JY997D16401B INSTALLATION MANUAL
Contents
1. Manual Products INSTALLATION PRECAUTIONS FEX Manual Number JY997D16401 n e This manual describes the part names mounting and specifications of the product Before use read this manual and manuals of dimensions relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Dec 2005 NCAUTION e Use the product in the environment within the general specifications described in PLC main unit manual Hardware Edition Never use the product in areas with dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S NH3 SO2 or NO2 flammable gas vibrations or impacts or expose it to high temperature condensation or wind and rain If the product is used in such a place described above electrical shock fire malfunction damage or deterioration may be caused When drilling screw holes or wiring cutting chips or wire chips should not enter ventilation slits Such an accident may cause fire failure or malfunction HOUR 1 2 Output Number and Signal When power is turned on the output numbers and signal2. to AM26C31 Ground resistance Seve Amplifier LOPE Obese or Drive Unit re Ground resistance 100Q or less 1 YOO indicates output number of the high speed output special adapter 2 SGA is insulated from SGB 3 Ground properly with reference to the Servo Amplifier or Drive Unit manual If not indicated ground as below Grounding Ground properly with reference to the Servo Amplifier or Drive Unit manual If not indicated ground as below Grounding when not indicated The grounding resistance should be 100Q or less Independent grounding should be performed for best results When independent grounding is not performed perform shared grounding of the following figure For details refer to the FX3U Series User s Manual Hardware Edition Another equipment Independent grounding Shared grounding Common grounding Best condition Good condition Not allowed The grounding wire size should be AWG 14 2 mm or larger The grounding point should be close to the PLC and all grounding wire should be as short as possible This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for dam
3. and DC megger ground terminal of PLC main unit Dielectric withstand voltage Wire size Insulation Single wire 0 3mm to 0 5mm AWG22 to 20 ES Sane Manual Hardware Edition 2 wire 2 vi f 0 3mm2 AWG22 ees Another Another Another Biers Oh ein 4 3 Power Supply Specification equipment ie equipment equipment 3 Termination of cable end Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve Al 0 5 8WH Specification L Independent grounding Best condition Item Common grounding Not allowed Shared grounding 60mA for 24V DC Good condition Internally supplied from the main unit service power supply 30mA for 5V DC 5V DC power is supplied internally from the main unit Output circuit driving power supply The grounding wire size should be AWG 14 2 mm or larger The grounding point should be close to the PLC and all grounding wire should be as short as possible Caulking tool CRIMPFOX UD6 Adapter driving power supply Manufacturer Phoenix Contact Co Ltd Strand wire single wire 4 4 Performance Specification Stick terminal with insulating sleeve Insulation sleeve Contact area Item Specification This manual confers no industrial property rights or any rights of any other kind Number of i i i i
4. communication analog special adapter For system configuration refer to the FX3uU Series User s Manual Hardware Edition indieaias anal incorrect handling may cause hazardous Status of Output number 7 Output mode setting switch Dismount the main unit and special adapter mounted on DIN rail or mounted si ia me output form z directly using screws NCAUTION conditions resulting in medium or slight personal injury tne Signal name Firstunit e Second unit Name Setting 2 Install an expansion board to the main unit or physical damage Switch 1st axis 2nd axis 1st axis ond axis Upper EP RP side Fwd pulse train FP For installation of expansion board refer to the following manual PP Rev pulse train RP Refer to the FX3U Series User s Manual Hardware Edition Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage Remove the high speed I O special adapter connector cover Right fig A and the special adapter connector cover Right fig B on the main unit In case of connecting this product to a high speed I O special adapter as an addition please replace the main unit in the above description with a special adapter and perform the procedure as indicated Please replace the following procedures similarly Slide the special adapter slide lock Rig
