Installation Manual
Contents
1. Controller and or the closest Z Wave Repeater 77 F 25 C Z Wave and Z Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countries REGULATORY INFORMATION The LB60Z 1 is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference received that may cause undesired operation FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Incre2. If removed from a group it functions as a repeater only RESET UNIT removes it completely from the network To Reset Unit If Required In the event that your primary controller is lost or otherwise inoperable to reset the bulb and clear all network information follow these steps 1 Use the wall switch to turn the power to the bulb OFF then ON four times within four seconds 2 The Smart LED Light Bulb will flash twice when the reset occurs Before repeating the steps above try moving the Smart LED Light Bulb to a socket in the same room as the Controller Gateway in case the preferred socket is out of range initially Repeat Steps 1 3 above until the Smart LED Light Bulb is added to the network Once the bulb has been successfully added to the network move it to the preferred location Removing from a network The Smart LED Light Bulb can be removed from the network by the Controller Gateway Refer to the Controller operating instructions for details 1 Set the Controller into Removal Mode and follow its instruction to delete the LB60Z 1 from the Controller 2 Reset the bulb by using the wall switch to turn the power to the bulb ON The Smart LED Light Bulb will flash twice to confirm the removal BASIC OPERATION Remote Control Operation The Smart LED Light Bulb can be controlled ON OFF BRIGHT DIM through wireless signals from the Z Wave remote controller or through a gateway via an application on a smart phone
3. BF NORTEK SECURITY amp CONTROL PLUS oe eo cus LISTED Gocortrol LB60Z 1 Radio Frequency Controlled Smart LED Light Bulb 750 Lumens Equivalent to a 60 Watt incandescent light bulb Po NOTE This unit must be added to the Network only where it will be permanently installed The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes You cannot test bench configure this unit then install LB60Z 1 SMART LED LIGHT BULB The GoControl family of Z Wave certified wireless lighting products smart LED bulbs switches dimmers outlets and plug in modules and security devices alert sounder passive infrared sensor and door window transmitter bring a new level of intelligent wireless capability to commercial and residential environments The Z Wave wireless protocol is an international wireless standard for remote home automation security and other applications Embedded in each device the Z Wave smart chip enables two way RF communication among hundreds of Z Wave enabled devices allowing products and services from multiple manufacturers to work seamlessly The LB60Z 1 Smart LED Light Bulb is simple to set up and provides longer life and more energy efficiency than incandescent or florescent light bulbs The bulb is instant on without the warm up delay common in CFL bulbs GoControl Z Wave products are easy to install and allow dealers
4. ase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician to help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment IC Notice This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement This device complies with the Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device WARRANTY This Nortek Security amp Control product is warranted against defects in material and workmanship for twenty four 24 months based on three 3 hours of use per day This warranty extends only to wholesale customers who buy direct from Nor
5. med dimming step level Configuration Option Default 1 The step level is small when the value is low The step level is large when the value is high Parameter 10 Dim Bright Speed When the brightness is adjusted by the controller gateway how fast the bulb brightness will change is set by the programmed dimming step speed Configuration Option Default 3 The step speed is fast when the value is low The step speed is slow when the value is high Example If Parameter 9 is set to the default value of 1 setting Parameter 10 from 1 to 10 will equal the number of seconds it takes to dim down the bulb when the bulb is turned off i e 1 equals 1 second for the bulb to dim down and turn off 10 equals 10 seconds for the bulb to dim down and turn OFF Z Wave Plus Features The LB60Z 1 contains a Z Wave 500 Series Module that supports Z Wave Plus features A Z Wave certified portable or stationary controller can communicate with the Z Wave 500 Series Module Depending on the capability of the controller or gateway software the following operations can be performed with the Smart LED Light Bulb Refer to the controller or gateway manual for details e Turn the bulb ON and OFF e Dim the bulb e Add or Remove the Smart LED Light Bulb e Assign the Smart LED Light Bulb to a specific Group Scene and or to include the bulb as part of ALL ON or ALL OFF system commands e Over the air firmware u
