOADING THE DUMP TRAILER 4 4 1 PAYLOAD CAPACITY Check if the trailer has payload decals on the sides If not then determine the payload or Cargo Capacity by subtracting the empty weight of the trailer from the GVWR given on the Certification VIN tag Determine the density of the material to be loaded and dumped so that you will know approximately how many cubic yards of material may be safely loaded carried and dumped A WARNING Trailer hitch or dump body can fail You or ot
67. ides of the trailer using the hold back door chains Undo the latch on the control box and open the cover exposing the control switch The control box cover should be locked when the dump trailer is not being used Standing well clear of the dump bed push the UP button on the control device until the dump bed reaches approximately the halfway point of its dumping angle Never leave the control device when operating the dump bed Discontinue pushing the UP button and walk to the rear of the trailer SO you can estimate if there is enough space for the remainder of the load to be safely dumped If not then you need to lower the dump bed by depressing the DOWN button and pull the trailer forward and then repeat the previous step Standing well clear of the dump bed raise the dump bed to the three quarter point of the maximum dump angle Stop the lift and walk to the rear to check to see if there is enough space for continued dumping Repeat the process until the load has been completely dumped If the load has not completely dumped DO NOT drive forward and stop quickly to shock the load out of the bed Also DO NOT jerk the control button up and down to dislodge the load The proper procedure for a stuck load is to lower the dump and dislodge the material by hand Secure the rear doors prior to moving forward Risk of Death by crushing Empty dump body before using body prop 4 4 5 HYDRAULIC COMPONENTS Do not alte
68. ifferent feel and maneuverability of the tow vehicle with a loaded trailer Because of the significant differences in all aspects of maneuverability when towing a trailer the hazards and risks of injury are also much greater than when driving without a trailer You are responsible for keeping your vehicle and trailer in control and for all the damage that is caused if you lose control of your vehicle and trailer As you did when learning to drive an automobile find an open area with little or no traffic for your first practice trailering Of course before you start towing the trailer you must follow all of the instructions for inspection testing loading and coupling Also before you start towing adjust the mirrors so you can see the trailer as well as the area to the rear of it Drive slowly at first 5 mph or so and turn the wheel to get the feel of how the tow vehicle and trailer combination responds Next make some right and left hand turns Watch in your side mirrors to see how the trailer follows the tow vehicle Turning with a trailer attached requires more room 13 General Safety Information Stop the rig a few times from speeds no greater than 10 mph If your trailer is equipped with brakes try using different combinations of trailer electric brake and tow vehicle brake Note the effect that the trailer brakes have when they are the only brakes used When properly adjusted the trailer brakes will come on just before the tow v
69. ill read below it is difficult to obtain the recommended tire pressure if your tires are not cold Because tires are designed to be used on more than one type of vehicle tire manufacturers list the maximum permissible inflation pressure on the tire sidewall This number is the greatest amount of air pressure that should ever be put in the tire under normal driving conditions 2 4 4 CHECKING TIRE PRESSURE It is important to check your vehicle s tire pressure at least once a month for the following reasons e Most tires may naturally lose air over time e Tires can lose air suddenly if you drive over a pothole or other object or if you strike the curb when parking e With radial tires it is usually not possible to determine underinflation by visual inspection For convenience purchase a tire pressure gauge to keep in your vehicle Gauges can be purchased at tire dealerships auto supply stores and other retail outlets The recommended tire inflation pressure that vehicle manufacturers provide reflects the proper psi when a tire is cold The term cold does not relate to the outside temperature Rather a cold tire is one that has not been driven on for at least three hours When you drive your tires get warmer causing the air pressure within them to increase Therefore to get an accurate tire pressure reading you must measure tire pressure when the tires are cold or compensate for the extra pressure in warm tires 2 4 5 STEPS F
70. ill tend to straighten out the combination especially when going downhill e Check rearview mirrors frequently to observe the trailer and traffic e Use lower gear when driving down steep or long grades Use the engine and transmission as a brake Do not ride the brakes as they can overheat and become ineffective e Be aware of your trailer height especially when approaching bridges roofed areas and around trees 1 2 4 TRAILER NoT PROPERLY COUPLED TO THE HITCH It is critical that the trailer be securely coupled to the hitch ball and that the safety chains and emergency break away brake cable are correctly attached Uncoupling may result in death or serious injury to you and to others A WARNING Proper selection and condition of the coupler and hitch are essential to safely towing your trailer A loss of coupling may result in death or serious injury e Be sure the maximum load rating of the hitch on the tow vehicle is equal to or greater than the maximum load rating of the coupler on the trailer e Be sure the hitch ball size matches the coupler size e Observe the hitch for wear corrosion and cracks before coupling Replace worn corroded or cracked hitch components before coupling the trailer to the tow vehicle e Besurethe hitch components are tight before coupling the trailer to the tow vehicle General Safety Information A WARNING An improperly coupled trailer can result in death or serious injury Do not
71. inflation levels Cold means that the tires are at the same temperature as the surrounding air such as when the vehicle has been parked overnight Wheel and tire manufacturers recommend adjusting the air pressure to the trailer manufacturer s recommended cold inflation pressure in pounds per square inch PSI stated on the vehicle s Federal Certification Label or Tire Placard when the trailer is loaded to its gross vehicle weight rating GVWR If the tires are inflated to less than the recommended inflation level or the GVWR of the trailer is exceeded the load carrying capacity of the tire could be dramatically affected If the tires are inflated more than the recommended inflation level handling characteristics of the tow vehicle trailer combination could be affected Refer to the owner s manual or talk to your dealer or vehicle manufacturer if you have any questions regarding proper inflation practices Tires can lose air over a period of time In fact tires can lose 1 to 3 PSI per month This is because molecules of air under pressure weave their way from the inside of the tire through the rubber to the outside A drop in tire pressure could cause the tire to become overloaded leading to excessive heat build up If a trailer tire is under inflated even for a short period of time the tire could suffer internal damage High speed towing in hot conditions degrades trailer tires significantly As heat builds up during driving t
72. ing battery must be in good condition and properly rigged to be effective General Safety Information A WARNING An ineffective or inoperative breakaway brake system can result in a runaway trailer leading to death or serious injury if the coupler or hitch fails The breakaway cable must be connected to the tow vehicle and NOT to any part of the hitch Before towing the trailer test the function of the breakaway brake System If the breakaway brake system is not working do not tow the trailer have it serviced or repaired 1 2 7 MATCHING TRAILER AND HITCH Use of a hitch with a load rating less than the load rating of the trailer can result in loss of control and may lead to death or serious injury 1 2 8 Worn TIRES LOOSE WHEELS AND LUG NUTS Just as with your tow vehicle the trailer tires and wheels are important safety items Therefore it is essential to inspect the trailer tires before each tow If a tire has a bald spot bulge cut cracks or is showing any cords replace the tire before towing If a tire has uneven tread wear take the trailer to a dealer service center for diagnosis Uneven tread wear can be caused by tire imbalance axle misalignment or incorrect inflation Tires with too little tread will not provide adequate frictional forces on wet roadways and can result in loss of control leading to death or serious injury Improper tire pressure causes increased tire wear and may reduce trailer stabilit
