NOTE - TA Triumph
Contents
1. Rough surface Clipped Stapled 7 Chapter 1 Before Use The following kinds of originals can be read with using a carrier sheet Image quality or the reliability of paper feeding for them is not guaranteed Patched Punched 1 12 Chapter 1 Before Use 1 7 Specifications for the Printing Paper 1 7 1 Papers not available to use Do not use the following kinds of printing paper Doing so may damage the print engine Excessively curled a diameter of 50 mm or less Folded 1 13 Chapter 1 Before Use Be KH ee RE CAUTION Do not use the paper with staple or do not use such conductive paper as aluminium foil and carbon paper The above may result in the danger of fire NOTE 1 Print image may become light if printed on a rough surface of the paper 2 Print image may become defective if the print paper has an excess curl 3 It will become a cause for p2. 1 4 3 Scanner part Specification Scanning method Contact Image Sensor CIS 5 pieces of A4 sized CIS LED R G B Setting of original Starting point of scan Min 279 4mm Max 6 000mm Including the margin area Min 210mm Including the margin area Digital resolution 200 300 400 600 dpi Original transportation Sheet through type Transportable original Max 1 60 mm thickness Min 0 05 mm A NOTE lf the original is thicker than 0 6mm its image quality is not guaranteed Scanning speed 65 mm per second NOTE The above specifications are subject to change without notice 1 7 Chapter 1 Before Use 1 5 Appearance 1 5 1 Front view N Main Switch You can turn on off the CX 8048 Original Guides Feed the original under the Scanner Unit along the Original Guides 3 User Interface This is a Touch Screen and many kinds of user operation are available 4 Emergent Stop Button Press this button when you would like to stop copying or scanning emergently Original Tray These trays catch the original ejected from the Scanner Unit 6 Scanner Unit Read the original with this unit when you make scan or copy Toner Hatch Open the Toner Hatch when you replace the Toner Cartridge Original Table Also put the original here and then feed it into the Scanner Unit when you make scan or copy Engine Unit Open Lever Pull up these levers when you open the Engine Unit Ei 9 Bypass
3. i Triumph Adler The Document Business COSOI HNG REALISATION EFFICIENCY Instruction Handbook a E i pech Er Thank you for purchasing the Multi Function Printer CX 8048 This USER S GUIDE contains functional and operational explanations for the CX 8048 Please read this USER S GUIDE carefully before using the Printer Please keep this USER S GUIDE for future reference 1 When this product is installed in North America This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 When this product is installed in Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around other electronic equipment or other precision instruments Other devices may be affected by electrical noise during operation If the Machine is installed near other electronic equipment such as a TV or a radio interference to said equipment such as noise or flickering may occur Use a separate power line and install the PRINTER as far as possible from said
4. 4 Roll Media Replacement EE 2 5 Toner Cartridge Installation nnn 2 10 Cut Sheet Media Placement EE 2 14 Copying nn 9 15 Emergency Stop of Scan or Copy ennai 9 16 C nceling Sleep Mode man an ne na en ea 9 47 Dehumidifying Roll Media EEN 2 18 2 1 Chapter 2 Basic Operation 2 1 Turning on CX 8048 1 Ensure that the CX 8048 is plugged into a dedicated wall outlet A WARNING 1 Do not handle the Power Plug with wet hands or you may receive an electrical shock 2 Make sure to earth the machine for safety 3 Do not plug the printer into a multi wiring connector in which other devices are plugged It may overheat the outlet and may result in a fire 4 The outlet must satisfy the following conditions In U S A 120 V plus minus 10 50 60 Hz and 15 A In Europe 220 240 V plus 6 or minus 10 50 60 Hz and 10 A 2 There is a Power Switch on the right side of CX 8048 Press its side to turn on the CX 8048 Power Switch Press side 2 2 Chapter 2 Basic Operation 3 The User Interface UI starts operating and displays the following Copy Mode Screen in one minute A Ready Indicator on Copy Mode Screen will flash during warming up Ready Indicator V Original Quality Copy Count a a a e FI a Grayscale Advanced Print Quality Normal Width Length Size RECALL JOB SC 100 0 i ez CutSheet Standard Cut son Off copy SCAN JOB ASS Fa Note The scree