6. pdate by the gateway or static controller e Lifeline function which automatically notifies the associated modules and the network that a manually reset device is no longer in the network thus the corresponding association becomes invalid INTEROPERABILITY WITH Z WAVE DEVICES A Z Wave network can integrate devices of various classes of products and these devices can be made by different manufacturers The GoControl Smart LED Light Bulb has Z Wave certification which guarantees interoperability ASSOCIATION The LB60Z 1 supports one Group with five Nodes for lifeline communication Group 1 must be assigned the Node ID of the controller to which unsolicited notifications from the LB60Z 1 will be sent The Z Wave controller should set this association automatically after inclusion You can associate up to five Z Wave devices to Group 1 Lifeline association only supports the manual reset event For instructions on how to set lifeline association please refer to your wireless controller instructions Copyright 2015 Nortek Security amp Control LLC Normal Operating Temp Repeater Yes SPECIFICATIONS Power Supply 120 VAC 60 Hz Brightness 750 lumens Equivalent to 60 Watt incandescent light bulb Power Consumption 9 Watts Color Temperature 2700K Bulb Lifetime 25 000 hour equivalent 22 8 years based on 3 hours day Radio Frequency 908 4 MHz 916 MHz Wireless Range Up to 130 feet line of sight between the Z Wave
7. respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies regardless of code settings Changes or modifications to the device may void FCC compliance Infrequently used radio links should be tested regularly to protect against undetected interference or fault A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer and these facts should be communicated to the ultimate users BF NORTEK SECURITY amp CONTROL USA amp Canada 800 421 1587 amp 800 392 0123 760 438 7000 Toll Free FAX 800 468 1340 www nortekcontrol com 10002123 X18
8. tablet or PC Once the Smart LED Light Bulb has been added to the network depending on the functions supported by your controller it can be assigned to a Group or Scene and operate when the ALL ON or ALL OFF command is received from the Controller It can also be set in Association with another Z Wave device to perform a specific duty Manual Operation The Smart LED Light Bulb can be manually operated using the wall switch while keeping it on line with the Z Wave network To manually turn the Smart LED Light Bulb ON Flip the wall switch OFF then ON Be sure the switch is ON when finished To manually turn the Smart LED Light Bulb OFF Flip the wall switch OFF then ON twice within two seconds Be sure the switch is ON when finished CONFIGURATION The LB60Z 1 supports the Configuration command The LB60Z 1 can be configured to operate slightly differently than how it works when you first install it Using the Configuration command you can configure the following Parameter 1 Dim Level Memory By default the LB60Z 1 bulb will go to full brightness when turned on To have the bulb turn on to the last dim level setting set Parameter 1 to 1 Valid Values Configuration Option 0 Bulb will be full brightness when turned on default 1 Bulb will turn on to the last dim level setting Parameter 9 Dim Bright Step Level When the brightness is adjusted by the controller gateway how much the bulb brightness will change is set by the program
9. tek Security amp Control or through Nortek Security amp Control s normal distribution channels Nortek Security amp Control does not warrant this product to consumers Consumers should inquire from their selling dealer as to the nature of the dealer s warranty if any There are no obligations or liabilities on the part of Nortek Security amp Control for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property revenue or profit or cost of removal installation or reinstallation All implied warranties including implied warranties for merchantability and implied warranties for itness are valid only until Warranty Expiration Date as labeled on the product This Nortek Security amp Control LLC Warranty is in lieu of all other warranties express or implied All products returned for warranty service require a Return Product Authorization Number RPA Contact Nortek Security amp Control Returns at 1 855 546 3279 for an RPA and other important details IMPORTANT Radio controls provide a reliable communications link and fill an important need in portable wireless signaling However there are some limitations which must be observed e For U S installations only The radios are required to comply with FCC Rules and Regulations as Part 15 devices As such they have limited transmitter power and therefore limited range e A receiver cannot
10. to create an integrated wireless network with nearly limitless expansion and interoperability with security energy management home entertainment appliances and more As part of a Z Wave network the LB60Z 1 will also act as a wireless repeater to insure that commands intended for another device in the network are received This is useful when the device would otherwise be out of the radio range of the wireless controller For indoor use only Retain instructions for future use INSTALLATION 1 At the selected location turn the power to the light bulb socket OFF 2 Screw the Smart LED Light Bulb into the lamp socket Adding to a network Refer to your Controller operating instructions to add this bulb under the command of the Wireless Controller 1 With your controller in Discovery or Add Mode turn the power to the light bulb socket ON 2 You should see an indication on your Controller that the device was added to the network The Smart LED Light Bulb will flash twice 3 The device will appear in the list of Switches It should display multi level switch If the Controller Gateway shows the addition failed repeat Steps 1 3 v NOTE If you have trouble adding the LB60Z 1 to a group it may be that the Home ID and Node ID were not cleared from it after testing You must first RESET UNIT to remove it from the network Although adding it to a group includes it in the network removing it from a group does not remove it from the network
Download Pdf Manuals
Related Search