Oxygen Regulator User Manual
Contents
1. sessssssee eee 4 Classifications eere 5 SDECIBCALIOBS LL orssrrbrpkPPEEPPEPEEEETERPRDEREEPEDEPEREEE 6 Installation and Operation 7 Cleaning 2 FRANE aa 9 Accessories and Spare Parts 10 MaTncenanc uod od OUR OR E RARE 11 Troubleshooting eeeeeeeeesee 12 Warranty MEME 14 CLEMENTS CAUTION PLEASE READ THOROUGHLY AND FOLLOW DIRECTIONS CAREFULLY BEFORE OPERATING EQUIPMENT WARNING OXYGEN IS A NON FLAMMABLE GAS IT WILL HOWEVER SUBSTANTIALLY INCREASE THE RATE AT WHICH FLAMMABLE MATERIALS BURN OIL GREASE AND OTHER HYDROCARBONS WHEN COMBINED WITH OXYGEN WILL BECOME HIGHLY COMBUSTIBLE AND SHOULD NEVER BE USED ON ANY PART OF THE OXYGEN CYLINDER REGULATOR OR OTHER EQUIPMENT USED WITH OXYGEN GENERAL SAFETY INFORMATION l No SMOKING Remove matches lighters lighter fluid and other flammable materials from the oxygen therapy area before administering oxygen Inspect the oxygen cylinder valve regulator and flowmeter thoroughly for dust oil and grease Do NoT USE THE OXYGEN REGULATOR IF OIL OR GREASE IS PRESENT Inform your gas supplier of this condition immediately If using a humidifier or similar device remove the device from the regulator before changing the cylinder Do NOT ALLOW FLUIDS TO ENTER REGULATOR In any situation requiring emergency oxygen call a physician or emergency medical service clinician immedi2. Oylinder valve Pressure gauge Blockage in regulator Replace cylinder Confirm turned on Replace Replace regulator Seal washer present and in good condition Debris on valve seat Tee handle secure Replace seal washer Clean Tighten Outlet pressure incorrect Cylinder valve Confirm pressure with calibrated gauge Confirm turned on Replace regulator No Flow Service Self sealing valve Blockage in regulator Inlet filter blocked Replace regulator Replace regulator Replace inlet filter Apart from the sealing washer Bodok Seal there are no user serviceable parts on the oxygen regulator Refer all service to suitably qualified and authorised personnel Troubleshooting 11 CLEMENTS Exploded View k OE CON art uk a Exploded View CLEMENTS Part List Item Description 1 Body 2 Yoke Connector 3 Safety Relief Body 4 Safety Relief Seat 5 Seat Retainer 6 Relief Spring 7 Cap 8 Spring 9 Seat Assembly 10 Orifice 11 Retainer 12 Diaphragm 13 Diaphragm Plate 14 Nut 15 Gasket 16 Adjusting Spring 17 Spring Seat 18 Cover 19 Label 20 Adjusting Screw 21 Cap 22 Outlet Nipple 23 Lock Nut 24 Outlet Nut 25 Gauge Parts List 13 CLEMENTS 14 Warranty BMDi TUTA Healthcare Pty Ltd warrants that this product is free from defects in workmanship and materials for a period of 12 months from the date of sh
3. cylinder valve regulator and flowmeter thoroughly for dust oil and grease Do NoT USE THE OXYGEN CYLINDER IF OIL OR GREASE IS PRESENT Inform your gas supplier of this condition immediately With the cylinder valve outlet facing away from you slightly open the oxygen cylinder post valve to purge any debris from the valve seat then re close the valve Slip the yoke over the cylinder post valve and fit the yoke pins into the holes in the cylinder valve The pins should fit easily into their respective holes Do not force the pins into the holes Ensure that the sealing washer is in place on the regulator yoke connection and is in good condition Ensure the Tee Handle screw point is seated on the dimple on the cylinder post valve Turn the Tee handle clockwise and tighten until secure to provide a leak proof connection Connect Flowmeter to Regulator l Attach flowmeter to the regulator and tighten connector If the flowmeter is a tube style unit ensure that the tube is maintained in a vertical tube up position Ensure that the flowmeter is off turn flow control knob clockwise Pressurise the Regulator l 2 Slowly open the cylinder post valve Confirm that the cylinder pressure gauge indicates adequate capacity A cylinder with less than 2MPa should be exchanged for a full cylinder to ensure an adequate supply of oxygen Confirm that there are no leaks in the oxygen cylinder regulator and flowmeter circuit Instal
