Content
Contents
1. 1 LNB IN 13 18V 500mA Max Connect the Satellite Dish LNB 2 LOOP OUT Output the Dish LNB IN signal 3 RF IN Connect to the antenna of TV to Aerial IN 4 RF OUT Connect to conventional TV 5 AUDIO VIDEO Connect to Audio Video of TV 6 0 12V Supply 12V DC to other apparatus 7 RS232 Connect to serial port of PC for software upgrade 8 Electric Inlet Lead Mains 90 240V AC Auto selectable 50 60Hz Make sure to check the power spec 9 Power AC Power Switch 10 S PDIF Output for connection to a digital amplifier 11 TV SCART VCR SCART Connect to TV set or VCR with Scart cables Kj 2 3 Remote Control Unit RCU You can control this receiver by this remote controller with full function 1 POWER Switch the receiver on or set it to standby mode 2 MUTE Turn the sound On Off 3 NUMERIC KEY 0 9 Change program or input number 4 RECALL Move to the previous viewed channel 5 INFO Show the information of the current channel press EXIT button to exit this menu 6 MENU Activate main menu or exit to live channel 7 EXIT Exit current menu step by step 8 CH Change program 9 VOL Change volume in viewing mode 10 OK Confirm the highlighted menu item Open the program list 11 SAT Show the scanned satellite list 12 FAV Display favorite channel list 13 TV RADIO Switch between TV and RADIO 14 PGUP PGDN Page up down on menu 15 EPG Electronic Program Guide Show the TV Radio2. Additional Information User Friendly OSD Menu with Full Function 256 Colors Graphic User Interface Multi Language Menu English Italian French Spanish Germany Turkish Arabic Russian Persian 7 Days EPG Electronic Program Guide for On Screen Channel Information MP multi picture PIP picture in picture REC short record 10 seconds Super fast 800 pages OSDTeletext Supported and VBI Teletext Inserted Favorite Channel and Parent Lock Function Storing 6000 Channels ZOOM function Ki 1 2 Accessories User manual Remote Control Unit A N Cable Batteries User Manual AIN Cable Battery Remote control Figure 1 Accessories POWER Digital Satellite Receiver 2 Basic Function 2 1 Front Panel 1 Power Button The POWER button is used to turn the power on or to make it on Standby Mode 2 Up Down Button Change channel in viewing mode and move the cursor up down in menu mode 3 Left Right Buttont Increase decrease the volume in viewing mode and change settings in menu mode 4 OK Button Activate the highlighted sub menu in menu mode and activate the channel list in viewing mode 5 MENU Button Activate the main menu in viewing mode or exit all menu 6 Display 4 digi 7 segment 4 digi displays channel information In Standby mode the 7 segment displays local time 7T Power LED Power indicator 8 Signal LED Signal Indicator 2 2 Rear Panel
3. Content eC B 2 1 Reference 1 1 General Features ccc ccc ccc ccc cccccccccccceccccccceccccccecsenencceseesuesueauesnecnees 3 1 2 Accessories ft 4 2 Basic Function 2 1 Front Panel ENST 5 22 WAGON DIR E M ME ME 6 2 3 Remote Control Unit sessesse RR Immer reris 7 3 Installation and Connection 3 1 Connecting to TV amp VOR esee nennen nennen 9 3 2 Connecting to Dish EIND ier eus 10 4 Installation and Operation 4 1 Menu NECIS Me T 12 4 2 Other Useful Information cseseRHR Imm Imm 21 5 Additional Information 9 1 Problem SONING 26 5 2 Technical Specification rss 21 Da Mend Screen ST 28 oA GOSSA 29 Rk Safety Precaution This STB has been designed and manufactured to satisfy the international safety standards Please read the following safety precautions carefully before operating this receiver u Main Supply Before operating please check the units operating voltage is 90 240V AC 50 60Hz u Overload Do not overload a wall outlet extension cord or adapter neither use damaged power cord or touch it with wet hand as this may result in electric shock u Liquid The receiver shall not be exposed to dripping or splashing water and that no objects f
4. NFO kip Channel List OK In viewing mode press OK FAV button and you will get this window a Favor Group Press RED key go to this menu OK to set favorite And press lt P gt to Favor Group list to change current FAV b Channel Edit Press GREEN key go to this menu You can Press RED GREEN BLUE key to Lock Move Rename the channel Also you can press YELLOW key to add new channel c delete Press YELLOW key go to this menu You can Press RED GREEN YELLOW key to sign delete channel one by one or by transponder or by satellite b Channel mode Press BLUE key In this menu you can select the mode you channel list AUDIO In viewing mode press AUDIO button and you Will get this window You can set the Audio mode here v SAT Press SAT button on the remote control you will get this menu which contains the satellites you searched and stored press A W to switch between satellites you searched all channels will be listed under that satellite you selected kip y oe TXT Press the TEXT button and you will get a window to view the teletext contents if the teletext is transmitted in the channel The Teletext content is watchable by OSD even your TV does not support the Teletext PAUSE Freeze the picture RECALL Press recall button you will get the viewing history of last 16 P100 100 DWtoxt 08 03 07 UT 06 14 AUS DER MITTE EUROPAS DW TV E 06 30 In Focu
