GTR User Manual - RhinoCo Technology
Contents
1. Your Rhino Security system incorporates the latest in high security amp convenience features It is possible to customise your security system so that it suits your requirements perfectly Detailed below is the full list of programmable features that can either be turned on or turned off We have set at the factory the most common configuration chosen and these settings are listed in the REGISTER Settings listed below Once the desired features have been selected the selection is permanently retained in memory even if power is removed To turn on or turn off any feature use the following procedure eg to enable silent arming 1 Arm then disarm the alarm system 2 Within 20 seconds of disarming turn the ignition key to on 3 Press button 1 on the remote control immediately after turning the ignition on an equal number of times to the selected feature s code no eg 10 times for Audible arm disarm Leave a 0 5 sec gap between each press The siren will chirp to confirm each press 4 Immediately turn the ignition to off after the last press 5 The system will now confirm whether the feature has been turned on or off via visual readout One flash of the indicators means the feature is on Two flashes means the feature has been turned off Press INITIAL PROGRAMMABLE Remote This FACTORY FEATURE Many Times SETTING DESCRIPTION Voltage Drop Current Sensing 1 Flash On 2 Flash Off If deactivated this feature will preven2. amp Door Ajar Warning 2 Flash Oft Sec from the intital factory setting of 15 seconds up to 45 seconds Door Ajar Warning When the arming delay is set on 15 sec if a car door is left open when arming the siren will emit an error chirp after the normal arming beep The alarm will also isolate the door trigger input to prevent trigger in case of faulty door pin switch If arming delay is extended from 15 sec this feature will not work This may be necessary in vehicles that have an interior light delay TROUBLE SHOOTING GUIDE FOR RHINO GTR CAR ALARM Golden Rule Check Power amp Earth Connections First POSSIBLE CAUSE SYSTEM BELIEVED TO BE FALSE ALARMING SYSTEM NOT WORKING AT ALL OR REMOTE CONTROLS ARE NOT ARMING OR DISARMING THE SYSTEM VEHICLE WILL NOT START OR VEHICLE ENGINE WILL NOT RUN SYSTEM ARMS WHILE THE ENGINE IS RUNNING ENGINE IMMOBILISATION DOES NOT OPERATE Power supply problem Door or Bonnet Switches may be fautly Impact Sensor sensitivity is set too high Power supply problem Grey wire from the system is connected to constant 12V System is armed Grey wire from the system is connected to constant 12V Immobilisation wiring is incorrect The Grey wire is not connected to the ignition circuit Bad earth The Grey wire is not connected to the correct point Grey wire drops below 12V when the engine is being cranked Power supply prob
3. ARM TRIGGER amp MEMOR When the alarm is triggered the siren will sound for 30 seconds and then will automatically rearm If the alarm has been triggered in your absence the dash LED will be flashing twice as fast as normal when you return to your vehicle EMERGENCY PANIC BUTTON The panic feature is activated by pressing amp holding BUTTON 1 on the remote control transmitter for 2 seconds If disarmed the alarm system will arm first i e lock doors then the siren will sound amp the blinkers will flash for 30 seconds If armed the alarm system will stay armed i e the doors will not unlock amp the siren will sound amp blinkers flash for 30 seconds To cancel panic follow disarm procedure as desribed on page 1 NOTE Panic does not work when the ignition is on by requirement of Australian Law EPA Environmental Protection Authority The features outlined below are the most popular that can be turned on or off to suit your requirements Please refer to the section is this manual marked Rhino Programmable Features for full details PASSIVE ARMING The alarm can automatically arm itself 30 seconds after you leave your vehicle provided that the ignition is turned off and that at least one door has been opened and closed Ie the owner has parked and has exited the vehicle This feature will not lock the vehicle where central locking is connected AUTOMATIC RE ARM This feature prevents accidental disarming by the owne
