M28Z Table User Manual
Contents
1. Upgrade directory The files should be in the format ARMxxxx Bin and FPGAxxxx Bin The xxxx shows the version number 3 To enter the Firmware Upgrade Function power up the system with the front panel Zoom Up and Zoom Down arrow keys pressed 4 The system will make a long sound upon entry to the Firmware Upgrade Function 5 The light will flash on and off and a beeping sound will be emitted until a USB Flash Drive is detected If no drove is detected the system will timeout after approx 30 seconds and boot normally 6 If you want to exit the Firmware Upgrade function simply power cycle the system by pressing the Power Button 7 When the USB Flash Drive is detected a The Firmware Upgrade Function searches the Upgrade directory for the 1st file with the name format ARMxxxx Bin and upgrades the ARM processor b The Firmware Upgrade Function then searches for the 1st file with the name format FPGAxxxx Bin and upgrades the FPGA Firmware 8 NB The Firmware Upgrade Function will use the 1st file with the correct name format it finds Therefore it is recommended that you only have the firmware version that you want to install in the Upgrade directory and not multiple versions 9 During the upgrade process beeping sounds will be emitted indicating progress 10 When the upgrade is complete the system will automatically restart with the new version Important If the USB Flash drive is2. Stamp the captured images Page 8 Modus 282 Table English Rev 1 Date xx xx xxxx Enter the current date starting with day month and then the year Note Time and Date are only used to Date Stamp the captured images Rev Displays the revision of the system This may required for support issues External Keypad control of Main Menu If you are using the optional external keypad 1 it s Zoom Up and Zoom Down buttons can be used instead of the Up and Down arrow on the front keypad The external keypad Focus key can be used instead of the Capture button on the front panel The Capture button can be used to Exit the menu Changing the Camera Macro Lens The Modus M28Z is shipped with a 52mm lens with a focal length of 250 mm 4 Dioptre It is threaded into the camera using an adaptor which has a 46mm thread size on one side anda 52mm on the other side The lens can be replaced by 52mm lens using the existing adaptor or by a 46mm lens which requires removing the adaptor and threading directly to the camera Note that a lens with a decreased focal length may require the Modus M28Z to be adjusted lower to remain within focal range and vice versa for a higher focal length lens Page 9 Modus 282 Table English Rev 1 Troubleshooting Changing the Output Frame Rate Most monitors and HD televisions can display the many different standards of HD signals however some cannot If your monitor T
3. removed during the upgrade process or has a corrupt file the system will not start and the upgrade process will have to be repeated Page 11 Modus 282 Table English Rev 1 Specifications Camera Resolution HD 1080p 1980x1080 at 50 60 Hz Monitor Connections HDMI DVI Monitor Requirements HD Ready or Full HD Recommended Outputs DVI HDMI TMDS Magnification 4 Lens 2x 85x 24 Monitor Image Capture USB 2 0 High speed Dimensions Table 24cm x 41cm Folded Height 11cm Raised Height 42cm Power 8 Watts Weight 2 5Kg Operating Temperature Storage 10 C to 60 C Operating 5 C to 40 C As we strive to constantly improve our products this information is subject to change without notice Declaration of Conformity We DeltaPix declare under our sole responsibility that this product Modus M28Z of the brand DeltaPix to which this declaration relates is in conformity with the following standards or other normative documents EN 60601 1 2 2007 Medical Electrical Equipment Electromagnetic Compatibility Classification Residential Following the provisions of EMC directive 2004 108 EC Signed for and on behalf of DeltaPix Alan Johnston Naas Ireland December 2011 Page 12 Modus 282 Table English Rev 1 Warranty DeltaPix warrants the equipment when purchased new to be free from defects in material and workmanship and wi