5. Rk You can play the game in this sub menu Press UP DOWNA V and OK button A Calendar This is the calendar and it will give you the convenience to check the date of your day B Tetris You can see play Tetris on the screen Press RIGHT LEFT lt gt UP DOWNA V to play C Sokoban You can see play sokoban on the screen Press RIGHT LEFT lt gt UP DOWNA V to play D Snake You can see play Snake on the screen Press RIGHT LEFT lt gt UP DOWNA V to play D Mine sweeper You can see play Snake on the screen Do follow as bottom help 3 Ei 1 j E Slot machine You can see play Slot Machine on the screen Do follow as bottom help F Numeric puzzle You can see play Numeric puzzle on the screen Press RIGHT LEFT lt gt UP DOWNA Y to play NR 23 G matching picture You can see play matching picture on the screen R 4 2 Other Useful Information This will guide you on how to use general info while watching TV program or listening Radio program General Information In the viewing mode when you press INFO button to view the detailed program info Program Guide Press EPG button on remote control you can get the electronic program guide if applicable PressA W and press GREEN key to show the electronic program guide of the selected channel You can get the detailed information about that program by pressing I
6. allation Edit Channel System also you can change the password the default password is 0000 D System information This menu show some information about the product such as Product Name Software Ver Loader Ver and so on E Time Setup When you Enable this option and press Ok you will get this window to setup time at GMT on item if select on you can go to the second item to change GMT offset which you want Or you select off GMT You can go to the third item to input your local time F Timer Here you can set your favorite channel to begin broadcasting at future time you set including both TV and Radio you can add edit and delete the event you set ud In this menu you can setup Antenna and Search channels And Reset the system A Antenna Setup Press right button on RCU and move to the antenna setting here to setup the correct LNB frequency switch Type None port 1 port 4 burst A burst B Auto kip 7 Motor If you connect receiver to DiSEqC1 2 or DiSEqC1 3 antenna set motorized system to DiSEqC1 2 or USALS Here press OK button to enter motor system Position Auto W E Press gt button the dish will be motorized to East West continuously it will stop until it find the best signal Move Dish Push gt button the dish will be motorized to East West step by step until you find the best signal showed on the signal bar Fine Tuning Set the moving step Mo
7. illed with liquids such as base shall be placed on the apparatus u Ventilation Keep the slots on top of the receiver uncover to allow sufficient airflow to the unit Do not put the receiver on soft furnishings or carpets Do not expose the receiver to direct light or do not place it near a heater or in humid conditions Do not stack other electronic equipments on top of the receiver u Cleaning Plug out the receiver from the wall outlet before cleaning Clean the receiver by a soft cloth or mild solution of washing up liquid no solvents u Connection Disconnect the receiver from the mains when you connect it to satellite LNB or disconnect it from LNB Failure would possibily cause damage to the LNB u Location Put the receiver indoor in order to avoid lightening raining or sunlight u Uncover Do not remove the cover to reduce the risk of electric shock Contact qualified and licensed service personnel to repair the receiver or contact your dealer 1 Reference 1 1 General Features MPEG 2 amp Fully DVB Compliant MPEG 2 Video MP ML MPEG 1 Audio Layer1 Layer2 PLL RF Modulator UHF 21 69 with PAL B G 1 D K Multi LNB Control by DiSEqC 1 0 1 2 1 3 LNB Power 13 18V Max 500mA SCPC MCPC Receivable from C Ku Band Satellites Digital Tuner with Loop Through 2 Scarts for TV and VCR PAL NTSC Conversion Variable Aspect Ratio 4 3 16 9 for TV 4 digi 7 segment LED Display RS232 Port for Updating software and
