Instruction Manual - North American Cable Equipment
Contents
1. Operate the PTZ controller to begin recording movements The count starts at 1 and records up to 100 movements Press IRIS key to save the motion and return to the previous menu STORAGE USED 1 3 9 lt CAMERA gt Lens settings Languages Chinese English Multiples Display ON OFF AGC 180 Backlight compensation ON OFF Shutter setting AUTO Focus setting AUTO Brightness setting 110 Sharpness Setting 013 Day amp night switch AUTO Negative Set OFF Lens Set OFF Default setting OFF lt CRUISE gt CRUISE Menu function descriptions DWELL TIME seconds sane the camera waits on each preset Cruise list of preset points There are 3 pages PRESET LST each page can contain 10 preset points 1 ON O OFF Select preset points are included in the cruise 1234567890 PRESET scan tour Press IRIS key to change 1 is 1111111111 1 10 selected 0 is skipped BACK Return to the previous menu EXIT Exit the menu lt IR SETTING gt IR SETTING Menu function descriptions ON IR light is always on OFF IR light is always IR MODE AUTO off AUTO IR light is switched on and off automatically Sets brightness level at which the IR LEDs will turn IR ONSENS on Range 81 254 Sets brightness level at which the IR LEDs will turn ERER off Range 81 254 BACK Return to the previous menu EXIT Exit the menu setting 3 12 lt DISPLAY SETUP gt DISPLAY2. 1 Choosing SOFT allows the address to be set in the menu below If SOFT is selected above enter the desired address ADOR SOPI here The address range is 1 254 ADDR HARD 1 Always displays the DIP switch address 1 BACK RESET Restore the factory default settings EXIT Exit the menu Note Immediately after setting a new soft address the camera will no longer respond on the previous address Make sure to set the PTZ controller to the new address to regain control of the camera Access to the internal DIP switches requires extensive disassembly of the camera It is highly recommended to use soft addressing lt MOTION gt MOTION Menu function descriptions SET FRAME SCAN Setthe left and right limit points for a LR scan POWER UP Set which action the camera performs on boot up How long the dome must sit idle before the PARK PARETIME ACTION is taken PARK ACTION Perform an action when the camera is idle Set the L R scan speed of the camera FRAME GCAN SPEED Range 1 Slowest 32 Fastest RANDOM SCAN Set the intermittent scan speed of the camera SPEED Range 1 Slowest 32 Fastest BACK Return to the main menu EXIT Exit the menu setting lt SET FRAME SCAN gt L R scan FRAME SCAN Menu function descriptions SET SCAN POSITION Set the Left amp Right scan limit positions CLEAR FRAME SCAN Clear left and right limit positions BACK Return to the previous menu EXIT Exit the menu SET SCA
3. Ipc Wall mount bracket Ipc Screws kit lpc User manual Ipc Product Summary 1 1 Technical Parameters Model number 4 INCH MINI HIGH SPEED IR DOME CAMERA Optical focus 10X Image sensor 1 4 CCD Signal mode PAL NTSC Resolution 650TVL Optical focus Manual Auto Digital continuous focusing function Presets 256 Pattern scan 4 Scan Patterns each can record 100 actions Tour scan Up to 30 presets Speed and dwell time can be set Rotation range Horizontal 360 Vertical 180 auto reverse Rotation speed Horizontal amp Vertical Min 0 01 Max 300 s Communications PELCO D and PELCO P OSD Full screen menu Temperature Optional control system Power supply DC12V Material Aluminum amp plastic for indoor use only Environmental 4F 122 F lt 95 RH Equipment installation 2 Setting the Address Baud Rate and Protocol This camera uses the On Screen Menu to change communication settings This is called Soft Addressing The camera comes from the factory with the default settings of e Address 1 e Baud Rate 2400 e Protocol Pelco D To Change the settings use a PTZ controller set the above settings to access the camera s menu by calling Preset 95 then use the menu as indicated in TABLE 3 3 on page 7 of this manual Dome camera dimensions Bracket dimen
