UVC - Pond Clarifier UV Light
Contents
1. Ce A Operation Manual UVC Pond Clarifier UV Light LICHT KRAFT TECHNIK se Read and follow the operating instructions and safety information before using for the first time Technical changes reserved Due to further developments illustrations functioning steps and technical data can differ insignifi cantly Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us by WilTec Wildanger Technik GmbH Seite 13 http www wiltec info fy cE R The information contained in this document is subject to change without prior notice No part of this document can be copied or duplicated in another form without the prior written consent of Wiltec Wil danger Technik GmbH The Wiltec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram Although Wiltec Wildanger Technik GmbH has made every effort to make sure that this user manual is complete accurate and updated errors cannot always be avoided In the event of problems with this user manual please complete and send this form back to us FAX notification 49 2403 55592 15 from Name Firm Tel Fax I would like to report the following mistakes Customer Service Wiltec Wildanger Technik GmbH e mail service wiltec info Tel 49 2403 55592 0 Introduction Thank you for purchasing this quality product To minimize the risk of injury by m2. eans of fire or electric shock we urge that our clients take some basic safety precautions when using this device Please read the operation instructions carefully and make sure you have understood its content Always use a grounded power connection with the appropriate mains voltage You can find the corre sponding mains voltage on the type plate If you have any doubts about the connection being grounded have it checked by a qualified professional Never use a faulty electric cable Do not inspect the electrical part of the pressure pond filter in a wet or damp environment or when you are wet yourself and protect it from direct sunlight Install this device in a safe location so that nobody can step on the cable fall over or damage it Make sure additionally you provide sufficient cooling through the ambient air and avoid heat accumulation Disconnect the power plug before cleaning it and use only a damp cloth for cleaning The electric part of the device contains no parts that can be inspected or serviced by the user Leave the maintenance adjustment and repair to qualified technical personnel In case of unauthorised inter vention the 2 year warranty is no longer valid Keep these operation instructions safe by WilTec Wildanger Technik GmbH Seite 14 http www wiltec info C Ci Safety guideline A BEWARE The use of this device is allowed on standing bodies of water garden ponds water or swimming ponds and their surroundin
3. g areas only with fault current protection switch with a triggering nominal current up to 30mA according to VDE 0100 Article 702 and 738 The device is not suitable for use in swimming pools paddling pools and other bodies of water in which during operation people The operation of the device during the stay of people in the danger zone is not allowed Ask your electrician The device is not intended for use by persons including children with impaired or limited physical sensory and mental abilities or lack of experience and or real Knowledge unless they are supervised by a person responsible for their safety or you follow the instructions made by this person how to use the device correctly Children should be supervised to make sure that they do not play with the device A ATTENTION e Run a visual inspection of the device before every use Do not use the device if the safety ap pliances are damaged or worn out Never override safety regulations e Use the device exclusively according to the intended purpose stated in the instructions for use e You are responsible for the safety of the working environment e Ifthe cable or the plug is damaged due to external influences the cable must not be repaired It has to be replaced with a new one This work can be carried out only by an electrician e The voltage indicated on the type plate of the device of 230 Volt alternating voltage has to cor respond to the existent mains voltage e Neve
4. http www wiltec info
5. is device can only be worked under the protection of the cover It should be placed in some where that water will not submerge it and it should be installed 2 meters away from water Connection We would suggest choosing o hose that can have pressure of O bar Cut off the multistage hose toil according to the diameter of the hose Connect the multistage hose tail to the inlet or outlet and fix with hose clip Put O ring into the screw and connect to the device You can change the two inlet checking windows to water supply hose if necessary Important Connect the water pumps first and then connect the UV device Do not run the device without water This device will be automatically turned on after the power cord is connected to the power supply The device is working if the blue light is turned on by WilTec Wildanger Technik GmbH Seite 17 http www wiltec info 1 The light tube should be replaced after 8 000 hours use Turn the head according to the direction of arrow Take out the head according to the direction of arrow Take out the UV lamp according to the direction of arrow and replace it Only for the UV lamp that have the same name brand and power Both inside and outside of the casing should be cleaned Loose the four screws by screwdriver Take out the brackets according to the direction of arrow Take out the quartz glass tube according to the direction of a
6. ns are prohibited for safety reason 19 The UVC lamp installed in the unit is intended to kill algae and bacteria in the pond water Even in small doses its radiation is harmful for eyes and skin 20 Never use the UVC lamp in a defective housing or outside the housing or any other purpose other than that intended The following restrictions apply to the unit Never use the unit to convey fluids to other than water Never use the unit without water Do not use for commercial or industrial purposes INSTRUCTION 1 This equipment can kill the harmful gems and algae in the aquarium and the pond which offer the heath environment to the fishes 2 When the water under the irradiation of wavelength in 253 7nm s ultraviolet radiation in a short peri od the germ and pathogen in the water will be killed then 3 This equipment is not sell with the pump please buy it yourself 4 Please connect the inlet pipe with the outlet of the water pump 5 Please connect the outlet pipe with the other filter or the pond and fix it After the inspection of the pipe an connecting part the water circulation can be started then 6 Please check it when the water started circulation or not after several minutes 7 Turning on electrical source the UV filter begin to work 8 The detailed sketch map of usage can be pound in the packing box by WilTec Wildanger Technik GmbH Seite 16 http www wiltec info Installation location Th