73. ing proper tire pressure Not keeping lug nuts tight 1 2 1 IMPROPER SIZING OF THE TRAILER TQ THE TOW VEHICLE Trailers that weigh too much for the towing vehicle can cause stability problems which can lead to death or serious injury Furthermore the additional strain put on the engine and drive train may lead to serious tow vehicle maintenance problems For these reasons the maximum towing capacity of your towing 2 General Safety Information vehicle should not be exceeded The towing capacity of your tow vehicle in terms of maximum Gross Trailer Weight GTW and maximum Gross Combined Weight Rating GCWR can be found in the tow vehicles Owner s Manual Use of a tow vehicle with a towing capacity less than the Gross Vehicle Weight Rating of the trailer can result in loss of control and may lead to death or serious injury Be sure your hitch and tow vehicle are rated for the Gross Vehicle Weight Rating of your trailer 1 2 2 DRiviNG Too FAST With ideal road conditions the maximum recommended speed for safely towing a trailer is 60 mph If you drive too fast the trailer is more likely to sway thus increasing the possibility for loss of control Also your tires may overheat thus increasing the possibility of a blowout A WARNING Driving too fast for conditions can result in loss of control and cause death or serious injury Decrease your speed when going downhill or as road weather and lighting conditions de
74. instructions below may vary slightly from the jack manufacturer s instructions If the trailer jack on your trailer does not resemble the jack shown in the figures follow the jack instructions provided by the jack manufacturer If you do not have these instructions call Walton Trailers at 435 753 5444 for a free copy Drop leg Jack Arrangement Before attempting to tow the trailer Be sure the size and rating of the gooseneck ball match the size and rating of the receiver Gooseneck balls and receivers are marked with their size and ratings Wipe the gooseneck ball clean and inspect it visually and by feel for flat Spots cracks and pits 44 Coupling to Tow Information A WARNING A worn cracked or corroded gooseneck ball can fail while towing and may result in death or serious injury Before coupling the trailer inspect the gooseneck ball for wear corrosion and cracks and replace worn or damaged gooseneck ball Rock the ball to make sure it is tight to the ball support and visually check that the gooseneck ball nut is solid against the lock washer and ball support frame A WARNING A loose gooseneck ball can result in uncoupling leading to death or serious injury Be sure the gooseneck ball nut is tight before coupling the trailer Wipe the inside and outside of the receiver clean and inspect it visually for cracks and feel the inside of the receiver for worn spots and pits If any of these
75. is essential in the operation of the electric brakes on the trailer If your trailer has electric brakes it requires a brake controller be installed at the driver s position The brake controller is not the same as the safety breakaway brake system that is installed on the trailer Side View Mirrors The size of the trailer that is being towed and your state law regulations determine the size of the mirrors However some states prohibit extended mirrors on a tow vehicle except while a trailer is actually being towed In this situation detachable extended mirrors are necessary Check with your dealer or the appropriate state agency for mirror requirements Heavy Duty Flasher A Heavy Duty Flasher is an electrical component that may be required when your trailer turn signal lights are attached to the tow vehicle flasher circuit Electrical Connector An Electrical Connector connects the light and brake Systems on the trailer to the light and brake controls on the towing vehicle Heavy Duty Engine Oil Cooling System The tow vehicle engine works harder when a trailer is being towed Depending on the size of the trailer you may need to install a separate engine oil cooler Inadequate cooling may result in sudden engine failure Ask the tow vehicle dealer if it is necessary to install a heavy duty cooling system 31 Coupling to Tow Information e Automatic Transmission Oil Cooler The automatic transmission of a towing vehicle handles more
76. ll loads with proper sized fasteners ropes straps etc If the door latch is equipped with a catch that has a hole for a linchpin use a linchpin to prevent the door latch from opening General Safety Information A WARNING If the door opens your cargo may be ejected onto the road resulting in death or serious injury to other drivers Always secure the door latch after closing Place a linchpin in the catch 1 2 12 INAPPROPRIATE CARGO Your trailer may be designed for specific cargo for example only for horses If your trailer is designed for specific cargo only carry that cargo in the trailer A utility trailer must not be used to carry certain items such as people containers of hazardous substances or containers of flammable substances WARNING Do not transport people inside the trailer even if it has living quarters The transport of people puts their lives at risk and may be illegal A WARNING Do not transport flammable explosive poisonous or other dangerous materials in your trailer Exceptions e Fuel in the tanks of vehicles that are being towed e Fuel stored in proper containers used in trailer living quarters for cooking e Fuel stored in the tank of an on board generator 1 2 13 INOPERABLE BRAKES LIGHTS OR MIRRORS Be sure that the electric brakes and all of the lights on your trailer are functioning properly before towing your trailer Electric brakes and lights on a trailer are con
77. lly charge the battery to keep the breakaway brake system in working order Breakaway Brake Bumper Pull Trailer PIN PULLED OUT ONLY TO TEST BRAKES Trailer can roll if it comes loose Electric safety brake applies when cable pulls pin out of switch box 1 PULL hard to get pin out of switch box 2 CHECK brake by PULLING TRAILER with tow vehicle 3 ATTACH pin CABLE to tow vehicle so ATTACH pin will be pulled out if trailer separates LEN IN 4 Promptly REPLACE pin in switch box VEHICLE TOWING AND 2002 NATM STORAGE UT0014 Connect the pullpin lanyard to the tow vehicle so that the pullpin will be pulled out before all of the slack in the safety chains is taken up see Breakaway Brake System figure Do not connect the pullpin cable to a safety chain or to the hitch ball or hitch ball assembly This would keep the breakaway brake system from operating when it is needed To test the break away brake battery remove the pullpin from the switch and attempt to pull the trailer forward You should feel the trailer resisting being towed but the wheels will not necessarily be locked If the brakes do not function do not tow the trailer until brakes or battery are repaired Immediately replace the pullpin The breakaway brake system battery discharges rapidly when the pullpin is removed 39 Coupling to Tow Information A WARNING An ineffective breakaway brake system can result in a runaway trailer
78. locking device that secures the coupler to the ball for proper operation See the coupler manufacturer s manual for other inspection and maintenance activities If you do not have this manual call Walton Trailers at 435 753 5444 for a free copy If you see or feel evidence of wear such as flat spots deformations pitting or corrosion on the ball or coupler immediately have your dealer inspect them to determine the proper action to prevent possible failure of the ball and coupler system All bent or broken coupler parts must be replaced before towing the trailer The coupler handle lever must be able to rotate freely and automatically snap into the latched position Oil the pivot points sliding surfaces and spring ends with SAE 30W motor oil Keep the ball pocket and latch mechanism clean Dirt or contamination can prevent proper operation of the latching mechanism 78 Inspection Service amp Maintenance When replacing a ball the load rating must match or exceed the GVWR of the trailer 8 2 5 2 Gooseneck The gooseneck receiver on the trailer connects to a hitch mounted ball on the towing vehicle The receiver ball and hitch transfer the towing forces between the tow vehicle and the trailer Before each tow coat the ball with a thin layer of automotive bearing grease to reduce wear and ensure proper operation and check the locking device that secures the receiver to the ball for proper operation See the gooseneck ball
