Instruction Manual
Contents
1. SECURIT RONIX THE IMAGE OF QUALITY INSTALLATION MANUAL ST BT800P W Infrared Dome Camera v1 0 8 4 14 1 PACKAGE CONTENTS This package contains One ST BT800P W infrared dome color camera Mounting Hardware One installation manual Note The ST BT800P W requires a minimum 12VDC 300mA power supply such as the ST PS12VDC1A or ST PS12VDC2A PRODUCT DESCRIPTION The ST BT800P W is an infrared color dome camera The camera uses a 1 4 Color CMOS sensor providing 8000TV lines of resolution The ST BT800P W has a 3 6mm lens for optimal viewing The 3 axis mount makes this camera very easy to install and position The 24 infrared LEDs support low light illumination down to 0 Lux SPECIFICATIONS ST BT800P W Specifications Typical 12 Video Output 1 0Vp p 750 13 Operating Temperature 14F 113 F 14 Power Requirements 300mA 12VDC v1 0 8 4 14 9 INSTALLATION AND OPERATION This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock CAUTION To reduce the risk of electrical shock do not remove the cover or back of this unit No user serviceable parts are inside CAUTION To prevent electric shocks and risk of fire hazards do not use o2. the cables are correctly connected and or the cables are of the correct impedance Other interference may require a Securitytronix ground loop isolation filter Additional troubleshooting assistance can be found on line at www securitytronix com in addition to support from Securitytronix technicians at 1 800 688 9282 option 3 then option 2
3. oltage product v1 0 8 4 14 3 4 WIRING CONNECTIONS a b c d Connect the power supply s DC plug to the camera s power port Connect the camera to the monitor with a 7502 coaxial video cable Connect power supply s AC plug to a suitable AC power outlet Adjust the lens direction according to the required surveillance area and environment DC12Y Power Supply Link wire rule Video aD Power VIDEO AUDIO Video A Video B VideoC al al c N OUT JI IN OUT IN OUT OIOI N OO lalola Video IN Terminal on the back of the monitor v1 0 8 4 14 4 5 TROUBLESHOOTING v1 0 8 4 14 No picture after applying power i check all plugs and cables are securely connected to the proper connectors ii ensure your power supply is providing the correct voltage and current The picture has ripples i check to see if the power supply is experiencing AC ripple if so a filter may be required ii determine if the monitor is faulty iii determine if other peripheral equipment is causing ripple and if so make the necessary adjustments The picture background continuously changes color a fluorescent lamp s magnetic field may cause color roll therefore reduce the number of fluorescent lamps or increase the distance between the camera and the lamps The picture appears smeared i the power supply voltage level may be unstable therefore try another power supply ii ensure
4. ther than specified power source 1 UNPACKING and HANDLING Each unit is shipped assembled and factory tested Ensure that all accessories are removed from the container before discarding packing material 2 MECHANICAL INSPECTION Inspect the front and rear of the equipment for shipping damage Make sure the equipment is clean and no connectors are broken damaged or loose If equipment appears to be damaged or defective please contact your distributor or SecurityTronix at 1 610 429 1511 for assistance 3 SPECIAL ATTENTION a The installer must comply with electrical safety standards There must be sufficient space between the camera s power supply and video line and any high voltage equipment and or cables b To help ensure the cameras life and proper operation do not point the camera towards the sun or strong light Do not install the camera in an environment where the temperature is above 113 F Do not install the camera near a magnetic field or a high power motor Do not mount the camera near a radiator or heater 9 20 Only use a dry cloth to clean the camera If there is dirt that is difficult to remove wipe gently with a mild detergent Never use strong or abrasive detergents g This camera requires a 12VDC 300mA power supply Using AC power or a power supply other than specified will damage the camera h Only qualified installers are allowed to install test and disassemble the camera i The camera is a low v
Download Pdf Manuals
Related Search