SLIDING GATE OPENER CONTROL BOARD SL1600 USER MANUAL
Contents
1. SLIDING GATE OPENER CONTROL BOARD SL1600 USER MANUAL I Safety Instruction A5 1 For security please read instructions carefully before initial operation making sure that the power is off before connection Please clear the memory before initial operation Ref Erasing ALL learned memorized Transmitters Do not learn the remote control when motor is operating in order to avoid mis operation The received signal may be interfered by other communication devices e g the wireless control system with the same frequency range It is forbidden to control the high risk coefficient equipment system e g cranes It is used only for the manual remote control and wireless control equipment system which must not endanger life or property during running failure or its security risks have been eliminated 7 Itshould be applied in dry indoor place or in the electric appliance place II Technical Index 1 Working voltage 220VAC 110VAC 50Hz 60HZ 2 Temperature range 20 C to 60 C 3 Loading capacity 1HP 250VAC 4 Built in fuse 10A please exchange appropriate fuse according to loading capacity 5 Time of Soft start amp soft stop 4S 6S 6 7 8 Nuns wN Operation time adjustable from 10S to 130S Working frequency 433 92MHz Transmitters stored 30 300PCS 9 Size 150 77 38 HI Wire connection As shown A 12 13 Connector for photocell protection switch NC contact B 10 11 24VAC output can power supply the phot2. ocell As shown A 1 2 3 4 For working voltage 220VAC 110VAC B 5 6 Connector for flash lamp C 8 Connector for motor common Single phase AC motor As shown DIP switch 2 in OFF position connector limit switch is Normal Open External limit switch IV Set up AC power supply 14 15 16 for port 1 7 Connector for motor running port 1 9 Connector for motor running port 2 D 7 9 Connector for motor starting Capacitance Photocell 24VAC output As shown DIP switch 2 in ON position connector 14 15 16 for limit switch is Normal Close External limit switch External switch C If no need of using photocell make connector 12 13 short circuit with terminated line the connector is short circuit when leave factory As shown Connector 17 18 19 20 21 for external close stop open loop control control systems is the same as using transmitter 4 1 Learning transmitters Press the learning button LED is on enters into the learning memorizing transmitter process Press the same button twice LED blinks for several times then off The learning process is successful Ignore this step if transmitter already matches the opener before delivery 4 2 Erasing transmitter Press the learning button continue pressing for 8s until LED turns off Release learning button LED will be on about 1s and then off the erasing process is successf
3. r button 1 OPEN Photocell Press Max Press protection running transmitter transmitter running button 2 button 2 time time 5 2 Single button control process DIP 1 at OFF position STOP OPEN Press Max transmitter running button 1 time STOP Press transmitter button 1 CLOSE Photocell Max Description Single button control press open press stop press st op Only the learned button is effective in the transmitter original button is not effective any more when a new button has been learned in the same transmitter For example button 1 was learned firstly button 2 or 3 has been learned of the same transmitter afterwards then button 1 was not effective any more Press transmitter protection running time button 1 SL1600 433 92Mhz Rolling 220VAC SL1620 433 92Mhz Rolling 110VAC SL1601 433 92Mhz Rolling 300 220VAC SL1621 433 92Mhz Rolling 300 110VAC
4. ul Ignore this step if transmitter already matches the opener before delivery 4 3 Opening closing limit adjustment Remote control the door or move the door manually adjust the position of limit device to make sure the door would touch the limit switch when open or close the door LED LD5 DL6 in the controller will be off when limit device touches limit switch 4 4 Running time waiting time adjustment Adjust potentiometer T Normal to change the running time 10 130s of motor Adjust it to make the running time slightly longer 1 2s than opening time that it needs Adjust potentiometer T Wait to change the time that between door opening to auto closing 10 130s This function is available when DIP 1 is at ON position 4 5 Photocell protection function test Photocell connector connects the NC contact of photocell switch DL7 LED turn on after the connection And DL7 LED turn off when blocking out the transmit or receive signal of photocell artificially 4 6 DIP Switch set DIPI VON Auto close is effective OF Auto close is off DIP3 ON or OFF can change the current DIP2 operating direction of motor ON External limit NC switch o i opener can be chosen to install on OFF External limit NO switch right side or left side of the door DIP4 ON Three button control OF Single button control 5 1 Three button control process DIP 1 at ON position STOP Press transmitter button 3 Press transmitte
Download Pdf Manuals
Related Search