S800 User Manual en
Contents
1. means clock wise and means counter clock wise If you need other lead connector please cut the original connector and solder on the new connector But not Recommena 2012 DJI Innovations All Rights Reserved 7 Mount Center Frame Remove Screws Fix Screws 800CF M2 5 5 x1 x19 Step1 Mount IMU module into IMU position in the center frame Ensure IMU casing is out of touch the top board edge as vibration can cause IMU mal function Step2 Please mount DJI Autopilot System parts onto the bottom board not including GPS modules Please remove all the screws from the bottom board first if necessary Step3 Connect Autopilot System and receiver Please refer to DJI WKM User Manual for details Step4 Please mount the screws to bottom board and use adequate screw glue Step5 Mount the GPS on the top board with a bracket Step6 Configure Autopilot System Please refer to DJI WKM User Manual Notices Make sure to mount the IMU module at the IMU position first O Mount the GPS with a bracket to avoid interference from center frame power board Ensure the USB port of the M C outwards for easy access O Please wire neatly Make sure wires will not be cut by the edge of frames Tips O Install screws with appropriate strength to prevent damage threads 2012 DJI Innovations All Rights Reserved 8 Mount Fr2. For removing screws in the bottom board please proceed with cautious avoiding damages Do not remove any other screws fixed with glue Notice matching the indications is very important please pay attention to them Flight Attention e With DJI WKM autopilot system make sure the output signal of WKM F1 F2 and M1 M6 are all normal to avoid serious damage s and injuries e Keep flying multi rotor a distance from people building high voltage lines etc Make sure to use 6S LiPo power battery e Do not get close to or touch the working motors and propellers which will cause serious injury e Do not over load the multi rotor e Make sure the propellers and the motors are installed correctly and firmly before flying Make sure all parts of S800 are in good condition before each flight Do not fly with wore or broken parts e Strongly recommend you use DJI parts as much as possible Others if you have any problem you cannot solve please contact agents or DJI customer service 2012 DJI Innovations All Rights Reserved 5 In Box 800CF Center Frame Frame Arm 800FA 800TF T Frame x2 Aluminum Ring 800AR x2 y Base Pipe 800BPIx2 Bi pod Drawbar 800BD x4 a T Silicone Rubber Damper 800SRD x4 Nonslip Damper 800ND x4 ap LH HU 3 PIN Se
3. Fix T frame notch into H frame bulges outwards make sure T frame will not move 3 Put the bi pod on the flat floor to adjust H frame and T frame 4 Tighten all hexagonal socket head cap screws including and Notices Put bi pod on the flat floor to finish mounting smoothly and correctly e Please mount the screws and use adequate screw glue Separate the bi pod by disconnecting the H frame to make for easy carriage Completed Quick Disassembly 2012 DJI Innovations All Rights Reserved 12 Assembly Assembly Align knob to mark Insert knob into arm Rotate knob Step1 Align all knobs on the H frame to the marks refer to fig 1 Step2 Lie frame and bi pod horizontally insert knobs into arms and first and then adjust to insert others into the arms Step3 Rotate the knob to the end as fig 2 shown Notices e Ensure all knobs on the H frame aligned to the marks and they would go through the arms successfully Tips e Itis convenient for you to carry S800 by quick disassembly Frame Bi pod Frame and Bi pod 2012 DJI Innovations All Rights Reserved 13 ESC Sound ESC State Ready Throttle stick is not at bottom Input signal abnormal Input voltage abnormal Tips Sound 11234567 BBBBBB B B B BB BB BB BB DJI ESCs are specially designed for multi rotors When use with DJI autopilot systems you do not have to