4. SETUP Menu function descriptions ZOOM ON OFF Zoom display ON OFF Horizontal Vertical angular coordinate display P T DEG ON OFF ON OFE BRIGHT DATA ON OFF Light source data display ON OFF IR DATA ON OFF IR light data display ON OFF BACK EXIT 11 TROUBLESHOOTING e No picture after applying power i check all plugs and cables are connected to the proper connectors ii ensure your power supply is providing the correct voltage and enough current e The picture has ripples i Check to see if the power supply is experiencing AC ripple If so a filter may be required ii Determine if the monitor is faulty iii Determine if other peripheral equipment is causing the ripple and if so make the necessary adjustments e The picture background continuously changes color A fluorescent lamp s magnetic field may cause color roll If possible increase the distance between the camera and any fluorescent lamps in the vicinity e The picture appears smeared i The power supply voltage level may be unstable Try another power supply ii Ensure the cables are correctly connected and of the right impedance 75 ohms e Other interference may require the use of a SecurityTronix ground loop isolation filter e Power is on but the controller does not work i Check to make sure the DIP switches or software addressing are all set correctly for address baud rate and protocol ii Check that the RS485 wires at
5. the camera and controller have correct polarities The camera colors are Blue A Green B iii Check the integrity and continuity of the Unshielded Twisted Pair UTP cable Additional troubleshooting assistance can be found online at www securitytronix com or email us at Support securitytronix com or call 800 688 9282 Press 3 for tech support then 2 for SecurityTronix
6. N POSITION LEFT LIMIT Operate the PTZ controller to select the left limit POSITION position Press IRIS button to confirm the current IRIS OPEN TO position of the left limit and the menu will prompt CONTINUE to set the right limit position below SET FRAME SCAN Menu function descriptions ee aa Operate the PTZ controller to select the right limit IRIS OPEN TO position Press IRIS button to confirm and return CONTINUE to the previous menu CLEAR FRAME SCAN Pio ena SoA Press IRIS to clear the left and right limit CONTINUE positions and return to the previous menu lt POWER UP gt This menu sets which action is performed when the camera powers up It s useful if there are known issues with blackouts etc Perform area L R scanning action lt PARK ACTION gt This menu sets which action the camera should perform if it sits idle no user input for a predetermined amount of time Perform area L R scanning action lt PATTERNS gt PATTERNS Menu function descriptions PATTERN NUMBER Select pattern number Range 1 4 Used to program a pattern scan The menu PROGRAM RATTERN will prompt the user through the steps lt PROGRAM PATTERN gt USE THE JOYSTICK OR KEYBOARD TO MOVE THE Use the joystick or keyboard to move the CAMERA TO THE STARTING camera to the starting position and press POSITION PRESS IRIS the IRIS key to continue OPEN TO CONTINUE
7. Zan SECURITY TRONIX THE IMAGE OF QUALITY INSTALLATION MANUAL ST PTZMINI IR10XTA High Speed Intelligent IR Dome PTZ Color Camera This is a 12 volt DC camera SECUR SrronIx MAGE OF OL Copyright North American Cable Equipment WARNINGS AND CAUTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECTS THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT CAUTION EXPLANATION OF GRAPHICAL SYMBOLS The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user the presence of AN non insulated dangerous voltage within the product s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to different persons The exclamation point within an equilateral triangle is intended to alert the user the presence of important operating and maintenance servicing instructions in the literature accompanying this product PRECAUTIONS Persons without technical qualifications should not attempt to operate this dome device before reading this manual thoroughly Remove any power to the dome before attempting any operations or adjustments inside the dome cover to avoid potential damage to the mechanism Inside the dome cover there are precision optical and electrical devices Heavy pressure shock and other sudden adjustments or operations should be avoided O
8. cessories specified by the manufacturer 8 Verify that the surface you are planning to use for attaching the dome can adequately support the weight of the device and mounting hardware 9 Protect this device against lighting storms with proper power supplies surge arrestors and other protective precautions 10 Refer all servicing to SecurityTronix service personnel Servicing is required when the device has been damaged in any way when liquid traces are present or the presence of loose objects is evident or if the device does not function properly or has received sever impact or has been dropped accidentally 11 Do not use this product under circumstances exceeding specified temperature and humidity ratings 12 Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged period of time avoiding the risk of permanent damages to the imaging sensor 13 The attached instructions are for use by qualified personnel only To reduce the risks of electric shock do not perform any servicing other than contained in the operating instructions unless you are qualified to do so 14 During usage the user should abide by all electrical safety standards and adhere to electrical specifications for the operation of the dome The control cable for RS485 communications as well as the video signal cables should be isolated from high voltage equipment and high voltage cables 1 Carton Contents IR Speed dome