79. ment figure e Rotate the lock plate to a position that permits the gooseneck ball to exit the receiver 50 Coupling to Tow Information Before releasing dropleg jack make certain ground surface below jack base will support the trailer tongue load e Rotate the drop leg plunger pin handle so that the plunger pin is released from the drop leg see Releasing Drop Leg Mechanism figure e Push down on the drop leg base with your foot to place a drop leg to the desired lowered position e Rotate the plunger pin handle so that the plunger pin is attempting to engage the drop leg see Releasing Drop Leg Mechanism figure e Slowly raise your foot permitting the drop leg to raise The plunger pin will engage a hole in the drop leg The drop legs are heavily spring loaded in the lowered position They will rapidly return to the upper position when released and can inflict serious bruises scrapes or pinching Keep your feet shins and hands well clear of the drop legs and drop leg bases when releasing the drop legs Always wear shoes or boots while performing this operation e Be sure the plunger pin is fully engaged Push it in by hand if necessary The bent part of the plunger pin handle must be touching the plunger pin housing e If your trailer has two drop leg jacks lower them both to the same level following the above instructions If the drop legs are not set at the same level one of the drop leg jacks can be ov
80. move the trailer until e The coupler is secured and locked to hitch ball e The safety chains are secured to the tow vehicle and e The trailer jack s are fully retracted Do not tow the trailer on the road until Tires and wheels are checked The trailer brakes are checked The breakaway switch is connected to the tow vehicle The load is secured to the trailer and The trailer lights are connected and checked 1 2 5 Proper USE OF SAFETY CHAINS If your trailer comes loose from the hitch for any reason we have provided safety chains so that control of the trailer can still be maintained A WARNING Improper rigging of the safety chains can result in loss of control of the trailer and tow vehicle leading to death or serious injury if the trailer uncouples from the tow vehicle e Fasten chains to frame of tow vehicle Do not fasten chains to any part of the hitch unless the hitch has holes or loops specifically for that purpose e Cross chains underneath hitch and coupler with enough slack to permit turning and to hold tongue up if the trailer comes loose 1 2 6 PROPER CONNECTION OF BREAKAWAY BRAKE If equipped with brakes your trailer will be equipped with a breakaway brake System that can apply the brakes on your trailer if your trailer comes loose from the hitch ball for any reason You will have a separate set of instructions for the breakaway brake if your trailer is so equipped The breakaway brake system includ
81. mpact has occurred 8 2 11 WHEELS BEARINGS AND LUG NuTS A loose worn or damaged wheel bearing is the most common cause of brakes that grab To check your bearings jack trailer and check wheels for side to side looseness If the wheels are loose or spin with a wobble the bearings must be serviced or replaced Most trailer axles are built with sealed bearings that are not serviceable Sealed bearings must be replaced as complete units 8 2 11 1 Unsealed Bearings Hubs If your trailer has unsealed axle bearings they must be inspected and lubricated once a year or 12 000 miles to insure safe operation of your trailer If a trailer wheel bearing is immersed in water it must be replaced If your trailer has not been used for an extended amount of time have the bearings inspected and packed more frequently at least every six months and prior to use 81 Inspection Service amp Maintenance Exploded view of Wheel Bearing or SF Hub amp Drum Assembly Hub Assembly 90 0 Required with AG Spindle Follow the steps below to disassemble and service the UNSEALED wheel bearings e After removing the grease cap cotter pin spindle nut and spindle washer items 7 10 in Exploded Wheel Bearing figure remove the hub and drum to inspect the bearings for wear and damage e Replace bearings that have flat spots on rollers broken roller cages rust or pitting Always replace bearings and cups in sets The
82. n extended period such as seasonal storage If there is no disconnect switch then remove the cables from the battery terminals The accessory battery must be kept in a charged condition during storage The battery could freeze and break if it becomes discharged 7 2 ELECTRIC POWERED LANDIN EAR The landing gear also known as the jack on your trailer may be powered with an electric motor The landing gear is operated up or down using controls located near the landing gear If the motor does not operate such as when the battery is fully discharged the landing gear can be operated manually with a socket wrench 71 Inspection Service amp Maintenance 8 INSPECTION SERVICE amp MAINTENANCE 8 1 INSPECTION SERVICE amp MAINTENANCE SUMMARY CHARTS You must inspect maintain and service your trailer regularly to insure safe and reliable operation If you cannot or are unsure how to perform the items listed here have your dealer do them Note In addition to this manual also check the relevant component manufacturer s manual Inspection and Service before Each Use Item Inspection Service Manual Section Reference Breakaway Brakes Electric Hydraulic Check operation Check fluid level Sections 3 2 2 5 3 2 3 4 Section 8 2 4 4 Breakaway Battery Fully charged connections clean Sections 3 2 2 5 3 2 3 4 amp Section 8 2 4 3 A i Brakes all types Check op
83. n inflated tire including elevations due to labeling decorations or protective bands or ribs Ply A layer of rubber coated parallel cords Ply separation A parting of rubber compound between adjacent plies Pneumatic tire A mechanical device made of rubber chemicals fabric and steel or other materials that when mounted on an automotive wheel provides the traction and contains the gas or fluid that sustains the load Production options weight The combined weight of those installed regular production options weighing over 2 3 kilograms 5 lbs in excess of those standard items which they replace not previously considered in curb weight or accessory weight including heavy duty brakes ride levelers roof rack heavy duty battery and special trim Radial ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread Recommended inflation pressure This is the inflation pressure provided by the vehicle manufacturer on the Tire Information label and on the Certification VIN tag 20 Reinforced tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire Rim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated Rim diameter This means the nominal diameter of the bead seat Rim size designation This means the rim diameter and width
84. n result in loss or cargo or loss of control of the trailer which can result in death or serious injury Before towing the trailer e Lock the pivoting deck in the driving position e Double check that the catch engages the hole in the pivoting deck Secure the cargo onto the trailer using appropriate straps and tensioning devices Since the trailer ride can be bumpy and rough you must secure your cargo so that it does not shift while the trailer is being towed 60 Loading the Trailer A WARNING Shifting cargo can result in loss of control of the trailer and can lead to death or serious injury Tie down all loads with proper sized fasteners ropes straps etc Loading Cargo Enclosed Trailer Couple the trailer to the tow vehicle before loading The tongue of a bumper pull trailer can rise during loading before the cargo is properly distributed To measure the tongue weight you will have to uncouple the trailer after it is loaded Do not transport people containers of hazardous substances cans or containers of flammable substances However fuel in the tank of an off road vehicle or a car or motorcycle etc may be carried inside of your enclosed cargo trailer A WARNING Do not transport people inside the trailer even if it has living quarters The transport of people puts their lives at risk and may be illegal A WARNING Do not transport flammable explosive poisonous or other dangerous mater
85. n tow vehicle brake pedal Turn Signals Operate tow vehicle directional signal lever Check electric brakes for proper operation If your trailer has electric brakes your tow vehicle will have an electric brake controller that sends power to the trailer brakes Before towing the trailer on the road you must operate the brake controller while trying to pull the trailer in order to confirm that the electric brakes operate While towing the trailer at less than 5 m p h manually operate the electric brake controller in the tow vehicle cab You should feel the operation of the trailer brakes A WARNING Improper electrical connection between the tow vehicle and the trailer will result in inoperable lights and electric brakes and can lead to collision Before each tow e Check that the taillights brake lights and turn signals work e Check that the electric brakes work by operating the brake controller inside the tow vehicle 3 2 3 6 Uncoupling the Gooseneck Trailer with Drop leg Jack Follow these steps to uncouple your gooseneck hitch trailer from the tow vehicle e Block trailer tires to prevent the trailer from rolling before jacking the trailer up Disconnect the electrical connector Disconnect the breakaway brake switch lanyard Disconnect the safety chains from the tow vehicle Move the spring loaded gooseneck receiver lock plate locking pin to the OPEN position see Gooseneck Ball Receiver and Height Adjust