4. loss or damages in any way as a result of the use of the product The warranty does not extend to cover damage to the following parts as they are inherently prone to wear e motor brushes This warranty does not extend to cover corrosion due to any cause nor to any damage to painted or anodised surfaces BMDi TUTA Healthcare will give the purchaser the benefit of any manufacturers warranty in respect of any components in the product which were not manufactured by BMDi TUTA Healthcare if such a manufacturer s warranty is available Warranty i5
5. CLEMENTS ANA 74300 Oxygen Regulator with Yoke Connector S O N t L i9 qe i ae NY J ie i L TE C i 2 O x oO User Manual Manual No ANA 74300 001 Issue 1 CLEMENTS Safety Thank you for purchasing this Clements Oxygen Regulator For your safety it is imperative that this unit only be operated by authorised personnel in accordance with the instructions as described in this manual Operated in this way the Oxygen Regulator will provide the standard of service specified Due to continual improvements in product design the Oxygen Regulator may vary in detail from the descriptions in this manual In the event of further questions please contact your local distributor or BMDi TUTA Healthcare direct ad Morris Engineering Works Ltd 43 Kung Yeh Road Kuan Tien Industrial District Tainan Hsien Taiwan Republic of China User Manual Oxygen Regulator Manual Number ANA 74300 001 Issue 1 Copyright 2010 BMDi TUTA Healthcare Pty Ltd The information in this manual was originated by and is the exclusive property of BMDi TUTA Healthcare Pty Ltd It is furnished for customer information only and is not an authorisation or licence to make this product or to furnish this information to others BMDi TUTA Healthcare Pty Ltd Level 17 275 Alfred St North Sydney NSW 2060 Australia Phone 61 2 9466 5300 Fax 61 2 9922 7165 Website www medaust com CLEMENTS Contents Cautions
6. S Cleaning WARNING DO NOT USE ANY OIL BASED OR HYDROCARBON PRODUCTS ON THIS OXYGEN REGULATOR Cleaning Clean using a pH neutral disinfectant for wiping clean Wipe with a damp cloth and dry with paper towel to remove residue Do not wipe the contact areas of the inlet and outlet connectors Transportation and Storage Environmental conditions for transportation and storage are shown in the following table Parameter Minimum Maximum Temperature 10 C 40 C Humidity 60 RH 95 RH Barometric Pressure 700 mBar 1060 mBar Cleaning CLEMENTS Accessories and Spare Parts ANA 74300 001 User manual for Oxygen Regulator ANA 74100 Oxygen Flowmeter 0 15 litre min ANA 74100 100 Humidifier for Oxygen Flowmeter ANA 74300 201 Kit Gauge for Oxygen Regulator ANA 74300 202 Kit Yoke for Oxygen Regulator ANA 74300 203 Kit Bodok Seal for Oxygen Regulator 10 ANA 74300 204 Kit Inlet Filter for Oxygen Regulator 5 ANA 74300 205 Kit Service Spring for Oxygen Regulator ANA 74300 206 Kit Service Seal Seat for Oxygen Regulator Maintenance Period Check Action Each Use Visible Damage Repair replace Leaks Repair replace Gauge Accuracy Repair replace Outlet Pressure Replace Yoke seal washer Replace 19 Accessories and Spares Troubleshooting Fault Check CLEMENTS Rectify No reading on pressure gauge Oylinder
7. ately This unit is an inhaler and is useful only on persons who are breathing prior to administering oxygen Safety Information CLEMENTS Intended Use Regulate the high pressure from an oxygen gas cylinder to a lower constant pressure for use with oxygen therapy equipment Classifications GMDN 35300 Regulator gas high pressure Classification Class llb ARTG 174010 Clasifications CLEMENTS Specifications Gas Medical Oxygen Maximum Inlet Pressure 20MPa 2900psi Outlet Pressure 400kPa 58psi Regulator Fixed output pressure diaphragm style Inlet Connector Type pin indexed yoke CGA 870 AS 2473 3 2007 Outlet Connector Oxygen ring index AS 2896 1998 Safety Pressure safety valve ball and seat type Gauge 50mm kPa and colour coded capacity band Gauge Range 0 to 20 000 kPa graduated at 1 000 kPa Duty Cycle Continuous operation Standard AS 3840 1 1998 Unit 170W x 135H x 90D Pimansrans Packed 205W x 160 H x 165D Weight Unit 1 08kg Packed 1 3kg Ambient Temperature 189C to 60 C Standard Conditions 25 C Sea Level 101kPa Installation and Operation Check for Damage Carefully examine the oxygen regulator for any visual signs of damage that might have occurred during shipment Specifications CLEMENTS Installation and Operation Connect Regulator to Cylinder l Inspect the oxygen