4. 03 8031504 8031502 S8031503 8031504 21
5. 1 S8032101 S8032203 S8032204 Head cup 3X22 M2 5X8 8032102 8032103 M2 5X8 S8031601 M2 5X8 S8031801 S8031901 F a 8031604 S8032001 Note1 All unlabeled screws are M2 5X5 Note2 1 Left and right T frames are different 2 Left and right bi pod top mounting hubs are different 3 Left set middle set and right set of bi pod carbon tube bracket are different NO 13 14 15 16 17 18 19 20 21 Name Components H Frame S8031301 S8031302 Bi pod Top Mounting Hub S8031401 S8031402 8031501 S8031502 S8031503 S8031504 H Frame w Bi pod Top Mounting Hub 58031505 S8031506 S8031507 13 14 T Frame Right 8031601 S8031602 S8031603 T Frame Left S8031601 S8031602 S8031604 T Frame Nonslip Damper 4pcs S8031801 T Frame Silicone Rubber Damper 4pcs 8031901 Bi pod Carbon Tube S8032001 Bi pod Drawbar 58032101 S8032102 2pcs S8032103 2012 DJI Innovations All Rights Reserved 20 22 23 24 25 26 27 28 Battery Tray Bi pod Carbon Tube Bracket Left Set Bi pod Carbon Tube Bracket Middle Set Bi pod Carbon Tube Bracket Right Set Screw Pack M2 5X5 Screw Pack M3X8 Screw Pack M2 5X8 2012 DJI Innovations All Rights Reserved 8032201 S8031501 S8031505 8031501 S8031506 8031501 S8031507 10pcs 10pcs 10pcs S8032202 S8032203 S8032204 8031502 S8031503 8031504 8031502 S80315
6. 3 S8010401A S8010402 S8010403 S8010404 S8010401B S8010402 S8010403 S8010404 8010601 S8010602R S8010601 S8010602G l or2 3 4 or 5 6 or 7 o The diagram is only for counter clockwise rotation propeller and frame arm o For clockwise propeller and frame arm it is S8010201B and S8010104B Ensure to solder thick wires and fine wires correctly when solder ESC to frame arm Clockwise and counter clockwise motor should be soldered to ESC correctly by different color order 2012 DJI Innovations All Rights Reserved 18 For arms For arms Thick wire y 1 7 g Tg o iy Ss 1 Sy 1 T 7 o 7 Y z Ig 1 NO Name 9 Arm Mounting Bracket 10 Center Frame Support Pillar 11 Center Frame Top amp Bottom Board 12 Top Board Cover for Arm Mounting Bracket 2012 DJI Innovations All Rights Reserved T2X9 lt 58021201 lt gt 7 mooo M2 5X5 S8021101 S8021001 S8020901 S8020902 S8020903 S8020904 S8021102 Components 8020901 S8020902 S8020903 S8020904 S8021001 S8021101 S8021102 S8021201 19 Bi pod S8031603 S8031602 Head cup o S8031402 S8031301 8031302 S8031507 S8031506 S8031501 8031502 S8031505 EA 58031503 8031303 gt pl S8031505 S8032201 M3X8 8032202 Y 8031504 Maxi 8031507 S8031506 803140
7. Spreading Wings S800 User Manual V 1 4 ciji www dji innovations com 2012 DJI Innovations All Rights Reserved 1 Disclaimer Read this disclaimer carefully before using Spreading Wings S800 By using this product you hereby agree to this disclaimer and signify that you have read them fully Spreading Wings S800 is an excellent multi rotor With a good autopilot it will offer tremendous flight features Despite the controller of DJI autopilot operate in the safest manner when the main power battery is connected we strongly recommend customers to remove all frame arms and keep children away during system calibration and parameter setup DJI Innovations assumes no liability for damage s or injuries incurred directly or indirectly from this product usage DJI Spreading Wings is registered trademark of DJI Innovations Names of product brand etc appearing in this manual are trademarks or registered trademarks of their respective owner companies This product and manual are copyrighted by DJI Innovations with all rights reserved No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI Innovations No patent liability is assumed with respect to the use of the product or information contained herein 2012 DJI Innovations All Rights Reserved 2 S800 Profile DJI Spreading Wings S800 is a multi rotor designed for AP It simplifies users installation and enabl