4. InfraRed On Normally the system filters out Infrared light Turning the Infrared On allows this spectrum of light to pass through to the camera When the Infrared mode is turned on the image becomes black and white WDR Off WD VE The Wide Dynamic Range mode is a function for dividing an image into several blocks and correcting blocked up shadows and blown out highlights in accordance with the intensity difference It enables you to view images with large intensity differences WD Images with Wide Dynamic Range are re produced by combining long exposure signals with high intensity signals obtained with short exposure VE Using the Visibility Enhancer function will make the darker part of a camera image brighter as well as automatically correct brightness and contrast to show parts clearly without overexposure Pick the option which shows the best results in your application Noise 0 5 The Noise Reduction function removes noise to provide clearer images Screen Size 7 100 Enter the size of your display in inches Measured Diagonally This size is used to calculate the magnification levels Lense Diopter 1 15 Enter the Lense Diopter number of the lense used Show OSD On Off Turning the OSD Screen Display OSD off removes all the static messages from the screen Time xx xx Enter the current time starting with minutes and then hours Note Time and Date are only used to Date
5. Modus 284 Table version DeltaPix Discover the Details User Manual Table of Contents Package COMI rs eee deci ate 3 HAS TAN AU ON 4 B ret nee rtd etter eestor ante Dee vem ee 4 Height 4 5 FOOL SWIC 5 CONTOR a 5 OWN bed ethane calcutta ted 5 5 6 Magnification level 050 6 ONT VIG W esse a a 6 6 Facon Cel UNS chee Soar EN 6 Main Men Controls scet ar 7 The following menu options are 7 External Keypad control of Main 9 TFOUDIESNOOUUNG 5 a E 10 Changing the Output Frame Rate 10 Taking Care of your Modus 284 10 Firmware Upgrade er tee era 11 SDECIICAUONS 12 Declaration of 12 Waranty 13 2 Modus M28Z Table English Rev 1 Package Contents Your Modus M28Z package contains M
6. The current magnification level is displayed for example 30 to show a magnification level of 30 When the magnification changes from optical to digital zoom a is also displayed x60d to indicate a magnification level of 60 and in digital zoom Overview Overview allows you to easily locate a point of interest on the object you are viewing Press and release the Overview button to make the camera zoom out fully and revert to full colour mode A cross is displayed in the centre of the screen as an aid to location Place the point of interest under the cross and press any key to restore the magnification to the previous level Brightness The image brightness can be adjusted to suit your preference Brightness adjustment is available by pressing and holding the Capture button you should hear a beep Next use the Zoom Up and Zoom Down buttons to adjust the image brightness as desired Press the Capture button again to save the setting and exit edit mode The setting you choose will be saved and used subsequently for that mode of operation Factory defaults Press Capture while powering on the Modus M28Z to restore factory settings for sound lighting brightness settings and video frame rate The factory default settings are lights on sound on and the frame rate that was set for your country before shipping Page 6 Modus 282 Table English Rev 1 Main Menu Controls e To access the Main Menu press and hold the Overview butto
7. V does not display the image from the Modus M28Z you should try the following Power off the Modus M28Z press and hold the Overview button and power on the unit This will change the unit from 50 Hz mode to 60 Hz or vice versa You will hear a sequence of beeps confirming the frequency change Taking Care of your Modus M28Z Do not touch the lens Dirt on the lens will appear as a blurred or dim image or as fuzzy spots on the screen If you believe the lens is dirty it can be cleaned with a soft dry cloth applying minimal pressure As the lens is polished and coated do not use a wet or coarse cloth avoid detergents and abrasive substances or solvents to clean it WARNING Never look directly at the LED light source for any prolonged period of time If the hinges loosen with use they can be tightened with the Allen key provided To do this insert the Allen key into the screw head Turn each screw clockwise about a quarter turn Do not over tighten Use only the supplied power supply and inspect the cabling regularly for damage Page 10 Modus 282 Table English Rev 1 Firmware Upgrade The Modus M28Z includes a Firmware Upgrade Function allowing end users to install new versions of the firmware which includes new feature additions and bug fixes 1 Make directory called Upgrade in the USB Flash Drive If the directory already exists then delete all the files from that directory 2 Copy the two upgrade files to this
