ATP-02(C) Gebruikershandleiding / Manual
Contents
1. 50 to 250 C Certified range in accordance with EN12830 50 to 50 C Resolution 0 1 C F for F is in interval 130 to 100 F resolution 1 F Accuracy of temperature inputs without probes valid both for inputs Pt1000 and Ni1000 0 2 C in full range Accuracy of the recorder with connected temperature probe is defined by the above input accuracy and accuracy of the used probe Temperature unit C or F Maximum length of the probe cable 20 m Type of connectable probe with RTD sensor Pt1000 3850 ppm or Ni1000 6180 ppm Recommended probe Pt1000 TEPW 102M probe with protection IP67 range 30 to 80 Response time for probe PT1000 TEPW 102M t90 lt 150 with temperature step 20 C air flow approximately 1 m s Connection of temperature probe to terminals with two wire shielded cable Connection of switches to binary channels to terminals two wire shielded cable Maximum conductor area connectable to terminals 2 5 mm2 Maximum length of probe cable 20 m Current through binary channel switches cca 0 3 mA Interval of measurement alarm evaluation MIN MAX memory update and refresh of measured values on the display 5 s Logging interval of measured values to memory 1 min to 60 min 10 selections Memory capacity 102 400 records each channel both temperature channels enabled 172 032 records if only one temperature channel is enabled Specified number of records is maximum possible and can be achieved only if record2. ATP 02 en ATP 02C User manual ATAL B V Amp restraat 35 37 NL 1446 TR PURMEREND Postbus 783 NL 1440 AT PURMEREND T 31 0299 630 610 F 31 0299 630 611 E info atal nl I www atal nl CONTENT 1 0 B si recorder RAS ne aS 3 2 0 Fixed installation Of TECOLIEL A means E E E EEEa 3 3 0 Recorder configuration before operation ss 6 4 0 Using Of SSI sennou ro aiani E A T AERE ES 7 4 1 Recorder Controls E E saan E 7 4 2 Basi cdisplay Adele teen cadens ai ta dt toast nent tree 7 4 3 Printout of recorded values on built in printer ee eee esse cee ceeeeeeeeeeneecaeenaeeneeeennees 7 4 3 1 Print ut of the Delivery TIGRE a tenti ees 7 4 3 2 Printout of recorded VAI dd tenons 8 4 3 2 1 Selection of values for PEO secs de un ns ry tutedaad 8 43 22 Start of print of recorded values iis sciescacccssansvcsscsvavestassacdesacedvad eesiecsesasvtsasdaadseuvancevenss 8 4 3 2 3 Data contained in numerical table of values Journey Ticket eeeeeeeeeeeeeeeee 9 4 3 2 4 Data contained in Graph Ticket for temperature channels only 10 4 3 2 5 Stopping of printout of Journey or Graph Ticket 10 4 3 3 Paper replacement in built in DM assistent 11 4 4 Configuration of recorder from built in keyboard 12 AAT Main menU RE EPP EE ET 12 44 2 M nt 6 0 PAIE Sn deniers aulendnn due 16 5 0 Functions of the recorder connected to the PC 21 5 1 Installation of program for personal computer 21 5 2 Recorder configuration
3. Graph can be useful for graphic presentation of longer time sections of temperature with simple evaluation of exceeded alarm limits Graph is printed lengthwise always channel by channel Y axis scale must be preset suitably in accordance with expected temperature values at monitored room The scale is set for each channel individually 0 0 Ms fat ene ee et ee eee 1 1 1 1 0 1 1 L I 1 1 0 I t I r r 5 0 E E E cee eee EPES BAPE PEO PERPE PE E E en eee Aes re et a RS 19 00 01 00 07 00 13 00 19 00 01 00 07 00 13 00 19 00 01 00 07 00 13 00 01 08 02 08 02 08 02 08 02 08 03 08 03 08 03 08 03 08 04 08 04 08 04 08 2008 2008 2008 2008 2008 2008 2008 2008 2008 2008 2008 2008 15 0 Time values are on the X axis One segment always represents six recorded values Figure shows an example of record with 60 minute interval Vertical dashed line is one time segment and refers to nearer i e left time value If recorded values are outside of the selected Y axis scale of the graph curve not be printed at this area Alarm limits of the currently printed channel are presented by two continuous lines without any description alarm limit values are printed out at the end of the header If the curve exceeds the alarm line recorded values are outside of the set limits If alarm limits are set outside of the graph range alarm lines are no
4. 7 9 00 00 15 7 9 30 00 15 7 10 00 00 15 7 10 30 00 15 7 11 00 00 15 7 5 2 C 5 2 C 5 2 C lt values recorded in recorder memory JourneyStartTime adjusted to 4 00 Journey Duration is indicated in bold adjusted to 6 hours values to be printed are indicated by frame A prints towards older values print start if history record printout is not set newest recorded value from memory is here Example 2 setting of Journey Duration is irrelevant 3 00 00 15 7 3 30 00 15 7 4 00 00 15 7 4 30 00 15 7 5 00 00 15 7 5 30 00 15 7 6 00 00 15 7 6 30 00 15 7 7 00 00 15 7 7 30 00 15 7 8 00 00 15 7 8 30 00 15 7 9 00 00 15 7 9 30 00 15 7 10 00 00 15 7 10 30 00 15 7 11 00 00 15 7 5 2 C 5 2 C 5 2 C 5 2 C 5 2 C 5 2 C 5 2 C 5 2 C 5 2 C 5 2 C values recorded in recorder memory Journey Duration is indicated in bold adjusted to 6 hours journey start time adjusted on 8 00 values to be printed are indicated by frame 4 prints towards older values print start if history record printout is not set newest recorded value from memory is here ATAI MAG 13 3 0 Journey End Date Function served for printout of older history values in memory Defines day required values will be printed out Function is available for print of older values stored in memory Use button CHANGE and then buttons A V or gt for setting itself Active function it is possible
5. TEPW 102M the conductor area of the cable wires is 0 14mm After correct entering of parameters store new setting to the recorder by clicking Write to logger button 5 3 Reading of recorded data For recorded data download from recorder to the computer connect recorder to the computer by means of the communication cable and run user program Select menu item File Download from device confirm offered file name and click to Store It is also possible here to enter suitable description of file with recorded data and select if memory of recorder after data transfer will be erased or recorded data remains in memory Data transfer to the computer follows After finishing table of recorded values appears Analogous way enables to open archived recorded data file in the computer anytime Use menu item File From disk and select required file ATAI LAG 21 Hyphens instead of measured values in the table indicate values outside of the measuring recorder range optionally not connected temperature probe If min max average record is not selected columns Min and Max for both channels in the table are empty min and max values are not recorded Often the graphic presentation of recorded data can be more suitable Graphs are accessible after data download from the recorder or computer hard disk by selection of menu View Graph 54 Erasing of recorded data Recorded data in recorder can be erased by means of the computer by selection Configura