5. public or private issued licenses automobile inspection certification IDs and tickets like pass or meal Regulations to control fake currency and Currency Bill Money Bank Note etc Bond Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc Control Law against Forged amp faked Foreign Currency or Foreign Negotiable Foreign Currency Bill Bank Note and Bond Instruments Forged postal stamps control law Unused postal stamps or government postcards Forged revenue stamps control law Government issued revenue stamps and certificate stamps prescribed by Liquor Tax Act or Commodity Tax Act Currency similarity securities Control Law Private issued securities stock draft check goods ticket etc commutation or book tickets Originals protected by the copyright It is prohibited to copy such originals as book music paintings printed copy maps drawings movies and pictures which are protected by the copyright except for personnel or family use or similar purposes 1 3 Chapter 1 Before Use 1 3 Features 1 CX 8048 Digital Printer is a Multi Function Printer which is available for scan copy and print 2 The operation speed is 80mm s 3 4ppm E 5 8ppm D Landscape 3 The maximum print width is 914mm 36 inches wide and the minimum one is 210 mm or 8 5 The maximum print length is 6 000mm in case of 36 inch paper and the minimum one is 210 mm or 8 5 inches
6. Feeder Feed a cut sheet paper from the Bypass Feeder 10 Roll Deck Roll paper can be set here You can set 1 paper roll normally but 2 paper rolls are available if you install the optional 2nd Roll Deck P Prints are stacked here after the ejection It counts the total amount printing Stylus Use this to press buttons on the touch screen 1 8 Chapter 1 Before Use 1 5 2 Rear view No inside the Fuser Unit 2 LAN Port Connect the LAN Cable to connect the CX 8048 Bu to the network Do not connect a telephone line Optional in the US would like to dry the paper in the humid season Inlet Socket Connect the Power Cord here 6 Print Guide Trays These trays guide the prints to the Print Tray P 7 COM Port Optional Connect the cable from the Optional Device D Sub Connector 9 pins 12VDC max 8 USB Port 5VDC max 1 9 Chapter 1 Before Use 1 6 Specifications for the Scan Original A scan original must satisfy the following specifications 0 05 mm to 1 6 mm Width 279 4 mm to 914 4 mm Length 210 mm to 3 600 mm Do not scan the following kinds of originals The original or the scanner may damage Stuck with paste Torn Folded Leading edge Excessively curled a diameter of 50 mm or less V f 1 10 Chapter 1 Before Use Not square Metal or fabric material Rough surface Carbon paper for example Clipped or stapled KIP KIP bet Wet Fabric
7. equipment This product meets the ENERGY STAR guidelines for energy efficiency The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations 2002 96 EC of the European Parliament and the council of 27 January 2003 on waste electrical and electronic equipment WEEE and does not The symbol shown indicates that this product conforms to Directive Si apply to countries outside the EU Only For EU Member States The symbol shown indicates that this product conforms to SJ T 11364 2006 of People s Republic of China Electronic Industry Standard and does not apply to countries outside of People s Republic of China The symbol shown indicates that this product conforms to GB 18455 2001 11364 2006 of National Standard of the People s Republic of China and does not apply to countries outside of People s Republic of China Safety Warnings The following warnings are very important in order to
8. mis fed paper inside the Exit Cover scattered toner can be adhered to the next print 3 1 1 5 Accessory Jam The printing paper is mis fed in the optional device such as Auto Stacker or Folder Remove the mis fed paper making reference to the User s Manual of concerning device 3 8 Chapter 3 Error Correction 3 1 1 6 Original Jam 1 Open the Scanner Unit pulling up the Levers 1 and then remove the original NOTE Press down Scanner Unit on both the sides to close it Do not close it by pressing only one side down 3 9 Chapter 3 Error Correction 3 1 2 Others 3 1 2 1 Initial state This message is indicated when the CX 8048 is turned on for the first time A NOTE You will not find this message because every machine has been turned on at least once before shipment 3 1 2 2 Deck Open This message is indicated when the Roll Deck is opened Close it firmly 3 1 2 3 Accessory Error Any error occurs in the optional device such as Auto Stacker or Folder Clear the error making reference to the User s Manual of concerning device 3 1 2 4 Manual Set NG This message is indicated when a cut sheet paper is inserted to the Bypass Feeder during warming up Remove it from the Bypass Feeder 3 10 Chapter 3 Error Correction 3 1 2 5 Cutter Set NG This message is indicated when the Cutter Knob is not located at the correct position Open the Roll Deck and s
