Operating Manual for the KODAK CAROUSEL Slide - Micro
Contents
1. KODAK CAROUSEL Slide Projector 19 Maintenance Projection Lamps To ensure a long life and trouble free operation for your projector e Allow the air to flow freely around the projector e Do not recirculate warm air e Keep the projector dust free Your CAROUSEL Projector requires no lubrication all bearings are self lubricating Included FHS lamp 70 hour lamp life medium brightness Sampling of other lamps EXY 200 hours less brightness EXR 35 hours maximum brightness Note An EXW lamp is not recommended for older models of CAROUSEL Projectors Contact the Kodak Information Center at 1 800 242 2424 in the U S or 1 800 465 6325 in Canada if you need help identifying your particular model Lamp Tips e Projector operation on line voltages above 125 volts greatly reduces the lamp life e Unplug the projector before changing the lamp 20 KODAK CAROUSEL Slide Projector Maintenance Changing the Projection Lamp Slide the power switch to Off and unplug the projector Allow the projector and lamp to cool for about 10 minutes Push the lamp module release button and remove the lamp module Note There is an additional safety latch which reduces the chance of an accident with a loosely inserted lamp module that may cause some resistance To release the latch you may need to apply extra effort when you pull out the module Lift up the lamp release clip Carefully remove the worn lamp from2. You have just purchased a KODAK CAROUSEL Slide Projector which e triples lamp life e provides brighter and more vivid colors Introduction Take the time to read the instructions in this operating manual to become familiar with your KODAK CAROUSEL Slide Projector and how to operate it properly 2 KODAK CAROUSEL Slide Projector Overview FRONT RIGHT 1 Tray 2 Lock Ring 3 Storage Compartment Remote 4 Elevating Foot 5 Elevating Adjustment Wheel 6 Elevating Foot Release Button 7 Lens 8 Viewer Model 5600 9 Focus Knob 10 Select Bar 11 Timer Model 5600 12 Reverse 13 Forward 14 Power Fan Lamp BACK RIGHT 15 Tray Release Latch 16 Lamp Module 17 Reading Light 18 Room Light Outlet Model 5600 19 Remote Control Receptacle BASE 20 Power Cord 21 Power Cord Retainer 22 Leveling Foot KODAK CAROUSELO Slide Projector 3 Operation Operation Startup Open the storage compartment and remove the remote control Storage compartment door an Remote control Plug the 5 pin cable remote connector into the remote control receptacle aligning the raised dot with the metallic rivet head Pome cord a3 7 Hie head Ralsod dot Plug the power cord into a grounded outlet with 110 to 125 volt 60 Hz current only 4 KODAK CAROUSEL Slide Projector Operation L
3. mounts plastic mounts mixed mounts non embossed cardboard mounts rear projection applications duplicated slides A curved field lens works best for e embossed cardboard mounts Embossed mounts have beveled edges around the aperture Kodak Premium Processing and Kodak Processing labs provide embossed mounts Lens Focal Length Use the illustration on the following page to help determine the lens focal Projector Distance _ length and projector distance 4 KODAK CAROUSEL Slide Projector Operation L D 75mm 133 TOD 17 7 125 mm 22 7 150mm 26 6 175 mm 31 0 200mm 354 KODAK CAROUSELO Slide Projector 15 Operation Editing Your Presentation Rem oving the To add or remove slides in the tray you must first remove the lock ring Lock Ring Turn the ring counterclockwise and lift off Rem oving a Slide Rotate the tray to the slide you wish to remove Firmly press and hold down the select bar to eject the slide Adding a Slide When the lock ring is off you can add a slide to any empty slot See Adding Your Slides on page 6 Replace and secure the lock ring 16 KODAK CAROUSELO Slide Projector Operation Clearing a Gate Jam To remove a defective slide or foreign object stuck in the projector gate you need to remove the tray e Slide the tray release latch in the direction of the arrow and e with your other hand lift off the back of the tray With the lock r
4. the socket and place it on a heat resistant surface Insert a new lamp into the socket Push down to tightly seat the replacement lamp Relatch the clip in the forward position and push the lamp module all the way back into v a Lamp the projector until it latches ed Lamp roloa o clip KODAK CAROUSELO Slide Projector 21 Maintenance Cleaning the Condenser Heat Absorbing Glass and Mirror To clean the condenser heat absorbing glass or mirror you must disassemble the lamp module Slide the power switch to Off and unplug the projector Allow the projector to cool about 10 minutes a Push the lamp module release el APN button and remove the lamp module Use a torx head screwdriver to remove the screw a Using a flat blade screwdriver apply ample pressure to release each of the metal tabs Tabs Lift off the top of the lamp module 22 KODAK CAROUSELO Slide Projector Maintenance Condenser Lens You can clean the condenser lens in place or by pulling it out Wear gloves to prevent fingerprints Condenser bens A Caution Heat Absorbing The heat absorbing glass is fragile Handle it only when cool Glass For lamp modules The green tinted heat absorbing glass easily removes for cleaning with a heat absorbing glass Haat abaorbinig glass KODAK CAROUSELO Slide Projector 23 Maintenance Reassembling the To reassemble the lamp module you will need to align and insert each tab