4. INSTRUCTION MANUAL FOR FuUno Gi Remote Control Car Alarm with Impact Sensor pipliniei me Mini Battery Backup Siren amp Engine Immobiliser SYDNEY AUSTRALIA Build Date Gy A C N 001 621 610 O ARM DISARM ALARM The alarm is activated by pressing BUTTON 1 on the remote control transmitter once The blinkers will flash once and the siren will beep once The dash LED light will stay on for 10 seconds then flash THE ALARM IS NOW ON To deactivate the alarm press the BUTTON 1 again The blinkers will flash twice and the siren will beep twice THE ALARM IS NOW OFF If the siren is sounding and you wish to disarm the first press will cancel the siren the system will then return to an armed state A second press is required to fully turn the alarm off you will hear 2 beeps amp the blinkers will flash twice 31003 W aiJ Available on cars fitted with electric boot release motors The alarm is fitted with remote boot release capability This feature enables the user to unlock the boot by pressing BUTTON 2 for 2 seconds The boot will unlock and the indicators will flash 14 times For safety reasons the remote boot release will not work when the ignition is on DOOR AJAR WARNING amp BYPASS When arming if the alarm senses that a door has been left open 4 seconds after the normal arming beep the siren will beep a further 5 times The door trigger input will be automatically bypassed to prevent false alarms AL
5. ND FROM SIREN STRANGE NOISE FROM SIREN VOLTAGE CURRENT SENSING DOES NOT OPERATE VOLTAGE DROP SENSING FALSE ALARMS AUXILIARY SENSOR FALSE ALARMS Power supply problem Alarm main fuse has blown and the system is utilising the backup battery only where a backup battery system is provided Power supply problem The siren speaker 1s damaged Bad earth If the siren makes unusual noise especially if the car is stopped and alarm is deactivated it is likely that the unit has suffered from water damage If the siren makes a whining noise while the motor is running it is likely that the unit is mounted too close to the vehicles ignition leads The main power wire red has been connected directly to the battery Interior light is not operating correctly Car battery is faulty 1 e does not hold a proper charge Other appliances in the vehicle are drawing power after the alarm system has armed i e engine cooling fans car phone car fridge etc Auxiliary detectors are not adjusted correctly REMEDY Test for good 12V amp earth at the alarm module Test for good 12V amp earth at the alarm module Check main power fuse Test for good 12V amp earth at the alarm module Confirm that the alarm system is arming disarming via flashing LED Trigger alarm Confirm other functions on alarm e g flashing indicators If there is no sound from the siren it most likely has a damaged speaker Cont
6. act your Rhino Dealer Check that the black wire is soldered to a good earth a non insulated metal part of the car body Turn the alarm system completely off 1 e at keyswitch where used Contact your Rhino Dealer Check that all connections to the siren are properly soldered If this does no rectify the problem move the siren to a different location The red wire must be connected to constant 12V via the fuse box at the point where the interior light circuit is powered Voltage sensing will not work if this procedure is not followed The interior light must be set to come on when the vehicle s doors are opened Check the function of the interior light and switch Change the car battery Turn Voltage Drop Sensing off in Programmable Features page 4 Adjust reduce the sensitivity of any Ultrasonic or Microwave sensor fitted with the alarm and test 12 SYMPTOM POSSIBLE CAUSE REMEDY CENTRAL LOCKING MOVES UP amp Central locking motors are not adjusted Adjust the central locking motors so DOWN WHILE DRIVING correctly that they can travel their full displacement without excessive force Bad earth to the alarm module Check that the black wire is soldered to a good earth a non insulated metal part of the car body Bad power connection to the central door Check for 12V amp earth with a test locking motors Usually a bad earth light across the central locking power connection wires normally black and
7. ion to replace each of the 3 memory locations so that the old remote code s are erased E The system will automatically exit the learning mode 20 seconds after the last press of a remote ARIINO GIR Car Alarm amp Immobiliser STANDARD SYSTEM FEATURES e e gt hS e e SS e hS SCS 2S SCS hS SCS hS e hS SCS SS e e e 2 x Remote Controls Smart Code Learning Technology Point Engine Immobilisation Onboard Relay Can Protect Doors Boot Bonnet Car Body Impact Sensor Mini Backup Battery Siren Flashes Indicators Flashing Red Dash Light Central Locking Control for Keyless Entry Arm Disarm Beep Emergency Panic via Remote Car Finder Function Current Voltage Drop Sensing Automatic Siren Reset 30 seconds Security Override Mode Boot Release via Remote where fitted Split System Separate Siren amp Brain SELECTABLE SYSTEM FEATURES oe e e gt SS Passive Arming Auto Rearm amp Relock Audible or Quiet Arm Disarm Current Sensing Voltage Drop Circuit Central Locking Output Time Selectable 0 8 or 5 Seconds OPTIONAL ACCESSORIES Automatic Electric Window Lift Part No GLU400 Closes 2 Windows Paging System Part No APAGER Ultrasonic Sensors Part No UD6 Microwave Sensor Part No UDS PROGRAMMABLE FEATURES ror RAIno GTR Car Alarm