9. safely use this product These notes are important in preventing danger to the operator or operation of the printer The following symbols are found throughout the USER S Manual and have the following meaning WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction CAUTION This CAUTION mark means that there is a possibility of injury or physical damage if you ignore or do not follow the said instruction When marked with this symbol DO NOT ATTEMPT When marked with this symbol pay close attention to WARNING Ground the product with a correct ground source or you may be electrically shocked The Power source should be as follows In the USA 120V plus minus10 50 60Hz 15A or higher In Europe 220 240V plus6 or minus10 50 60Hz 10A or higher Use a circuit with a dedicated breaker Install the product as close to the wall outlet as possible If you wish to move the printer please contact your service personnel Do not remove the screw and do not open the cover if not instructed to do so in this User s Manual If you ignore this warning you may be burnt or receive an electric shock due to a hot item or electrically charged part inside of the printer Do not disassemble or tamper with the printer lt may result in a fire or an electrical shock Do not plug in the printer into a multi wire connector in whi
10. second Metric 3 3 ppm AO 5 6 ppm A1 Landscape Inch 5 8 ppm D Landscape Print head LED Array Resolution of print head Print width Maximum 914 mm 36 Minimum 297 mm or 11 roll media 210mm cut sheet Print length Maximum 6 000 mm for AO 36 wide plain paper or 5 x Standard length plain paper 2 x Standard length tracing paper 1 x Standard length film Option 24 000 mm Minimum 210 mm or 8 5 A NOTE If the print is longer than 6 000 mm its image quality or the reliability of paper feeding is not guaranteed Warm up time Shorter than 4 minutes 30 seconds At 23 C 60 RH the rated voltage and plain paper is used First print time 18 seconds D Landscape At 23 C 60 RH the rated voltage and plain paper is used Fusing method Heat and Pressure Rollers Development method Dry type non magnetic mono component toner Media Recommended Media Europe Asia model Plain Paper 64 g m to 80 g m Oce Red Label 75 g m Tracing Paper Oce Transparent Paper 80 g m Film Oce 3 5MIL US model Bond Paper 64 g m to 80 g m US Bond PB 20 Vellum US Vellum XV 20 Film 4MIL PF 4DDME Storage of consumables Toner cartridge Store the cartridge within the temperature range from O to 35 degrees Centigrade and within the humidity range from 35 to 85 RH NOTE The above specifications are subject to change without notice 1 6 Chapter 1 Before Use
11. 4 600dpi Print Head and optimum Image Process System realize the highest image quality 5 The print image is more stabilized by adoption of minute toner for mono component development 6 The combination of Contact Development System and mono component minute toner can produce a high definition line distinctive grayscale and consistent solid black 100 of toner can be used as this development system generates no Waste Toner 1 4 Chapter 1 Before Use 1 4 Specifications 1 4 1 General Specification CX 8048 Console 1 680 W Including Scanner amp Controller Unit Maximum Low power mode Acoustic noise Printing Impulse sound Machine noise emission regulation no 3 GPSGV The highest sound pressure level is 70 dB A or less in line with EN ISO 7779 Max 0 1 ppm Measurement method under UL Standard 1 266 mm Width x 600mm Depth x 1 107 mm Height UI is not included About 219 kg 1 roll About 232 kg 2 roll Environmental condition Temperature for usage 10 to 32 degrees Centigrade Humidity 15 to 85 RH Interface Network Interface 10 BASE T 100 BASE TX Input power In the US 120V plus minus 10 50 60Hz 12A In Europe 220 240V plus 6 or minus 10 50 60HZ 7A NOTE The above specifications are subject to change without notice 1 5 Chapter 1 Before Use 1 4 2 Printer part Subject Printing method Photoreceptor Organic Photoconductive Drum Print speed 80 mm per
12. OTE 1 Fully insert Flange into the roll media core so that the inside rim of Flange evenly touches the side face of the roll media Correct Fully inserted 2 Flange has Stoppers 6 with sharp edge Be sure not to touch them 2 6 Chapter 2 Basic Operation 5 Push both the levers 3 down in either way Position them flat against Flange to secure the roll media 5 in Roll Deck 1 Note the rewinding direction Rear Deck back Rear Deck back Front to Guide Plate Front to Guide Plate Correct Edge comes from bottom Wrong Edge comes from top continued on the next page 2 7 Chapter 2 Basic Operation NOTE 2 The outside rim 7 of Flange should meet the black triangle 8 marked on Slide Guide Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding Correct 7 Insert the leading edge of the roll media under Guide Plate 9 until it touches the feeding roller Rotate Feed Knob 10 clockwise so that the feeding rollers catch the leading edge Use the rear Feed Knob 11 for Roll Deck 2 2 8 Chapter 2 Basic Operation 8 Hold the green grip 12 on the middle of Guide Plate and turn Guide Plate outside With holding rotate Feed Knob 10 again so that the leading edge comes out in 100 mm Leading edge 9 Slide the green Cutter Knob 13 fully from one side to the other to make a new straight edge R