5. side replace the following procedures similarly 3 Name plate 4 Slide the special adapter slide lock Right 4 Special adapter slide lock fig C of the main unit Used to connect special adapter on left side of this special adapter 5 Special adapter connector cover Remove this cover for connecting special adapter on the left side 5 Connect the high 6 Output terminal block European type speed I O special Connected to Servo Amplifier or Drive Unit to which pulse signal of differential adapter Right line driver system can be input fig D to the main 7 Output form setting switch unit as shown on Either Forward pulse train FP Reverse pulse train RP or pulse train the right direction is selected For setting refer to the following manual 6 Slide back the Refer to FX3u FX3UC Series User s Manual Positioning Control Edition special adapter 8 Output LED red slide lock Right Lit when output turns ON if output turns ON and OFF alternately at high speed fig C of the main LED flickers fast unit to fix the high 9 POWER LED green speed I O special Lit while power is properly supplied from main unit oo Right ig C 10 Direct mounting hole 2 holes of 4 5 0 18 mounting screw M4 screw 11 Special adapter fixing hook 12 DIN rail mounting hook 13 Special adapter connector Used to connect communication special adapter or analog special adapter to this adapter on left side Connectio
6. unit Refer to FX3u Series User s Manual Hardware Edition Item Dielectric Specification Conforming to JEM 1021 withstand voltage 500V AC for one minute Between output terminal of high 5MQ or more by 500V SPeed output special adapter and DC megger ground terminal of PLC main unit 4 3 Power Supply Specification Insulation resistance Item Specification 60mA for 24V DC Internally supplied from the main unit service power supply 30mA for 5V DC 5V DC power is supplied internally from the main unit Output circuit driving power supply Adapter driving power supply 4 4 Performance Specification Item Specification Number of Independent two axes controlled axis Output points 4 points Not counted among the total I O points of the PLC Output system Differential line driver Equivalent to AM26C31 Output form Forward pulse train reverse pulse train or pulse train direction Load current 25 mA or less Maximum output 200 kHz frequency e External cables of output area are insulated from PLC by Insulation photo coupler or transformer e SG are insulated from each other by transformer Wiring length Maximum 10m 32 9 4 5 Output Interface Internal Circuit For connection example and wiring refer to the following manual Refer to FX3uU FX3uc Series User s Manual Positioning Control Edition High speed output special Servo Amplifier adapter or Drive Unit
7. 0 35 Manufacturer Caulking tool CRIMPFOX UD6 Phoenix Contact Co Ltd Contact area 2 6mm 0 1 When using a stick terminal with insulating sleeve choose a wire with proper cable sheath referring to the above outside dimensions or otherwise the wire cannot be inserted easily The tightening torque must be 0 22 to 0 25N em 4 Specification STARTUP AND MAINTENANCE CAUTION PRECAUTIONS Do not disassemble or modify the unit Doing so may cause failure malfunction or fire For repair contact your local Mitsubishi Electric distributor Do not drop the product or do not exert strong impact doing so may cause damage DISPOSAL PRECAUTIONS DANGER e Please contact a company certified in the disposal of electronic waste for environmentally safe recycling and disposal of your device TRANSPORT AND sTORAGE PRECAUTIONS CAUTION e During transportation avoid any impact as the product is a precision instrument Check the operation of the product after transportation 4 1 Applicable PLC Model name Applicability FX3U Series PLC _ Ver 2 20 from the first product and later The version number can be checked by monitoring D8001 as the last three digits indicate it Note Cannot be connected to FX3UC 32MT LT 4 2 General Specifications For general specifications refer to the manual of the PLC main unit The items other than the following are equivalent to those of the PLC main
8. JY997D16401B Fa sAPANESE Mo ENGLISH a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEG IF FX3U 2HSY ADP INSTALLATION MANUAL Side Changes for the Better 1 Outline The FX3U 2HSY ADP high speed output special adapter hereinafter called high speed output special adapter is a special adapter dedicated to FX3U Series PLC It outputs pulse signals of a differential line driver system for applicable Servo Amplifiers or Drive Unit of an AC servomotor or stepper motor Up to two units of this special adapter can be connected to the main unit per system For system configuration refer to the FX3U Series User s Manual Hardware Edition 1 1 Incorporated Items Check if the following product and items are included in the package A 2 During STOP or PLC power off modes set the output form operation Do not set the output form operation during pulse train output 1 3 External Dimensions Part Names and Terminal Layout 4 5 6 2 4 5 Mounting holes 11 2 Installation The product can be mounted on DIN rail DIN46277 or mounted directly using screws For installation uninstallation and safety precautions refer to the following manual too Refer to the FX3u Series User s Manual Hardware Edition DANGER e Cut off all phases of the power source externally before starting the INSTALLATION PRECAUTIONS installation or wiring work thus avoiding electric shock or damages to the product
