HSTT 100
Contents
1. FFT Mode 6048 3024 1512 6817 3409 1705 Bits rate calculation total Tb otal u fs b i L Where Fs Symbols frequency symbols sec fs 1 Ts Ts Symbol duration Symbol Time Guard Interval time b Number of bits per symbol depending on the modulation L Number of data carriers depending of FFT mode Bits rate calculation useful Tb seful n TD orai Codif sc Codifr ed Salomon u FEC Cod FEC Codification 1 2 2 3 3 4 5 6 1 8 Reed Salomon Cod Codification made by the means of Reed Salomon algorithym 188 204 Case study example For example in the case of a DVB T transmission in Spain the configured parameters would be the following 8k mode 2 3 FEC Ya guard intervals 64QAM constellation for an 8 MHz channel and using the previous formula you will get the following channel useful capacity Tb useful 19 905Mbps Note As you select a configuration with a higher output channel capacity the protection grade against mistakes gets proportionally decreased Next it is shown the channel capacity for systems without hierarchy in all the cases ot constellation guard interval and codification relation for transmissions of 8MHz 7MHz 6MHz y BMHz DVB H The useful capacity channel is identical for modes 2k 4k DVB H and 8k 16 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Useful channel capacity 8 MHz ee Guad Interval Modulation FEC2. the value of C N at the point of pixilation of the signal that is the quantity of dBs of C N measure that are needed to lose the input signal Temperature It indicates the current temperature of the module in C 3 Set Front End In this option you will be able to configure the input parameters of the satellite signal Local oscillator Selection of the local oscillator that you wish to use FI KU C K9750 K10000 K10600 K10700 K10750 K11250 K11300 K11325 Frequency MHz Transponder frequency that you wish to tune Symbol speed Symbol speed required by the transponder LNB Supply In this option you can set the parameters concerning the LNB RF IN Voltage 13V 18V and Off 22 kHz Tone Off On and Auto DisegC Switch A B C D and Off 4 Modulator Set Up This option allows configuring the DVB T DVB H modulator of the device Bandwidth Selection of the Bandwidth of the modulated signal 8 MHz 7 MHz 6 MHz and 5MHz The 5 MHz option is only supported by DVB H standard FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information
3. 368 10 978 11 310 1 520 12 197 12 567 2 096 12 807 13 195 0 368 10 978 11 310 3 824 14 637 15 080 5 551 16 466 16 965 1 279 18 296 18 850 8 143 19 211 19 793 u R a a a a O c w o gt O 3 lt a 17 HSTT 100 version_en_1 1 ANKARO BCN Distribuciones S A D 44536 L nen Zweigniederlassung Deutschland Tel 49 231 8785 01 Auf der Hohe 8 Fax 49 231 8785 100
4. CES sis Programmer Field strength meter Field strength meter Mod HPR 100 Mod MDX 600 Mod MDL 400 Code 20018 11 Code 0001006 Code 0001003 5 3 de Wide band amplifier 47 862MHz Mixer Mod HAMP 100 Mod HAM 100 Code 20042 1 1 Code 20012 11 14 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Chapter 2 Chapter 3 Technical features Ref HSTT 100 Code 20024 11 Input frequency margin 950 2150 MHz Input level 25 to 65 dBm Imput impedance 750 LNB feeding conmutation Input connector Input LOOP losses FEC 13V 18V 7 0 22kHz Female F connector lt 1 dB 1 2 2 3 3 4 5 6 7 8 8 9 9 10 1 4 1 3 1 5 2 5 3 5 4 5 DVB RS 204 188 Input modulation Input Symbol Rate Modulation Error Ratio MER Selectable format of output modulation QPSK 4 30 MS s Typ 38 Min 36 DVB T DVB H Bandwidth MHz Mode DVB T 6 7 8 DVB H 070 7 8 DVB T 2k 8k DVB H 2k 4k 8k Output channels C2 C69 Output connectors Female F connector Output Level 80 dBuV Regulation margin 15 dB MIX Losses lt 1 dB Band spurious 60 dBc Programming Interface RJ 45 Programmer HPR 100 MDX and MDL Operating temperature 0 C 45 C Consumption 5V mA 650 Consumption 12V mA 300 Consumption 24V mA 15 Consumption 30V mA 2 Dimensions 75x265x150 mm Weight 1 4Kg Declaration of conformity CONFORMITY DECLARATION WE ANKARO DECLARE THAT THE PRODUCT IS IN CONFORMITY W
5. bits and 1 redundant bit Modulation Output modulation format 4 QPSK 16 16 QAM 64 64 QAM Advanced settings Mode Selection of the modulation standard DVB T and DVB H Note The output useful bits rate will depends on the following parameters Bandwidth guard interval FEC coditication and modulation In the Attachment you will find all the information related to the resulting useful bit rate in each configuration De HSTT 100 version_en_1 1 ANKARO 5 Set Output channel In this option you can configure the different parameters of the cable signal Channel standard It allows you to select the channelling of the cable signal standards Options BG BG PAL BG IT 11 M NTSC PAL M PAL N PAL DK PAL I BB_AU DK PAL L PAL Channel Output channel of the cable modulation When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C2 C69 Frequency MHz Output frequency of cable modulation When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 47 862 MHz Level Regulation of the output level of the modulated signal Options 0 15dB Calibration Allows the realization of two tests in order to verify the correct running of the device Deactivate