13. aper mis feed defective print image or paper creasing if you use paper that does not satisfy the specification 4 Do not use a paper of which surface is very special such as thermal paper art paper aluminum foil carbon paper and conductive paper 5 Do not use papers with unpacked exposed in high low temperature amp humidity in a long period Such papers may result in mis feed defective image or paper creasing 6 Tracing paper exposed to air over a long period tends to cause a defective printing Both loading a tracing roll paper to Deck 1 front and removing one round on its surface from the beginning are recommended Refer to 2 3 Roll Media Replacement on page 2 5 1 7 2 Keeping the paper in the custody Keep the paper in the custody taking care of the following matters Do not expose the paper to the direct sunlight Keep the paper away from high humidity It must be less than 70 Put the paper on a flat place If you will keep the paper in the custody which you have already unpacked put it into the polyethylene bag to avoid humidity RON 1 14 Chapter 1 Before Use 1 7 3 Treatment against environmental condition Take a necessary treatment according to the environmental condition as shown below Humidity Possible problem Necessary treatment Low Void of image crease of paper and 1 Install the humidifier in the room and other problems occurs when you print humidify the ro
14. ce Call Errors perator Call Errors zech sesch sesch sesch sesch wesch ch sesch ch sesch sesch sesch ee ee Paper mis feed error O E NN OE CONDOR ON DOOR WDND Deck Jam Feeding Jam Manual Jam Reg Jam Internal Jam Fuser Jam Accessory Jam Original Jam H H ef UR E re ee ee Deck open EE Accessory Error Manual Set NG Butler Ser NG rss Toner Empty KEE Paper Empty re ee arte iva tes E came nein The door opened during the print Chapter 3 Error Correction OOo eee eRe Ce SUC eee Ce seer eres rer rere cere rer rer racer errr er errr errr res rer rere errr rece e reece cree reser rrr cer rrr reser rec rer rr ere rrr res rer rece c rrr re reer reser reece rier rere reer rere ee 3 1 sesesecosososocososocosososososoceososooooosososososososososososo sessosooocososocososososososocososososososocososocosososoosoooeososoooooo Chapter 3 Error Correction 3 1 Operator Call Errors 3 1 1 Paper mis feed errors NOTE 1 Take care not to get paper cuts on your hand 2 Take off your ring bracelet or watch when clearing paper jam If they touch to internal components it may result in a burn an electric shock or damage to components 3 Gently remove a jammed paper When it does not reach Fuser Unit toner on it may spill off If toner gets into eyes or your mouth immediately rinse them with water and contact a doctor 4 Gently remove a jammed paper When it
15. ch some other equipment is plugged into lt may cause a fire due to outlet overheating Do not damage the Power Cord by stepping on or placing heavy items on it lf the Power Cord is damaged it may cause a fire or you may receive an electric shock REPLACE THE CORD IF DAMAGED Do not put a flower vase a flowerpot or any water filled item on the product Spilt water could cause a fire or an electric shock If the product generates an abnormal smell or noise turn it off and unplug it from the wall electrical outlet immediately Do not throw the toner into a fire or other sources of heat as it can explode CAUTION Do not install the printer in a humidified room or a dusty room Also do not install the printer on an unstable floor as injuries may occur 1 Unplug the printer before you move it The power cord may be damaged and it may result in a fire or electric shock If you do not use the printer for a long duration holidays company shutdown turn off and unplug the printer from the outlet for safety Do not pull the cord when you unplug the printer as you may damage the Power Cord There are hot items inside of the printer Take great care not to touch these items when you remove mis fed media Ventilate the room well if you print in a small area POWER CORD INSTRUCTION The installation of or exchange to a power plug which fits in the wall outlet of the installation location shall be conducted in accor