9. press PRE Preset point function table Call Preset 95 Enter the On Screen menu Call Preset 82 Auto Cruise Call Preset 83 Clear all presets Call Preset 84 Start Pattern scan 1 Call Preset 85 Start Pattern scan 2 Call Preset 86 Start Pattern scan 3 Call Preset 87 Start Pattern scan 4 Call Preset 96 360 degree scan with 90 stops Call Preset 97 Scan between two presets Call Preset 98 Presets cruise Call Preset 99 360 degree continuous scan 5 lt MAIN MENU gt To access the camera s On Screen Display OSD menu call preset 95 using your PTZ controller and the Main Menu screen will appear SYSTEM INFORMATION ADDR SETTING MOTION CAMERA CRUISE SETTING R SETTING DISPLAY SETUP RESTORE FACTORY DEFAULT REBOOT SYSTEM lt SYSTEM INFORMATION gt SYSTEM INFORMATION Menu function descriptions COM 2400 N 8 1 Displays the camera s current Baud Rate ADDRESS 1 Displays the camera s current Address PROTOCOL PELCO D Displays the camera s current Protocol PRESETS 256 Displays the currently selected preset SOFTWARE VERSION V5 2 Displays the current software version EXIT Exit the menu Note The system information such as Address Baud Rate etc shown on this menu cannot be changed on this menu page lt ADDR SETTING gt ADDR SETTING Menu function descriptions Sets either HARD and SOFT addressing Choosing ADDR TYPE HARD will set the dome to address
10. sions System OSD menu settings Power On Self Test When power is connected the camera will perform a self test function by panning and tilting the camera as well as testing zoom After the self test the camera will display the Protocol PTOL Baud Rate COMM and Address ADDR as shown in the diagram below PTOL PELCO D COMM 2400 N 8 1 ADDR 1 Storing saving preset points Using a PTZ controller aim the camera at the desired subject and adjust zoom if desired To store the preset in the camera consult the manual for the specific PTZ controller you are using for how to store a preset Sometimes storing a preset is referred to as writing saving setting or some other similar term For instance on a SecurityTronix ST PTZMINI KB controller the button sequence to STORE preset 1 on a camera is Press SET press 1 press PRE Calling preset points Normally calling a preset will cause the camera to move to the position it was at when that preset number was stored There are a few exceptions such as the preset numbers which are reserved for special functions as listed in the table below To CALL a preset in the camera consult the manual for the specific PTZ controller you are using for how to call a preset For instance on a SecurityTronix ST PTZMINI KB controller the button sequence to CALL preset 1 on a camera is Press 1
11. therwise you may cause irreparable damage to the product Please DO NOT remove or disassemble any internal parts of the video camera to Avoid normal operation and possibly void the warranty There are no serviceable parts inside the camera All electrical connections to the dome should be made in strict accordance with the attached labels and wiring instructions in this manual and in accordance with all local and national electrical codes Failure to do so may damage the dome beyond repair and void the warranty For outdoor installation especially in high places or poles it is highly recommended that the proper lightning arrestors and surge suppressors are installed before the dome is entered into service Do not use the product under circumstances where the environment exceeds the maximum specified temperature humidity or power supply specifications IMPORTANT SAFEGUARDS 1 Read these instructions before attempting installation or operation of this dome 2 Keep these instructions for future reference 3 Heed all warnings and adhere to electrical specifications Follow all instructions 4 Clean only with non abrasive dry cotton cloth lint free and approved acrylic cleaners 5 Should the clear dome of the camera become dirty use a special lens cleaning cloth and solution to properly clean it 6 Do not block any ventilation openings Install in accordance with manufacturer s instructions 7 Use only attachments or ac
Download Pdf Manuals
Related Search