6. as with temperature channels see setting 6 2 3 6 above 6 4 5 7 Alarm Active If If alarm of proper binary channel is in use it is necessary to set which binary state ON or OFF will activate the alarm Set this after pressing button CHANGE Switch between values ON and OFF by means of buttons A or V If binary state description was entered before corresponding description is displayed for easy orientation when switching states ON and OFF Save new setting to the recorder by button STORE or leave the mode without saving by button CANCEL ATAI AHH 19 4 4 3 Structure of menu 1 0 Journey Duration xx Hour Disable 1 25Shours i e 10 6 days controlled by buttons TIME and DISABL 2 0 JourneyStartTime xx 00 Hour Disable 0 23hours controlled by buttons TIME and DISABL 3 0 Journey End Date xx xx 20xx Today 1 1 2000 31 12 2099 controlled by buttons DATE and TODAY 4 0 Journey End Time xx 00 Hour From Now 0 23hours activated analogically with previous selection 5 0 Info On Seting Submenu only viewing of adjusted parameters 6 0 ParameterSetting Submenu protected by PIN stops the record after completion of setting resets the recorder 7 0 Illuminat Level 0 100 8 0 Language Select 15 selections maximum 5 1 General Setting 5 1 1 Logging Interval Alarm Audio 5 1 2 MemoryOccupation Logging Mode 5 13 Temperature Unit Logger Type 5 14 Logger Location Header Text 5 1 5 Ser Num FW vers Menu
7. button STORE to store selected unit to recorder or button CANCEL to end unit selection without storing 6 1 8 Logging mode Enables to select by means of buttons A or V one of three available logging modes actual when actually measured value is recorded at the moment of logging interval average when average value of temperature measured during adjusted logging interval is recorded Temperature is measured in fixed interval 5 s min max average when average value of temperature measured during adjusted logging interval same as above accompanied by minimum and maximum temperature in logging interval Recorded min and max values are available after data download to computer Printout on built in printer is not enabled Use button STORE to store selected logging mode to recorder or button CANCEL to end logging mode selection without storing 6 1 9 PIN Change This menu item enables user to change anytime four digit PIN code Edited digit is indicated from above and below by arrows and it is possible to change it by buttons A or V Other digits are hidden replaced by symbol asterisk Shift to another edited digit by button D gt Use button STORE to store PIN to recorder or button CANCEL to end PIN change without storing Remember new PIN well there is no universal code to unblock the recorder 6 2 6 3 Setting of channel 1 or channel 2 Following parameters concern each channel and can be adjusted separately for each channel Ad
8. from memory erasing was not interrupted by new setting and if logging mode of actual or average values is selected In logging mode average min max values number of records is approximately 3 times lower If binary channels are enabled then every change on binary input causes drop of remaining memory capacity approximately of 0 6 record both temperature channels enabled or of 1 record if only one temperature channel is enabled Communication with computer USB port or RS232 Real time clock adjustable from the computer integrated calendar including leap years Accuracy of internal clock lt 200 ppm i e 0 02 17 28 s in 24 h Consumption without display illumination not printing 100mW during print 8W Protection IP20 Operating conditions Power external source 9 to 32 V dc and back up battery of internal clock 3V CR2032 Power circuit protection fuse T3A Operating temperature range of recorder 30 to 65 C at temperature below 20 C display must not be readable Operating temperature range of built in printer 20 to 50 C Operating humidity range of the recorder 5 to 85 RH without condensation External characteristics in accordance with EN33 2000 3 normal with the specifications NM AEl AN1 ARI BEI Working position horizontally or vertically Mounting of recorder use self cutting screws with diameter 4 mm suitable lengths ATAI AAG 23 Limit conditions Power external source 36 to 36 V dc Limit temperature range
9. gear of printer drive and lid can be opened easily Unwind several centimeters of paper from new role and insert it to paper container thermo sensitive layer outside Unwound paper end must stick out from container Press strongly printer lid to snap audibly to container lock Now it is possible to tear off printed out paper over tear edge of the printer and the lid stays closed Printer is ready to operation 11 44 Configuration of recorder from built in keyboard 44 1 Main menu From main menu are directly available functions of print setting information on record parameters setting setting of LCD illumination level and menu language selection For setting of all other parameters it is necessary to enter 4 digit PIN code Manufacture PIN code is 5555 user can change it anytime Move between menu items by means of buttons A or V Go back to basic display button by means of button Escape Items of main menu 1 0 Journey Duration 2 0 JourneyStartTime 3 0 Journey End Date 4 0 Journey End Time 5 0 Info On Setting 6 0 ParameterSeting 7 0 Illuminat Level 8 0 Language Select 1 0 Journey Duration Defines time period of recorded values to be printed Set journey duration in whole hours at range from 1 to 255 h which represents 10 6 days of printed record in maximum Use button CHANGE and then buttons A V or gt for setting itself Active function it is possible to disable by button DISABL If function is disabled print o
10. lost even in disconnection recorder from power Record of actual or average values is user selectable including minimum and maximum temperatures If memory is fulfilled oldest recorded values are overwritten with new values Setting and control of recorder is performed from keyboard recorder or by means of computer In both cases setting can be protected by password Recorder is equipped alarm function I e each 5 seconds independently on adjusted logging interval temperature is measured from both external probes measured value from each channel is compared with two adjustable limits for each channel Limit exceeding is indicated on the LCD display by the red LED and acoustically Alarm evaluation is possible to enable or disable for each channel including signals from binary inputs Audible indication can be also enabled or disabled Measured values recorded in recorder memory can be printed out on built in printer as table or graphs or transferred means of USB communication cable to personal computer for evaluation Also Delivery Ticket with current temperature value s and header can be printed Recorder conforms EN 12830 requirements conditions for class 1 accuracy and is suitable for temperature record during storing S and transport T of food in climate environment code A B If recorder is used during transport it must be installed in cabin of the vehicle 2 0 Fixed installation of recorder Recorder is delivered with installed batt