16. ction Chapter 4 Maintenance page 4 1 Cleaning EE 4 2 4 1 1 Scanner Od AU Rar urn 4 2 4 1 2 Print Engine EE 4 4 4 1 3 Touch Screen essen 4 6 4 1 Chapter 4 Maintenance 4 1 Cleaning 4 1 1 Scanner Unit Clean each Scan Glass Feeding Rollers and Guide Plates once per a week as the scan copy image may become defective if these parts are dirty 1 Turn off CX 8048 2 Open the Scanner Unit pulling up the Levers 1 3 Wipe each Scan Glass 2 Feeding Rollers 3 and the inside surface with a soft cloth Use equal volume mixture of water and a neutral detergent NOTE Do not use organic solvent glass cleaner and anti static spray for the cleaning 4 2 Chapter 4 Maintenance 4 Wipe both the Feed Rollers 4 and the inside surface with a soft dry cloth NOTE Press down Scanner Unit on both side to close it Do not close it by pressing only one side down 4 3 Chapter 4 Maintenance 4 1 2 Print Engine Clean each Guide Film and Guide Plate once per a week as the toner or paper dust may accumulates on such part which may result in a defective print image 1 Turn off CX 8048 2 Open the Engine Unit pulling up the Engine Unit Open Levers 1 3 Wipe Guide Plate 2 3 black rubber area with a soft dry cloth to remove toner or paper dust 4 4 Chapter 4 Maintenance NOTE 1 There is a Photoconductive Drum large green cylinder in the machine w
17. dance with the following IN WARNING Select a power plug which meets the following criteria The plug has a voltage and current rating appropriate for the product s rating marked on its name plate The plug meets regulatory requirements for the area The plug is provided with a grounding pin or terminal lf the appropriate plug does not fit the wall outlet in the installation the customer shall install an appropriate outlet Connector Type Standard Usually found in IEC60320 C13 10A 250V 15A 125V Usually foundin Plug Type Model Rating 220 240V Standard Usually found in 9 9 AS NZS 3112 10A 250V Australia New Zealand GB1002 10A 250V China GB2099 1 BS 1363 10A 250V United Kingdom SASO 2203 10A 250V Saudi Arabia BS 546A 15A 250V United Kingdom IS 1293 India SABS 1293 South Africa SEV 1011 10A 250V Switzerland Chapter 1 Before Use page 1 Installation Requirements Seege 1 2 2 Originals Prohibited from Duplication tet EE 1 3 _3 F atllires ame 1 4 4 Specifications eer 1 5 5 Appearance EE 1 7 1 5 1 Front view essen 1 8 1 5 2 Rear view essen 1 9 6 Specifications for the Scan Original Re 1 10 _7 Specifications for the Printing Paper ER 1 13 1 7 1 Papers not avallableTo use essen aah eee 1 13 1 7 2 Keeping the paper inthe custody ee 1 14 1 7 3 Treatment against environmental condilion Hesse 1 15 1 1 Chapter 1 Before Use 1 1 Installation Requirements The follo
18. does not reach Fuser Unit toner on it may spill off on your cloth Dust off your cloth Use cold water to wash in out Using hot water may leave a stain 5 If a paper jam occurs using multiple copy and set copy Jam Recovery screen will appear in the Ul Jam Recovery reprints the removed sheets Enter a number of the images to be reprinted Jam Recovery with the arrow buttons How many images would you like to reprint The available number ranges from 1 to 9 and the default is 2 GE ZE The number of images to be reprinted is T equivalent to the amount of the removed sheets Ge The number of images that have not been removed already printed or unprinted images should not be included Unprinted images not started yet because of the jam failure will be resumed on recovery of the machine Ex While making a 7 sheet set copy you remove sheets No 3 and 4 because of a jam gt The required number to be reprinted is 2 Jk LIL ss done ee SS S done removed unprinted waiting recovery 3 2 Chapter 3 Error Correction 3 1 1 1 Deck Jam Feeding Jam Either of Deck is jam or Feeding Jam will be indicated when the roll paper is mis fed in the Roll Deck 1 Open the Roll Deck and then rewind the roll paper 2 Insert the leading edge of roll paper under the Guide Plate 1 until the edge touches the feeding roller Then rotate the Paper Feeding Knob 2 clockwise
19. emove the cut portion NOTE Completely slide Cutter Knob 13 until it stops at either end Not doing so may cause a paper jam Correct 10 Close Roll Deck A NOTE Be sure to close the Roll Deck fully until it locks at the correct position A paper jam may occur if it is not locked firmly 2 9 Chapter 2 Basic Operation 2 4 Toner Cartridge Installation 1 Open the Toner Hatch 1 2 Slide the green Lever 2 to the right to unlock the Toner Cartridge Lever 2 is held automatically 2 10 Chapter 2 Basic Operation 3 Pressing down the Cartridge Lock Lever 3 turn the body 4 of cartridge to the arrow direction until it stops You can close the toner supply hole of the cartridge firmly by this treatment NOTE The toner may drop from the toner supply hole and it may scattered into the machine or on the floor if you remove the Toner Cartridge without closing the toner supply hole 5 4 Pressing down the Cartridge Lock Lever 3 bring up the left side of the Toner Cartridge first and then remove the whole cartridge from the machine 2 11 Chapter 2 Basic Operation 5 Shake the new Toner Cartridge several times left and right to make the toner smooth 6 Pressing down the Cartridge Lock Lever 3 fit the pin 6 on the left side of cartridge to the groove 7 on the machine side Please confirm that the Cartridge Lock Le