5. Insert your second slide in the second slot with the emulsion dull side facing your first slide and so on 6 KODAK CAROUSELO Slide Projector Operation Replace the lock ring by turning it clockwise until it is secure Tray Place the loaded slide tray on the projector Align the tray index bar with the gate index The tray will drop into position KODAK CAROUSELO Slide Projector 7 Operation Removing the Tray To remove the slide tray press the select bar all the way down e align the tray index bar with the gate index Select bar You can then lift off the tray 8 KODAK CAROUSELO Slide Projector Operation Projecting Your Slides Lens To insert a lens push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector Lamp Slide the power switch to lamp KODAK CAROUSELO Slide Projector 9 Operation Forward and Press the forward button on the projector or the remote control to project the Reverse first slide To change slides briefly press the forward or reverse buttons Focus Focus your first slide using the focus knob on the projector or the focus button on the remote control Models 4400 and 5600 only Focus Autofocus The autofocus feature automatically focuses each slide after you focus your Models 4600 first slide manually If there is a mix of slide mounts in the tray cardboard and 5600 only plastic and glass it may be n
6. Lamp Module into its appropriate slot Start with the tabs in the rear of the lamp module Insert the remainder of the tabs into slots until all 7 tabs on the top and 2 on the bottom are secured Insert the screw and tighten Then insert and seat the lamp 24 KODAK CAROUSELO Slide Projector Maintenance Mirror To clean the mirror invert the lamp module to reach the mirror Gently clean the mirror with a soft lint free cloth moistened with lens cleaner When your maintenance is complete push the lamp module back into the projector Mirrar KODAK CAROUSEL Slide Projector 25 Troubleshooting Consult this guide before calling for service PROBLEM CAUSE CORRECTION Projector does not operate No power to projector Plug power cord into suitable electrical outlet Set power switch to Lamp No illumination on screen with slide in projector gate Power switch on Off or Fan Lamp burned out Lamp not seated in socket Set switch to Lamp Install new lamp or lamp module Check lamp Slide not in proper focus on screen focus Slide itself not sharp First slide in tray not properly focused Slide in different type of mount from others Projection lens installed improperly Examine slide for proper focus Focus center of first slide manually Focus manually Read and follow the instructions for installing the lens Uneven edge to edge focus Slide itself is not
7. Operating Manual KODAK CAROUSEL Slide Projector CONSUMER IMAGING Important Safety Instructions When using your projector always follow basic safety precautions 1 Read and understand all instructions before using this equipment Operate this projector with 110 to 125 volt 60 Hz current only Incorrect voltage can cause projector malfunction Close supervision is necessary when any appliance is used by or near children or others who may not understand the need for these precautions Do not leave the projector unattended during use Be careful not to touch hot parts For lamp replacement allow the module to cool before touching the lamp and the surrounding area Do not place the lamp module on heat sensitive surfaces Do not operate your projector if the cord is damaged or if the projector has been dropped or damaged see How to Obtain Service on page 29 6 Position the cord so that it is not tripped over pulled or placed in contact with hot surfaces 7 If an extension cord is necessary use a cord with a current rating at least equal to that of the projector Cords rated for less amperage than the projector may overheat Always unplug the projector from the electrical outlet before cleaning and servicing and when it is not in use Allow the projector to cool before storing Do not immerse this equipment in water or other liquids Do not disassemble this projector Use a qualifie