9. a F controlled axis Independent two axes nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be aoe held responsible for any problems involving industrial property rights which may Output points 4 points Not counted among the total I O points of the PLC occur as a result of using the contents noted in this manual i a Output system Differential line driver Equivalent to AM26C31 Warranty When using a stick terminal with insulating sleeve choose a wire with proper Mitsubishi will not be held liable for damage caused by factors found not to be cable sheath referring to the above outside dimensions or otherwise the wire Output form fees pulse tall Teveroe Pulse Main OF Pulse Wall the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties cannot be inserted easily The tightening torque must be 0 22 to 0 25N m Load current 25 mA or less Maximum output frequency 200 REZ AN For safe use e External cables of output area are insulated from PLC by Insulation photo coupler or transformer e This product has been manufactured as a general purpose part for general e SG are insulated from each other by transformer industries and has not been designed or manufactured to be incorporated in a device or
10. age caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
11. are subject to change without notice 2005 Mitsubishi Electric Corporation Safety Precaution Read these precautions before use This manual classify the safety precautions into two categories ODANGER and AGAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage Associated Manuals Manual name Description FX3U Series Jvso7piesos EXiains F xau Series PEU User s Manual MODEL CODE specification details for I O wiring installation and Hardware Edition 09R516 maintenance FX3U FX3UC Series Programming Manual Basic amp Applied Instruction Edition FX3U FX3UC Series User s Manual Positioning Control Edition JY997D16601 Describes PLC programming MODEL CODE for basic applied instructions 09R517 and devices JY997D16801 Describes positioning control MODEL CODE and programming using FX3uU 09R620 FX3UC Series PLC How to obtain manuals For the necessary product manuals or documents consult with the Mitsubishi Electric dealer from where you purchase your product Applicable Standard FX3U 2HSY ADP complies wi
12. d to Servo Amplifier or Drive Unit to which pulse signal of differential Output operation line driver system can be input 7 Output form setting switch Either Forward pulse train FP Reverse pulse train RP or pulse train direction is selected For setting refer to the following manual 6 Refer to FX3u FX3UC Series User s Manual Positioning Control Edition Transistor output type While instruction is activated El ouput LED red p Lit when output turns ON if output turns ON and OFF alternately at high speed Operated Operated 1 relevant output is ON LED is P P y gn Sp also ON 19 LED flickers fast Do not apply PWM instruction for basic applied instructions and devices lt Connect the high speed I O special adapter Right fig D to the main unit as shown on the right Slide back the special adapter slide lock Right fig C of the main unit to fix the high speed I O special adapter Right fig C FX3U FX3UC Series User s Manual Positioning Control Edition JY997D16801 MODEL CODE 09R620 Describes positioning control and programming using FX3uU FX3UC Series PLC High speed Main unit output special instructions Relay output type adapter How to obtain manuals For the necessary product manuals or documents consult with the Mitsubishi Electric dealer from where you purchase your product PLSY PLSR DSZR DVIT TBL ZRN PLSV DRVI DRVA POWER LED g
13. ectly using 1 3 External Dimensions Part Names and Terminal Layout screws For installation uninstallation and safety precautions refer to the following manual 2 04 5 too 4 5 6 Mounting holes 11 Refer to the FX3u Series User s Manual Hardware Edition INSTALLATION PRECAUTIONS DANGER e Cut off all phases of the power source externally before starting the installation or wiring work thus avoiding electric shock or damages to the product INSTALLATION PRECAUTIONS CAUTION e Use the product in the environment within the general specifications described in PLC main unit manual Hardware Edition Never use the product in areas with dust oily smoke conductive dusts corrosive gas salt air Cle H2S NH3 SO2 or NO2 flammable gas vibrations or impacts or expose it to high temperature condensation or wind and rain If the product is used in such a place described above electrical shock fire malfunction damage or deterioration may be caused When drilling screw holes or wiring cutting chips or wire chips should not enter ventilation slits Such an accident may cause fire failure or malfunction Do not touch the conductive parts of the product directly thus avoiding failure or malfunction Fix the special adapter securely to the specified connector Incorrect connection may cause malfunction HOUR connector cover 2 or 5 is removed Output number First Seco