11. max Here it is possible to preset maximum of the Y axis scale of the proper channel in analogical way as described above 6 4 5 2 StateOFF Dscrptn Here it is possible to enter description of binary state OFF i e switch opened of proper binary channel in 8 characters length Description will be visible on display and in header of each printout from built in printer It is possible to edit text after pressing button CHANGE Edited ATAI 18 AAG character is marked from above and below by arrows and 1s editable in alphabetical order by buttons A V Optionally it is possible to switch easily between lower and upper case letters or symbols by means of button 1 A a Space is the first character of symbols and follows the last character of lower case alphabet z Digits are the part of symbols Move to another edited character in text string by button gt Standard offer STORE for saving edited text or CANCEL to exit editing without saving is available after pressing button NEXT 6 4 5 3 State ON Dscrptn Here it is possible to enter description of binary state ON i e switch closed of proper binary channel The procedure is identical with above description of state OFF 6 4 5 4 Alarm Delay The procedure is identical as with temperature channels see setting 6 2 3 4 above 6 4 5 5 Alarm ON OFF The procedure is identical as with temperature channels see setting 6 2 3 5 above 6 4 5 6 Channel Logging The procedure is identical
12. measuring range or value sensed with disconnected optionally damaged temperature probe If some channel is disabled for record by the user dots are printed out instead of values of proper channel Recorded states of binary inputs are always indicated on the printout as ON or OFF independently on the adjusted description of each state Assignment of ON OFF states to descriptions is printed out in the record header printed lastly Interruption of record caused by configuration of recorder from keyboard or from computer is indicated in printout line with beginning time of record interruption and by reading nterrupted Keyb or Interrupted PC 20 04 2008 Chl Ch2 Ch3 Ch4 value recorded in recorder memory 3 00 00 15 7 5 2 C OFF OFF 3 30 00 16 1 5 1 C OFF OFF 4 00 00 16 0 5 5 C OFF OFF symbol indicates record of average values 4 30 00 15 6 5 4 C OFF OFF 5 00 00 5 2 C OFF OFF dots indicate disabled temperature channel 5 27 15 Interrupted PC record interruption logger configuration from PC 6 00 00 14 2 C OFFOFF hyphens indicate value out of the range or no 6 12 05 change in binary record 6 30 00 8 5 3 C OFF ON lt record of actual values without symbol 6 4 2 C OFF ON A prints towards older values i lt print start if history record printout is not set newest recorded value from memory is here ATAI ATAL 9 4 3 2 4 Data contained in Graph Ticket for temperature channels only
13. of alarm enable or disable audible alarm indication if suitable enter text description of each channel and location of recorder if suitable enter desired contain of printout header if necessary avoid unauthorized setting of recorder by entering password when configuring from the PC or PIN code when configuring from the recorder keyboard Recorder is not equipped with power switch After connection to power short initialization is performed and then recorder immediately continuously measures and records Interval between two subsequent measurements is specified by the user The interval can be adjusted from to 60 minutes Memorizing of the first value is synchronized with the internal real time clock so the record is performed at sharp multiples of minutes hours and days E g after starting the record with the 15 minute interval the first value is not stored immediately but after the internal clock gets the status of a quarter a half or a whole hour Warning Connect external probe only to the switched OFF recorder In opposite case incorrect measurement can be recorded to the memory during connecting the probe During setting of record parameters from recorder keyboard or from the computer record is stopped till the setting mode is left If recorder stays in setting mode 5 minutes and no key is pressed and no command from the computer is received recorder automatically ends up setting mode and record continues If recorder is power
14. of recorder 30 to 70 C Storing conditions temperature 40 to 85 C humidity 0 to 85 RH without condensation Dimensions without metal holders 175 x 124 x 51 mm Weight without probes approximately 570 g Material of the case ABS Paper for printer width 57 mm length 10 m i e approximately 3400 printed lines 7 2 Recorder passed through tests of electromagnetic compatibility EMC Device conforms in accordance with EN 61326 1 these norms radiation EN 55011 Class B immunity EN 61000 4 2 levels 4 8 kV Class A EN 61000 4 3 intensity of electric field 3 V m Class A EN 61000 4 4 levels 1 0 5 kV Class A EN 61000 4 6 intensity of electric field 3 V m Class A 7 3 Technical support and service of the recorder Technical support and service is ensured by the distributor of this recorder ATAI 24 IAG
15. or disabled by means of buttons A or V Use button STORE to store alarm evaluation to recorder or button CANCEL to end alarm evaluation adjustment without storing 6 2 3 6 Channel Record Enables to disable proper channel for record e g if temperature probe is permanently disconnected Capacity of recorder memory is then available for another channel At least one temperature channel must be enabled for record It is not allowed to disable both channels at the same time Change the state of channel logging after pressing button CHANGE Select value enabled or disabled by means of buttons A or V Use button STORE to store channel logging to recorder or button CANCEL to end channel logging adjustment without storing 6 2 3 7 Graph Y axis min It is useful for graph print to preset graph Y axis scale in accordance with expected temperature values at monitored room Set minimum of the Y axis scale of the proper channel after pressing of the CHANGE button Value is adjustable from the range 130 to 500 temperature unit is defined by set temperature unit in general setting After temperature unit change the set value of the Y axis scale remains the same Edited digit of scale value is marked by arrows from below and above and can be changed by A or V buttons Shift to next edited digit by button gt Press button STORE to save new Y axis scale value to recorder Press button CANCEL to leave without saving changes 6 2 3 8 Graph Y axis