8. ll repair or replace at DeltaPix discretion any equipment which exhibits such defects provided that the equipment has been operated under the proper conditions of installation and has not been tampered with by any persons not authorised by DeltaPix or its agents and that it is solely serviced by DeltaPix or its agents In no event shall DeltaPix or its agents be liable for special indirect incidental or consequential damages the original user s remedies being limited to repair or replacement This warranty is valid only when serviced in the country of original purchase DeltaPix makes no other or further warranty express or implied including and warranty of fitness for a specific purpose or warranty of merchantability This warranty is valid for a period of 12 Months effective from the date of delivery For warranty claims or service during or after warranty period please contact your distributor Delta taP x Discover the Details DeltaPix Aps Maalov Byvej 229 DK 2760 Maalov Denmark Phone 45 4676 0205 Fax 45 4464 3429 Page 13 Modus M28Z Table English Rev 1
9. n for seconds e The Menu will appear on the top of the screen including the menu navigational controls e Exit the menu at any time simply press the overview button The following menu options are available Sound On Off Enable or disable the system sound Light On Off Enable or disable the LED Lighting Crosshair On Off Enable or Disable the two artificially generated lines that appear on the screen in both the horizontal and vertical directions which intersect at the centre of the screen Crosshair Long Short Select the Crosshair size Short or Long Cross Col White Green Blue Red Yellow Purple Cyan Select the crosshair colour Bright Levels 0 14 The image brightness can be adjusted to suit your preference White Bal On Off White balance refers to the process of making sure whites appear as white in your images This will help eliminate colour casts that come from various light sources the sun incandescent bulbs and florescent bulbs Put a white object under the camera Half the image minimum and turn the white balance on To re balance later turn the white balance off and on again Note The White Balance Data is lost when the unit is powered down Focus Lock On Off Page 7 Modus M28Z Table English Rev 1 Turning the Focus Lock On will turn off the autofocus facility and lock the focus at the current setting Turning the Focus Lock Off will re enable autofocus
10. odus M28Z Camera and Table Power Supply HDMI to HDMI Cable Operation Manual Grounding Cable USB Memory Stick O O O O OBO Optional a External Keypad KP1 a Foot Switch Please retain the packaging in case there 15 a need to return the unit for service or repair Page 3 Modus 282 Table English Rev 1 Installation Cabling Plug the power supply into a mains socket Plug the power lead from the power supply into the Modus M28Z at the rear of the unit as shown below Plug the HDMI cable into the Modus M28Z and the other end into your HDMI compatible monitor Plug the external keypad optional into the Mini Din socket Plug the footswitch optional into the footswitch jack at the base of the unit Modus M28Z Table side view Modus M28Z Table rear view Height Adjustment Manoeuvre the camera head to the correct height above the table dictated by the focal length of the Lens used Lock the position by tightening the two knobs at the side of the unit Page 4 Modus 282 Table English Rev 1 4 Lens requires a distance of around 250mm between lens and table 5 Lens requires a distance of around 200mm between lens and table Light Adjustment The light can be rotated as shown It should be adjusted so that it shines on an area centred about the camera s image Foot Switch A footswitch is available for the Modus M28Z Table This allows control of the zoom functions The left pedal will zoom and
11. the right will zoom out This is useful for hands free operation of the zoom function To use the footswitch simply plug the jack into the footswitch socket at the bottom rear of the unit See diagram on previous page for location of foot switch socket Controls Power Push the power button to turn the unit on A blue image will appear on your screen and after a few seconds the picture from the camera will appear If not use your monitor s remote control or control panel to switch to the appropriate input used for the Modus M28Z Pushing the Power button again will power off the Modus M28Z Capture e use this feature insert a USB Key into the USB port e When the system has detected the key it will report USB Key Ready Page 5 Modus M28Z Table English Rev 1 When you have an image you want to capture simply press the capture button The system will indicate the image is being saved to the drive and when done The image is saved as a 1920 x 1080 bitmap BMP format The image name is Date and Time stamped and saved in this format IMG DateTime bmp Remove the USB Key and use a PC to view the saved images NB The USB Key must be in FAT File System Format It will not work with any other format Magnification Press the Zoom Up button to enlarge the image and Zoom Down to reduce the image size The unit will make a sound to indicate when it has reached maximum or minimum zoom limits Magnification level OSD
Download Pdf Manuals
Related Search