6. output It allows activating or deactivating the output of transmodulator Switch output to CW It allows activating or deactivating the DVB T DVB H modulation allowing visualizing the carrier without modulation in the selected frequency 6 System This option provides information of the regenerator System logfile In this field are indicated the registered events in the module Read log It allows reading the registered events in the module Clear log It allows deleting all events stored until this moment Export log to USB It allows you to export all events registered to the connected USB device NM low Limit dB An event of error will be recorded when the value of Noise Margin is lower than the set value NM hight limit dB Once the event of error is recorded Noise Margin lt Limit Lower NM this will be Noise Margin value that will have to be exceed so the module stops being in error Clear log all devices It allows deleting the events report of all the interconnected modules Factory default This option restores the values by default of the regenerator System information It allows you to visualize the basic information of the module model no of series firmware version etc Settings This option allows saving and loading the configuration of the module carrying out firmware update or making an adjustment of the time and date of the module Clock Set Date and time Setting of the date and time
7. the module been correct Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memory correspond to the channel that you wish to copy 3 Config In Config option the information concerning the transmodulator is given Read log It allows reading the registered events in the module 1 Select the option Read LOG file 2 Press OK again to show the log file 3 A new window will appear It will through Up Down buttons Press OK show the information about the to continue registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment Factory default This option restores the values by default of the transmodulator Update FW It allows carrying out the firmware update from the programmer Output services This option allows making the selection of the services that you wish to include in the output multiplex Once you have tuned a transponder and
8. you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services 12 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Add Services 1 Select the option Add services 2 Select one of the transponder 3 A window will appear and it will let through Up Down buttons Press OK services you want to add through you know that the operation made has to continue Left Right keys and select the Add been correct button to include the service in the multiplex Delete Services 1 Select the option Delete services 2 Select the service you want to 3 A window will appear and it will let through Up Down buttons Press OK delete with the Left Right keys Then you know that the operation made has to continue press OK over Rem in order to been correct remove it or press OK over All in order to delete all the services of the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Date Hour Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date SW version info It allows you to visualize the basic information of the module model firm
9. EC rate in each configuration Output configuration TV output In these options you can configure the output parameters of the terrestrial signal RF Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 47 862 MHz RF Level Regulation of the output level of the modulated signal Options 0 15dB Summary table Satellite input Terrestrial output TV output LO frequency Modulation RF Channel Input Frequency Invert Spectrum Inversion RF Level Symbol Rate Guard Interval Gl Antenna Bandwith BW Diseqc Tx Mode FFT Mode FEC Mode 2 Auto This option allows saving and loading the configuration of the module in the HPR 100 programmer 11 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of