16. to disable by button TODAY i e it prints always from actual date and time to the history Function it is possible to use in parallel with functions Journey Duration and JourneyStartTime Function Journey End Date is directly related to function Journey End Time which precisely defines time of print in selected day 4 0 Journey End Time Defines time of recorded value from which towards older recorded values print will be started This function is usable only for print of older values in memory and is enabled or disabled together with function Journey End Date Disabled function is indicated by reading Today i e prints always from actual date and time to the history Use button CHANGE and then buttons A V or gt for setting itself Function Journey End Time is directly related to function Journey End Date which defines date of print start for selected time Example how menu items for print control Journey Duration Journey Start Time Journey End Date Journey End Time influence the printout of recorded values table YOUR COMPANY Example was made with this setting Journey Duration disabled T PRINT ATP 02C FW 01 40 Journey Start Time 3 00 Ser Num 09970003 Journey End Date Today Location Vehicle BN CC230 Journey End Time From Now Printed 03 04 2009 11 09 Ch1 Frozen section record printout is always ended up by header Ch2 Chilled section 03 04 2009 Chl Ch2 3 00 00 15 7 5 2 C which value is printed as last is influen
17. S232 device e g GSM modem 8 USB socket for PC connection 9 mounting holders ATAI ATAL 5 3 0 Recorder configuration before operation Before first operation it is necessary to set recorder from recorder keyboard or by means of personal computer with installed user software For recorder connection to the computer included USB cable is necessary If recorder setting is performed from the computer recorder is powered via USB interface from computer and no other power source is needed This could be an advantage when recorder configuration is needed before installation itself Before starting the operation it is necessary select language of recorder menu only before first use check optionally set real time in recorder select unit of temperature measurement C F select suitable logging interval select logging mode actual value average value or average value min max check for each channel optionally set by means of computer type of connected temperature probe Pt1000 or N11000 and the cable length correction This setting is necessary for correct measurement and is not enabled from recorder keyboard For details see page 21 e disable channels not to be recorded e g without connected probe e if using alarms set for each temperature channel lower and upper limits and enable alarm if using alarms set for each binary channel state of binary input to activate alarm and enable alarm set for each channel delay
18. Set logging interval by pressing button CHANGE and by selection from preset values by means of buttons A or V Store selected interval by button STORE 6 1 2 Alarm Audio This menu item enables to disable enable audible alarm indication If audible indication is enabled in active alarm state every 10 seconds warning signal sounds Sound is possible to switch OFF temporarily by button AUDIO if new alarm is activated signal sounds again If audible indication is disabled warning signal does not sound 6 1 3 Logger Location Enables to enter description of recorder location with 16 characters Description will be visible on each printout from built in printer Edit text after pressing button CHANGE Edited character je indicated from above and below by arrows and change is enabled in alphabetical order by buttons A V Optionally it is possible to swap between capital letters and lower case letter or symbols by means of button 1 A a Space character is first character of symbols and follows after last character of lower case letters z Digits are part of symbols Shift to another edited character in text string by button Standard offering STORE to store edited text or CANCEL to end editing without storing are available after pressing button NEXT 6 1 4 Header Text Can contain e g your company name and it is printed out always at the first line of the header of the printout of measured values Edit text after pressing button CHANGE Editin
19. Vers PC Driver State 5 2 Setting Of Channel 1 5 2 1 Upper AlarmLimit Lower AlarmLimit 5 2 2 Alarm Delay Alarm ON OFF 5 2 3 Sensor Type Channel Logging 5 3 Setting Of Channel 2 5 3 1 Upper AlarmLimit Lower AlarmLimit 5 3 2 Alarm Delay Alarm ON OFF 5 3 3 Sensor Type Channel Logging 6 1 General Setting 6 1 1 Logging Interval 1 2 3 4 5 10 15 20 30 60 min 6 1 2 Alarm Audio Enable Disabled 6 1 3 Logger Location 16characters max vehicle number driver 6 1 4 Header Text 16characters max e g company name 6 1 5 Set Date 25 09 2008 6 1 6 Set Time 15 11 Hour 6 1 7 Temperature Unit C F 6 1 8 Logging Mode Actual Values Average Interval Min Max Average 6 1 9 PIN Change 6 2 Ch1 Setting 6 2 1 Chan Description 16characters max 6 2 2 Upper AlarmLimit xxx x C F adjustable 130 to 500 6 2 3 Lower AlarmLimit xxx x C F adjustable 130 to 500 6 2 4 Alarm Delay 0 60 min 6 2 5 Alarm ON OFF Enable Disable 6 2 6 Channel Logging Enable Disable 6 2 7 Graph Y axis min xxx x C F adjustable 130 to 500 6 2 8 Graph Y axis max xxx x C F adjustable 130 to 500 6 3 Ch2 Setting 6 3 1 Chan Description 16characters max 6 3 2 Upper AlarmLimit xxx x C F adjustable 130 to 500 6 3 3 Lower AlarmLimit xxx x C F adjustable 130 to 500 6 3 4 Alarm Delay 0 60 min 6 3 5 Alarm ON OFF Enable Disable 6 3 6 Channel Logging Enable Disable 6 3 7 Graph Y axis min xxx x C F adjustable 130 to 500 6 3 8 Graph Y axis max xxx x C F adjusta