86. n trailer If this signed warranty is not postmarked faxed by the tenth 10 calendar day after the purchase of the trailer all express warranties shall be null and void 2 If any problems arise with your Walton trailer return your trailer to the dealer for inspection Dealers are responsible for fixing any minor problems without charge to you or the factory WARNING DO NOT attempt to use or move your trailer if it is in an unsafe operating condition or if moving it could cause injury or harm to anyone or cause further damage to the trailer 3 If your dealer cannot repair the problem free of charge and you want to make a claim under this warranty your local dealer must contact Walton Trailers in regards to filing a claim The dealer will work with the factory in determining if a warranty claim approval will be issued and whether the repair can be fixed at the dealer s location or another facility 4 The dealer must contact the warranty department of Walton Trailers and make a warranty claim The defect in workmanship or material must be fully documented signed dated and then sent with pictures to Walton Trailers to be reviewed for a warranty approval 5 Walton Trailers will Not credit any dealer for any adjustment or repair of a Walton trailer without prior written claim approval from the warranty department 6 Walton Trailers reserves the right to establish reasonable reimbursement amounts for any authorized work performed under the
87. nded to serve as hitches e Weight Distributing Hitch or Equalizing Hitch A mechanical device that connects the trailer to the towing vehicle and by means of leverage applied on both the trailer and towing vehicle structures when properly adjusted distributes the imposed vertical load at the hitch and coupling connection between structures of the towing vehicle and trailer e Weight Carrying Hitch A mechanical and or structural device that connects the trailer to the towing vehicle and that does not employ features designed to redistruibute the load imposed at the hitch and carrying connection Safety chains or cables Chains or cables permanently attached to the trailer such that if the coupler connection comes loose the safety chains or cables can keep the trailer attached to the tow vehicle With properly rigged safety chains or cables it is possible to keep the tongue of the trailer from digging into the road pavement even if the coupler to hitch connection comes apart 32 Coupling to Tow Information Some states do not allow safety cables e g Pennsylvania therefore it may be wise to check with the State Police to see if your state has any restrictions on the use of safety cables if your trailer is so equipped Trailer lighting and braking connector A device that connects electrical power from the tow vehicle to the trailer Electricity is used to turn on brake lights running lights and turn signals as required In ad
88. necessarily lock up Immediately replace the pullpin The breakaway brake system battery discharges rapidly when the pullpin is removed A WARNING An ineffective or inoperative breakaway brake system can result in a runaway trailer leading to death or serious injury if the coupler or hitch fails Connect the breakaway cable to the tow vehicle and NOT to the safety chain safety chain receiver gooseneck ball or gooseneck ball support Test the function of the breakaway brake system before towing the trailer Do not tow the trailer if the breakaway brake system is not working have it serviced or repaired Do not tow the trailer with the breakaway brake system ON because the brakes will overheat which can result in permanent brake failure A WARNING Failure to replace the pullpin will prevent brakes from working leading to loss of control serious injury or death If you do not use your trailer for three or more months or during winter months Store the battery indoors and Charge the battery every three months 49 Coupling to Tow Information Replace the breakaway brake battery at intervals recommended by the battery manufacturer s instructions 3 2 3 5 Connect the electrical cables Connect the trailer lights to the tow vehicle s electrical system using the electrical connectors Check all lights for proper operation Clearance and Running Lights Turn on tow vehicle headlights Brake Lights Step o
89. ns or containers of flammable substances such as gasoline kerosene paint etc However fuel in the tank of an off road vehicle or a car or motorcycle etc may be carried on your open trailer 57 Loading the Trailer A WARNING Do not transport flammable explosive poisonous or other dangerous materials in your trailer Exceptions Fuel in the tanks of vehicles that are being towed Fuel stored in proper containers used in trailer living quarters for cooking Fuel stored in the tank of an on board generator 4 3 1 1 Preparing the Trailer for Loading Before loading cargo onto the trailer e Inspect the deck of the trailer for corrosion or damage and e Inspect the hold down openings and or D rings Hold down openings must be sturdy with no visible cracks or kinks D rings must be tight to the deck and must not be bent If the deck or any required hold down is damaged do not load the cargo Bring the trailer to your dealer or a competent repair service before using it to carry cargo A WARNING Damaged or loose D rings can break allowing cargo to become loose inside the trailer Loose cargo can shift the center of gravity and result in loss of control of the trailer Inspect D rings and test them for looseness before loading cargo Do not use a damaged or loose D ring to secure cargo 4 3 1 2 Loading a Rigid deck Trailer Open trailers have either a rigid deck or a pivoting deck dep
90. nside the cab of the tow vehicle must indicate 18 In Hg inches of mercury or more at all times 77 Inspection Service amp Maintenance WARNING If the vacuum gauge in tow vehicle is not at or above 18 In Hg inches of mercury damage to the brake system will result and the brakes may become inoperable 8 2 4 4 B AiR PRESSURE OPERATED HYDRAULIC Air hydraulic braking systems are typically used when the tow vehicle has a diesel engine The tow vehicle has an air compressor that routes the air to an air hydraulic mechanism which sends brake fluid to the wheel cylinders The air pressure gauge in your tow vehicle indicates the current air pressure See your tow vehicle manual for the proper air pressure 8 2 4 4 C ELECTRICAL OPERATED HYDRAULIC Electric hydraulic braking systems which are mounted on the trailer use a small electrically driven pump to generate hydraulic pressure which operates the brake cylinders Like electrical brakes an electric hydraulic braking system is operated by an electrical signal from the tow vehicle 8 2 5 TRAILER CONNECTION TO TOW VEHICLE 8 2 5 1 Coupler and Ball The coupler on the trailer connects to the ball attached to the hitch on the tow vehicle The coupler ball and hitch transfer the towing forces between the tow vehicle and the trailer Before each tow coat the ball with a thin layer of automotive bearing grease to reduce wear and ensure proper operation and check the
91. o the tow vehicle brakes and the trailer brakes For proper operation and synchronization read and follow the axle brake and the brake controller manufacturers instructions If you do not have these instructions call Walton Trailers at 435 753 5444 for a free copy 8 2 4 3 C MAGNETS FOR ALL ELECTRIC BRAKES To make certain an electrically operated braking system will function properly you must have your dealer inspect the magnets at least once a year or each 12 000 miles See the brake manual for wear and current inspection instructions 8 2 4 4 Brakes Hydraulic vacuum air or electric operated If your trailer has hydraulically operated brakes they function the same way the hydraulic brakes do on your tow vehicle The hydraulic braking system must be inspected by a dealer at least as often as the brakes on the tow vehicle but no less than once per year This inspection includes an assessment of the condition and proper operation of the wheel cylinders brake shoes brake drums and hubs You must check the fluid level in the master cylinder reservoir at least every three months If you tow your trailer an average of 1 000 miles per month in a hot and dry environment you must check the brake fluid level once a month The brake fluid reservoir is located on the tongue of the trailer or near the gooseneck Fill with DOT 4 brake fluid 8 2 4 4 A VACUUM OPERATED HYDRAULIC When towing a trailer the vacuum gauge which is located i