8. ctor off at the end of your presentation the room light will come on again Boom Bight gwia 12 KODAK CAROUSEL Slide Projector Operation Si ngle Slides To project single slides slide the power switch on Remove the tray and insert a slide upside down into the projector gate Push the slide all the way down After viewing the slide press forward reverse or the select bar to eject the slide Selecting Slide When buying a lens consider features such as focal length measured in Projection Lenses millimetres aperture designed as an f stop and the lens design curved or flat When selecting a lens remember that the shorter the focal length e the smaller the f number the brighter the projected image Also a curved field lens in combination with cardboard open face mounts from an automated mounting process provide superior projection quality A flat field lens is the best choice for glass mounted slides KODAK CAROUSELO Slide Projector 13 Operation Choosing a Curved The lens you select depends on how you use your projector and what type of or Flat Field Lens slide mount you use So that you may choose the lens that best meets your needs we do not include a lens with the projector To obtain the best results of a projected image insert slides with the emulsion side toward the projection lens slide curve toward the light source A flat field lens works best for general home projection glass
9. d service technician when service or repair is required Incorrect reassembly can cause electric shock the next time the projector is used Use only safety electrical low voltage SELV devices The use of an accessory attachment not recommended by the manufacturer may increase risk of damage Keep the air flow vents unobstructed Save These Instructions Operating Manual KODAK CAROUSEL Slide Projector Contents Important Safety Instructions Inside Front Cover Introductions E e Bed a ede NEE ee bao dee ie tee he one 2 RE 3 Operation s oroe 24d seed tae cae a ea ae 4 Stamp pein Ses ei ev eed Oey Ded oa beled dE ees 4 Loading the Slide Tra 5 Projecting Your Slide 9 Editing Your Presentation 16 Clearing a Gate Jam 17 Using the Built In Viewer Model 5600 Only 18 Shutdown 2 7 Gate tdt teas 19 Maintenance salida abalone ata ee ta weeds 20 Changing the Projection Lamp 21 Cleaning the Condenser Heat Absorbing Glass and Mirror 22 Troubleshooting Ee once eco eee dae po 26 NA EE 28 How to Obtain Service 0 0 eee eect ee eee 29 Serial Number The serial number of your projector is printed on the label affixed to the power cord retainer on the base of the projector Record this number as well as the model identification date and place of purchase for future reference KODAK CAROUSEL Slide Projector 1 Introduction Congratulations
10. e or for assistance in using your KODAK CAROUSEL Slide Projector contact the Kodak Information Center at 1 800 242 2424 Monday through Friday 8 a m to 8 p m Eastern time In Canada call 1 800 465 6325 Monday through Friday 8 30 a m to 5 p m Eastern time Or call Kodak in your country Shipping To help us get your KODAK CAROUSEL Slide Projector back to you Instructions promptly please enclose a note giving details of the problem dated proof of purchase and your complete name and shipping address Pack the unit in a sturdy carton with ample packing material to protect the unit during shipping and handling KODAK CAROUSEL Slide Projector 29 CONSUMER IMAGING EEN Consumer Imaging EASTMAN KODAK COMPANY Rochester New York 14650 www kodak com go projectors Kodak Ektagraphic and Kodalux are trademarks a Part No 5B4904 1 03 Minor Revision EastmanKodak Company Printed In U S A
11. ecessary to manually refocus between mount type changes The focus button on the cabled remote can be used for Models 4400 and 5600 Random Projection For random projection of any slide in the tray e press and hold down the select bar e rotate the tray to the desired slide and e release the select bar 10 KODAK CAROUSELO Slide Projector Operation Screen Image Timer Model 5600 only Use the elevating foot to horizontally center the projected image on the screen To release the foot press the release button while lifting the front of the projector to the desired height Use the elevating wheel to make fine adjustments Ebevating wheel Elevating toot If the image is not level make an adjustment by turning the leveling foot at the rear of the projector To time your slides use the timer switch for slide changes from 3 to 22 seconds To interrupt the timer press either the forward or reverse button For manual operation slide the timer switch to Off KODAK CAROUSEL Slide Projector 11 Operation Reading Light To illuminate a small area for reading lift the reading light cover while the Model 5600 only projector lamp is on Reading light Room Light Outlet Plug any standard room light into the room light outlet and turn it on It will Model 5600 only remain on until the projector is turned to the lamp position when a darkened room is required When you turn the proje