14. ht Pulse train direction 3 PLS DIR Lower Forward pulse train FP YOOO YOO1 Y002 Reverse pulse train RP Y004 Y005 YO06 G 1 2 3 FPeRP side Unit mm inches Weight 80 g 0 18 Ibs Associated Manuals PLSeDIR side 1 DIN rail mounting groove DIN rail DIN46277 2 High speed I O special adapter connector cover Remove this cover for connecting high speed I O special adapter on the left side 3 Name plate 4 Manual name Description Explains FX3U Series PLC J 997D16501 specification details for I O MODEL CODE FX3U Series User s Manual x a wiring installation and i f Hardware Edition 09R516 ee Caution 4 Special adapter slide lock fig C of the main unit 1 When a high speed output adapter is connected the same output number is Used to connect special adapter on left side of this special adapter i llocated t th th i it thi ter ith tput t inal FX3U FX3UC Series JY997D16601 Describes PLO programming allocated to bo e main unit and this adapter Use either output terminal and do 5 Special adapter connector cover not wire to the unused output terminal The outputs from the high speed output special adapter and main unit are 6 operated as below 6 Programming Manual Basic amp Applied Instruction Edition MODEL CODE 09R517 Remove this cover for connecting special adapter on the left side 5 Output terminal block European type Connecte
15. ion has not supported the relay output for the reasons of the response delay of the output chattering of contact the contact life etc 3 Used cables and Tightening Torque on Terminal For connection example and wiring refer to the following manual Refer to FX3U Series User s Manual Hardware Edition 4 Specification STARTUP AND 4 5 Output Interface Internal Circuit For connection example and wiring refer to the following manual Refer to FX3U FX3uc Series User s Manual Positioning Control Edition MAINTENANCE PRECAUTIONS CAUTION Servo Amplifier High speed output special or Drive Unit WIRING adapter PRECAUTIONS DANGER e Cut off all phases of power source externally before installation or wiring work in order to avoid electric shock or damage of product Do not disassemble or modify the unit Doing so may cause failure malfunction or fire For repair contact your local Mitsubishi Electric distributor Do not drop the product or do not exert strong impact doing so may cause damage WIRING PRECAUTIONS CAUTION e Never let cutting chips and wire chips enter the ventilation slits of this product or PLC when performing wiring Otherwise fire failure or malfunction may occur Make sure to observe the precautions below in order to prevent any damage to a machine or any accident which might be caused by abnormal data written in the PLC due to the influence of noise 1 Do not la
16. n precautions e Install the expansion board to be used before connecting a special adapter e Install an expansion board when using a special adapter other than a high speed I O special adapter in combination with a high speed I O special adapter 14 High speed I O special adapter connector l l e Connect all the high speed I O special adapters before connecting other Used to connect high speed I O special adapter to this adapter on left side special adapters when they are used in combination Do not connect a high speed I O special adapter on the left side of a communication or analog special adapter 3 Used cables and Tightening Torque on Terminal For connection example and wiring refer to the following manual Refer to FX3uU Series User s Manual Hardware Edition G PRECAUTIONS DANGER e Cut off all phases of power source externally before installation or wiring work in order to avoid electric shock or damage of product G PRECAUTIONS NCAUTION e Never let cutting chips and wire chips enter the ventilation slits of this product or PLC when performing wiring Otherwise fire failure or malfunction may occur Make sure to observe the precautions below in order to prevent any damage to a machine or any accident which might be caused by abnormal data written in the PLC due to the influence of noise 1 Do not lay close or bundle with the main circuit high voltage power line or load line Otherwise effects of n
17. name Applicability FX3U Series PLC omen Ground resistance 100Q or less Ver 2 20 from the first product and later The version number can be checked by monitoring D8001 as the last three digits imdigare it 1 YOOO indicates output number of the high speed output special adapter Note 2 SGA is insulated from SGB Cannot be connected to FX3UC 32MT LT 3 Ground properly with reference to the Servo Amplifier or Drive Unit manual If not indicated ground as below 4 2 General Specifications For general specifications refer to the manual of the PLC main unit The items other than the following are equivalent to those of the PLC main unit Refer to FX3u Series User s Manual Hardware Edition Grounding Ground properly with reference to the Servo Amplifier or Drive Unit manual If not indicated ground as below Grounding when not indicated The grounding resistance should be 100Q or less Independent grounding should be performed for best results When independent grounding is not performed perform shared grounding of the following figure For details refer to the FX3U Series User s 1 Wire size To connect to the desired unit use a shielded twisted pair cable having a conductor s of size AWG22 20 2 Applicable cable Type Item Specification 500V AC for one minute Conforming to JEM 1021 Between output terminal of high 5MQ or more by 500V SPeed output special adapter