92. of electrocution Dump body coming near or contacting power lines may result in electrocution Electrocution can occur without contact Be sure there are no overhead power lines over or near the trailer before raising dump body A lowering or falling dump body can result in death or serious injury NEVER enter the area under the dump body unless the empty dump body is supported by the body props The body props are designed to support an empty dump body only NEVER support a loaded dump body by the body props Unload the dump body before using body props Press and hold button to raise the dump body Release the button when the body has reached approximately the halfway point of its dumping angle or if the load begins to shift rearward Never leave the dump body control when operating the dump body A WARNING Fully raising the loaded dump body may result in the tow vehicle rear wheels loosing traction Do not fully raise a loaded dump body or place the entire load at the rear of trailer Watch for and avoid obstructions such as tree limbs overhead lines potholes etc and SLOWLY drive the tow vehicle and trailer ahead to spread the material DO NOT drive forward and stop quickly to shock the load out of the body DO NOT jerk the control button up and down to 66 Loading the Trailer dislodge the load The proper procedure for a stuck load is to fully lower the dump and dislodge the material by hand Y
93. ormation Tongue Weight as a Percentage of Loaded Trailer Weight Type of Hitch 10 15 for large trailers Ball Hitch or Bumper Hitch 6 10 for smaller utility and cargo trailers 4 6 for boat trailers Gooseneck Hitch 20 25 Fifth Wheel Hitch 20 25 The numbers quoted above are for example purposes only and should be tailored to the specific trailer For questions regarding the actual percent of tongue weight for the trailer check with the manufacturer for specifics Uneven left right load distribution can cause tire wheel axle or structural failure Be sure your trailer is evenly loaded left right Towing stability also depends on keeping the center of gravity as low as possible WARNING Improper tongue weight load distribution can result in loss of control of the trailer leading to death or serious injury Make certain that tongue weight is within the allowable range Be sure to Distribute the load front to rear to provide proper tongue weight see chart For dump trailers a flowable load should be evenly distributed throughout the bed Distribute the load evenly right and left Keep the center of gravity low 1 2 11 HIFTING AR Since the trailer ride can be bumpy and rough you must secure your cargo so that it does not shift while the trailer is being towed A WARNING Shifting cargo can result in loss of control of the trailer and can lead to death or serious injury Tie down a
94. ou may need to raise the dump body higher after a portion of the load has been spread to place the remaining material at the rear of the dump body Stop tow vehicle after all material has exited the dump body Press and hold button to lower the dump body Release button when the dump body is fully lowered Close and latch rear gate 67 Checking the Trailer Before amp During Each Tow 5 CHECKING THE TRAILER BEFORE AND DURING EACH Tow 5 1 PRE TOW CHECKLIST Before towing double check all of these items See section 8 1 Inspection Service amp Maintenance Summary Charts for more information e Tires wheels and lug nuts see the Major Hazards section starting on page 2 of this manual e Tire Pressure Inflate tire on trailer and tow vehicle to the pressure stated on the VIN Certification label e Coupler secured and locked see the Coupling and Uncoupling the Trailer section starting on page 32 of this manual e Safety chains properly rigged to tow vehicle not to hitch or ball see the Coupling to the Tow Vehicle chapter starting at Page 29 of this manual e Testoflights Tail Stop and Turn Lights e Testtrailer brakes e Safety breakaway switch cable fastened to tow vehicle not to safety chains see the Coupling to the Tow Vehicle chapter starting at Page 29 of this manual e Cargo properly loaded balanced and tied down see the Loading the Trailer chapter starting at page 53 of this manual
95. power when a trailer is being towed Inadequate cooling will shorten transmission life and may result in sudden transmission failure Ask the tow vehicle dealer if it is necessary to install a separate oil cooler for the automatic transmission e Fire Extinguisher It is sensible to have a fire extinguisher in the tow vehicle e Emergency Flares and Emergency Triangle Reflectors It is wise to carry these warning devices even if you are not towing a trailer It is particularly important to have these when towing a trailer because the hazard flashers of your towing vehicle will not operate for as long a period of time when the battery is running both the trailer lights and tow vehicle lights 3 2 COUPLING AND UNCOUPLING THE TRAILER A secure coupling or fastening of the trailer to the tow vehicle is essential A loss of coupling may result in death or serious injury Therefore you must understand and follow all of the instructions for coupling The following parts are involved in making a secure coupling between the trailer and tow vehicle Coupling That part of the trailer connecting mechanism by which the connection is actually made to the trailer hitch This does not include any structural member extension of the trailer frame or brake controller Hitch That part of the connecting mechanism including the ball support platform and ball and those components that extend and are attached to the towing vehicle including bumpers inte
96. proper torque Lug nuts are also prone to loosen after first being assembled When driving a new trailer or after wheels have been remounted check to make sure they are tight after the first 10 25 and 50 miles of driving and before each tow thereafter Failure to perform this check can result in a wheel separating from the trailer and a crash leading to death or serious injury WARNING Lug nuts are prone to loosen after initial installation which can lead to death or serious injury Check lug nuts for tightness on a new trailer or when wheel s have been remounted after the first 10 25 and 50 miles of driving General Safety Information A WARNING Improper lug nut torque can cause a wheel separating from the trailer leading to death or serious injury Be sure lug nuts are tight before each tow 1 2 9 IMPROPER LOADIN The total weight of the load you put in or on the trailer plus the empty weight of the trailer itself must not exceed the trailer s Gross Vehicle Weight Rating GVWR If you do not know the empty weight of the trailer plus the cargo weight you must weigh the loaded trailer ata commercial scale In addition you must distribute the load in the trailer such that the load on any axle does not exceed the Gross Axle Weight Rating GAWR If your trailer is equipped with a Tire amp Loading Information Placard mounted next to the Certification VIN label the cargo capacity weight stated on that placa
97. psi Cold This information indicates the maximum load and tire pressure when the tire is used as a dual that is when four tires are put on each rear axle a total of six or more tires on the vehicle Max Load Single kg Ibs at kPa psi Cold This information indicates the maximum load and tire pressure when the tire is used as a single Load Range This information identifies the tire s load carrying capabilities and its inflation limits 27 Tire Safety Information 2 4 11 TIRE SAFETY TIPS Preventing Tire Damage e Slow down if you have to go over a pothole or other object in the road e Do not run over curbs or other foreign objects in the roadway and try not to strike the curb when parking Tire Safety Checklist e Check tire pressure regularly at least once a month including the spare e Inspect tires for uneven wear patterns on the tread cracks foreign objects or other signs of wear or trauma Remove bits of glass and foreign objects wedged in the tread Make sure your tire valves have valve caps Check tire pressure before going on a long trip Do not overload your vehicle Check the Tire Information and Loading Placard or User s Manual for the maximum recommended load for the vehicle 28 Coupling to Tow Information 3 COUPLING TO THE TOW VEHICLE Follow all of the safety precautions and instructions in this manual to ensure safety of persons cargo and satisfactory life of the trailer 3 1
98. r or substitute and hydraulic components on the dump trailer The hoist system is designed with each component being compatible with the safe and reliable operation of the hoist system Under no circumstances should you alter the hydraulic pressure or flow rate to the hoist system Always have the hoist system repaired or maintained by a qualified technician 63 Loading the Trailer 4 4 6 Bopy PROP The body prop supplied as part of the trailer is to be used only when the dump body is empty The purpose of the body prop is a back up to the hydraulic system and will hold the empty dump body in a raised position while performing maintenance on the hoist trailer body or the trailer itself DO NOT use the body prop to support a loaded dump body DO NOT perform maintenance under a raised dump body without first blocking the empty dump bed up with the body prop A WARNING Risk of Death by crushing Dump body can drop unexpectedly Never go under a raised dump body Use body prop for maintenance A WARNING Risk of Death by crushing Make sure dump body is empty DO NOT manipulate the body prop if a person is near the control 4 4 7 UNLOAD BULK MATERIAL USING THE SPREADER GATE e Read and understand the hoist operating procedure before operating the dump body e Clear the area around the dump trailer e Park the tow vehicle and trailer on a firm and level surface both left right and front rear Attempting to unlo