8. nel Scan Network SAT Name Tp Edit Scan Sat Frequenoy Polarisation Symbol rate search Type Radio Channel Scan Network Tp Delete Factory Reset YES NO 33 Calendar Tetris Sokoban Snake Mine sweeper Slot machine Numeric puzzle Matching picture 5 4 Glossary Antenna A device that collects and radiates electromagnetic waves Includes a satellite dish and a broadband antenna DiSEqC DiSEqC Digital Satellite Equipment Control system it is a communication bus between satellite receivers and peripheral equipment using only the existing coaxial cable DVB The Digital Video Broadcast group was created to establish a technical framework for the introduction of digital video broadcasting systems LNB low noise block converter or LNBF An electronic unit mounted on the satellite dish It receives the signals reflected by the dish and converts them to signals that can be used by the digital satellite receiver GHz The prefix giga means milliard and Hertz means cycles per second Signals in the GHz range are often called microwaves MHz The prefix mega means million and Hertz means cycles per second MPEG Moving Picture Experts Group Established by the International Standards Organization to provide the basis for a picture coding and compression system Forward Error Correction FEC A system of error control for data transmission kip S PID Packet Identifier A set of
9. numbers that identifies transport stream packets containing data from a single data stream Polarization Polarization allows several programs to be fit into the same frequency band The signals from a satellite are transmitted either with linear vertical or horizontal polarization or circular right or left polarization QPSK Quaternary Phase Shift Keying Phase shift keying in which four different phase angles are used Transponder An automatic device that receives amplifies and retransmits a signal on a different frequency Symbol rate Speed of the digital transmission RF Radio frequency known as HF in some countries Scrambled TV programs Some TV programs are transmitted in scrambled form SERIAL RS 232 A serial communication standard data port RCA Coaxial connector used to connect the receiver to an external amplifier 35
10. ode You have forgotten Contact the dealer or Service your password Provider They will help you set it up again Poor picture quality Low LNB power or signal Change the LNB power to 14V 19V or less channels in loss in cable in Antenna setup menu scanning 5 2 Technical Specification Tuner amp Demodulator Horizontal 18 V 19V 5 Current 500 mA Max Overload Protection MPEG Transport Stream A N and Data In Out Connector TV SCART RF Modulator Power Supply Physical Specification Size W x H x D 280 x 55 x 285 mm Weight Net Around 2 0 kg Operating Temp 0 C to 40 C Storage Temp 40 C to 65 C Menu Navigator System Configuration Tv Output Parental Control System information Antenna Setup Satellite Scan Tp Edit Scan Factory Reset Timer Setup Timer Kj System Configuration Menu Language Audio Language OSD Time Out Transparency Channel Option Auto Power Ty Output TV Type Screen Type RF Mode RF Channel Parental Control Password Lock Lock Channel Edit Lock Installation Lock System Setting New Password Verify Password System information Product Name Soflware Ver Loader Ver Channel Used Satellite Used Tp Used Timer Setup GMT On GMT Offset Current time Current Date Timer Add E dit Delete 5 3 Menu Screen Structure Antenna Setup Delete Start Scan Add Rename Satellite Scan Search Type Radio Chan
11. program guide 16 ZOOM Picture Zooming function 17 AUDIO Select or change the Audio 18 TXT Show the teletext content if teletext is transmitted 19 PAUSE Freeze the picture 20 SLEEP Sleep timer function 21 SUB Subtitle 22 FIND Find Channel by channel name 23 Picture Picture 24 REC Record and playback 10 seconds 25 M P Multi picture Kj 3 Installation and Connection The following diagram shows you the connections among receiver TV VCR LNB and other equipment please read this first if you are not sure about the connection and it will guide you to the correct connection 3 1 Connecting to TV amp VCR 1 Connect the TV antenna to AERIALIN 2 Connect the RF IN of TV to RF OUT 3 Connect the Video and Audio of TV to the Video and Audio Connect Red and White connector to Audio R and Audio L and Yellow into Video port respectively 4 Go to section 3 2 Connecting to Dish then connect your dish TV Figure 5 Connecting to TV amp VCR 3 2 Connecting to Dish LNB You can connect one fixed dish LNB directly to the LNB IN or connect at least two dish LNB by DiSEqC Switch you can also connect to HH mount dish LNB 1 Connect the TV antenna to AERIAL IN 2 Connect the RF IN of VCR to RF OUT with RF cable 3 Connect the RF OUT of VCR to the RF IN of TV 4 Connect the Video and Audio of TV to the Video and Audio Connect Red and White connector