8. lem REMEDY Check 12V amp ground earth at the system module with a test lamp or multi meter Check that switches operate correctly 1 e check interior light switches on every door amp that the bonnet switch is making amp breaking contact correctly Follow appropriate procedures as outlined on page 6 to adjust sensitivity Check 12V amp ground earth at the system module with a test lamp or multi meter The Grey wire must be connected to the vehicle s ignition wire not constant 12V Press the remote until the blinkers flash twice or two disarm beeps are heard This wire must be connected to a 12V ignition switched lead which does not drop to 0 Volts when the engine is being cranked Check the wiring on all points of immobilisation 1 e where starter and or fuel circuits have been cut This wire must be connected to a 12V ignition switched lead which does not drop to 0 Volts when the engine is being cranked This wire must also be constant 12V when the engine is running Check that the black wire is soldered to a good earth a non insulated metal part of the car body Check that this wire is wired to the ignition circuit not to the accessory circuit This wire must be connected to a 12V ignition switched lead which does not drop to 0 Volts when the engine is being cranked Test for good 12V amp earth at the system module 1 POSSIBLE CAUSE LOW VOLUME FROM SIREN NO SOU
9. r ie the owner turns the alarm off but is then distracted and forgets that they have deactivated the system If a door is not opened or the ignition is not turned on within 60 seconds from when the system is turned off by the remote the system will re arm and if central locking is connected it will re lock the vehicle SILENT ARM DISARNM This feature when turned on stops the siren from beeping for arm amp disarm confirmation i e only the blinkers will flash EFAN NRSA ONES Up to 3 remotes can be used with this alarm system Before entering this mode make sure you have all remotes present that you wish yo utilise with this alarm system as the alarm automatically erases all remotes when you enter this mode A Arm then Disarm the alarm system While the system Is disarmed open and close your drivers door get inside the vehicle making sure the interior light is coming on as you open the door B Within 30 seconds turn the car ignition key from the off position to the ignition on position 8 times C 10 seconds later the blinkers will flash 8 times to confirm that you have entered the remote learning mode Repeat steps A amp B if you do not receive the flashes D Now press amp hold Button 1 on the new remote you wish to learn in The siren will beep once to confirm the code has been learnt Repeat this step for up to 3 remotes You can use this process to delete lost remote controls by learning in the same remotes in success
10. red wires Bad fuse Check fuses and replace if necessary NOTES FOR INSTALLATION Check the vehicles electrical system thoroughly before commencing installation The installation should be as well hidden as possible to maximise the system security Solder all connections and then insulate with insulation tape Use a multi meter to verify any wires nature IMPORTANT If the installer does not have a concise knowledge of the vehicle s electrical system it is strongly advised not to aimlessly probe to find the necessary wires Doing so may damage your vehicles electrical system Consult with your vehicle s manufacturer or a qualified Auto Electrician Rhino Alarms accepts no responsibility if an installer wires the product incorrectly or damages the vehicle during installation Ta tt www rhino com au 13
11. t the alarm triggering via sensing a drop in voltage in the vehicle s electrical system This may be necessary where engine thermo fans cut in automatically or there are other accessories active even when the ignition is turned off eg fridges car phones 7 Passive Arming 7 1 Flash On OFF The alarm can automatically arm itself 30 2 Flash Off seconds after you leave your vehicle provided that the ignition is turned off and that at least one door has been opened and closed ie the owner has parked and has exited the vehicle This feature will not lock the vehicle where central locking is connected Da i 1 Flash On 2 Flash Off Auto Re arm If system is disarmed and a door is not opened or the ignition turned on within 60 seconds the system will rearm amp relock where central locking is connected 1 Flash 0 8 2 Flash 5 sec Central Closure 0 8 sec You can select the lock amp unlock outputs to become a 5 second negative pulse instead of 0 8 seconds This feature is for certain vehicles with vacuum central locking or those with a central closure wire some BMW Mercedes ie doors lock electric windows wind up sunroof closes automatically 1 Flash On This feature when turned off stops the 2 Flash Off siren from beeping for arm amp disarm confirmation i e only the blinkers will flash 1 Flash On 15 45 You can increase the arming delay period 4 Audible Arm Disarm Arming Delay Adjustment
Download Pdf Manuals
Related Search