99. r proceeding all costs and expenses including attorney s fees and costs incurred in such action or proceeding including costs on appeal or in the enforcement of any settlement or judgment PRIOR WRITTEN CONSENT REQUIRED Any repairs made other than at the Walton Trailers factory must first be authorized in writing by Walton Trailers No reimbursement will be made to any dealer or owner for repairs made without the prior written consent of Walton Trailers WALTON TRAILERS MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES AND THERE ARE NO OTHER WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION OF THIS LIMITED WARRANTY COMPONENTS NOT MANUFACTURED BY WALTON TRAILERS ARE EXCLUDED FROM WALTON TRAILERS WARRANTY 86 Tires axles wheels brakes brake components springs suspension components hitch components cylinders hoists pumps controls lights all electrical couplers jacks batteries and any other item purchased and installed by Walton Trailers are warranted by their manufacturers and are excluded from this Limited Warranty Walton Trailers will supply contact information to the applicable vendor on all warranty claims on behalf of the original purchaser for any of the above mentioned parts REQUIRED WARRANTY CLAIM PROCEDURE 1 The original copy of this warranty form must be signed by the dealer and the purchaser It must be postmarked or faxed to Walton Trailers no later than ten 10 calendar days following the purchase of your Walto
100. r tires or vehicle can safely handle avoiding road hazards and inspecting tires for cuts slashes and other irregularities are the most important things you can do to avoid tire failure such as tread separation or blowout and flat tires These actions along with other care and maintenance activities can also e Improve vehicle handling e Help protect you and others from avoidable breakdowns and accidents 21 Tire Safety Information e Improve fuel economy e Increase the life of your tires This booklet presents a comprehensive overview of tire safety including information on the following topics e Basic tire maintenance e Uniform Tire Quality Grading System e Fundamental characteristics of tires e Tire safety tips Use this information to make tire safety a regular part of your vehicle maintenance routine Recognize that the time you spend is minimal compared with the inconvenience and safety consequences of a flat tire or other tire failure 2 4 1 SAFETY Finsr BAsic TIRE MAINTENANCE Properly maintained tires improve the steering stopping traction and load carrying capability of your vehicle Underinflated tires and overloaded vehicles are a major cause of tire failure Therefore as mentioned above to avoid flat tires and other types of tire failure you should maintain proper tire pressure observe tire and vehicle load limits avoid road hazards and regularly inspect your tires 2 4 2 FINDING YOUR VEHICLE S REC
101. ract the axle weight from the total weight to determine the hitch weight 56 Loading the Trailer While you are at the scale you should weigh the entire combination vehicle This result should be less than the Gross Combined Weight Rating GCWR for your towing vehicle Some scales allow you to get individual axle weights also If this is possible get the tow vehicles front and rear axle weights to make sure they are in the same proportion as the tow vehicle alone and that the rear axle is not overloaded This is the best way to check that a weight distribution or load leveling hitch is adjusted properly i e you have the proper number of chain links attached to the snap up brackets 4 3 SECURING THE CARGO Since the trailer ride can be bumpy and rough you must secure your cargo so that it does not shift while the trailer is being towed A WARNING Shifting cargo can result in loss of control of the trailer and can lead to death or serious injury Tie down all loads with proper sized fasteners ropes straps etc 4 3 1 DISTRIBUTING THE CARGO OPEN TRAILER Couple the trailer to the tow vehicle before loading This is essential for the bumper pull trailer because the tongue of a bumper pull trailer can rise during loading before the cargo is properly distributed To measure the tongue weight you will have to uncouple the trailer after it is loaded Do not transport people containers of hazardous substances ca
102. rand models Walton trailers are recognized by the model number and VIN assignment on both a VIN tag and on the MSO Walton Trailers warrants that each trailer operated by the original retail purchaser under normal intended use in the United States Canada will be free from structural defects in materials and workmanship for the warranty periods and pursuant to the terms set forth herein subject to the requirements exclusions and limitations stated below will be strictly applied YOU MUST SEND US A SIGNED COPY OF THIS WARRANTY In order to validate this Limited Warranty the original copy of this form signed by the dealer and the original purchaser must be postmarked to Walton Trailers PO Box 6187 Logan Utah 84341 or faxed to 435 753 5557 no later than ten 10 calendar days following the purchase of the Walton model trailer f this signed warranty is not postmarked or faxed by the tenth calendar day after the purchase of the trailer all express warranties contained in this limited warranty shall be null and void WALTON TRAILERS LIMITED WARRANTY Subject to the requirements exclusions and limitations stated below the structure of your Walton Trailer is warrantied to the original retail purchaser against defects in materials and workmanship by Walton Trailers arising from normal intended use for one 1 year from the date of purchase The structure is that portion of the trailer which includes the main frame tilt frame if applicable
103. rd is only a close estimate The GVWR and GAWR s are listed on the Certification VIN label mounted on the front left side of the trailer A WARNING An overloaded trailer can result in loss of control of the trailer leading to death or serious injury Do not exceed the trailer Gross Vehicle Weight Rating GVWR or an axle Gross Axle Weight Rating GAWR Do not load a trailer so that the weight on any tire exceeds its rating 1 2 10 UNSAFE LOAD DISTRIBUTION Improper front rear load distribution can lead to poor trailer sway stability or poor tow vehicle handling Poor trailer sway stability results from tongue weights that are too low and poor tow vehicle stability results from tongue weights that are too high Refer to Chapter heading Loading the Trailer for more information In the table below the second column shows the rule of thumb percentage of total weight of the trailer plus its cargo Gross Trailer Weight or GTW that should appear on the tongue of the trailer For example a trailer with a gooseneck hitch with a loaded weight of 12 000 pounds should have 20 25 of 12 000 pounds 2400 3000 Ibs on the gooseneck A dump trailer will have the proper weight distribution if the load is evenly distributed in the dump bed For non flowable discrete loads locate the load such as to provide the proper tongue weight After loading be sure to check that none of the axles are overloaded General Safety Inf
104. receiver manufacturer s manual for other inspection and maintenance activities If you do not have a manual for the receiver call Walton Trailers at 435 753 5444 for a free copy If you see or can feel evidence of wear such as flat spots pitting or corrosion on the ball or receiver immediately have your dealer inspect them to determine the proper action to prevent possible failure of the ball and receiver system When replacing a ball the load rating must match or exceed the GVWR of the trailer 8 2 5 3 Fifth Wheel Kingpin Before each tow inspect the fifth wheel and kingpin for wear and coat the contact surface of the fifth wheel plate with water resistant Lithium base grease If you see evidence of wear on the fifth wheel or kingpin immediately have your dealer inspect them to determine the proper action to prevent failure of the fifth wheel and kingpin system See the manual prepared by the manufacturer of the fifth wheel and kingpin for other inspection and maintenance activities If you do not have this manual call Walton Trailers at 435 753 5444 for a free copy 8 2 6 LANDING LEG OR JACK If a grease fitting is present you must use a grease gun to lubricate the jack mechanism Grease the gears in the top of hand cranked jacks once a year by removing the top of the jack and pumping or hand packing grease into the gears 8 2 7 LIGHTS AND SIGNALS Before each tow check the trailer taillights stoplights turn signals and any