8. ipment by BMDi TUTA Healthcare or its authorised agent to the purchaser Subject to the conditions of this warranty if the product fails to operate for any reason within the warranty period and the product is returned to the place of purchase at the purchaser s expense BMDi TUTA Healthcare will repair or replace the product free of charge If a valid warranty claim is made within 30 days from the date of shipment then BMDi TUTA Healthcare will also reimburse the purchaser for reasonable freight costs in returning the product to the place of purchase Conditions of Warranty 1 The product must be returned to the place of purchase with proof of purchase 2 This warranty is only available to the original purchaser of the product 3 The product must not have had its serial number removed defaced or changed its casing opened its power supply altered or have been tampered with in any other way 4 This warranty does not cover inadequate or incorrect site preparation improper installation connection to the wrong voltage failure of the product due to misuse ethe use or operation of the product outside of the physical electrical or environmental specifications of the product euse in a manner or environment in which the product is not designed to be used improper adjustment calibration or operation by the purchaser ethe use of accessories including consumables hardware or software which were not manufactured
9. lation and Operation CLEMENTS Adjust the Oxygen Flow l Turn the flowmeter control knob anti clockwise until the centre of the ball corresponds with the line indicating the required flow rate 2 When finished administering oxygen therapy turn the flowmeter control knob clockwise to the off position Confirm that the ball indicates zero WARNING Do not use high concentrations of oxygen for more than 5 hours without 1 hour interruptions Closing the Regulator If the regulator will be used again in a short time one hour or less turn the flowmeter control knob clockwise to off If the regulator will not be used for a longer period of time turn the cylinder valve clockwise to the OFF position Removing the Regulator from a Cylinder 1 Turn the cylinder valve clockwise to the OFF position 2 Open the flowmeter control knob to bleed the residual pressure from the circuit Allow the gas pressure in the regulator circuit to completely escape The flowmeter and pressure gauge should both indicate zero 3 Close the flowmeter control knob 4 If using a humidifier or similar device remove the device from the regulator flowmeter before changing the cylinder Do not allow fluid to enter 5 Turn the Tee handle anti clockwise to allow pins to disengage from post Remove regulator from cylinder WARNING Never attempt to remove a regulator from a cylinder if the pressure gauge shows pressure Installation and Operation CLEMENT
10. or approved in writing by BMDi TUTA Healthcare Warranty 10 11 12 13 CLEMENTS any modifications of the product which were not authorised in writing by BMDi TUTA Healthcare eany contamination or leakages caused or induced by the purchaser and inadequate or improper maintenance of the product This warranty does not cover normal wear and tear BMDi TUTA Healthcare will not be responsible for damage or loss caused during shipping In Australia apart from any warranties implied by the Trade Practices Act 1974 all other warranties expressed or implied and whether arising by virtue of statute or otherwise are hereby excluded Outside Australia all other warranties expressed or implied and whether arising by virtue of statute or otherwise including any warranties implied by the Vienna Convention are hereby excluded BMDi TUTA Healthcare s obligations under this warranty are limited to the repair or replacement of the product within the terms of this warranty and the total liability of BMDi TUTA Healthcare for loss or damage of any kind whether arising pursuant to the terms of the sale of the product or otherwise in connection with the product is limited to the amount paid by the purchaser to BMDi TUTA Healthcare for the product Apart from any liability imposed by Part VA of the Trade Practices Act BMDi TUTA Healthcare accepts no other liability for any loss or damage occasioned including consequential
Download Pdf Manuals
Related Search