8. ame Arms Step 1 B00CF xt Copper contacts H 800FA x6 Propeller i Screw H Cover H Motor i Renae H ESC Motor rotation direction LED A A Clock wise H GAO Counter clock wise Green H 800CF x1 x1 800FA x6 x6 Horizontal Step1 Check arms 1 Make sure copper contacts are in good condition without bend or severe wear 2 Make sure propellers are without crack and screws in propeller cover tight 3 Make sure motors are mounted firmly and rotate freely 4 Distinguish LED indicator on the ESC bottom With a red point in is red LED others are green LED We recommend you mount arms with red LED to M1 and M2 5 Distinguish marks and on the arms Arm gt Center frame Arm gt Center frame Step2 Insert frame arm into center frame vertically Step3 Slowly rotate the frame arm upward until positioned completely Step4 Press down the buckle to lock the arm Make sure the arm does not move Step5 Make sure the buckle is pressed down correctly about 35 under normal circumstances Notices Please add some lubricant at the position 1 if it is hard to press down the buckle 2012 DJI Innovations All Rights Reserved 9 e Slowly rotate the frame arm to prevent from breaking the copper contacts e Please refer to 2 to ensure the arm is perfectly positioned Make sure use appropriate strength to press down the buckle correctly e Do no
9. e Parallel cae Parallel So Parallel 2012 DJI Innovations All Rights Reserved 16 Trouble Shooting If the motor mount loosens please tighten it by following the procedures Step1 For arms For arms Step2 Motor mount screws Step3 For arms For arms e ZA IZ 7 SOS arca hato 7 Nu pa IN e Step1 Remove Please unscrew the screws on the top Step2 Tighten Retighten the motor mount screws on the back to make the motor firmly attached Step3 Remount Remount the screws on the top Notices Shim should be mounted in the correct position as shim mount position of arm is different from arm Tips e Please use adequate screw glue e Install screws with appropriate strength 2012 DJI Innovations All Rights Reserved 17 Spare Parts Listing If S800 needs part replaced please refer to the following diagram to identify the part with the NO and components and then make a purchase Each package includes screws needed S8010402 S8010403 8010104 NO Name 1 15 Propeller cowO 2 15 Propeller cw 3 4114 Motor 320KV 4 Frame Arm Counter Clockwise 5 Frame Arm Clockwise 6 ESC Red LED 7 ESC Green LED 8 Frame Arm w ESC Motor amp Prop Notices S8010602R H it 8010602G a i A i _2 5x5 Components S8010201A S8010201B S8010301 S8010302 S801030
10. es quick disassembling Frame arm integrates with ESC and motor With DJI WKM autopilot system it can achieve hovering cruising and other flight elements S800 can be applied for aerial photography and other aero modeling activities 1uBlaH WWOZE gt 2012 DJI Innovations All Rights Reserved 3 Contents DI o enne E E A N 2 e1010 mA KEN S ESA A A E A A a do a 3 Contesta ida cda es 4 Product Usage Call AAA A 5 A A NO 6 LN A totes a tte cases dasa neste ena ee a 6 Genter Frame Wiring cece issa etesde es eons the ease ta 7 Mount Center Frame iii doves aie eae a Ls ieee 8 Mount Fraime Ariss adan TT 9 Mount Bpod srs aoe darle la rod 11 Asics ete anh ah sic lsat eed ead a ee 13 ESC S nden nra ee i ie ee ee Ae ne Fa esi 14 SECC ode abad Pacino 14 Aprenda id A 16 Mount Battery Brackets nade ee nana cancer 16 Trouble ShOoting 2 4 ge sae ai ii I ee ti 17 SparePartS isting 5 ccf svcis A cshache sales AE EET 18 2012 DJI Innovations All Rights Reserved 4 Product Usage Cautions When flying the fast rotating propellers of S800 may cause serious damage s and injuries Therefore please fly with a high safety in mind at all time Mount Attention Mount GPS with a bracket to avoid interference from the power board of center frame For IMU position make sure the arrow direction marking is pointing to the aircraft nose Mount the arms correctly Center frame gt Arm Center frame gt Arm