105. s From Modifying Your Trailer a se 11 1 2 15 Hazards for Dump Trailers seen 11 1 2 16 Safety Warning Labels on Your Trailer sssssss 12 1 2 17 Trailer Towing Guide sse 13 1 2 18 Reporting Safety Defects sss 14 1 3 SAFE TRAILER TOWING GUIDELINES eeeenme 14 2 TIRE SAFETY INFORMATION cessere eren enne enne 16 2 1 STEPS FOR DETERMINING CORRECT LOAD LIMIT TRAILER 17 2 1 1 Trailers 10 000 Pounds GVWR or Less nn 17 2 1 2 Trailers Over 10 000 Pounds GVWR Note These trailers are not required to have a tire information placard on the vehicle 17 2 2 STEPS FOR DETERMINING CORRECT LOAD LIMIT TOW VEHICLE 17 2 3 GLOSSARY OF TIRE TERMINOLOGY esee nennen 18 2 4 TIRE SAFETY EVERYTHING RIDES ON IT sese 21 2 4 1 Safety First Basic Tire Maintenance ssssssssss 22 2 4 2 Finding Your Vehicle s Recommended Tire Pressure and Load Limits 22 2 4 8 Understanding Tire Pressure and Load Limits 22 2 4 4 Checking Tire Pressure sss 23 2 4 5 Steps for Maintaining Proper Tire Pressure sss 23 2 4 6 TIG Size xe tet tole 24 2 4 7 Tire read ioc te D eee e tod t bre e eda 24 2 4 8 Tire Balance and Wheel Alignment
106. s manual Our trailers are built with components produced by various manufacturers Some of these items have separate instruction manuals Where this manual indicates that you should read another manual and you do not have that manual call Walton Trailers at 435 753 5444 for a free copy General Safety Information The safety information in this manual is denoted by the safety alert symbol amp The level of risk is indicated by the following signal words DANGER Immediate hazards which WILL result in severe personal injury or death if the warning is ignored A WARNING WARNING Hazards or unsafe practices which COULD result in severe personal injury or death if the warning is ignored CAUTION Hazards or unsafe practices which could result in minor or moderate injury if the warning is ignored NOTICE Practices that could result in damage to the trailer or other property 1 2 MAJOR HAZARDS Loss of control of the trailer or trailer tow vehicle combination can result in death or serious injury The most common causes for loss of control of the trailer are e Improper sizing the trailer for the tow vehicle or vice versa Excessive Speed Driving too fast for the conditions Failure to adjust driving behavior when towing a trailer Overloading and or improper weight distribution Improper or mis coupling of the trailer to the hitch Improper braking and steering under sway conditions Not maintain
107. smatch can result in uncoupling leading to death or serious injury Be sure the LOAD RATING of the hitch ball is equal or greater than the load rating of the coupler Be sure the SIZE of the hitch ball matches the size of the coupler The height of the ball receiver on the trailer must be adjusted to match the height of the gooseneck ball on your tow vehicle so that There is clearance between the bottom of the trailer and the sides of the tow vehicle bed and The trailer is level and allows equal weight distribution on tandem axles The Gooseneck Ball Receiver and Height Adjustment figure shows the gooseneck height adjustment The gooseneck height adjustment bolts which have a cup that makes a gripping impression into the gooseneck tube must be tight so that the trailer does not drop to a lower position Do not over tighten because the tube can be deformed After tightening the bolts tighten the jam nuts on the bolts Gooseneck Ball Receiver and Height Adjustment 43 Coupling to Tow Information WARNING Improper gooseneck height adjustment can result in overloaded tires blowout and loss of control leading to death or serious injury Adjust the gooseneck receiver so that the loaded trailer is level A trailer having a gooseneck hitch will have one or two drop leg jacks for raising and lowering the gooseneck ball receiver Because several drop leg jack mechanisms are available the general
108. t whether installed or not Bead The part of the tire that is made of steel wires wrapped or reinforced by ply cords and that is shaped to fit the rim Bead separation This is the breakdown of the bond between components in the bead Bias ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread Carcass The tire structure except tread and sidewall rubber which when inflated bears the load Chunking The breaking away of pieces of the tread or sidewall 18 Cold inflation pressure The pressure in the tire before you drive Cord The strands forming the plies in the tire Cord separation The parting of cords from adjacent rubber compounds Cracking Any parting within the tread sidewall or inner liner of the tire extending to cord material CT Apneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel oil and coolant and if so equipped air conditioning and additional weight optional engine Extra load tire A tire designed to operate at higher loads and at higher inflation pressures t
109. teriorate 1 2 3 FAILURE TO ADJUST DRIVING BEHAVIOR WHEN TOWING A TRAILER When towing a trailer you will have decreased acceleration increased stopping distance and increased turning radius which means you must make wider turns to keep from hitting curbs vehicles and anything else that is on the inside corner Furthermore the trailer will change the handling characteristics of your towing vehicle making it more sensitive to steering inputs and more likely to be pushed around in windy conditions or when being passed by large vehicles In addition you will need a longer distance to pass due to slower acceleration and increased length With these caveats in mind e Be alert for slippery conditions You are more likely to be affected by slippery road surfaces when driving a tow vehicle with a trailer than driving a tow vehicle without a trailer e Anticipate the trailer swaying Swaying can be caused by excessive Steering wind gusts roadway edges or by the trailer reaction to the pressure wave created by passing trucks and busses e When encountering trailer sway take your foot off the gas and steer as little as possible in order to stay on the road Use small trim like steering adjustments Do not attempt to steer out of the sway you ll 3 General Safety Information only make it worse Also do not apply the tow vehicle brakes to correct trailer swaying On the other hand application of the trailer brakes alone w
110. that allow you to safely observe approaching traffic 1 2 14 HAZARDS From MODIFYING YOUR TRAILER Essential safety items can be damaged by altering your trailer Even simply driving a nail or screw to hang something can damage an electrical circuit or other feature of the trailer Before making any alteration to your trailer contact your dealer or Walton Trailers at 435 753 5444 and describe the alteration you are contemplating Alteration of the trailer structure or modification of mechanical electrical or other systems on your trailer must be performed only by qualified technicians who are familiar with the system as installed on your trailer 1 2 15 HAZARDS FOR DUMP TRAILERS A dump trailer is specifically designed for hauling cargo that is to be dumped not for transporting equipment or livestock The major hazards associated with dump trailers are e Overloading Improper weight distribution both side to side and front to back Getting under a raised dump bed Not using or improperly using the body prop Modifying or altering hydraulic components Modifying or altering dump controls Not dumping from a solid and level foundation Not fully opening rear doors when dumping Jerking the trailer or hydraulics to loosen the load See Section 4 4 for more details on these hazards 11 General Safety Information 1 2 16 SAFETY WARNING LABELS ON YOUR TRAILER Figure 1 1 Warning Labels and Locations UT0019 Tire Warning UT0019
111. tions 2 4 10 2 UTQGS Information Treadwear Number This number indicates the tire s wear rate The higher the treadwear number is the longer it should take for the tread to wear down For example a tire graded 400 should last twice as long as a tire graded 200 Traction Letter This letter indicates a tire s ability to stop on wet pavement A higher graded tire should allow you to stop your car on wet roads in a shorter 26 Tire Safety Information distance than a tire with a lower grade Traction is graded from highest to lowest as AA A B and o Temperature Letter This letter indicates a tire s resistance to heat The temperature grade is for a tire that is inflated properly and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat build up and possible tire failure From highest to lowest a tire s resistance to heat is graded as A B or C Additional Information on Light Truck Tires Please refer to the following diagram Maximum load Load amp inflation when used as a dual Severe snow Light conditions Maximum load amp inflation when Load inflation used as a single limits Tires for light trucks have other markings besides those found on the sidewalls of passenger tires LT The LT indicates the tire is for light trucks or trailers ST An ST is an indication the tire is for trailer use only Max Load Dual kg Ibs at kPa