20. ble 130 to 500 6 4 Ch3 Setting 6 4 1 Chan Description 16 characters max 6 4 2 StateOFF Dscrptn 8 characters max 6 4 3 State ON Dscrptn 8 characters max 6 4 4 Alarm Delay 0 60 min 6 4 5 Alarm ON OFF Enable Disable 6 4 6 Channel Logging Enable Disable 6 4 7 Alarm Active If ON description OFF description 6 5 Ch4 Setting 6 5 1 All items identical with Ch3 Setting to 6 5 7 ATAI 20 ATAL 5 0 Functions of the recorder connected to the PC 5 1 Installation of program for personal computer Installation program is common for both versions of user program i e basic and optional Installed user program during first run asks installation code if code is entered program runs as optional version If installation code is not entered program se runs in basic version Installation code can be entered anytime later Tick during installation offered selection Install driver for USB adapter valid only for Windows2000 and newer operating systems Older operating systems require driver installation after first recorder connection to the PC Recorder is connected to USB interface of the computer but user SW communicates with recorder by means of the virtual serial port Check if adjusted COM port number in driver properties USB Serial Port is at the range COM1 to COM8 program does not support higher port numbers If needed correct the setting open driver features USB Serial Port by pressing right mouse button on this driver in Devic
21. by means of personal computer 21 5 3 Reading of recorded AA ni annees 21 SA Erasing of r cord d datae nement diner 22 6 0 Replacement of back up BAM eae ee eee 22 7 0 Technical parametetS essre ignei E a E E E Eia 23 7 1 Technical parameters of the recorder 4 ne ie nu 23 7 2 Recorder passed through tests of electromagnetic compatibility EMC 24 7 3 Technical support and service of the T CONer ne mie nina disais 24 ATAI 2 AIAL Manual for use of temperature recorders ATP 02 and ATP 02C 1 0 Basic recorder features ATP 02 economy recorder version Recorder is designed for temperature measurement and record from up to two external temperature probes ATP 02C fully equipped recorder Recorder is designed for temperature measurement and record from up to two external temperature probes and two binary signals from external switches time of event is recorded e g door opened closed Also serial RS232 port is included for connection of e g external GSM modem Notice this manual is common for both recorder models All information in the following text concerning binary inputs i e channels 3 and 4 and serial RS232 interface is valid only for fully equipped recorder ATP 02C Measured temperatures from both channels and actual binary inputs states are displayed on dual line illuminated LCD display and are recorded in adjustable time interval to internal non volatile memory recorded values will not be
22. ced also by 3 30 00 15 7 5 2 C setting of parameter Journey Start Time setting is 4 00 00 15 7 5 2 C relevant only for single day intervals 4 30 00 15 7 5 2 C 5 00 00 15 7 5 2 C 5 30 00 15 7 5 2 C 6 00 00 15 7 5 2 C 6 30 00 15 7 5 2 C number of printed values is influenced also by 7 00 00 15 7 5 2 C setting of parameter Journey Duration can be set 7 30 00 15 7 5 2 C in number of days or in hours 8 00 00 15 7 5 2 C 8 30 00 15 7 5 2 C 9 00 00 15 7 5 2 C A prints towards older values 9 30 00 15 7 5 2 C 10 00 00 15 7 5 2 C 10 30 00 15 7 5 2 C which value is printed as first is influenced only by 11 00 00 15 7 5 2 C setting of parameter Journey End Date and Journey End Time if printout of older records is not set parameter is set to Today and From Now ATAI 14 LAG 5 0 Info On Setting This function enables to view all recorder settings protected by PIN code Move between setting items by buttons V Button NEXT enables quick move between General setting selections Setting of channel and Setting of channel 2 6 0 ParameterSetting Access to this menu item is protected by PIN code If PIN is entered correctly record stops till the end of setting mode If recorder stays in setting mode 5 minutes and no key is pressed and no command from the computer is received recorder automatically ends up setting mode and record continues 7 0 Iluminat Level This function enable
23. e manager and by selection of item Properties Select card Port Settings and press button Advanced on the card and select free port at the range 1 to 8 5 2 Recorder configuration by means of personal computer Before starting the recorder operation it is necessary to set recorder parameters and other functions from the instrument keyboard or by means of the PC program Some of the settings are possible to do only from the PC program Recorder connected to the computer is not necessary to power from external source After connection of the recorder to the computer by means of the included communication cable run installed Program for dataloggers Select menu item Configuration Device setting An info window appears with actual recorder configuration Bookmark Logger setting enables all general settings Bookmark Channels enables setting of channels one by one Bookmark Channels also enables setting of the type of temperature sensor Pt1000 or Nil 000 and Probe cable length correction Both parameters must be correctly set for both channels from the PC program setting from the recorder keyboard is not enabled Incorrect setting causes incorrect temperature measurement Standard sensors of the delivered probes are Pt1000 specified on the probe label For the correction of probe cable length it is necessary to enter probe cable length specified on the probe label and the conductor area of the cable wires For standard probes Pt1000
24. easured value from all channels date and time of recorder internal clock If logging mode of average values b or logging mode of min max average p MinMax are selected also symbols indicating these modes record Hyphens on display indicate values outside of recorder measuring range or values sensed with disconnected optionally damaged temperature probe By pressing buttons A or V it is possible to view actually measured values from each channel including user description of the channel By pressing button MENU recorder goes to mode of viewing items of main menu By button PRINT it is possible to start the printout of recorded values on built in printer The middle button AUDIO is active only if alarm is activated and enables to mute temporarily audible alarm indication In this case audible indication is activated again if new alarm appears Running alarm state is indicated on display by inverse reading ALARM together with information which channel activated the alarm 4 3 Printout of recorded values on built in printer 4 3 1 Printout of the Delivery Ticket Delivery Ticket is a short form serving as a document for delivery of transported goods It contains recorder identification date and time of the printout and current measured temperature values from both channels At the lower part there is a space for signature of the responsible person Start printing of Delivery Ticket from basic display by pressing PRINT Then offer of Del