10. HSTT L 00 User s manual English User s manual HSTT 100 NOTE This user s guide is adapted to software version 0 0 26 of HSTT 100 dated 25 10 2010 For future software updates you can download the user s guide from the following website http www ankaro com Chapter 1 Installation 1 1 Safety Measures 1 Never place the device next to hot sources 2 Never undergo the device to temperatures that exceed its level of operation 3 Never expose the device to leakings nor spatterings 4 Never place objects that contain liquids over the device 5 Respect the ventilation slots of the device do not cover them with any kind of object 6 The space around the device must be free of objects in a minimum radius of 40cm 7 Avoid locations with possibilities of spilling liquids on the inside of the device and with important changes of temperature 8 Never open the device by yourself due to electric risk In case of problems go always to qualified technicians 9 Never under no circumstances open the device when connected to the electrical net 10 During the handling it is better to disconnect the device from the electrical net 11 Obey the electricity security rules during the assembling Use materials that obey the current law 12 The connecting plug must be accessible in a fast and simple way to have a fast disconnection 13 Never touch the plug with wet hands Also disconnect always the device before h
11. ITH FOLLOWING DIRECTIVES Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC If you wish a copy of the conformity declaration please contact to the company HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 ATACHMENT Depending on the configured parameters we are going to obtain one particular channel capacity output useful bit rate In order to make an estimation of this output bits rate we have to take into account the following parameters Symbol duration Ts For signals of 8 MHz 2K 1705 carrier Mode 8K 6817 carrier 4K 3409 carrier Symbol duration 896 us 448 us 224 us Guard Interval ie 1732 1 16 Duration 1 32 Tus For signals of 7 MHz Mode 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 1024 us 512 us 256 us Guard Interval 32us For signals of 6 MHz 8K 6817 carrier 4K 3409 carrier 9K 1705 carrier Symbol duration 1194 6 us 597 3 us 298 6 us 29864 Duration 298 7us 149 3us 74 7us 37 3us 149 3us 74 6us 37 3us 186us 74 6us 37 3us 18 6us 9 3us For signals of MHz 2K 1705 carrier Modo 8K 6817 carrier 4K 3409 carrier Symbol duration 1433 6 us 597 3 us 298 6 us Guard Interval 1 16 1 32 1 16 1 32 1 16 Duration 358 4us 179 2us 89 6us 179 2us 89 6us 1 32 11 2us Modulation Modulation QPSK 16 QAM 64 QAM Number of bits per symbol 2 4 6 FFT Mode
12. andling the connections 14 Never put any heavy object over the device since it could get damaged 15 If the device is going to remain some time without use it is recommendable to disconnect it from the electrical net 16 The repairmen and the maintenance of the device must be done by TV and radio specialised technicians 1 2 Box content HSCT HSSCT HSTT HSATT HTTR Fell Quick installation guide 2 x Bridge F male F male DC Cable HSTT 100 Cable 12 cm PIN to PIN RJ45 RJ45 1 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 1 3 Description and connections The module HSTT 100 is used for the reception of free channels that obey the DVB S standards Each module allows the reception of a complete transponder in DVB S QPSK and the subsequent modulation in DVB T COFDM of it A feature of this equipment is its modulator in Vestigial Side Band or VSB This modulation can be used to distribute adjacent channels in one distribution without any intermodulation problem Each module has one Loop connector to cascade several modules at input and a Mix connector to do same in output channels The output channel is selectable between C2 and C69 All parameters are programmed by the means of HPR 100 or the MDX or MDL series of field strength meter and they are monitored in the display of programmer or in the 5 TFT screen of field strength meter HSTT 100 n 4 1 Two colored led It indica
13. ard in order to move to the different options and to get into the submenus we have to press OK button 1 Manual Inside the manual menu there are specified the different options for setting up the input output and modulation parameters 1 This field shows the type of parameter that is selected at the moment Options Input Sat Out Terr Out TV 2 This field shows the parameter that is selected In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press Cancel 10 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Satellite input Input Sat In these options you will be able to configure the input parameters of the satellite signal LO freq Local oscillator Selection of the local oscillator that you wish to use FI KU C K9750 K10000 K10600 K10700 K10750 K11250 K11300 K11325 Freq Input Frequency MHz Transponder frequency that you wish to tune In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Symbol Rate Symbol speed required by the transponder In order to introduce the symbol rate press the OK button and the cursor wil