12. ing firmly in place turn the 140 slide tray upside down Retract the tray release latch in the direction of the arrow and align the index hole with the index notch For an 80 slide tray rotate the metal plate until it locks into position Put the tray aside Remove the slide or object from the projector gate by pressing the forward button or removing the slide manually Remount damaged slides to protect your projector and slides from subsequent damage KODAK CAROUSELO Slide Projector 17 Operation Using the Built In Viewer Model 5600 Only A Important Before opening the viewer you must remove the projection lens from the projector Rem oving the Turn the focus knob to the horizontal position Push the knob toward the top Lens of the projector as you withdraw the lens Focus knob Kate Opening the Grasp the viewer handle and pull it out from the base of the projector It will Viewer pop into place Slide the power switch to lamp to project your slides Closing the Viewer To close the viewer fold it and push it back into the body of the projector 18 KODAK CAROUSELO Slide Projector Operation Reinserting the To reinsert the lens push the focus knob up and position the lens gear teeth Lens on the lens barrel with the notch on the projector Focus knot p Shutdown To shut down e remove and store the tray e slide the power switch to off Your projector will remain warm for several minutes
13. nty Limitations Your Rights Under State Law 28 Kodak warrants this KODAK CAROUSEL Slide Projector to function properly for one year from the date of purchase If this KODAK CAROUSEL Slide Projector does not function properly within the warranty period upon submission of dated proof of purchase Kodak will repair it without charge except for worn out projector lamps If Kodak is unable to repair the projector the option of replacement or refund of the purchase price will be available This warranty does not cover circumstances beyond Kodak s control projector lamps or problems caused by failure to follow the care and operating instructions in the manual Any modification to the original design of this projector nullifies this warranty Warranty service will not be provided without dated proof of purchase Kodak makes no other express warranty for this product Repair or replacement is Kodak s only obligation Kodak will not be responsible for any consequential or incidental damages resulting from the sale or use of this projector regardless of the cause of such damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state KODAK CAROUSEL Slide Projector How to Obtain Service Assistance To obtain servic
14. oading the Slide Tray KODAK Slide Trays are available in 80 and 140 slide capacities Use a 140 slide tray if you use thin mounted slides 1 16 in 1 6 mm and need the larger capacity Use an 80 cpacity tray if any of your slides have thick mounts 1 8 in 2 5 mm Note Do not attempt to project slides mounted with sticky or loose tape Place the tray over the center post of the projector Align the 0 slot with the gate index the tray will drop into position If your 140 slide tray does not drop easily secure the lock ring invert the tray and align the index hole with the index notch Slide and hold the tray release latch in the direction of the arrow and turn the bottom plate until the index hole and notch align Then release the latch If you use an 80 slide tray rotate the metal plate on the bottom of the tray until it locks into position is Metal Plate Tray release latch i SL i 140 Slide Tray 80 Slide Tray KODAK CAROUSELO Slide Projector 5 Operation Adding Your Slides Remove the lock ring by turning it counterclockwise and lifting it off Lock ring Check each slide s orientation horizontal or vertical and arrange them in the order you wish to show them Then turn the slides upside down Number each mount in the upper right hand corner of the film s shiny side Insert your first slide into the first slot in the tray so that the number is visible on the outer circumference of the tray
15. sharp Curved field lens used with glass plastic or non embosssed mounts Curved field lens used for rear projection Lamp performance Examine slide Try a flat field lens See Choosing a Curved or Flat Field Lens on page 14 Use a flat field lens Ulnstall new lamp and try again Autofocus has difficulty slide to slide Mixed open and glass slide mounts Do not mix open and glass mounts 26 KODAK CAROUSELO Slide Projector Troubleshooting PROBLEM CAUSE CORRECTION Slide fails to drop into projection position Tray base plate not properly indexed Tray not properly positioned on projector Slide mount warped or frayed at corners slide Projector not level or tilted too high Align the index hole and index notch Reposition tray on projector Straighten mount or remount slide Set projector on a stand equal with center of screen Uneven illumination on screen Projection lamp not fully seated Condenser lens not installed or not positioned properly in mount Slide mount not seated properly in projector gate Check lamp Check condenser lens Check slide position and slide mount condition Projector won t cycle to next slide Tray not properly positioned Slide or foreign object stuck in gate Reposition tray See Clearing a Gate Jam on page 17 27 KODAK CAROUSEL Slide Projector Warranty Warra
Download Pdf Manuals
Related Search