25. ed only via USB interface from the computer printout on built in printer is disabled because supplied energy is not sufficient for print A TALE 6 ATAL 4 0 Using of recorder 4 1 Recorder controls Recorder is controlled by the user by means of built in five button keyboard and graphic display Important information on recorder state is also indicated by green and red LEDs and enable user to watch recorder from longer distance and at the dark Blinking green LED RECORD indicates record in progress blinking red LED ALARM indicates active alarm i e one or both temperatures are outside of adjusted limits or one or both binary channels are in alarm state Built in printer is equipped with paper shift button and dual colored LED which is OFF in usual operation During printout or printer initialization LED blinks green if printer is out of paper LED blinks red Recorder is equipped with illumination of display and keyboard for the operation in worse light conditions Illumination is activated by pressing any keyboard button and it is automatically switched off after about 30 seconds after the last pressing of the keyboard Function of keyboard upper row buttons is defined by actual description of each button on the lower LCD line display Function of lower buttons is fixed Lower buttons serve always for movement in menu or for change of edited item upwards downwards 42 Basic display readings In basic operation LCD displays actually m
26. ed to enter journey starting hour see page 12 If journey start time is not entered i e function is disabled and at the same time journey duration is set in number of days time 0 00 h of last printed day is considered as journey start time If both functions are enabled simultaneously in menu of definition printed values from particular time period i e both Journey Duration in hours and Journey Start Time the printout will be stopped after at least one condition is valid If only function Journey Start Time is enabled in menu and journey duration is entered just before printing i e in number of days then adjusted journey start time is relevant only if journey duration is set to one day If adjusted to more days recorded values will be printed back to time 0 00 h of the first journey day If printout of older values is required it is activated by entering date and optionally time of journey end in menu item Journey End Date and Journey End Time see page 14 Above settings for printout of only particular time period are the same also for printing of older values 4 3 2 2 Start of print of recorded values Enter print mode in basic display by pressing PRINT button Offer of printout of Delivery Ticket Journey Ticket or Graph Ticket appears Select one of the offer by buttons A or V After selecting Journey Ticket or Graph Ticket it is enabled by repeated pressing of button DAY to select journey duration form to 7 days Another pr
27. ery for internal clock For recorder operation external power source is necessary e g vehicle battery It can be also ac dc adapter type SELV Secured Extra Low Voltage source with limited output current or with overcurrent protection used in stationary operation of the recorder Temperature range of used cables must comply with environmental temperatures in which the logger will be used Installation procedure in the vehicle e recorder is not water resistant it must be installed inside of a vehicle cabin e there is necessary to find suitable place for recorder mounting with metal holders using Drill four holes for self cutting screws into suitable place Do not assembly recorder now e in planning cable routes remember cables must lead to recorder from back side where connection terminals are placed Use twin core cable for power with minimal conductor area A TALE ATAL 3 of 0 75 mm For routing cables use cable channels by sides of the thermo isolating body if exist All drilled holes must be finally sealed by suitable sealing material e g silicon sealant Freely installed cables must be fixed by suitable cable clips against movement along all route e recorder power cable lead to fuse box and connect it behind the fuse protecting vehicle battery not directly on vehicle battery Mind correct polarity recorder does not work if poles are incorrectly connected but will not be damaged Do not insert fuse yet e pull
28. espond to suspected temperature in places of installed temperature probes If both temperatures are the same make sure by heating one of the probes e g by short holding in your hand probe are not changed over Make sure if closing and opening contacts on binary channels e g by door opening closing cause proper reading change on recorder LCD on channel 3 and channel 4 preset symbols are ON and OFF Test printer function by printing e g Delivery Ticket Attention Correct temperature measurement is subject to setting proper correction of probe cable length Factory setting of the probe length corrections if not differently ordered is 5 meters for channel 1 and 20 meters for channel 2 for used cable with conductor area 0 14mm2 For setting see page 21 Nor during mounting of temperature probe cable and during the operation insulation of probe cable must not be damaged In case of short circuit of the temperature probe lead with vehicle frame recorder can be damaged If cable of temperature probe is damaged do not connect it to recorder Cable must be repaired or replaced A TALE 4 ATAL Recorder connection to source and temperature probes channel 1 temperature channel 2 temperature channel 3 binary channel 4 binary Legend 1 external power source vehicle battery 2 fuse box of the vehicle 3 power cable 4 temperature probes 5 cables of binary inputs 6 magnetic door contact 7 R
29. essing of button DAY indicated by reading gt 7Day selects unlimited time period of printout After confirmation of Journey Ticket by PRINT button printout is started In case of selection of Graph Ticket you are asked to select required temperature channel Graphic printout of binary channels is not enabled Notice If memory is totally full and printout of oldest recorded values is requested the delay from button pressing to print start can be up to 13 seconds It is caused by searching through a large quantity of recorded data If button DAY after selection of Journey Ticket or Graph Ticket does not appear it means precise setting of journey duration in hours is used menu item Journey Duration see page 12 A TALE 8 ATAL 4 3 2 3 Data contained in numerical table of values Journey Ticket Each recorded value or pair of values for two recorded channels is printed in table on separate line together with storing time and temperature unit C or F If recorded value is outside of adjusted limits for proper channel it is printed in table inversely Adjusted delay of alarm is ignored in this case If selected logging mode of average values or logging mode of min max average only average temperature value for interval are printed Such line is indicated in table by symbol Time value in line in such case indicates end of the interval average value was calculated for Hyphens in printout indicate values outside recorder