14. codification 1716 1739 5 855 6 032 7 806 8 043 8 782 9 048 8 709 9 676 10 246 10 556 11 709 12 064 15 612 16 086 17 564 18 096 19 516 20 107 20 491 21 112 17 564 18 096 23 419 24 128 26 346 27 144 29 273 30 16 30 787 31 668 Useful channel capacity 7 MHz ee Guad Interval 6 123 5 278 6 83 7 037 7 684 7 917 8 538 8 797 8 709 9 676 10 246 10 556 13 661 14 075 15 369 15 834 17 076 17 594 15 24 16 934 17 93 18 473 13 063 14 515 15 369 15 834 17 418 19 353 20 491 21 112 9 595 93 053 93 751 21 772 25 614 26 39 22 861 26 895 27 71 Useful channel capacity 6 MHz Guad Interval 1 8 1 16 1 32 4 147 4 391 4 524 5 529 5 855 6 032 6 221 6 587 6 786 6 912 7 318 7 54 7 257 7 684 7 917 8 294 8 782 9 048 1 059 11 709 12 064 2 441 13 173 13 572 3 824 14 637 15 08 4 515 15 369 15 834 2 441 13 173 13 572 6 588 17 564 18 096 8 662 19 76 20 358 20 735 21 955 22 62 21 772 23 053 23 751 Modulation FEC codification 1 2 3 732 4 976 5 599 6 221 6 532 7 465 9 953 1 197 2 441 3 063 1 197 4 929 6 796 8 662 9 595 QPSK Useful channel capacity 6 MHz Modulation Codificaci n FEC 1 4 3 110 4 147 4 665 5 184 5 443 6 221 8 294 9 331 0 368 0 886 9 331 2 441 3 996 5 551 6 329 Note Only aplicable for DVB H 1 8 1 16 1 32 3 456 3 659 3 770 4 608 4 879 5 027 5 184 5 489 5 655 5 760 6 099 6 283 6 048 6 404 6 598 6 912 7 318 7 540 9 216 9 758 10 053 0
15. e you have chosen the option services you want to remove service select the Add Remove button to remove the service in the multiplex Remove all services It allows removing all the services included in the multiplex Modity LCN The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically Note If in the existing installation there are already services that have LNC system you will have to configure the position of the module services in order to avoid conflicts with other net services Bandwith limitation It allows selecting the of the capacity of the output channel Auto service addition On It selects the services automatically when an input carrier is tuned and when the list of selected services is empty The receiver will have this state by default Always It selects the services automatically every time a new input carrier is tuned This state is only recommended to be used for making test in the module Off The automatic mode is deactivated the services have to be manually selected Advanced settings Network It allows making the adjustment of the identification parameters of the multiplex TS ID Transport Stream identification value It is recommended to configure a value different from TS ID for each one of the outpu
16. external USB 2 0 storage device Write Alias It allows saving the alias of the module in the program Options Yes No 8 Set Output Services This option allows making the selection of the services that you wish to include in the output multiplex Add Remove services It allows adding the services to the multiplex and also removing the ones previously included The lower bar informs about the available space in the output multiplex As you add more services the space available will decrease Once you have tuned a transponder in the Input Set Up section and you have selected the DVB T DVB H modulator configuration in the Modulator Set Up section you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services Adding services 1 Select Service to add option 2 Select one of the transponder 3 Once you have chosen the services you want to add service select the Add Remove button to include the service in the multiplex variability of the bits rate of the inputs services Excessive capacity It is recommended to remove services N Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible Recomendad capacity lower to 85 8 HSTT 100 version_en_1 1 ANKARO Removing services 1 Select the Service to remove 2 Select one of the transponder 3 Onc