112. to a gooseneck ball that you must have installed in the bed of the tow vehicle This system of coupling a trailer to a tow vehicle permits the tow vehicle to turn to sharper angles than are permitted by a bumper hitch system A gooseneck coupler consists of a tube in an inverted U shape and a gooseneck ball receiver Trailer with Gooseneck Hitch Coupler figure shows a trailer with a gooseneck coupler 41 Coupling to Tow Information Trailer with Gooseneck Coupler We have installed a Gooseneck ball receiver that is suitable for the size and weight of the trailer The load rating of the coupler and the necessary ball size are listed on the gooseneck You must provide a gooseneck ball and support structure that is marked with a rating that meets or exceeds the GVWR of your trailer and matches the size of the gooseneck ball receiver If the gooseneck ball is too small is underrated is loose or is worn the trailer can come loose from the tow vehicle and may lead to death or serious injury THE TOW VEHICLE SUPPORT STRUCTURE AND GOOSENECK BALL MUST HAVE A RATED TOWING CAPACITY EQUAL TO OR GREATER THAN THE TRAILER GROSS VEHICLE WEIGHT RATING GVWR IT IS ESSENTIAL THAT THE GOOSENECK BALL BE OF THE SAME SIZE AS THE GOOSENECK BALL RECEIVER The ball size and load rating capacity are marked on the ball hitch capacity is marked on the hitch 42 Coupling to Tow Information WARNING Coupler to hitch mi
113. trailer on the road until Tires and wheels are checked The trailer brakes are checked The breakaway switch is connected to the tow vehicle and the break away battery is checked The load is secured to the trailer and The trailer lights are connected and checked 33 Coupling to Tow Information 3 2 1 Various COUPLER DESIGNS Trailers are produced with a variety of coupler devices One of the sections below will pertain to your trailer Bumper pull Ball Hitch Coupler Gooseneck Hitch Coupler Fifth Wheel Coupler If the coupler on your trailer does not resemble one of the couplers shown in the figures see the separate coupler instructions If you do not have separate coupler instructions call Walton Trailers at 435 753 5444 for a free copy 3 2 2 TRAILER WITH BALL HiTCH COUPLER A ball hitch coupler connects to a ball that is located on or under the rear bumper of tow vehicle This system of coupling a trailer to a tow vehicle is sometimes referred to as bumper pull A ball hitch trailer may be fitted with a tongue jack that can raise and lower the coupler The tongue jack is mounted to the A frame front or tongue part of the trailer By rotating the jack handle clockwise the jack will extend and raise the tongue of the trailer Trailer with Ball hitch Coupler Uncoupling will cause trailer to come loose from tow vehicle You must CHECK that ball LOAD RATING is same uw clamp as or greater t
114. trolled via a connection to the tow vehicle generally a multi pin electrical connector Check the trailer tail lights by turning on your tow vehicle headlights Check the trailer brake lights by having someone step on the tow vehicle brake pedal while you look at trailer lights Do the same thing to check the turn signal lights If your trailer has electric brakes your tow vehicle will have an electric brake controller that sends power to the trailer brakes Before towing the trailer on the road you must operate the brake controller while trying to pull the trailer in order to confirm that the electric brakes operate While towing the trailer at less than 5 10 General Safety Information mph manually operate the electric brake controller in the tow vehicle cab You should feel the operation of the trailer brakes A WARNING Improper electrical connection between the tow vehicle and the trailer will result in inoperable lights and electric brakes and can lead to collision Before each tow e Check that the taillights brake lights and turn signals work e Check that the electric brakes work by operating the brake controller inside the tow vehicle If your trailer has hydraulic surge brakes pull the emergency break away brake lanyard to check the operation of the surge mechanism Standard mirrors usually do not provide adequate visibility for viewing traffic to the sides and rear a towed trailer You must provide mirrors
115. vehicle and trailer must be on level ground as they will be when the trailer is being towed For lighter trailers the recommended method of checking tongue weight is to use an accessory called a tongue weight scale If a tongue weight scale is not available from your dealer call Walton Trailers at 435 753 5444 for assistance An alternate method of checking tongue weight involves the use of a bathroom scale The loaded trailer must be on a smooth and level surface and you must block the trailer wheels front and rear Checking Tongue Weight Using a lever and bathroom scale 55 Loading the Trailer A WARNING An unrestrained trailer can fall off its support resulting in serious injury or death Before checking tongue weight block trailer wheels front and rear Raise the tongue of the trailer with the jack Place a bathroom scale on the ground directly below the coupler Place a strong block support such as a cement block on the scale note the scale reading for the weight of the block support Lower the tongue until the coupler rests on the block support and the jack is Ve inch above the ground The scale reading minus the weight of the block support is the tongue weight If the tongue weight exceeds the capacity of a bathroom scale you can use leverage to divide the tongue weight between the bathroom scale and another support see Checking Tongue Weight figure e Raise the tongue of the tr
116. ween you your dealer or Walton Trailers To contact NHTSA you may either call the Vehicle Safety Hotline toll free at 1 888 327 4236 TTY 1 800 424 9153 go to http www safercar gov or write to Administrator NHTSA 1200 New Jersey Ave SE West Building Washington DC 20590 You can also obtain other information about motor vehicle safety from http www nhtsa gov Call 435 753 5444 to reach Walton Trailers 1 3 SAFE TRAILER TOWING GUIDELINES e Recheck the load tiedowns to make sure the load will not shift during towing e Before towing check coupling safety chain safety brake tires wheels and lights e Check the lug nuts or bolts for tightness e Check coupler tightness after towing 50 miles e Adjust the brake controller to engage the trailer brakes before the tow vehicle brakes Follow the instructions given with the brake controller manufacturer s literature 14 General Safety Information Use your mirrors to verify that you have room to change lanes or pull into traffic Use your turn signals well in advance Allow plenty of stopping space for your trailer and tow vehicle Do not drive so fast that the trailer begins to sway due to speed Generally never drive faster than 60 m p h Allow plenty of room for passing A rule of thumb is that the passing distance with a trailer is 4 times the passing distance without a trailer Shift your automatic transmission into a lower gear for city driving Use lower g
117. y which can result in a tire blowout or possible loss of control Therefore before each tow you must also check the tire pressure Remember the proper tire pressure is listed on the Certification VIN label normally mounted on front left side of the trailer and should be checked when tires are cold Allow 3 hours cool down after driving as much as 1 mile at 40 mph before checking tire pressure General Safety Information A WARNING Improper tire pressure can result in a blowout and loss of control which can lead to death or serious injury Be sure tires are inflated to pressure indicated on the Certification VIN label before towing trailer The tightness of the lug nuts is very important in keeping the wheels properly seated to the hub Before each tow check to make sure they are tight A WARNING Metal creep between the wheel rim and hub may cause lug nuts to loosen and could result in a wheel coming off leading to death or serious injury Tighten lug nuts before each tow The proper tightness torque for lug nuts is listed in Section 8 2 11 2 in the Inspection and Service Instructions chapter of this manual Use a torque wrench to tighten the lug nuts use the crisscross star pattern on page 82 If you do not have a torque wrench use a lug wrench from your tow vehicle and tighten the nuts as much as you can At the first opportunity have a service garage or trailer dealer tighten the lug nuts to the

Download Pdf Manuals

Related Search

Related Contents

User Manual - Howard Computers  Verrou KS KS-Riegel D F GB KS-lock  User Manual - RS Components International  ASP GmbH & Co KG Impianti per la raccolta di acqua  MODE D`EMPLOI USER MANUAL  Bedienungsanleitung    

Copyright © All rights reserved. Failed to retrieve file