20. hich is right above the Guide Plate You will have to replace the Drum if it is damaged as it is a very important part in creating the print image Please take care of the following matters when you make cleaning a Do not touch the drum Adhering a fingermark or sebum on the Drum may cause defective printing b Take off such metal accessories as watch or ring You will have to replace the Drum if you damage the Drum scratching with such accessories c Do not leave the Upper Unit open for more than 10 minutes as the Drum is very sensitive to light Direct sunlight is very harmful Photoconductive Drum 7 2 Do not use water organic solvent and alcohol for the cleaning 4 Close the Engine Unit 4 5 Chapter 4 Maintenance 4 1 3 Touch Screen Clean the Touch Screen once a week 1 Wipe the Touch Screen with a dry cloth NOTE Do not use water alcohol organic solvent and glass cleaner for the cleaning 4 6 Chapter 4 Maintenance UTAX GmbH Ohechaussee 235 22848 Norderstedt Germany
21. ity to stop the power supply for Fuser Unit and some other components Sleep Mode is canceled and the machine gets ready when e the machine receives a print job through the network e the Ul is touched and an original is inserted into the scanner NOTE 1 It may take time for the machine to get ready 2 Touching the Ul can cancel the screensaver but cannot cancel Sleep Mode It may need another waiting time to start warming up for copying printing 2 17 Chapter 2 Basic Operation 2 9 Dehumidifying Roll Media lf the roll paper is extremely humidified it may cause several kinds of defective print Defective prints you will experience most will be crease of paper and loss of image Normal Print Crease of paper If the media is humidified gt Normal Print Loss of image If the media is humidified gt Turn on the Dehumidify Heater if the room air has too much humidity 65 or higher to prevent the above kinds of print defect You may be able to fix the above kinds of problem NOTE CX 8048 is equipped with the Dehumidify Heater optional for the US lf needed contact the service personnel for detail To turn on the Dehumidify Heater press the H side of the Dehumidify Heater Switch on the rear Press its L side to turn off Dehumidify Heater Switch 2 18 Chapter 2 Basic Operation 3 1 3 1 3 1 3 2 OWWWWWWWYWWWWWW LD Servi
22. lide the Cutter Knob fully to the left or right to align the Cutter Knob with the end of the railing Incorrect Not placed at the end Correct Placed at the left or right end NY Cutter Knob 3 1 2 6 Toner Empty This message is indicated when the Toner Cartridge is emptied with the toner Replace the Toner Cartridge with the new one making reference to 2 4 Toner Cartridge Installation on the page 2 10 3 1 2 7 Paper Empty This message Is indicated when the roll paper in use is emptied Replace roll paper with the new one making reference to 2 3 Roll Media Replacement on the page 2 5 3 1 2 8 The door opened during the print This message is indicated when the Roll Deck is opened during printing by accident Close the Roll Deck If the paper is mis fed inside the machine remove it 3 11 Chapter 3 Error Correction 3 2 Service Call Errors In case the following Error Codes for a serious failure appear in the screen PLEASE CALL YOUR TRAINED SERVICE PERSONNEL TO RESOLVE THE ERRORS No operation should be done by the customer E 003 Temp Not Rise E 080 Cosi Density Sensor Error If any of the above errors appear 1 Turn off CX 8048 and turn it on after an interval of 30 seconds or more 2 If the same error code appears turn off CX 8048 and then unplug the printer from the wall outlet after an interval of two minutes for shutdown Call your service personnel 3 12 Chapter 3 Error Corre
23. n is shown with available options 4 When the Ready Indicator stops flashing the CX 8048 is ready for operation You can make a copy scan optional or print optional 2 3 Chapter 2 Basic Operation 2 2 Turning off CX 8048 1 There is a Power Switch on the right side of CX 8048 Press its CY side to turn off the CX 8048 Power Switch Press y side A CAUTION The CX 8048 print engine and UI appear to be shut down when you turn off CX 8048 However the controller PC embedded inside the CX 8048 is still operating and will shutdown in approximately two minutes after Power Switch operation Do not unplug the CX 8048 before the controller PC completes its shutdown Doing so may damage data or the device 2 4 Chapter 2 Basic Operation 2 3 Roll Media Replacement NOTE 1 A paper mis feed tends to occur just before out of a roll paper 2 A tracing roll paper is recommended to be loaded to Roll Deck 1 front Reference This section describes how to install a roll media to Roll Deck 1 The same procedure is applied to Roll Deck 2 unless otherwise noted 1 Open Roll Deck 1 and remove an empty roll core 2 3 Move a right Slide Guide 5 to match your roll media s width The right and left Side Guides will automatically move together 2 5 Chapter 2 Basic Operation 4 Insert each Flange 4 into both ends of the roll media core to be installed N