17. iguration of a module or group of modules Load program It allows loading a previously created program on a module or group of modules Delete program It allows deleting a program Device to process Current The creation or loading of a program will be applied only in the module that is currently connected All The creation or loading of a program will be applied to the whole group of connected modules 7 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Working disk With this option we have the possibility of choosing if we want to work into the internal disk or in the external storage device USB 2 0 Once the option is selected a dialog box will appear and we will be able to choose among three different options Auto The Meter decides where the data will be stored If there is external memory connected the Meter will store the data in it If not it will use the internal memory USB The Meter always will try to use the external memory connected to the USB port If this memory has not been connected an error message will be shown reminding that there was an error storing the data and it will be not stored Internal Always the internal memory is used to store the data Load programs from USB This option allows importing programs from a USB memory to the field strength meter Before using this option you must connect a USB memory Save programs to USB This option allows copying the programs stored in the
18. l be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Antenna Feeding tone towards the LNC Options OV 13V 13V 22kHz 18V 18V 22KHz 13V AUT 18V AUT DisegC In this option you can set the DisegC configuration A B C D and None Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Modulation Output modulation format QPSK 4 QAM 16 QAM 64 QAM Invert Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Gl Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 BW Bandwidth Selection of the Bandwidth of the modulated signal 8 MHz 7 MHz and 6 MHz and 5MHz The 5 MHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 8 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Affachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard interval F
19. of transmodulator It is appropriate to maintain these parameters set in order to have the registration ot errors linked to the current time and date Set date time all devices Loading the current date and time of the module in the rest of interconnected modules Alias Write alias It allows you to assign a name alias to the module you are programming Option only available when the Alias Auto option is configures as none manual mode Auto Alias It allows configuring the name alias of the modules automatically Options Channel Frequency Service None Upgrade Send Firmware from USB It allows carrying out the firmware update from the USB device Send firmware to all It allows carrying out the update ot all the modules that are interconnected at the same time 0 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Configure all devices Input values to all devices It allows copying the current input configuration in all the interconnected modules Modulator values to all devices It allows copying the configuration of the current modulator in all the interconnected modules Output values to all devices It allows copying the current output configuration in all the interconnected modules Factory default to all devices It allows making values by default to all the interconnected modules 7 Program management New program This option allows creating a program with the current conf
20. ogramming both from corresponding MDX and MDL field strength meter as well as from HPR 100 MDX MDL In order to start programming the HSTT 100 transmodulator you will have to go to Tools option through the key 8 of your field strength meter and to select the Transmodulator Prog option Then it will proceed to recognize the module and to show the main menu In the Transmodulator Prog are shown the different configuration options that this tool offers 1 Select Device The field strength meter allows carrying out the programming of one or several transmodulators from an only transmodulator Without interconnection of modules Interconnection of several modules you can select which An only module connected module you wish to program 4 HSTT 100 version_en_1 1 ANKARO 2 Device Status In the option Device Status are specified the main parameters of the module at this moment Front End It indicates whether the module is hooked or without signal Input bit rate Transfers of data in the satellite tuner input Output bit rate Transfer of data in the module output BER before and after Viterbi It indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm MER Parameter that indicates the quality of the input modulated digital signal expressed in dB Noise Margin It indicates the difference between the value of current C N and