18. nd unit unit Y0OO00 Y002 Terminal layout of 6 2 1 Connection to the FX3uU Series PLC e Refer to the procedure 2 for configuring a new system e Refer to the procedure 1 for adding product to an existing system Procedure 1 Turn off the power Disconnect all the cables connected to the PLC main unit and special adapter Dismount the main unit and special adapter mounted on DIN rail or mounted directly using screws Name Setting 2 Install an expansion board to the main unit Fwd pulse train FP For installation of expansion board refer to the following manual Rev pulse train RP Refer to the FX3U Series User s Manual Hardware Edition Remove the high speed I O special adapter connector cover Right fig A and the special adapter connector cover Right fig B on the Unit mm inches main unit Weight 80 g 0 18 Ibs In case of connecting this product to a high speed I O special adapter as an addition please replace the main unit in the above description with a special adapter and Output number 7 Output mode setting switch lt Upper FP RP side Lower PLS DIR Pulse train direction 3 1 DIN rail mounting groove DIN rail DIN46277 2 High speed I O special adapter connector cover l l perform the procedure as indicated Please Remove this cover for connecting high speed I O special adapter on the left
19. oise or surge induction are likely to take place Keep a safe distance of more than 100 mm 3 94 from the above when wiring 2 Ground the shield wire or shield of a shielded cable at one point on the PLC However do not ground at the same point as high voltage lines Observe the following items to wire the lines to the European terminal board Failing to do so may cause electric shock short circuit disconnection or damage of the product The disposal size of the cable end should follow the dimensions described in this manual Tighten to a torque should follow the torque described in this manual Twist the end of strands and make sure there is no loose wires Do not solder plate the electric wire ends Connect only the electric wires of regulation size Fix the electric wires so that the terminal block and connected parts of electric wires are not directly stressed 1 Wire size To connect to the desired unit use a shielded twisted pair cable having a conductor s of size AWG22 20 2 Applicable cable Type Wire size Single wire 0 3mm to 0 5mm AWG22 to 20 2 wire 2 pieces of 0 3mm AWG22 3 Termination of cable end Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve Al 0 5 8WH Strand wire single wire Stick terminal with insulating sleeve Insulation sleeve
20. on refer to the FX3U Series User s Manual Hardware Edition Status of Output number setting Forward pulse train FP YOOO YOO1 Y002 Reverse pulse train RP Y004 Y005 YO06 FPeRP side Caution 1 When a high speed output adapter is connected the same output number is allocated to both the main unit and this adapter Use either output terminal and do not wire to the unused output terminal The outputs from the high speed output special adapter and main unit are operated as below PLSeDIR side SG4 Output operation instructions High speed Main unit output special Transistor adapter output type Relay output type PLSY PLSR DSZR _ While instruction is activated DVIT TBL ZRN Operated Operated relevant output is ON LED is PLSV DRVI DRVA also ON Do not apply PWM instruction PWM Operated Operated for relay output type main unit 1 The output frequency of transistor outputs in the main unit is a maximum of 100kHz If the load is operated using pulses at a frequency more than 100kHz PLC may be damaged 2 PWM instruction has not supported the relay output for the reasons of the response delay of the output chattering of contact the contact life etc A 2 During STOP or PLC power off modes set the output form operation 2 Installation Do not set the output form operation during pulse train output The product can be mounted on DIN rail DIN46277 or mounted dir
21. reen Lit while power is properly supplied from main unit Applicable Standard FX3U 2HSY ADP complies with EC directive EMC Directive and UL standards UL c01 Funker ijormation can be found it tie tellowina manual PWM Operated Operated for relay output type main 10 Direct mounting hole 2 holes of 4 5 0 18 mounting screw M4 screw A ig O So Refer to FX3U Series Hardware Manual Manual No JY997D18801 unit 11 aio adapter a Connection precautions Other Operated Operated Operated 12 i medntiag nee e Install the expansion board to be used before connecting a special adapter 13 Special adapter connector e Install an expansion board when using a special adapter other than a high speed I O special adapter in combination with a high speed I O special adapter e Connect all the high speed I O special adapters before connecting other special adapters when they are used in combination Do not connect a high speed I O special adapter on the left side of a communication or analog special adapter Used to connect communication special adapter or analog special adapter to this adapter on left side 14 High speed I O special adapter connector Used to connect high speed I O special adapter to this adapter on left side 1 The output frequency of transistor outputs in the main unit is a maximum of 100kHz If the load is operated using pulses at a frequency more than 100kHz PLC may be damaged 2 PWM instruct