30. f recorded values will not be limited by this function If function is enabled at the same time with function JourneyStartTime print time period can be limited by time adjusted in item JourneyStartTime Attention If function Journey Duration is enabled i e duration is set in hours it is not possible to set journey duration in days simplified selection of journey duration is disabled and button DAY does not appear for more details see page 8 2 0 JourneyStartTime Defines time of journey start in whole hours at range from 0 to 23 h This function enables to print records only from one day 1 e in actual day or in print of history in day of required print item Journey End Date Use button CHANGE and then buttons A V or gt for setting itself Active function it is possible to disable by button DISABL If function is disabled print of recorded values will not be limited by this function If function is enabled at the same time with function Journey Duration print time period can be limited by time adjusted in item Journey Duration ATA UE 12 LAG Illustration of concurrence of function Journey Duration and JourneyStartTime valid only for setting journey duration in hours not in days Example 1 setting of time in item JourneyStartTime is irrelevant 3 00 00 15 7 3 30 00 15 7 4 00 00 15 7 4 30 00 15 7 5 00 00 15 7 5 30 00 15 7 6 00 00 15 7 6 30 00 15 7 7 00 00 15 7 7 30 00 15 7 8 00 00 15 7 8 30 00 15
31. g is identical as in item Logger Location see above 6 1 5 Set Date If there is a need to change the date in recorder internal clock enter editing mode by button CHANGE Edited digit is indicated from above and below by arrows and it is possible to change it by buttons A or V Recorder does not allow to set values outside of interval 01 to 31 for day and 01 to 12 for month Shift to another edited digit by button gt Only two last digits in range 00 to 99 are editable in year indication Use button STORE to store edited date to recorder internal clock or button CANCEL to end editing without storing 6 1 6 Set Time If there is a need to change the time in recorder internal clock enter editing mode by button CHANGE Edited digit is indicated from above and below by arrows and it is possible to change it by buttons A or V Recorder does not allow to set values outside of interval 00 to 23 for hour and 00 to 59 for minute Shift to another edited digit by button Use button STORE to store edited ATA OE 16 MAG time to recorder internal clock seconds will be zeroed or button CANCEL to end editing without storing 6 1 7 Temperature Unit This menu item enables after pressing button CHANGE to select between two temperature units C or F Recorder works with selected temperature unit in measurement value on display record to recorder memory and in alarming adjusted limits Change the used temperature unit by buttons A or V Use
32. ivery Ticket Journey Ticket or Graph Ticket printing is displayed Select by means of the arrow buttons A or V one of the offered item Confirm Delivery ticket by pressing PRINT and Delivery ticket is printed out When request for print is repeated always last time used ticket is offered as first Delivery Ticket Journey Ticket or Graph Ticket to simplify repeated printing A TALE ATAL 7 4 3 2 Printout of recorded values 4 3 2 1 Selection of values for printout Recorded values can be printed in table or graph formats Recorded values are printed out always backward from newest values towards oldest If not required and not adjusted printout of older values printout starts with last value recorded in memory How many values from the recorder memory will be printed out is defined by the actual recorder setting If journey has just ended and printout of recorded values from the journey duration is required two basic settings are available which also can be combined A entering of journey duration i e the length of time period to be printed B entering of journey start time i e entering of hour in the day when journey started ad A setting of journey duration is simplified to entering number of days 1 to 7 days in offer just before starting the printout or more precisely but in more complex way in hours in menu item Journey Duration see page 12 ad B for printout in one day only in menu item Journey Start Time it is enabl
33. justed menu items are identical for both temperature channels Setting of proper channel is indicated at the LCD upper part by symbol of mounting spanner with digit indicating adjusted channel 6 2 3 1 Chan Description Enables to enter description of location of temperature probe for proper channel with 16 characters Description will be visible on each printout from built in printer Edit text after pressing button CHANGE Edited character je indicated from above and below by arrows and change is enabled in alphabetical order by buttons A V Optionally it is possible to swap between capital letters and lower case letter or symbols by means of button 1 A a Space character is first character of symbols and follows after last character of lower case letters z Digits are part of symbols Shift to another edited character in text string by button gt Standard offering STORE to store edited text or CANCEL to end editing without storing are available after pressing button NEXT 6 2 3 2 Upper AlarmLimit Enables after pressing button CHANGE to set upper temperature limit of proper channel After exceeding the limit alarm delay is counted If specified delay time value is exceeded alarm is activated visually optionally acoustically Value of alarm limit is adjustable at the range 130 to 500 Temperature unit of alarm limit depends on setting of temperature unit in general setting After change of temperature unit adjusted values of alarm limit