24. om air with plain paper and tracing paper 2 Remove the paper from the machine right after the completion of print and keep it in a polyethylene bag Void of image occurs when you print If you will not make print soon remove with tracing paper the tracing paper from the machine and keep it in a polyethylene bag 40 Remove the paper from the machine after everyday use and keep it ina polyethylene bag 10 Void of image occurs when you print If you will not make print soon remove with plain paper and tracing paper the tracing paper from the machine and keep it in a polyethylene bag Void of image crease of paper and 1 Turn on the Dehumidify Heater if other problems occurs when you print installed with plain paper and tracing paper 2 Remove the paper from the machine right after the completion of print and High keep it in a polyethylene bag NOTE 1 CX 8048 is equipped with the Dehumidify Heater optional for the US Using it in high humidity environment 65 or higher is recommended Refer to 2 9 Dehumidifying Roll Media on page 2 18 2 Void of image and crease of paper will occur in case of extremely high or low humidity Normal Print Crease of paper If the media is humidified If the media is humidified 2 1 15 Chapter 1 Before Use Chapter 2 Basic Operation page TORING ON CX8048 sefa e OD TUFNING OM ER IT SE 2
25. rding to the original width 2 Place the original on the Original Table with face up Then insert it under the Scanner Unit along with Original Guides When the leading edge touches the original feeding roller the machine automatically carries and sets the original at the proper position 3 The CX 8048 will start the print process NOTE The scanner unit does not accept originals automatically during Sleep Mode Touch any area in the touch screen and then insert an original 2 15 Chapter 2 Basic Operation 2 7 Emergency Stop of Scan or Copy If necessary press the Emergency Stop Button 1 on the Scanner Unit to immediately stop the original while making a copy or scan Pressing the button stops the current reading a document immediately The current printing is stopped as well and is ejected u SEN Stop on the touch screen will work as the same function JOB INE NOTE Do not pull back or hold down the original on Original Table as an attempt to stop feeding it through Scanner Unit 2 16 Chapter 2 Basic Operation 2 8 Canceling Sleep Mode The CX 8048 has two Sleep Modes to reduce the power consumption The CX 8048 will enter Sleep Mode after a certain period of inactivity In the default setting e Warm Sleep Mode will start after a 15 minute of inactivity in order to reduce the power supply for Fuser Unit e Cold Sleep Mode will start after a 60 minute of inactiv
26. so that the feeding rollers catch the roll paper The leading edge should be trimmed with a cutter in case of an extreme crease For Roll 2 use the Paper Feeding Knob on the rear side 3 3 3 Chapter 3 Error Correction 3 When the feeding rollers catch the paper turn the middle of the Guide Plate 6 4 outside Rotate the Paper Feeding Knob 2 again until the leading edge comes out in 100 millimetres Leading edge 4 Slide the green Cutter Knob 5 one side to another completely to make a new straight edge Remove the cut portion NOTE Completely slide Cutter Knob 5 until it stops at either end Not doing so may cause a paper jam Correct Cutter Knob at end Wrong Cutter Knob at middle 5 Close Roll Deck NOTE Be sure to close the Roll Deck fully until it locks at the correct position A paper jam may occur if it is not locked firmly 3 4 Chapter 3 Error Correction 3 1 1 2 Manual Jam 1 Pull up the Engine Unit Open Levers 1 to open the Engine Unit Do not open the Engine Unit when the Scanner Unit is opened If the Scanner Unit is opened it will hit the bottom of User Interface 2 Remove the mis fed paper pulling frontward 3 Close Engine Unit NOTE 1 Be sure to close the Engine Unit firmly until it is locked at the correct position 2 The mis fed paper can be replaced with a new one or be inser