22. s of the high speed output special adapters are allocated as shown in the table below in the order of it near the main unit Second unit First unit connector cover 2 or 5 is removed Output number Specifications are subject to change without notice Analog Analog Analog ala ee oe First Second ans a conductive parts of the product directly thus avoiding failure 2005 Mitsubishi Electric Corporation H eT E ae input output output Main unit unit unit a sat p function function function special special special Yooo Y002 Fix the special adapter securely to the specified connector adapter adapter adapter adapter adapter adapter Incorrect connection may cause malfunction Safety Precaution Read these precautions before use This manual classify the safety precautions into two categories RODANGER ana AGAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Terminal layout of 6 2 1 Connection to the FX3uU Series PLC e Refer to the procedure 2 for configuring a new system e Refer to the procedure 1 for adding product to an existing system Procedure 1 Turn off the power Disconnect all the cables connected to the PLC main unit and special adapter Expansion board Output number 1 A function extension board is required to use the high speed I O special adapter together with a
23. system used in purposes related to human life Wiring length Maximum 10m 32 9 e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system sa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN Side JY997D16401B B E JAPANESE B ENGLISH ate MITSU BISHI Changes for the Better PROGRAMMABLE CONTROLLERS MELSEG IF FX3U 2HSY ADP INSTALLATION MANUAL FX 3y e This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Dec 2005 Specifications
24. th EC directive EMC Directive and UL standards UL cUL Further information can be found in the following manual Refer to FX3U Series Hardware Manual Manual No JY997D18801 1 Outline The FX3U 2HSY ADP high speed output special adapter hereinafter called high speed output special adapter is a special adapter dedicated to FX3U Series PLC It outputs pulse signals of a differential line driver system for applicable Servo Amplifiers or Drive Unit of an AC servomotor or stepper motor Up to two units of this special adapter can be connected to the main unit per system For system configuration refer to the FX3U Series User s Manual Hardware Edition 1 1 Incorporated Items Check if the following product and items are included in the package Products Manual 1 2 Output Number and Signal When power is turned on the output numbers and signals of the high speed output special adapters are allocated as shown in the table below in the order of it near the main unit Second unit First unit Analog Analog Analog High High High l speed speed speed special special special Pn Saran Saw p Main unit function function function special special special adapter adapter adapter adapter adapter adapter Expansion board 1 A function extension board is required to use the high speed I O special adapter together with a communication analog special adapter For system configurati
25. y close or bundle with the main circuit high voltage power line or load line Otherwise effects of noise or surge induction are likely to take place Keep a safe distance of more than 100 mm 3 94 from the above when wiring 2 Ground the shield wire or shield of a shielded cable at one point on the PLC However do not ground at the same point as high voltage lines Observe the following items to wire the lines to the European terminal board Failing to do so may cause electric shock short circuit disconnection or damage of the product The disposal size of the cable end should follow the dimensions described in this manual Tighten to a torque should follow the torque described in this manual Twist the end of strands and make sure there is no loose wires Do not solder plate the electric wire ends Connect only the electric wires of regulation size Fix the electric wires so that the terminal block and connected parts of electric wires are not directly stressed DISPOSAL PRECAUTIONS DANGER e Please contact a company certified in the disposal of electronic waste for environmentally safe recycling and disposal of your device TRANSPORT AND NCAUTION STORAGE PRECAUTIONS e During transportation avoid any impact as the product is a precision instrument Check the operation of the product after transportation 3 Grounding Ground resistance 1002 or less Servo Amplifier or Drive Unit 4 1 Applicable PLC Model
Download Pdf Manuals
Related Search