34. s remain without change ATAI LAG 17 Edited digit of alarm limit is indicated from above and below by arrows and it is possible to change it by buttons A or V Shift to another edited digit by button gt Use button STORE to store alarm limit to recorder or button CANCEL to end alarm limit adjustment without storing 6 2 3 3 Lower AlarmLimit Adjustment of lower alarm limit is analogical with above setting of upper alarm limit 6 2 3 4 Alarm Delay Enables to set after pressing button CHANGE at the range of 0 to 60 minutes Delay is counted from the moment when measured temperature of proper channel exceeds adjusted alarm limit If temperature during delay counting returns to adjusted limits delay is counted after new exceeding of alarm limits again from the beginning After elapsing of adjusted delay visual optionally audible alarms are activated Edited digit of alarm delay is indicated from above and below by arrows and it is possible to change it by buttons A or V Shift to another edited digit by button gt Use button STORE to store alarm delay to recorder or button CANCEL to end alarm delay adjustment without storing 6 2 3 5 Alarm ON OFF Enables to disable the evaluation of alarms by setting this item to disabled Alarms of this channel then will not be evaluated and adjusted values of alarm limits and alarm delay are irrelevant Change the state of alarm evaluation after pressing button CHANGE Select value enabled
35. s to change illumination intensity of LCD display from 0 to 100 with 10 step Level 0 means illumination permanently disabled 100 is maximum level of illumination Use buttons A V or gt for setting itself selected level confirm by button STORE Illumination is activated by pressing any keyboard button and is switched off automatically after 30 seconds 8 0 Language Select This function enables to select one from the maximum 15 languages of recorder menu E g following languages can be selected English German French Italian Polish Dutch Spanish Portuguese Romanian Czech Select language by buttons A or V confirm selected language by button STORE ATAI AHH 15 4 4 2 Menu 6 0 ParameterSetting 6 1 General Setting Menu item General Setting concerns entire recorder all channels Movement in menu General Setting is indicated in upper part of the display by symbol of a mounting spanner 6 1 1 Logging interval Defines interval for storing of values from both temperature channels to internal memory Memorizing of the first value is synchronized with the internal real time clock so the record is performed at sharp multiples of minutes hours and days E g after starting the record with the 15 minute interval the first value is not stored immediately but after the internal clock gets the status of a quarter a half or a whole hour First interval after switching on the recorder or after parameter setting is always shorter
36. t be visible 4 3 2 5 Stopping of printout of Journey or Graph Ticket Printout of Journey or Graph Ticket in progress can be stopped manually anytime by button CANCEL automatically if preset journey duration is printed out already automatically if preset time for print end was exceeded in menu item JourneyStartTime automatically if all recorded values are printed out already At the end of printout always record header is printed Header enables to identify record accordingly to recorder serial number its description its location must be entered before in recorder and date of print Tear off printed out paper over tear edge of the printer Warning if back up battery of internal clock is low and at the same time recorder was not continuously powered from external source time reading may not be valid which is indicated by inverse print of time value ATAI 10 MAL 4 3 3 Paper replacement in built in printer Last meter of paper in the roll is marked by colored strip indicating paper will be finished soon If paper is finished during printout LED on printer shortly blinks in red and LCD reports Load paper Insert new paper in accordance with described procedure below After installation of the new roll of paper press shortly shift button on printer lt and printout will continue After inserting new paper pull gently lever on the lid and release printer lid Pressure roll for paper transport is released from driving
37. through carefully temperature probe cable without insulation damage to measured point Locate temperature probes to places with good air circulation Avoid places influenced by local heat sources illuminating lamps etc The best place is the ceiling of the body Due to subsequent calibrations it is also suitable to fix last meters of the cable with temperature sensor the way enabling to remove cable from the holders and put cable to the floor to calibration device e similarly lead cables of door contact or other monitored device from recorder binary channels Shielding of cable on contact side let unconnected e shorten cables to required length and form them not to be crossed e strip wire ends of all cables and fit them with closed crimp barrel of suitable diameter included and crimp by proper crimping tool Connect wires including shielding to proper terminals Follow description at the bottom of the case Careless crimping of the barrels or not using crimp barrels can cause subsequent accidental measurement failures e mount recorder in working position Use four self cutting screws with diameter 4 mm suitable lenghts Remember screws must resist vibrations during operation e insert fuse to the fuse box LCD and the recorder should start to work e verify correct recorder function display would be illuminated always only 30 seconds after pressing a key and green LED diode RECORD must blink temperature readings on both channels would corr
38. tion Erasing device memory or by confirmation the offer during data transfer Data logging works in cyclic mode That is why it is not necessary to erase the data if memory is filled older recorded values are overwritten by newer values 6 0 Replacement of back up battery If back up battery of internal clock is low and at the same time recorder was not continuously powered from external source time reading is not valid This is indicated by inverse printout of time value Used battery is button battery 3 V type CR2032 located in holder under recorder bottom cover Replacement procedure e demount recorder e disconnect all terminals from recorder power and temperature probes e lever up rubber covers from bottom side of recorder e by means of a suitable screwdriver unscrew six screws from the back of the case and remove the recorder cover remove old battery from the holder by means of a suitable flat screwdriver e insert new battery with correct polarity pole of the battery must be visible from above e put back the recorder cover with holders and screw the screws Put back also rubber covers e set internal clock of recorder from recorder keyboard or from the computer Liquidate discharged battery ecologically ATA UE 22 MAG 7 0 7 1 C Technical parameters Technical parameters of the recorder Measuring range of the RTD Pt1000 3850ppm input 90 to 260 C Measuring range of the RTD Ni1000 6180ppm input
Download Pdf Manuals
Related Search