21. t multiplex configured Net ID Net identification value Original Net ID Original net identification value Network Name Name associated with the net 9 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Services Change service name It allows changing the name of the service manually In order to do so please choose the service in the first line and then write the new name in the second line Then you have to press modify in order to save the changes Next it is attached the identification table NID ONID of the main satellites You will be able to find more information in the law ETSI TR 101 162 v1 2 1 Satellite Net ID Original Net ID Description Hotbird 13 E Eutelsat 13 E 318 318 Eutelsat 13 E System Astra 19 2 E 1 Astra Satellite Network 19 2 E Astra 23 3 95 Astra n n 1 23 Astra 28 2 E 2 Astra Satellite Network 28 2 E Nilesat 7 W 2048 Nilesat 101 Hispasat 30 W 33 Hispasat Network 1 HPR 100 Note From HPR 100 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a MDX or MDL series field strength meter When you connect the HPR 100 programmer it will proceed to recognize the module and to show the main menu In the main menu are shown the different options for configuring the transmodulator We have to use the Up and Down buttons of the keybo
22. tes the different states of the device i gi amp t 2 OUT This connector supplies the modulated channel according to the na selected standard in the module and mixes it with all the signals that it receives throught the MIX connector 3 MIX Input of mixing of the module Be 6 4 LNC IN To connect to the LNC or to the LOOP OUT output of the previous module 5 LOOP OUT To connect to the ANT IN input of the next module 6 RS 232 Ethernet connector to cascade modules with the telecontrol unit with the RJ45 RJ45 cable provided 7 HPR 100 Ethernet connector to make the programming with the programmer 8 DC connectors It has two connectors for input output u a f E States of two colored leds 1 Initialization mode Green main application charged Blinking Green Completing the initial sequence at the moment when the module gets initialized the led will turn into one of the states the operating mode Red Phase of initializing the module 2 Operative Mode Green The system is working properly Orange At least one critical event has been recorded in the module The led will only change into green when the registration of events has been read by the programmer Red Error or alert detected in the running of the device the led will be on only as long as the error alert is present Once the error or the alert disappears the led will change into orange because the error alert is stored in the regis
23. tration of events 3 Programming mode When the module detects an external programmer the led will blink in the next sequence green orange red Once you leave the programming mode the led will turn into the corresponding operating mode 2 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 Stages of transmodulator HSTT 100 Input DVB S QPSK 950 MHz 2150 MHz Selection of a tuned satellite transponder y Transmodulation Sennco Seneca SERVICES Semmco 3 FTA FILTERING Seomce 4 s j Semmco B Bores FTA The tuned channels of the transponder are modulated according to the DVB T rules If the transponder has encoded channels the final user will need a receiver with Cl subscriber card or an encrypted channels receiver hA Out DVB T COFDM 47 MHZ 862 MHZ Configuration of the channels and output parameters 1 4 Programming HSTT 100 has two ethernet connectors In order to make the programming of the module you have to connect the corresponding programmer to HPR 100 connector You can make the programming through the HPR 100 programmer and also through the MDX and MDL field strength meter 1 4 1 Programming modes as they are interconnected with each other through the RJ 45 cable supplied with each unit 3 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 1 4 2 Programming Below you will find the steps to follow in order to make the pr
24. ware version etc Global Update It allows carrying out the update of all the modules that are interconnected at the same time LCN The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes Note If in the existing installation there are already services that have LNC system you will have to configure the position of the module services in order to avoid conflicts with other net services 13 HSTT 100 version_en_1 1 ANKARO User s manual HSTT 100 1 0 Accessories and example of installation Example of installation Installation that consist of 6 HSTT 100 and that will allow tuning channels up to 6 different transponders and to distribute them through a TV network in DVB T The distributed channels need a terrestrial receiver in order to be decoded Ke E Note In order to guarantee the right running of the different equipments of the installation we recommend you to provide the inputs and outputs which are not used with a 75Q load OUT Accessories
Download Pdf Manuals
Related Search