11. rvo Cable 00SC x1 Screw Package 800SP x1 Hexagonal screws M3x8 M2 5x5 M2 5x8 Hexagonal socket head cap screws HC3x22 Adhesive Velcro BOOAV x1 Battery Band Tools Needed 2 0mm Hex Wrench 2 5mm Hex Wrench Screw Glue Nylon Cable Tie Scissors Diagonal Cutting Pliers Foam Double Sided Adhesive Tape 2012 DJI Innovations All Rights Reserved 800BB x2 Spare Screw Package For mounting screws For fastening screws For binding devices and wires 800SSP x1 For fixing receiver controller and other modules Center Frame Wiring Top board is power distribution board and the bottom board is for loading autopilot system components Top Board Mark Motor clock wise Mark Motor number XT60 Female To Gimbal ESC signal outlet To main controller Circuit line E Parallel XT60 Male To Battery IMU mount position XT60 Female To PMU Notices For IMU position make sure the arrow direction marking is pointing to the aircraft nose Connect the motor 3 pin connector M1 M6 from WKM M C to ESC signal socket M1 M6 on center frame markings accordingly WKM M C M1 ESC signal socket M1 WKM M C M6 gt ESC signal socket M6 Tips Main battery power leads gimbal and PMU leads are on the bottom surface of the top board Markings and stand for the propeller rotation direction
12. setup any parameters or calibrate travel range Specifications Frame Diagonal Wheelbase Frame Arm Length Frame Arm Weight Including Motor ESC Propeller Center Frame Diameter Center Frame Weight 800mm 350mm 304g 240mm 365g Bi pod Size 500mm Length x415mm Width x320mm Height Top width 145mm Bi pod Weight 4289 Total Weight 2 6Kg Motor Stator Size 41x14mm KV 320rpm V Max Power 360W Weight 1479 ESC 2012 DJI Innovations All Rights Reserved 14 Current 40A OPTO Voltage 6S LiPo Signal Frequency 30Hz 450Hz Drive PWM Frequency 24KHz Weight 18g Propeller Material Carbon Fiber Size 15x04in Weight 159 Flight Parameters Takeoff Weight 5 0Kg 7 0Kg Load Weight OKg 2 5Kg Power Battery Max Power Consumption Hover Power Consumption Hover Time 2012 DJI Innovations All Rights Reserved LiPo 6S 10000mAh 15000mAh 15C Min 2100W 720W Takeoff Weight 6Kg Max 16 min 10000mAh amp 6KgTakeoff Weight 15 Appendix Mount Battery Bracket Step1 Mount the retaining clip and the bracket fix screws but not tighten M 2 5X5 Bracket Notch Outwards Retaining Clips Chamfer Outwards Step2 Place the mounting board and adjust its position and then tighten all screws Battery Mounting Board A 5 ES Loft Rb cores e A PA Mm i tr
13. t hot plug arms e f the motor mount loosens please tighten it by following the procedures in trouble shooting of Appendix Tips e LED is on after motor start Examination Arms are aircraft nose direction arms are aircraft tail See from top motors on arms rotate counter clockwise motors on arms rotate clockwise 2012 DJI Innovations All Rights Reserved 10 Mount Bi pod Step1 800TF 800BP 800SRD 800ND Step3 M2 5X8 HC3X22 Step1 x4 x2 Mount T frame 800TF and base pipe 00BP D TH frame bulges outwards MT frame notch 1 Put nonslip damper 800ND through the base pipe 2 Put the base pipe into T frame until the head of nonslip damper is embedded into T frame 3 Embed the other nonslip damper into the T frame 4 Put silicon rubber damper 800SRDj onto both sides of the base pipe Mount H frame B00HF and bi pod drawbars 00BD 1 Fix but not tighten hexagonal socket head cap screws bi pod drawbar Fig M2 5x5 Fig to H frame and 2 Adjust drawbar and T frame and fix but not tighten hexagonal socket head cap screw M2 5x5 Fig to drawbar and aluminum ring 2012 DJI Innovations All Rights Reserved 800AR 11 Step3 Mount H frame and T frame 1 Insert T frame through aluminum ring until it plugs into H frame 2
Download Pdf Manuals
Related Search