27. ted at the opposite edge to the feeder An extreme crease may cause a paper jam 3 5 Chapter 3 Error Correction 3 1 1 3 Reg Jam Internal Jam 1 Pull up the Engine Unit Open Levers 1 to open the Engine Unit Do not open the Engine Unit when the Scanner Unit is opened If the Scanner Unit is opened it will hit the bottom of User Interface 2 Remove the mis fed paper 3 Close the Engine Unit firmly NOTE Be sure to close the Engine Unit firmly until it is locked at the correct position 3 6 Chapter 3 Error Correction 3 1 1 4 Fuser Jam 1 Pull up the Engine Unit Open Levers 1 to open the Engine Unit NOTE Do not open the Engine Unit when the Scanner Unit is opened If the Scanner Unit is opened it will hit the bottom of User Interface 2 Remove the mis fed paper if you find it Go to the later step 4 when the mis fed paper cannot be seen or removed 3 Close the Engine Unit firmly NOTE Be sure to close the Engine Unit firmly until it is locked at the correct position 3 7 Chapter 3 Error Correction 4 Open the Exit Cover 2 Remove the jammed paper pulling to the rear side A WARNING There are extremely hot parts inside the Exit Cover Do not touch any parts in the Heater Unit or you will be burnt Also be careful not to get burnt when you touch the printing paper as it may be very hot NOTE lf removed a
28. trength must be ample to sustain the weight of the equipment Y 60cm or wider When Tray is installed Rear side er u 45cm or Y wider E CX 8048 Front side 70cm or wider 1 Roll Deck 90cm or wider 2 Roll Decks 1 2 Chapter 1 Before Use 1 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original You may be punished by the law if only you possess the copy of some kind of original We recommend you to consider enough before you copy such original Originals prohibited from copying by the law 1 It is not allowed to copy Currency Bill Money Bank Note etc Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc 2 It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments 3 It is not allowed to copy unused postal stamps or government postcards without permission to make replica from Government 4 It is not allowed to copy Government issued revenue stamps certificate stamps which are prescribed by Liquor Tax Act or the Commodity Tax Act Special items to be cared 1 It is warned by the government to copy private issued securities stock certificate draft check goods ticket etc commutation ticket or book of tickets excluding that some specific company copies such originals as many as it requires for its own business 2 We recommend you not to copy freely such originals as government issued passport
29. ver 3 firmly locks the Toner Cartridge at the correct position It must be at a level position Good No good 2 12 Chapter 2 Basic Operation 7 Turn the body 4 of the cartridge in one revolution to the arrow direction to open the toner supply hole Confirm that the projection 8 if fitted into the notch 9 NOTE It is not necessary to lock the cartridge with the Lever 2 Lever 2 will engage on its own after closing the Toner Hatch 8 Close the Toner Hatch 1 2 13 Chapter 2 Basic Operation 2 5 Cut Sheet Media Placement 1 Open the Bypass Feeder 1 2 There are several size markings on the table of Bypass Feeder which indicate possible feed positions Place the cut sheet paper on the table between its concerning size markings then insert it into the Bypass Feeder When the leading edge touches the feeding roller the machine automatically carries and sets the paper at the proper position NOTE As a curly cut sheet will cause a mis feed straighten the sheet as far as possible before printing And set the sheet in curl down direction as a mis feed can be avoided Curl up sheets tend to result in a mis feed Correct curl down Incorrect curl up 2 14 Chapter 2 Basic Operation 2 6 Copying 1 There are several size markings on Original Table which indicate possible feed positions Line up Original Guides 1 with the proper markings acco
30. wing conditions are required for installation of the equipment Q 1 Power source should be rated as follows In U S A 120V plus minus 10 50 60Hz 15A or higher In Europe 220 240V plus6 or minus10 50 60Hz 10A or higher 2 The equipment must be on an exclusive circuit 3 The outlet must be near the equipment and easily accessible 1 Make sure to connect this equipment to a grounded outlet 2 For PLUGGABLE EQUIPMENT the socket outlet shall be installed near the equipment and shall be easily accessible The site temperature range 10 to 32 degrees Centigrade with the humidity between 15 to 85 RH NON CONDENSING Keep the printer away from water sources boilers humidifiers or refrigerators 1 The installation site must not have open flames dust or ammonia gases 2 The equipment must not be exposed to the air vents from air conditioners It may affect the image quality 3 The equipment should not be exposed to the direct sunlight Please draw curtains to block any sunlight When you open the Movable Unit do not expose the Photoconductive Drum to strong intense light as this will damage the Drum Ozone will be generated while this equipment is use although the quantity generated is within safe levels see certifications Ventilate the room if required Keep ample room around the equipment to ensure comfortable operation Refer to the following figure The equipment must be leveled and the floor s
Download Pdf Manuals
Related Search