7. r lift carry or fixate the device by using the power cable e Make sure that the electrical plug connection is placed in a flood proof area and is protected from moisture e Before working on the pond pump disconnect the appliance by taking the plug out of the socket e Avoid exposing the appliance to a direct water jet or rain e The user is responsible for the compliance with location specific safety and installing regula tions Ask an electrician e Consequential damage arising from flooded rooms caused by dysfunctions of the appliance must be avoided by means of the appropriate measures installing an alarm system reserve pump e In case of malfunction the repair work can be carried out only by a qualified electricial or the WilTec service e The appliance must not run dry or with a completely closed intake port e The appliance must not be used for swimming pools e The device cannot be employed for potable water circuits by WilTec Wildanger Technik GmbH Seite 15 http www wiltec info CE l The UVC filter should placed om somewhere that the water will not submerge it and it should be 2 meters distance from the edge of the pond to the fitter This equipment cannot be used under the water 2 Before the water circulation the electrical source of the UVC filer cannot be switched on 3 Please place the UVC in the steady and safe spot Because the UV light tube is made of quartz glass which is easy to broken 4 Befo
8. re all parts are installed completely the electrical source cannot switch on 5 If the UV light tube or the body shell looks like broken the equipment cannot be used 6 When any person in the water the UVC cannot be used 7 Please make sure that the electrical voltage frequency used are consistent with the indication on the UVC station 8 When installing the equipment the installation regulation of domestic should be followed 9 Pull the connecting cable is forbidden And please protect the connecting cable from heat greasi ness or sharpness Make sure the max pressure of the body shell ensured is less than Obar ll When know the frost is coming please move away UV filter I2 When install the UV filter please not let it under the sunlight directly I3 The dirtiness on the quartz tube will influence the effect of the equipment please clean the quartz tube in time l4 In order to ensure the effect of the equipment the UV light tube should be replaced after 8000hours usage I5 When the body shell is blocked with the sands rubbish it may destroy the quartz tube So please add the filter sponge in the inlet of the water pump I6 UVC is harmful to the eyes and skin Please do not watch UVC directly or let the skin approach to UVC 7 When install or repair this equipment the electrical source of the aquarium must be switched off I8 The product must be installed horizontally and with the feet down Other installation positio
9. rrow Check the quartz glass tube and clean it with clean and wet cloth Please use vinegar to clean the quartz glass tube if there is much incrustation CUV 1er Serie SCREW Dichtung Schraube RUBBER RING Kabeldurchf hrung CABLE BOLT Ausgang OUTLET PIPE SEALING COVER O RING 2 SWITCH COVER l UV C LAMP Geh use T BODY SHELL Halterungen LAMP HOLDER Durchflussmesser GAR PERTE QUARTZ FITTING s LOW METER Glow starter SUPPORT OF LAMP HOLDER INLET O RING 1 FE i Eingang BIG SCREW FIXING BRACKET SCREW Schraube um by WilTec Wildanger Technik GmbH Seite 18 http www wiltec info CE Ci CUV 2er Serie NUT HELIX OUTLET O RING 1 RUBBER RING NUT EE INDICATOR GLASS SCREW 3 9x16 ADJUSTABLE SWITCH SCREW UVC DEVICE HEAD 3 9x19 UD CUV 3 Serie by WilTec Wildanger Technik GmbH Seite 19 http www wiltec info 1 indicatorgloss 2 Bodyshel a wigo Ca outlet 5 Gasken 6 Nu 7 Upperbracter 8 Stainlesssteeihose 9 Oring by WilTec Wildanger Technik GmbH Seite 20 http www wiltec info C Ci Disposal regulations EU guidelines regarding the disposal of scrap electric appliances WEEE 2002 96 EC were imple mented in the law related to electrical and electronic equipment and appliances All Wiltec electric devices that fall under the WEEE regulations are labelled with the crossed out wheeled waste bin logo This logo indicates that
10. this electric equipment must not be disposed with the domestic waste The company Wiltec Technik GmbH has been registrated in the German registry EAR under the WEEE registration number DE45283704 Disposal of used electrical and electronic appliances intended for use in the countries of the European Union and other European countries with a separate collection system for these appliances The logo on the article or on its packaging points out that this article must not be treated as normal house hold waste but must be disposed to a recycling collec WilTec Wildanger Technik GmbH tion point for electronic and electrical waste equip DE 52249 Eschweiler ment By contributing to the correct disposal of this article you protect the environment and the health of WE E E Reg Nr DE45283704 your fellow men Environment and health are threat ened by inappropriate disposal Materials recycling helps reduce the consumption of raw materials Additional information on recycling this article can be provided by your local community municipal waste disposal facilities or the store where you purchased the article Address WilTec Wildanger Technik GmbH Konigsbenden 12 28 D 52249 Eschweiler Important notice The reprint or reproduction even of excerpts and any commercial use even in part of this instructions manual require the written permission of Wiltec Wildanger Technik GmbH by WilTec Wildanger Technik GmbH Seite 21
Download Pdf Manuals
Related Search