12. s Coffoo the Mighty Boan Merkel will EU zum Vorreiter beim Klimaschutz machen NEWSTICKER INDEX 101 Quelle WWW DW WORLD DE ZOOM Picture Zooming function TV RADIO In this window you can select channel and delete undelete channel rename channel sort channel move channel lock channel skip channel set favor channel Select Ghannel Manager you will get this window M P Multi picture In viewing mode press M P you will get the multi picture selection select one and press ok multi picture will be displayed Move up down left right to select channel press M P again to get that selected channel pop out and it is living press ok to display it in full screen or exit to select other channel 29 FIND In this menu you can Find Channel by channel name PIP picture in picture You can press PIP to enter PIP mode then press F1 to exchange between big picture and small picture Press PGUP PGDN to change the channel of small picture by left right up and down button you can move the position of small picture Also press EXIT key to exit PIP mode F2 Subtitle Showing Subtitle information if the channels contains REC Short Record You can press REC to enter Short Record mode then press RECALL to play back Then press EXIT key to exit Short Record mode X 5 Additional Information 5 1 Problem Solving You might meet abnormal working of this STB wi
13. th various reasons check the following which may help you LED on the front Mains supply cable is not Check if the mains supply cable is panel fail to light connected plugged into the power socket up is not lit No picture or sound Satellite dish is not aiming to Adjust the dish Check the signal satellite accurately strength indicator in one of the signal or weak signal The channel search submenus Check LNB is faulty The cable is the cable connections LNB and faulty other equipment connected to LNB amp receiver or adjust dish Replace the LNB Replace the cable Bad picture blocking Satellite dish is not aiming to Adjust the dish Connect a error the satellite accurately attenuator to LNB input Change to a Signal too strong Satellite larger dish Change LNB with lower dish is too small LNB noise noise factor Replace the LNB factor too high The LNB is faulty No startup menu on The system is connected by Switch the TV to the appropriate AV screen after turning SCART cables and the TV is input on STB for the first notin AV EXT mode time The remote control Battery exhausted Remote Change the batteries both Aim the is not working control is not aimed correctly remote control at the STB Check STB is in standby mode that nothing blocks the front panel Check if LED indicator on the front panel is showing the time press the power button to switch off standby m
14. to Audio R and Audio L and Yellow into Video port respectively m COMPUTER Figure 6 Connecting to Dish LNB kip LNB 2 LNB3 w L LNB 1 LNB 4 Figure 7 Connecting to Dish LNB x 4 Installation and Operation Ater connecting the receiver to other required equipment turn on the receiver there should be no channel information available at the first startup you need to follow the procedure to setup your receiver to search the channel 4 1 Menu Guide During the installation there is a short information showed at the bottom of the menu screen which will guide you to set up after finishing installation you can enjoy watching TV or listening Radio Main Menu Press MENU button to activate main menu which consists of 9 7 Use RIGHT LEFT 4 button to select your subject and press OK to confirm your selection and enter that sub menu press EXIT button you can return to the previous menu al Here you can setup System Configuration TV Output Parental Control System information Time Setup and Timer kip A System Configuration Select System Configuration and press OK you will get this window Here you can change Menu Language Audio Language OSD Time Out Transparency Channel Option and Auto Power B TV Output You can setup TV Type as PAL or NTSC Screen Type as 4 3 or 16 9 or other format and HF C Parental Control You can select if need the password or not for Inst
15. ve Step Move East or West step by step Limit Set Disable or enable West limit or East limit Store Position Save the current position you searched Go to Position Press OK button to move the dish to the stored position Go to Reference Press OK button to move the dish to 0 position Press EXIT after setup and you can search channel now kip i7 77 USALS Setup If you use USALS Press RED key to setup you Local parameters A 1 Delete Press RED key to delete the selected sat then will show a window ask you to confirm Select OK confirm and EXIT to abort this action A 2 Add Press Yellow key to add new satellite A 3 Rename Press BLUE key to rename current satellite name kip io A 4 Start Scan Press GREEN key to go to Satellite Scan menu to search channels B Satellite Scan In this menu you can set scan mode and which type of channels you want to search by RIGHT LEFT lt gt UP DOWN A V Then Press OK to start search B 1 Search Channel In this menu you can see the search Result During searching the TV channel and Radio channel will be listed separately C Tp Edit Scan Here you can Edit the transponder and scan channel 7 Tp Delete If you want to delete tp go to the Tp delete item and press OK Button D Factory Reset Press OK to Reset the STB system to load default setting and channel list p r EE A CA Menu This message will appear after you insert the CA Card
Download Pdf Manuals
Related Search